Vapamore MR-750 User Manual

Mode d’emploi et manuel de l’utilisateur

SAFETY INFORMATION

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

FAILURE TO FOLLOW SAFETY INFORMATION AND WARNINGS MAY

CAUSE PERMANENT DAMAGE AND VOID PRODUCT WARRANTY.

around water.

use only with a grounded outlet.

Only use distiled water. Using hard water can cause

calcium or mineral build up and void the warranty.

Vapamore in order to prevent a fire hazard.

Do not pull or drag steam cleaner using the steam gun and hose.

Steam cleaner must be level and on the floor during use.

Never use additives such as perfumes, stain removers, or other chemicals in the boiler as they will void the warranty, cause permanent damage, and be dangerous.

Make sure the boiler cap is fully secured pressing down then turning the cap to tighten.

boiler

storage.

boiler

before use by

(See cleaning and storage).

listed on the label.

Drain water tank prior to shipping, transporting.

supply cord.

Do not leave the steam cleaner on and unattended. Always switch the steam cleaner off and remove plug from wall outlet when unattended.

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

PARTS OVERVIEW

PARTS LIST

Measuring cup 700ml

Accessory tool adapter

Nylon brush grout Nylon brush medium Nylon brush large

Metal brush small brass Metal brush large brass Metal brush large stainless steel Cotton cover Large elbow adapter Floor head smooth surface

Water level dip stick MR-750 Ottimo Main Unit

Extension tubes x 2 Detail jet tool

19 20

Bed bug / fabric tool

21 22 23

Horse hair brush small

Horse hair brush large

TECHNICAL SPECIFICATIONS

Model: MR-750 Ottimo Power supply: 120V 60Hz Heating element: 1600w - 13AMP Steam Pressure: 5.2BAR - 75PSI MAX Boiler capacity: 4LTR - 1GAL Heating time full: 20 MIN. Boiler temp: 160C - 320F Steam temp at tip: 140C - 284F PEAK Power cord length: 15’ Steam hose length: 8’ Gross weight: 9KG - 20LBS

GETTING STARTED

Allen Screw

Storage Basket

Rubber washer

Cord Hook

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

Once unpacked the only items that need to be installed are the cord hooks and the storage basket. All the necessary tools and hardware are included to install these items.

Fig.1

Fig.2

CORD HOOKS

There are two supplied cord hooks that are mounted by threading the cord hooks onto the threaded studs located on the back of the steamer housing. The cord hooks rotate by pulling outward from the steamer then twisting to rotate. Use this rotate function to easily remove the power cord and to position the hooks for cord storage. Use the Velcro cord strap to secure the cord during transport. (Fig.1)

STORAGE BASKET

The basket is secured to the main steamer body using the 4 supplied Allen head style screws and rubber washers. Align the basket screw hole locations and with the rubber washer betwwen the basket and the steamer housing, insert the Allen head screws loosely until all screws are in place. Once all screws are in place

(Fig.2)

Vapamore

The Ottimo

if over pressure or over temperature is detected.

machine to cool down before removing tank cap or when changing accessories.

operation. Do not tip or tilt the steam cleaner during use.

ACCESSORIES AND TOOLS

Trigger lock

Extension tubes lock and release

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

Fig.1

Storage bag hook

Fig.2

Accessories twist lock onto the accessory tool adapter

Fig.3

Accessory tool adapter attaches to the steam gun or extension tubes.

Fig.4

Fig.5

Accessory storage basket

Steam hose socket

Use large elbow adapter for floor head.

Use micro fiber pad with floor head.

The MR-750 Ottimo has an accessory storage basket and storage bag. Once all the accessories have been unpacked use the accessory storage bag and basket to carry all the accessories. The storage bag can be hung on the loop on the back of the storage basket. (Fig.1)

The accessory tool adaptor (#4 on parts overview page) is required when using the jet nozzle attachment, detail scraper, and all round detail brushes. Align the accessory with the arrow on the accessory tool adapter and twist to lock into place. The accessory tool adapter can be used directly on the steam gun or can be used with the extension tubes.

(Fig.2 & 3)

The large elbow adaptor (#14 on parts overview page) is required when using the floor head (#15 on parts overview page). With the large elbow adapter facing down, insert into the floor head until completely inserted then rotate up. The adapter will only insert when facing down and then locks into position and allows the adapter to rotate when in use. The large elbow adapter can be used directly on the steam gun or with the extension tubes. Always use the micro fiber pad with the floor head. Wrap the micro fiber pad around the ends of the floor head and hold in place under the spring clips.

(Fig.4)

The detail jet tool and the bed bug / fabric tool (19 & 20 on parts overview page) can be connected directly to the steam gun or the extension tubes. (Fig.5)

STEAM GUN / EXTENSION TUBES

Fig.6

Use with steam gun or extension tubes

The steam gun connects to the steam socket located on the front panel of the machine. Flip the dust cover open and push the hose connector firmly into the socket until both tabs click into place. Remove the steam hose by pressing in both release tabs while pulling out.

(Fig.1)

The steam gun has a trigger (ON) lock located just behind the trigger. This lock can be used for continuous steam without having to hold the trigger. To set the lock, push down the trigger, then while the trigger is down slide the lock to hold the trigger.

Extension tubes can be used for floors or difficult to reach areas. The extension tubes push and lock into place on the steam gun. (Fig.6)

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

Status lights

On/off switch

FILLING & OPERATION

To ll the boiler, switch the steame cleaner to o and remove the plug from the wall outlet. Allow steam cleaner to cool down before removing boiler cap. Unscrew the boiler cap ( Fig. 1) by pressing the cap down and simultaneously turning counter clockwise. Check the water level with the supplied dipstick. Use the supplied funnel

Fill chart for working and heatimg times (water amount -working time - heating time): 700ml - 30-45min. - 5-7 min. / 1400ml - 60-80 min. - 10-12min. / 2100ml - 90-120 min.

- 15-17min. / 2800ml - 150-180min. - 20-22min. (Measuring cup has a 700ml full mark)

Fig.1

Fig.2

Do not ov

Boiler

fill cap

Dip stick

Always use the dipstick to check the

2800ml. If so drain excess water by removing the drain plug to achieve desired water level.

The dipstick has 4 marks, 100% - 2800ml, 75% - 2100ml, 50% -1400ml, 25% - 700ml. This allows options for working time and heating wait time.

Make sure steamer is completely cooled

the cap while the steamer is hot can cause scalding and severe burns.

Replace / close the boiler cap by pressing down on the cap and simultaneously turning it

clockwise. Make sure the cap is fully tight to prevent any steam from leaking out. If

cap fully.

“on” position. The red light on the switch will illuminate. The red status light will illuminate as the heater turns on. The green status light will illuminate indicating the water is fully heated and ready for use. The red and green status lights will cycle on and o during use

Once the green light illuminates the steamer is ready for use. The green

Continue to use the

Fig.3

Use steam controller knob to adjust steam

OUTPUT

output level

Turn the controller knob clockwise to increase the steam output and counter clockwise to reduce the steam output.

(Fig.3)

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

Carpets

‘

’

CLICK

Floor head clicks into extension tubes

OPERATION

Fig.1

extension tube (use 1 to 2 tubes as desired). Ensure

overhanging material under the clips located on each

Fig.2

walls and any hard surface. It can also be used to

Micro fiber pad

sanitize, deodorize, kill allergens, bed bugs and dust

cleaning head to glide when using on carpet. (Fig.3)

Fig.3

Fig.4

Detail jet tool

Jet nozzle on accessory tool adapter

DETAIL JET TOOL / JET NOZZLE

The detail jet tool can be attached directly to the steam gun or to any of the extension tubes. The jet nozzle attachment is used with the accessory tool adapter.

These tools are great for removing soap scum in the bath, shower, and faucets. Also for cleaning tight areas such as toilet seat hinges where high pressure steam can reach and blow out dirt and debris. These

surface being cleaned. The steam temperature will condense and cool within 1’’ of the tool tip. (Fig.4)

GO TO VAPAMORE.COM TO SEE THE MR-750 OTTIMO INSTRUCTIONAL VIDEO

OPERATION

Fig.1

Fig.2

Fig.3

BRUSHES

There are 8 brush types supplied with the Vapamore MR-750 Ottimo. The brushes attach to the accessory tool adapter by aligning the arrows and twisting to lock. Suggested uses (Metal brushes), Oven grills, BBQ grates, cement stains, machinery, and metal surfaces. (Nylon medium duty and large nylon brush), used for more sensitive materials such as blinds, carpet, furniture, air

brush is used for harder less sensitive areas such as

(Horse hair brushes) These brushes are used for sensitive surfaces such as delicate materials, car interiors, and fabrics. (Fig.1/2)

IMPORTANT : With all brushes it is important to not apply excessive pressure or force. This can cause failure of the detail adaptor or related parts. When using the brushes let the steam do the work and the brush to help agitate the stain or area being cleaned. (Fig.1/2)

SCRAPER TOOL

Fig.4

The scraper tool can be used to defrost freezers, on oven walls and cook top surfaces to remove stuck on food. This tool is also good for removing wall paper, paint and shelve paper and gum. (Fig.3)

BED BUG / FABRIC TOOL

Start by installing the supplied cotton cover on the

Bed bug / fabric tool. Now this tool can steaming and sanitizing along with eliminating odors in garments, fabrics, furniture, curtains, drapes, etc. (Fig.4)

Bed bugs, allergens and mold:

Use this tool on bedding, pillows, and furniture by

applying light pressure and slowly passing it along the

surface to kill Bedbugs, dust mites and other allergens.

(See bed bug - dust mite - allergens page for details)

(Fig.4)

be used for

+ 18 hidden pages

Vapamore MR-750 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual