Vapamore MR1000 Instruction Manual

Mode d’emploi et manuel de l’utilisateur

SAFETY INFORMATION

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

FAILURE TO FOLLOW SAFETY INFORMATION AND WARNINGS MAY

CAUSE PERMANENT DAMAGE AND VOID PRODUCT WARRANTY.

around water.

use only with a grounded outlet.

Only use distiled water. Using hard water can cause calcium or mineral build up and void the warranty.

Vapamore in order to prevent a fire hazard.

Do not pull or drag steam cleaner using the steam gun and hose.

Steam cleaner must be level and on the floor during use.

listed on the label.

Never use additives such as perfumes, stain removers, or other chemicals in the water tank as they will void the warranty, cause permanent damage, and be dangerous.

Make sure the water tank cap is fully secured

storage.

before use.

(See cleaning and storage).

Drain water tank prior to shipping, transporting.

supply cord.

Do not leave the steam cleaner on and unattended. Always switch the steam cleaner off and remove plug from wall outlet when unattended.

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

PARTS OVERVIEW

PARTS LIST

Mesh tote basket

Accessory tool adapter

x 2

Nylon brush grout Nylon brush medium Nylon brush large

Metal brush small brass x 4 Metal brush large brass x 4 Metal brush large stainless steel x 4 Cotton cover x 4 Large elbow adapter Floor head with bristles Floor head smooth surface

x 4

Triangle corner brush

Extension tubes x 2

Smooth surface squeegee

Detail jet tool

Bed bug / fabric tool

22 23 24 25

Assembly screws & tools (not shown)

TECHNICAL SPECIFICATIONS

Model: MR-1000 Forza Power supply: 120V 60HZ Heating element: 1900W - 15AMP Steam Pressure: 6BAR - 90PSI PEAK Tank capacity: 8LTR - 2.1GAL Boiler capacity: 4LTR - 1.06 GAL Heating time: 15-20 MIN. Boiler temp: 160C - 320F Steam temp at tip: 140C - 284F PEAK Power cord length: 25’ Steam hose length: 8’ Gross weight: 28.4 KG - 62LBS

GETTING STARTED

Cord Hook

Front Carry Handle

Top Carry Handle

Front Wheel x 4 Bolts

Wheel Bolt

Washer

Rear Wheel

Mesh Tote Basket

Tote Basket Hooks

Thumb Screws

Handle Brackets

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

Once unpacked the items that need to be installed are the front & rear wheels, storage basket with upright handles, front carry handle and cord hooks. All the necessary tools and hardware are included to install these items.

Fig.1

FRONT & REAR WHEEL INSTALLATION

Install the front wheels using the supplied tool along with the supplied wheel bolts, and washers. There are 4 bolts and 4 washers per wheel. (Fig.1) Install the rear wheels using the supplied tool along with the supplied wheel bolts ,and washers. There is

Fig.2

Fig.3

one bolt and one washer per wheel. The rear wheel bolt threads into the wheel mount. (Fig.1)

BASKET & HANDLE

The mesh tote basket is used for parts and accessories and has two large carry handles so items can be carried separate from the machine. There are also small hoops located on the carry basket to hang on the U shape handle. Slid the hooks located on the U shape handle through the small hoops on the mesh tote basket to hang. The U shape handle installs to the rear of the machine by sliding into the brackets located on the rear of the machine housing and then attaches to the machine using the supplied thumb screws. (Fig.2)

CARRY HANDLES & CORD HOOKS

Attach the carry handles using the two supplied bolts for each handle, then tighten with the supplied Allen tool. The cord hooks screw onto the studs located on the back of the machine. Push inward to tighten the cord hooks. The cord hooks rotate by pulling outward from the steamer then twisting to rotate. Use this rotate function to easily remove the power cord and to position the hooks for cord storage. Use the Velcro cord strap to secure the cord during transpor

the steam gun trigger down for 15-20 seconds to release the air trapped in the boiler.

Vapamore

t. (Fig.3)

ACCESSORIES AND TOOLS

Trigger lock

Extension tubes lock and release

Accessory tote basket

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

Fig.1

Fig.2

Accessories twist lock onto the accessory tool adapter

Fig.3

Accessory tool adapter attaches to the steam gun or extension tubes.

Fig.4

Use large elbow adapter for floor heads and triangle brush

Fig.5

Never operate machine without water in the main tank.

The MR-1000 Forza includes a mesh tote basket and mesh storage bag to carry parts and accessories. The mesh tote basket can be removed from the hooks on the machine handle This tota basket includes large carry stapes so you can carry parts and accessories separate from the machine. The handle can also be easily removed to make transport or storage easy.

(Fig.1)

The accessory tool adaptor (#4 on parts overview page) is required when using the jet nozzle attachment, detail scraper, and all round detail brushes (#5-12 on parts overview page). Align the accessory with the arrow on the accessory tool adapter and twist to lock into place. The accessory tool adapter can be used directly on the steam gun or can be used with the extension tubes.

(Fig.2 and 3)

The large elbow adaptor (#14 on parts overview page) is required when using the floor heads or triangle corner brush (#15-17 on parts overview page) With the large elbow adapter facing down, insert into the floor heads or triangle brush until completely inserted then rotate up. The adapter will only insert when facing down and then locks into position and allows the adapter to rotate when in use. The large elbow adapter can be used directly on the steam gun or can be used with the extension tubes.

The smooth surface squeegee, detail jet tool and the

(Fig.4)

bed bug / fabric tool (20-22 on parts overview page) can be connected directly to the steam gun or the extension tubes.

STEAM GUN / EXTENSION TUBES

Fig.6

Use with steam gun or extension tubes

The steam gun connects to the steam socket located on the front panel of the machine. Flip the dust cover open and push the hose connector firmly into the socket until both tabs click into place. Remove the steam hose by pressing in both release tabs while pulling out.

The steam gun has a trigger (ON) lock located just behind the trigger. This lock can be used for continuous steam without having to hold the trigger. To set the lock, push down the trigger, then while the trigger is down slide the lock to hold the trigger.

Extension tubes can be used for floors or difficult to reach areas. The extension tubes push and lock into place on the steam gun. (Fig.6)

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

Do not ov

NOTE:

Do not ov

Cold water tank fill cap

FILLING & OPERATION

GENERAL FUNCTION:

internal components and can cause failure to internal parts and void the warranty.

without this screen in place. Failure to do so will void the warranty.

Fig.1

Fig.2

Use steam knob to

On / off

adjust steam output level

switch

OFF

ST ATUS

Status light

FILL

PRESSURE

Water fill light

the steamer is ready for use. (Initial start up from cold machine is aprox. 15 min) *The status light will cycle red to green during use as the boiler maintains the temperature.

Using additives of any kind will void the warranty.

located on the top of the machine and using the

screen. (Fig.1)

Make sure the steam gun and hose is plugged into the machine before startup. Plug the machine into a proper wall outlet and swit

the pump is running hold the steam gun trigger down

OUTPUT

for 15-20 seconds to release the air trapped in the boiler.

Once the boiler is full the pump will stop and the red status light will light up showing the boiler is now heating the water. Once the boiler is at operating temperature the status light turns to green indicating

The Vapamore MR-1000 Forza has an industry high steam burst pressure of 90 psi. For situations that need a short high pressure steam burst for cleaning, set the the steam output to maximum pressure. For large cleaning areas that need a maintained steady

output knob from the full open position, counter clockwise approximately 1/2 revolution. The steam output knob can be turned down further for delicate jobs that require very little pressure such as jewelry, fabrics, furniture, etc. (Fig.2)

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

Carpets

‘

’

CLICK

Tools click into extension tubes

OPERATION

Fig.1

extension tube (use 1 to 2 tubes as desired). Ensure

overhanging material under the clips located on each

Fig.2

walls and any hard surface. It can also be used to sanitize, deoterize, kill allergens, bed bugs and dust mites. Attach

Micro fiber pad

Fig.3

Fig.4

Fig.5

Detail jet tool

Jet nozzle on accessory tool adapter

Use large elbow adapter for triangle brush

glide when using on carpet. (Fig.3)

or where extra scrubbing strength is needed. (with all bristle or brush tools, let the steam do the work with just light pressure applied to the brush)

TRIANGLE CORNER BRUSH

The triangle corner brush can be used on upholstery,

or tile along with any uneven surface or where extra scrubbing strength is needed. (Fig.4) (with all bristle or brush tools, let the steam do the work with just light pressure applied to the brush)

DETAIL JET TOOL / JET NOZZLE

The detail jet tool can be attached directly to the steam gun or to any of the extension tubes. The jet nozzle attachment is used with the accessory tool adapter.

These tools are great for removing soap scum in the bath, shower, and faucets. Also for cleaning tight areas such as toilet seat hinges where high pressure steam can reach and blow out dirt and debris. These tools are most

cleaned. The steam temperature will condense and cool within 1’’ of the tool tip. (Fig.5)

GO TO VAPAMORE.COM TO SEE THE MR-1000 FORZA INSTRUCTIONAL VIDEO

Sanitize counter tops, tile, stone, granite, glass, stainless steel, walls, etc. Use with extension tubes or direct on gun.

OPERATION

Fig.1

Fig.2

Fig.3

BRUSHES

There are 6 brush types supplied with the Vapamore MR-1000 Forza. The brushes attach to the accessory tool adapter by aligning the arrows and twisting to lock. Suggested uses (Metal brushes), Oven grills, BBQ grates, cement stains, machinery, and metal surfaces. (Nylon medium duty and large nylon brush), used for more sensitive materials such as blinds, carpet, furniture, air

brush is used for harder less sensitive areas such as

IMPORTANT : With all brushes it is important to not apply excessive pressure or force. This can cause failure of the detail adaptor or related parts. When using the brushes let the steam do the work and the brush to help agitate the stain or area being cleaned. (Fig.1/2)

SCRAPER TOOL

The scraper tool can be used to defrost freezers, on oven walls and cook top surfaces to remove stuck on food. This tool is also good for removing wall paper, paint and shelve paper and gum. (Fig.3)

Fig.4

Fig.5

BED BUG / FABRIC TOOL

Start by installing the supplied cotton cover on the Bed bug / fabric tool. Now this tool can

be used for steaming and sanitizing along with eliminating odors in garments, fabrics, furniture, curtains, drapes, etc. (Fig.4)

Bed bugs, allergens and mold: Use this tool on bedding, pillows, and furniture by applying light pressure and slowly passing it along the surface to kill Bedbugs, dust mites and other allergens. (See bed bug - dust mite - allergens page for details) (Fig.4)

SMOOTH SURFACE SQUEEGEE TOOL

Using the smooth surface squeegee tool is great for sanitizing kitchen and bathroom counter tops chemical free along with smooth surfaces such as stone, granite, wood, glass, tile and stainless steel. (Fig.5)

+ 18 hidden pages

Vapamore MR1000 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual