Valor Retrofire RF24XBN, Retrofire RF24XBP Installation And Owner's Manual
US Patent no. 8,166,965
Gravity Vent Fireplace Insert
RF24XBN (NG) & RF24XBP (LPG)
Installation and Owner’s Manual
INSTALLER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury or loss of life.
Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call
the fi re department.
Installation and service must be performed
by a qualifi ed installer, service agency or the
gas supplier.
Leave this manual
with the appliance.
CONSUMER
Retain this manual
for future reference.
Please read this manual BEFORE installing
and operating this appliance.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Massachusetts: The piping and fi nal
gas connection must be performed by a
licensed plumber or gas fi tter in the State of
Massachusetts.
Ce guide est disponible en français sur demande.
MILES INDUSTRIES LTD., British Columbia, Canada
4002862-04
© 2012 Miles Industries Ltd. All rights reserved.
Manufactured by
www.valorfi replaces.com
W
A
R
R
A
N
T
Y
P
R
O
G
R
A
M
V
A
L
O
R
C
O
M
F
O
R
T
V
A
L
O
R
C
O
M
F
O
R
T
Table of Contents
W
A
R
R
A
N
T
Y
P
R
O
G
R
A
M
V
A
L
O
R
C
O
M
F
O
R
T
V
A
L
O
R
C
O
M
F
O
R
T
Table of Contents
FOR THE OWNER
FOR THE OWNER
Safety Precautions ............................................ 3
Safety and Your Fireplace ................................. 4
Owner’s Information .......................................... 5
Remote Control Operation.................................8
Options ............................................................10
Lighting Instructions......................................... 11
Warranty ..........................................................25
FOR THE QUALIFIED INSTALLER
FOR THE QUALIFIED INSTALLER
Warranty Card at the
Warranty Card at the
back of this manual.
back of this manual.
W
W
R
R
O
O
L
L
A
A
V
V
Y
Y
T
T
N
N
A
A
R
R
R
R
A
A
C
C
O
O
M
M
M
M
A
A
R
R
G
G
O
O
R
R
P
P
T
T
R
R
O
O
F
F
Specifi cations ..................................................12
Dimensions ...................................................... 13
Vent Confi gurations .........................................14
Existing Fireplace Preparation.........................15
Supply Gas Installation .................................... 16
Vent Liner Rough-in .........................................17
Appliance Preparation .....................................17
Firebox Installation .......................................... 18
Ceramic Logs Installation ................................21
Window Refi tting and Checking.......................22
Remote Control Installation .............................22
Operation Check and Aeration Adjustment......23
Vent Check ......................................................23
Optional Cast Iron Fret Installation ..................24
Optional Bottom Cover Installation ..................24
Warranty ..........................................................25
Spare Parts......................................................26
The information contained in this installation
The information contained in this installation
manual is believed to be correct at the time of
manual is believed to be correct at the time of
printing. Miles Industries Ltd. reserves the right
printing. Miles Industries Ltd. reserves the right
to change or modify any information or specifi ca-
to change or modify any information or specifi ca-
tions without notice. Miles Industries Ltd. grants
tions without notice. Miles Industries Ltd. grants
no warranty, implied or stated, for the installation
no warranty, implied or stated, for the installation
or maintenance of your heater, and assumes no
or maintenance of your heater, and assumes no
responsibility for any consequential damage(s).
responsibility for any consequential damage(s).
190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1
2
Designed and Manufactured by / for
Miles Industries Ltd.
Tel. 604-984-3496 Fax 604-984-0246
www.valorfi replaces.com
© Copyright Miles Industries Ltd., 2012
Safety Precautions
!
READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO FOLLOW
these installation instructions may result in possible fi re
hazard and will void the warranty.
Prior to the fi rst fi ring of the fi replace, READ the
Owner’s Information section of this manual.
DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualifi ed service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
Installation and repair should be PERFORMED by a
qualifi ed service person. The appliance and venting
system should be INSPECTED before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.
Always KEEP the appliance clear and free from
combustible materials, gasoline, and other fl ammable
vapors and liquids.
NEVER OBSTRUCT the fl ow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.
Due to the high temperature, the appliance should be
LOCATED out of traffi c areas and away from furniture
and draperies. Clothing or fl ammable material SHOULD
NOT BE PLACED on or near the appliance.
Clothing or fl ammable material SHOULD NOT BE
PLACED on or near the appliance.
Children and adults should be ALERTED to the hazards
of high surface temperature and should STAY AWAY to
avoid burns or clothing ignition.
YOUNG CHILDREN should be CAREFULLY
SUPERVISED when they are in the same room as
the appliance. Toddlers, young children and others
may be susceptible to ACCIDENTAL CONTACT
BURNS. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access
to a fi replace or stove, INSTALL AN ADJUSTABLE
SAFETY GATE to keep toddlers, young children and
other at risk individuals out of the room and away from
hot surfaces.
This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent
system or components MAY BE USED.
This gas fi replace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate
vent system. Common vent systems are PROHIBITED.
INSPECT the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air fl ow.
The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.
DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualifi ed
service person. DO NOT strike or slam the glass door.
The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the fi replace
manufacturer. NO SUBSTITUTE material may be used.
DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.
TURN OFF the gas before servicing this appliance.
It is recommended that a qualifi ed service technician
perform an appliance check-up at the beginning of each
heating season.
Any safety screen or guard removed for servicing
MUST BE REPLACED prior to operating this appliance.
DO NOT place furniture or any other combustible
household objects within 36” of the fi replace front.
BE CAREFUL not to put any decorating objects
sensitive to heat to close above or around the fi replace
as it gets very hot when operating.
DO NOT use this heater as a temporary source of heat
during construction.
This appliance is a DOMESTIC ROOM-HEATING AP-
PLIANCE. It must not be used for any other purposes
such as drying clothes, etc.
State of California. Proposition 65 Warning. Fuels
used in gas, wood-burning or oil fi red appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.
3
Safety and Your Fireplace
!
Safety and Your Fireplace
Please Read and Carefully Follow all Safety Warnings and
Operating Instructions Contained in Your Owners Manual
(Replacement Manuals are available by contacting our service department at
1-800-468-2567 or visit www.valorfi replaces.com).
Please Follow These Important
Child Safety Precautions and
Recommendations,
• Parts of your Valor Fireplace become
extremely hot while in operation.
• The glass viewing window
temperature can
exceed 500 F
at full capacity.
Momentary contact
with a hot glass
surface can cause
a severe burn, even if the fi replace
is operating at reduced heating
capacity.
• The glass window will remain hot
for an extended period of time after
the fi replace has been turned off.
Ensure that children are prevented
from touching the fi replace during the
cool down period.
• Toddlers and Young Children
must be closely supervised at all
times when they are in the same
room as the operating fi replace. They
lack full awareness of danger and
rely on your protection. Toddlers,
in particular, do not have the motor
skills and response refl exes to
withdraw in the event of accidental
contact with a hot surface.
• A physical barrier is strongly
recommended if there are young
children, or at-risk individuals in the
house. Install an approved aftermarket safety gate to keep toddlers,
young children and other at-risk
individuals a safe distance from the
fi replace.
• Keep the remote control handset
out of reach of children at all
times. A wall mount storage holster
is provided with your remote control
handset.
• Ensure that the fi replace, including
the pilot light, is completely turned
off when children are present and
close supervision and safety barriers
are not available—see page 7 of
Owner’s Information section.
• If the fi replace is not going to be used
for the summer or any extended
period of time, remove the batteries
from the remote control handset
and receiver. It is recommended that
batteries are replaced annually in any
event—see page 7.
4
Owner’s Information
• • HOT HEARTH / FLOOR!
The hearth or fl oor
in front of the fi replace may become very hot
when the fi replace heats. Do not use the hearth
as a seat or shelf.
• • Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fi replace.
AVOID PLACING
candles, paintings, photos,
and other items
SENSITIVE TO HEAT
• • Solid wood fl ooring in front of the fi replace (if
allowed) may shrink during the heating season
due to heat.
OWNER’S
INFORMATION
WARNING
!
EXTREMELY HOT!!!
• READ the SAFETY information on pages
3 and 4 of this manual BEFORE operating
your gas heater.
• Some parts of your fi replace are EXTREMELY
HOT, particularly the GLASS window.
• DO NOT LET CHILDREN touch the glass or
any parts of your fi replace even after it is
turned off as it is still hot.
• USE A SAFETY SCREEN or a GATE to reduce
the risk of severe burns.
• Keep the remote control handset OUT OF
REACH of children.
HOT HEARTH / FLOOR!
in front of the fi replace may become very hot
when the fi replace heats. Do not use the hearth
as a seat or shelf.
Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fi replace.
AVOID PLACING
and other items
36 inches (0.9 m) around the fi replace.
Solid wood fl ooring in front of the fi replace (if
allowed) may shrink during the heating season
due to heat.
Performance of LPG appliances may be affected
by the quality of commercial gas supplied in
your area.
candles, paintings, photos,
SENSITIVE TO HEAT within
The hearth or fl oor
Fireplace
Hearth
Do not put
furniture or other objects
in this space in front of
the replace:
36” (0.9 m)
Thank You ...
For purchasing a Valor by Miles Industries. Your new
radiant gas heater is a technical appliance that must
be installed by a qualifi ed dealer. Each Valor fi replace
is fully tested during the production process for your
safety and comfort.
Your unit has been professionally installed by:
Dealer Name: ________________________________
Phone Number :_______________________________
Should you encounter an operational problem, call
your dealer immediately.
Do not try to repair the unit as you may cause an
injury or damage the fi replace.
This manual and particularly the preceeding
and following pages contain very important
information regarding the safe operation of your
fi replace as well as maintenance instructions.
Read carefully BEFORE operating your fi replace
and pay special attention to the SAFETY
WARNINGS.
A heating gas appliance does require safe handling
and for this reason, we very strongly recommend that
no children be allowed to touch the fi replace and its
controls at all times. Do install a screen or barrier
in front of the fi replace to protect your children
against severe burns.
Operating Your Fireplace for the First Time
When operating your new fi replace for the fi rst time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the fl ames to be the full height of the fi rebox, or
even slightly higher, for the fi rst few hours of operation.
It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the fl ames will be at their normal height.
Flame Supervision Device
For your safety, this appliance is fi tted with a fl ame
supervision device which will shut-off the gas supply
if, for any reason, the pilot fl ame goes out. This device
incorporates a fi xed probe, which senses the heat
from the pilot fl ame. If the probe is cool, the device will
prevent any gas fl ow unless manually lighting the pilot.
See full lighting instructions on page 11 of this manual.
5
OWNER’S
Spring-loaded
Fastening Studs (2)
1/4 Turn
DO NOT TOUCH THE GLASS WHILE IT IS HOT!
Let the fi replace cool fi rst before cleaning it.
INFORMATION
Owner’s Information
Cleaning
WARNING
!
DO NOT TOUCH THE GLASS WHILE IT IS HOT!
Let the fi replace cool fi rst before cleaning it.
Important - Glass cleaning - Mineral deposits
One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white fi lm on the ceramic glass of the viewing door.
The composition of the deposit varies widely from
various locations and also from time to time in the same
location. It seems this is associated with the varying
sulfur content of the gas. You may have the problem for
a time and then not see it for many months when it will
reappear in your area.
We have discussed this problem with ceramic glass
manufacturers and they cannot give us a defi nitive
answer to this problem. Dealers have tried various
cleaning products with varying results. The following
recommendations will not guarantee results in your
particular case.
NOTE: This is a problem beyond Miles Industries’
control and is not covered under warranty.
• Clean the glass regularly as soon as you notice
the buildup (white fi lm). If the fi lm is left for a longer
period of time, it will bake on. It is then much harder,
if not impossible, to remove.
• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the
immediate effect of compromising the strength of the
glass. An emulsion type cleaner is recommended.
• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive
to ceramic glass and should be avoided.
• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.
» BRASSO, POLISH PLUS by KELKEM, COOK TOP CLEAN CREME
by ELCO, WHITE OFF by RUTLAND, TURTLE WAX
Do not clean the glass while it is hot.
Always securely replace the window before lighting.
If broken, the glass pane may only be replaced
as a complete window unit as supplied by the
manufacturer.
It is necessary to remove the cast iron fret and
brackets or the bottom cover before removing the
window—see previous installation sections.
The window can be removed for cleaning by rotating
the two fastening studs at the bottom corners 90
degrees to release, and swinging the bottom of the
window unit outwards to unhook the top edge.
If the Hot Glass Warning plate has been removed
from the front lower corner of the window, reinstall
it by sliding it between the glass and the frame as
indicated.
Hot Glass Plate
Dust, etc. can be brushed from the ceramic fuel effects
and fi rebox walls after removing the front unit and
opening the window. Dust etc. can also be removed
from the burner using a soft brush after removing the
ceramic fuel effects. When cleaning, make sure that
no particles are brushed into the slots in the burner.
6
Owner’s Information
Pilot Flame
Thermocouple
Probe must be
in Flame
OWNER’S
INFORMATION
Checks
A periodic check of the pilot and burner fl ames should
be made. Check after the fi re has been on for at least
30 minutes. The pilot fl ame must cover the tip of the
thermocouple probe. The main burner fl ame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions—see images below.
Correct Flame Picture
The appliance area must always be kept clear and
free from combustible materials, gasoline and other
fl ammable vapors and liquids. Inspect the vent terminal
outdoors regularly to make sure that, snow, leaves,
bushes, trees, etc, do not obstruct it. Examine the vent
system and terminal regularly. We recommend annually.
Batteries
Low batteries signal: see page 10.
To replace the batteries in the remote control
receiver:
1. The receiver is located to the left of the valve and it
is retained to the fi rebox by a Velcro tab. Grab the
receiver and pull it out from its location.
2. Slide and remove the receiver cover.
3. Replace the 4 AA alkaline batteries.
4. Replace the cover.
5. Put the receiver back in its position pushing it in so
it attaches to the Velcro tab.
Lighting, Operation and Rating Information
WARNING
!
DO NOT ATTEMPT TO TOUCH THE DATA PLATE
WHILE THE FIREPLACE IS STILL HOT! Let the
fi replace cool fi rst before touching it.
The Lighting, Operation and Rating information is located
on a plate at the left of the valve under the burner.
To access the plate, remove the cast fret or the bottom
cover, grab the plate and take it out to read it. There is
important information on both sides of the plate.
How to Turn Your Fireplace OFF (including pilot)
WARNING
!
DO NOT ATTEMPT TO CHANGE THE BATTERIES WHILE THE FIREPLACE IS STILL HOT! Let
the fi replace cool fi rst before touching it.
CAUTION
DO NOT USE a screwdriver or other metallic object to
remove the batteries from the receiver or the handset!
This could cause a short circuit to the receiver.
The remote control receiver of the appliance uses four
alkaline 1.5 V AA batteries and the handset uses one
9 V alkaline battery.
Batteries should last one to two seasons, depending
on usage. Removing the batteries in the off-season
will extend the battery life. Should the batteries loose
power, the control may be operated by manually
turning the control knob at the valve.
First, ensure your fi replace is cooled BEFORE
going ahead.
Locate the gas valve under the fi rebox.
1. Set the Flame Adjustment Knob clockwise
as far
as possible.
2. Push in the Gas Control Knob slightly and turn it
clockwise to OFF. Do not force.
Flame
Adjustment
Knob
Turn gas valve buttons clockwise
to turn fi replace OFF.
Gas
Control
Knob
How to Ensure Your Fireplace Cannot
Be Turned ON Inadvertently
The best way to ensure your fi replace will not turn on is
to turn it off, including pilot—see above.
If you wish to maintain the pilot only without the main
burner coming on, turn the Gas Control Knob to Pilot
position.
7
OWNER’S
INFORMATION
Owner’s Information
Servicing
If any attention is required for your appliance, contact
your supplier quoting the model number. It will be
helpful if the appliance’s serial number can also be
quoted. This number is on the rating plate, which is
located under the burner.
The replacement parts are shown at the end of this
manual. Please always quote the part number and
description when requesting spare parts.
Vent Safety Switch
This appliance is equipped with a vent safety switch
which, when activated, will turn off the burner and
pilot if the vent is blocked, disconnected, or if there is
excessive down draught.
If the safety switch is activated, wait for it to cool off
before trying to light the appliance again. The safety
Remote Control Operation
switch will cool off and reset itself automatically after
25 to 30 minutes.
In the event that the safety switch is activated
again, contact a qualifi ed service technician for
inspection.
Should the safety switch require replacement, only
use parts supplied by Miles Industries.
Your fi replace remote control helps you get the comfort, convenience and aesthetics
you want from your gas fi replace. The remote controls your fi replace in different
ways.
IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings
of time, temperature and automatic ON/OFF can only be programmed when the
function display is fl ashing. Be patient when programming as it can take a few
seconds to set.
Setting the time
The fi rst thing to do is to set the time.
1. With your thumb, hold down both the AUTO and TIMER buttons until F fl ashes.
Let go.
2. Note the digital clock on the bottom right hand corner. The ▲ button sets the
hour; the ▼ button sets the minutes. Set the time.
Note: You must start setting the time while the F is fl ashing. If it stops fl ashing,
go back to 1.
3. The display shows °C/24-hour or °F/12-hour. To change the temperature/hour
display, press on the AUTO button while the display fl ashes.
4. Let go and wait until the fl ashing stops. The remote shows the time you set. It
also shows the current temperature.
8
Remote Control Operation
Setting the temperature
Use this setting when you come in and want to enjoy a specifi c temperature.
1. Push the AUTO button until a number and F fl ash. Let go.
2. While it is still fl ashing, push the ▲ and ▼ buttons to the temperature you want.
Let go.
Your fi replace will reach that temperature and the remote will check the temperature
every fi ve minutes, adjusting the amount of fuel needed to give you a steady, even heat.
Setting the fl ame
Use this setting when you want a particular fl ame level. For instance, you want to
watch fl ames burn at their highest level and you don’t mind if the room is too hot.
1. To raise the fl ame, press and hold the ▲ button until the flame gets to the
desired level. Let go.
2. To lower the fl ame, press and hold the ▼ button until the fl ame gets to the
desired level. Let go.
The fl ame level will remain just as you set it.
OWNER’S
INFORMATION
Programming time and temperature
You can set your fi replace to come on before you wake up and turn off after you leave
and then, turn on again just before you come home and turn off after going to bed.
You can leave it like this for the heating season.
1. Decide what temperature you want your fi replace to be at. Also, decide what time
you want your fi replace to turn on and off. Finally, decide what time you want it to
come back on and off in the afternoon or evening. For the fi rst few times you set
the timer, it’s handy to write these times down.
2. Set the temperature (just as you did in the section Setting the temperature.)
3. Press the TIMER button and hold it until P1
While fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at
which you want your fi replace to turn on in the morning.
4. Press the TIMER button and hold it until P1 ☽ appears and fl ashes. Let go. While
fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at which you
want your fi replace to turn off when you leave.
5. Press the TIMER button and hold it until P2
While fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at
which you want your fi replace will turn back on in the afternoon.
6. Press the TIMER button and hold it until P2 ☽ appears and fl ashes. Let go. While
fl ashing, push the buttons ▲ (hour) and ▼ (minutes) to set the time at which you
want your fi replace to turn off in the evening.
7. That is all you have to do. Your fi replace will give you steady, even heat at the
temperatures and times you set.
Note: If you want to set your fi replace for only one time on and off, set P2
for the same times as P1 ☽. The remote will record the P1 ☽ off time for both P2 times.
To temporarily override the timer setting, just press AUTO or ▲ and ▼ to go back to
manual settings. Press TIMER to go back to your settings.
☼ appears and flashes. Let go.
☼ appears and fl ashes. Let go.
☼ and P2 ☽
9
Loading...