Valor RETROFIRE RF24IDN, RETROFIRE RF24IDP Installation And Owner's Manual
RETROFIRE
Direct Vent Fireplace Insert
RF24IDN (NG) & RF24IDP (LPG)
Installation and Owner’s Manual
US Patent no. 8,166,965
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.
! WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
— Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do
not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
▪ If you cannot reach your gas supplier,
call the fi re department.
— Installation and service must be
performed by a qualifi ed installer, service
agency or the gas supplier.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Massachusetts: The piping and fi nal
gas connection must be performed by a
licensed plumber or gas fi tter in the State of
Massachusetts.
Ce guide est disponible en français sur demande.
INSTALLER
Leave this manual
with the appliance.
CONSUMER
Retain this manual
for future reference.
Please read this manual
BEFORE installing and
operating this appliance.
4002315-16
© 2014 Miles Industries Ltd. All rights reserved.
Table of ContentsTable of Contents
W
A
R
R
A
N
T
Y
P
R
O
G
R
A
M
V
A
L
O
R
C
O
M
F
O
R
T
V
A
L
O
R
C
O
M
F
O
R
T
FOR THE OWNER FOR THE QUALIFIED INSTALLER
Safety Precautions .................................................3
Safety and Your Fireplace ...................................... 4
Owner’s Information ............................................... 5
Operating Your Fireplace for the First Time ............... 5
Cleaning Your Fireplace ............................................ 6
Checking Pilot and Burner Flames ............................7
Using Handset Wall Holder ........................................ 7
Replacing Batteries ...................................................8
Locating Lighting, Operation and
Rating Information Plate .........................................8
Servicing Your Fireplace ............................................8
Operating Your Fireplace ...........................................8
How to Turn Your Fireplace OFF
(including pilot) .....8
How to Ensure Your Fireplace Cannot
Be Turned ON Inadvertently ...................................9
Remote Control Operation ................................... 10
Options .................................................................. 14
Lighting Instructions ............................................ 15
Warranty ................................................................33
R
O
M
L
A
R
A
G
Warranty Card at the
back of this manual.
W
O
V
R
P
Y
T
T
N
A
R
R
R
A
O
C
F
O
M
Specifi cations .......................................................16
Dimensions ........................................................... 17
Vent Confi gurations .............................................18
Vent Termination ................................................... 19
Existing Fireplace Preparation ............................ 21
Installation ............................................................. 22
Connect Gas Supply ................................................ 22
Rough-in Vent Liners ...............................................23
Prepare Appliance ...................................................23
Connect Vent Liners to Appliance ............................ 24
Re-install Support Legs (if removed) ....................... 24
Level Firebox in Hearth ...........................................25
Re-install Burner Module ......................................... 25
Connect Gas Line and Test Appliance ..................... 25
Re-install Top Baffl e (if removed) ............................ 25
Install Top Convection Baffl e ...................................26
Install Ceramic Log Set ...........................................26
Refi t and Check Window ......................................... 27
Synchronize Remote Control ................................... 28
Check Operation ...................................................... 28
Adjust Aeration (if necessary) .................................. 28
Install Barrier Screen ............................................... 29
Install Cast Iron Fret or Bottom Cover ..................... 29
Install Handset Wall Holder ..................................... 30
Wiring Diagram ..................................................... 31
Approved Venting Components .......................... 32
Warranty ................................................................33
Spare Parts............................................................34
Massachusetts: The piping and fi nal
gas connection must be performed by a
licensed plumber or gas fi tter in the State
of Massachusetts.
190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1
2
The information contained in this installation
manual is believed to be correct at the time of
printing. Miles Industries Ltd. reserves the right
to change or modify any information or specifi cations without notice. Miles Industries Ltd.
grants no warranty, implied or stated, for the
installation or maintenance of your heater, and
assumes no responsibility for any consequential
damage(s).
Designed and Manufactured by / for
Miles Industries Ltd.
Tel. 604-984-3496 Fax 604-984-0246
www.valorfi replaces.com
© Copyright Miles Industries Ltd., 2014
Safety Precautions
!
READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO FOLLOW
these installation instructions may result in possible fi re
hazard and will void the warranty.
Prior to the fi rst fi ring of the fi replace, READ the
Owner’s Information section of this manual.
DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualifi ed service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
Installation and repair should be PERFORMED by a
qualifi ed service person. The appliance and venting
system should be INSPECTED before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.
Always KEEP the appliance clear and free from
combustible materials, gasoline, and other fl ammable
vapors and liquids.
NEVER OBSTRUCT the fl ow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.
This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent
system or components MAY BE USED.
This gas fi replace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate
vent system. Common vent systems are PROHIBITED.
INSPECT the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air fl ow.
TURN OFF the gas before servicing this appliance.
It is recommended that a qualifi ed service technician
perform an appliance check-up at the beginning of each
heating season.
DO NOT use this heater as a temporary source of heat
during construction.
State of California. Proposition 65 Warning. Fuels
used in gas, wood-burning or oil fi red appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.
Due to the high temperature, the appliance should be
LOCATED out of traffi c areas and away from furniture
and draperies.
Clothing or fl ammable material SHOULD NOT BE
PLACED on or near the appliance.
This appliance is a DOMESTIC ROOM-HEATING AP-
PLIANCE. It must not be used for any other purposes
such as drying clothes, etc.
DO NOT place furniture or any other combustible
household objects within 36” of the fi replace front.
BE CAREFUL not to put any decorating objects
sensitive to heat to close above or around the fi replace
as it gets very hot when operating.
The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.
DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualifi ed
service person. DO NOT strike or slam the glass door.
The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the fi replace
manufacturer. NO SUBSTITUTE material may be used.
DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.
A BARRIER DESIGNED TO REDUCE THE RISK OF
BURNS from the hot viewing glass is provided with
this appliance and SHALL BE INSTALLED for the
PROTECTION OF CHILDREN and other AT-RISK
INDIVIDUALS.
If the barrier becomes damaged, the barrier SHALL BE
REPLACED with the MANUFACTURER’S BARRIER
for this appliance.
Any safety screen, guard or barrier removed for servicing the appliance, MUST BE REPLACED prior to
operating the appliance.
Children and adults should be ALERTED to the hazards
of high surface temperature and should STAY AWAY to
avoid burns or clothing ignition.
YOUNG CHILDREN should be CAREFULLY
SUPERVISED when they are in the same room as the
appliance. Toddlers, young children and others may
be susceptible to ACCIDENTAL CONTACT BURNS.
A physical barrier is recommended if there are at-risk
individuals in the house. To restrict access to a fi replace
or stove, INSTALL AN ADJUSTABLE SAFETY GATE
to keep toddlers, young children and other at-risk
individuals out of the room and away from hot surfaces.
3
Safety and Your Fireplace
Safety and Your Fireplace
Please Read and Carefully Follow all Safety Warnings and
Operating Instructions Contained in Your Owner’s Manual
(Replacement Manuals are available by contacting our service department at
1-800-468-2567 or visit www.valorfi replaces.com).
Please Follow These Important
Child Safety Precautions and
Recommendations,
• Parts of your Valor Fireplace become
extremely hot while in operation.
• The glass
viewing window
temperature can
exceed 500 F
at full capacity.
Momentary contact
with a hot glass surface can cause
a severe burn, even if the fi replace
is operating at reduced heating
capacity.
• The glass window will remain hot
for an extended period of time after
the fi replace has been turned off.
Ensure that children are prevented
from touching the fi replace during the
cool down period.
skills and response refl exes to
withdraw in the event of accidental
contact with a hot surface.
• A physical barrier is strongly
recommended if there are young
children, or at-risk individuals in the
house. Install an approved aftermarket safety gate to keep toddlers,
young children and other at-risk
individuals a safe distance from the
fi replace.
• Keep the remote control handset
out of reach of children at all
times. A wall mount storage holster
is provided with your remote control
handset.
• Ensure that the fi replace, including
the pilot light, is completely turned
off when children are present and
close supervision and safety barriers
are not available—see pages 8–9 of
Owner’s Information section.
• Toddlers and Young Children
must be closely supervised at all
times when they are in the same
room as the operating fi replace. They
lack full awareness of danger and
rely on your protection. Toddlers,
in particular, do not have the motor
4
• If the fi replace is not going to be used
for the summer or any extended
period of time, remove the batteries
from the remote control handset
and receiver. It is recommended that
batteries are replaced annually in any
event—see page 8.
Owner’s Information
• • Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fi replace.
AVOID PLACING
candles, paintings, photos,
and other items
SENSITIVE TO HEAT
• • Solid wood fl ooring in front of the fi replace (if
allowed) may shrink during the heating season
due to heat.
OWNER’S
INFORMATION
WARNING
!
EXTREMELY HOT!!!
• READ the SAFETY information on pages
3 and 4 of this manual BEFORE operating
your gas heater.
• Some parts of your fi replace are EXTREMELY
HOT, particularly the GLASS window.
• DO NOT LET CHILDREN touch the glass or
any parts of your fi replace even after it is
turned off as it is still hot.
• USE THE BARRIER SCREEN provided with
the appliance, front or trim or a GATE to
reduce the risk of burns.
• Keep the remote control handset OUT OF
REACH of children.
• HOT HEARTH/FLOOR SURFACE! The
hearth or fl oor directly in front of the fi replace
is VERY HOT when the fi replace heats. Even
if constructed of non-combustible materials,
and although safe, it may reach temperatures
in excess of 200º F depending on choice of
materials. DO NOT STEP ON IT!
Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fi replace.
AVOID PLACING
and other items
36 inches (0.9 m) around the fi replace.
Solid wood fl ooring in front of the fi replace (if
allowed) may shrink during the heating season
due to heat.
Performance of LPG appliances may be affected by
the quality of commercial gas supplied in your area.
candles, paintings, photos,
SENSITIVE TO HEAT within
Fireplace
Hearth
Do not put
furniture or other objects
in this space in front of
the replace:
36” (0.9 m)
Thank You ...
For purchasing a Valor by Miles Industries. Your new
radiant gas heater is a technical appliance that must
be installed by a qualifi ed dealer. Each Valor fi replace
is fully tested during the production process for your
safety and comfort.
Your unit has been professionally installed by:
Dealer Name: ________________________________
Phone Number :_______________________________
Should you encounter an operational problem, call
your dealer immediately.
Do not try to repair the unit as you may cause an
injury or damage the fi replace.
This manual and particularly the preceeding
and following pages contain very important
information regarding the safe operation of your
fi replace as well as maintenance instructions.
Read carefully BEFORE operating your fi replace
and pay special attention to the SAFETY
WARNINGS.
A heating gas appliance does require safe handling
and for this reason, we very strongly recommend that
no children be allowed to touch the fi replace and its
controls at all times. Do install a screen or barrier
in front of the fi replace to protect your children
against severe burns.
Operating Your Fireplace for the First Time
When operating your new fi replace for the fi rst time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the fl ames to be the full height of the fi rebox, or
even slightly higher, for the fi rst few hours of operation.
It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the fl ames will be at their normal height.
Flame Supervision Device
For your safety, this appliance is fi tted with a fl ame
supervision device which will shut-off the gas supply
if, for any reason, the pilot fl ame goes out. This device
incorporates a fi xed probe, which senses the heat
from the pilot fl ame. If the probe is cool, the device will
prevent any gas fl ow unless manually lighting the pilot.
See full lighting instructions on page 15 of this manual.
5
OWNER’S
INFORMATION
Owner’s Information
Cleaning Your Fireplace
WARNING
!
DO NOT TOUCH THE GLASS WHILE IT IS HOT!
Let the fi replace cool fi rst before cleaning it.
Important - Glass cleaning - Mineral deposits
One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white fi lm on the ceramic glass of the viewing door.
The composition of the deposit varies widely from
various locations and also from time to time in the same
location. It seems this is associated with the varying
sulfur content of the gas. You may have the problem for
a time and then not see it for many months when it will
reappear in your area.
We have discussed this problem with ceramic glass
manufacturers and they cannot give us a defi nitive
answer to this problem. Dealers have tried various
cleaning products with varying results. The following
recommendations will not guarantee results in your
particular case.
NOTE: This is a problem beyond Miles Industries’
control and is not covered under warranty.
• Clean the glass regularly as soon as you notice
the buildup (white fi lm). If the fi lm is left for a longer
period of time, it will bake on. It is then much harder,
if not impossible, to remove.
• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the
immediate effect of compromising the strength of the
glass. An emulsion type cleaner is recommended.
• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive
to ceramic glass and should be avoided.
• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.
• BRASSO, POLISH PLUS by KELKEM, COOK TOP CLEAN CREME
by ELCO, WHITE OFF by RUTLAND, TURTLE WAX
Do not clean the glass while it is hot!
Always securely replace the window and the barrier
screen before lighting.
If broken, the glass pane may only be replaced
as a complete window unit as supplied by the
manufacturer.
If the barrier becomes damaged, the barrier shall
be replaced with the manufacturer’s barrier for this
appliance.
It is necessary to unhook the cast iron fret and
brackets or the bottom cover, as well as the barrier
screen before removing the window for cleaning.
WARNING
!
WARNING
DO NOT TOUCH THE BARRIER SCREEN OR
FIREPLACE WHILE THEY ARE HOT! Let the
fi replace cool fi rst before cleaning it.
1. Remove the barrier screen.
a. Open the top brackets outwards to unhook the
screen top.
b. Unhook the bottom of the screen from the
window frame.
2. Clean the barrier screen with a soft brush.
3. Remove the window for cleaning.
a. Rotate the two fastening studs at the bottom
corners 90 degrees to release them.
b. Swing the bottom of the window outwards to
unhook the top edge.
4. Clean the window glass following the guidelines
indicated in this section.
5. Dust the ceramic fuel effects and fi rebox walls using
a soft brush.
6. Dust the burner using a soft brush after removing the
ceramic fuel effects. When cleaning, make sure
that no particles are brushed into the slots in the
burner.
6
Owner’s Information
Pilot Flame
Thermocouple
Probe must be
in Flame
Check that Window
Moves Freely After
Reinstallation
Spring Loaded
Fastening Studs (2)
1/4 Turn
OWNER’S
INFORMATION
7. Reinstall the window.
a. Hook the window over the top edge of the fi rebox,
and fasten the bottom two spring- loaded bolts by
pushing in and turning them 90 degrees.
IMPORTANT: To ensure a safe operation, verify that
the bolts are hooked properly to the window tabs;
then, pull out the bottom of the window and release it
to insure the springs return it.
b. Apply light hand pressure against the window
frame sides to bed-in the window seal.
c. If the Hot Glass Warning plate has been
removed from the front lower corner of the
window, reinstall it by sliding it between the
glass and the frame as indicated.
a. Hook the bottom of the screen to the bottom
edge of the window frame and then push the
screen against the window frame.
Convection baffl e
Top view—Hook bottom of screen to bottom of
window frame
b. Push the top of the screen against the top of the
window frame and while holding it bend the top
brackets around the window frame to secure the
screen. Check that the screen is solidly hooked
to the window frame.
Hot Glass Plate
8. Reinstall the barrier screen.
WARNING
!
FOR SAFETY PURPOSE, ensure the barrier
screen is re-installed on the fi replace window
after maintenance.
Checking Pilot and Burner Flames
A periodic check of the pilot and burner fl ames should
be made. Check after the fi re has been on for at least
30 minutes. The pilot fl ame must cover the tip of the
thermocouple probe. The main burner fl ame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions—see images below.
Correct Flame Picture
The appliance area must always be kept clear and
free from combustible materials, gasoline and other
fl ammable vapors and liquids.
Inspect the vent terminal outdoors regularly to make
sure that, snow, leaves, bushes, trees, etc, do not
obstruct it.
Examine the vent system and terminal regularly. We
recommend annually.
7
OWNER’S
INFORMATION
Owner’s Information
Using Handset Wall Holder
Your fi replace equipment includes a wall
holder to store the handset. If it hasn’t be
installed, refer to the instructions further on
in this manual for the installation.
Replacing Batteries
WARNING
!
DO NOT ATTEMPT TO CHANGE THE BATTERIES WHILE THE FIREPLACE IS STILL HOT! Let
the fi replace cool fi rst before touching it.
CAUTION
DO NOT USE a screwdriver or other metallic object to
remove the batteries from the receiver or the handset!
This could cause a short circuit to the receiver.
Low batteries signal: see page 14.
BEFORE changing the batteries, turn off the valve
using the manual On/Off switch —see instructions on
the following page.
The appliance uses four alkaline 1.5 V AA batteries
for its remote control receiver and one 9 V alkaline
battery for its handset. Batteries should last one to two
seasons, depending on usage. Removing the batteries
in the off-season will extend the battery life. Should the
batteries loose power, the control may be operated by
manually turning the control knob at the valve or by
turning off the valve at the switch.
To replace the batteries in the remote control
receiver:
1. The receiver is located to the left of the valve and
it is retained to the fi rebox by a Velcro tab. Grab
the receiver and pull it out from its location.
2. Slide and remove the receiver cover.
3. Replace the batteries with 4 AA alkaline batteries.
4. Replace the cover.
5. Put the receiver back in its position pushing it in
so it attaches to the Velcro tab.
cover, grab the plate and take it out to read it. There is
important information on both sides of the plate.
Servicing Your Fireplace
If any attention is required for your appliance, contact
your supplier quoting the model number. It will be helpful
if the appliance’s serial number can also be quoted. This
number is on the rating plate, which is located under the
burner. The replacement parts are shown at the end of
this manual. Please always quote the part number and
description when requesting spare parts.
Operating Your Fireplace
There are three ways to control your fi replace.
1. Thermostatic Remote Control;
2. Wall Switch (optional);
3. Manual On/Off Switch.
The manual On/Off switch must be ON for the fi replace
to function. It can be used to shut off the fi replace in
case of emergency—see next section.
The Thermostatic Remote Control can be programmed
to function automatically—see pages 10–14.
The Wall Switch (optional) can be used to turn on, off
and to increase or decrease the fl ame height—see
1265WSK—Wall Switch Kit.
NOTE: The remote control in the AUTO mode will
override the wall switch.
How to Turn Your Fireplace OFF (including pilot)
ON
OFF
Remote Control
Wall Switch
(optional)
Manual On/Off SwitchThermostatic
Locating Lighting, Operation and Rating
Information Plate
The Lighting, Operation and Rating information plate is
WARNING
!
DO NOT ATTEMPT TO TOUCH THE DATA PLATE
WHILE THE FIREPLACE IS STILL HOT! Let the
fi replace cool fi rst before touching it.
located at the left of the valve under the burner.
To access the plate, remove the cast fret or the bottom
8
Owner’s Information
Familiarize yourself with each of these methods before
operating your fi replace.
Handset and Wall Switch: Press and hold the OFF
button for a second.
If the fl ames are on, they go down and you hear the
valve motor wind down. You hear a clunk and a beep
indicating that the valve has received the signal from
the remote control.
Manual ON/OFF Switch: Press the O button.
How to Ensure Your Fireplace Cannot
OWNER’S
INFORMATION
Remote control
handset
Wall Switch
(optional)
Be Turned ON Inadvertently
You can use one of the two following methods to
ensure that your fi replace will not turn on when you
don’t want it on.
First, ensure your fi replace is turned off—including
the pilot—and cold BEFORE going ahead.
• You can prevent your fi replace from lighting by
pressing the O button on the manual ON/OFF switch
on the gas valve—see image above.
• Alternately, remove all batteries from the receiver as
ON
OFF
Manual On/Off Switch
well as the battery from the handset.
Automatic Shut-Off (in certain conditions)
Your fi replace’s remote control is equipped with an
automatic shut-off mechanism which is activated in
certain conditions. See page 14 in the Remote Control
Operation section for a description of this feature.
9
OWNER’S
Current
temperature
(F or C)
Current time
(12 or 24 hour clock)
Modes (Manual,
Temperature, Timer)
Handset
sensor
Battery status
Current
programmed
period (Timer)
Period
start or end
(Temp, Timer)
INFORMATION
Remote Control Operation
NOTE: Before using the remote control system for
the fi rst time, the receiver and the handset must be
synchronized. See the section Remote Control Initial
Set-up on page 28 of this manual.
Display Overview
Note: In the TEMP or TIMER modes, the remote
handset senses the room temperature and adjusts the
fl ame accordingly.
To communicate, the handset should be within 15 feet
(4.5 meters) of the fi replace.
Do not leave the handset on the mantel or hearth.
IMPORTANT: BEFORE YOU BEGIN, please note that
on this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when
the function display is fl ashing. Be patient when
programming as it can take a few seconds to set.
Large ame
Set (scrolls
through
modes and
settings)
OFF (returns
to set mode,
turns the burner
and the pilot o)
Handset Overview
button (ames
up, sets hours,
temperature)
Small ame
button (ames
down and o,
sets minutes,
temperature)
TO TURN ON APPLIANCE TO TURN OFF APPLIANCE
CAUTION
When pilot ignition is confi rmed, motor turns
automatically to maximum fl ame height.
• On the valve, turn MAN knob on the ON, full
counterclockwise position.
• Place ON/OFF switch (if equipped) in I (ON
position).
• Simultaneously press the OFF and
(large fl ame) buttons until a short
beep confi rms the start sequence
has begun; release buttons.
• Continuing beeps confi rm the
ignition is in process.
• Once pilot ignition is confi rmed,
10
there is main gas fl ow.
• After main burner ignition the
handset will automatically go into
manual (MAN) control mode.
• Press OFF button.
When the pilot is off, it will take 2
When the pilot is off, it will take 2
minutes before it can be lit again.
minutes before it can be lit again.
STANDBY MODE (Pilot Flame)
• Press and hold (small fl ame) to set appliance at
pilot fl ame.
FLAME HEIGHT ADJUSTMENT
• In standby mode: Press and hold
(large fl ame) button to increase
fl ame height.
Remote Control Operation
OWNER’S
INFORMATION
• Press and hold (small fl ame)
button to decrease fl ame height or
to set the appliance at pilot fl ame.
• For fi ne adjustment tap the
(large fl ame) or (small fl ame)
buttons.
Express Low and High Fire
• Double-click (small fl ame)
button. “LO” will be displayed.
NOTE: Flame goes to high fi re fi rst
before going to designated low fi re.
x 2
• Double-click (large fl ame)
button. Flame automatically goes
to high fi re. “HI” will be displayed.
x 2
SETTING ºC/24-HOUR OR ºF/12-HOUR CLOCK
• In MAN mode, press OFF and
(small fl ame) buttons until display
changes from Farenheit/12-hour
clock to Celsius/24-hour clock and
vice versa.
SETTING THE TIME
• The time display will fl ash after
either:
• Installing the battery or
• Simultaneously pressing the
(large fl ame) and (small fl ame)
buttons.
• Press (large fl ame) button to
set the hour.
• Press (small fl ame) button to
set the minute.
• Press OFF or simply wait to return
to MAN mode.
MODES OF OPERATION
• Briefl y pressing the SET button
changes the mode of operation in
the following order:
MAN
→ →
TIMER
→ → and back to .
TEMP
NOTE: Manual mode can also be reached by pressing
either the (large fl ame) or the (small
fl ame) buttons.
MAN
• - Manual Mode - Manual
Flame Height Adjustment.
TEMP
• - Daytime Tempera-
ture Mode (Appliance must be in
standby mode; pilot ignited) - The
room temperature is measured and
compared to the set temperature.
The fl ame height is then auto-
matically adjusted to achieve the
Daytime Set Temperature.
TEMP
• - Nighttime Setback
Temperature Mode (Appliance
must be in standby mode; pilot
ignited) - The room temperature
is measured and compared to the
Nighttime Setback temperature.
The fl ame height is then automati-
cally adjusted to achieve the Nighttime Setback Temperature.
TIMER
• - Timer Mode (Appliance
must be in standby mode; pilot
ignited) - The timers P1 and P2
(Program 1, Program 2) each can
be programmed to go ON and OFF
at specifi c times. For instructions
see Timer Programming Mode.
NOTE: The display shows the set temperature every
30 seconds.
TEMP
MAN
11
OWNER’S
INFORMATION
Remote Control Operation
SETTING THE ON / OFF TEMPERATURES
SETTING THE “DAYTIME” TEMPERATURE
Default Settings: (sun), 23ºC / 74ºF
TEMP
SETTING THE “NIGHTTIME SETBACK” TEMPERATURE
Default Settings: (moon), “--” (OFF)
TEMP
• Briefl y press SET button to scroll to
TEMP (sun) mode. Hold
TEMP
the SET button until the TEMP
fl ashes.
• Press (large fl ame) button
to increase the Daytime Set
Temperature.
• Press (small fl ame) button
to decrease Daytime Set
Temperature.
• Briefl y press SET button to scroll to
TEMP (moon) mode. Hold
TEMP
the SET button until the TEMP
fl ashes.
• Press (large fl ame) button to
increase Nighttime Setback
Temperature.
• Press (small fl ame) button to
decrease Nighttime Setback
Temperature.
• Press OFF or simply wait to
complete programming.
12
• Press OFF or simply wait to
complete programming.
Tip
Set the different parameters when they are fl ashing.
Loading...