Vaillant ecoTEC sustain 24, ecoTEC sustain 28, ecoTEC sustain 34, ecoTEC pure VCW 206/7-2, ecoTEC pure VC 146/7-2 Operating Instructions Manual

Operating instructions

ecoTEC sustain

24, 28, 34

GB

Operating instructions

Publisher/manufacturer

Vaillant GmbH

Berghauser Str. 40 D-42859 Remscheid
Tel. [phone]‑0 Fax [phone]‑2810
[e-mail] www.vaillant.de

Contents

2 Operating instructions ecoTEC sustain 0020253095_01

Contents

1 Safety ............................................ 3

1.1 Action-related warnings ................. 3

1.2 Intended use .................................. 3

1.3 General safety information............. 4

2 Notes on the documentation ...... 7

2.1 Observing other applicable

documents ..................................... 7

2.2 Storing documents ......................... 7

2.3 Validity of the instructions .............. 7

3 Product description ..................... 7

3.1 Product design ............................... 7

3.2 Control elements............................ 7

3.3 Description of the display............... 8

3.4 Information on the identification

plate ............................................... 8

3.5 Serial number ................................ 9

3.6 CE label ......................................... 9

3.7 Energy Saving Trust Endorsed

Products......................................... 9

4 Function...................................... 10

4.1 Operating concept ....................... 10

4.2 Opening the isolator devices ....... 11

4.3 Switching on the product ............. 11

4.4 Setting the heating flow

temperature ................................. 11

4.5 Setting the hot water

temperature ................................. 11

4.6 Switching off the product's

functions ...................................... 12

4.7 Guaranteeing the correct filling

pressure in the heating circuit...... 12

4.8 Switching the product to

standby mode .............................. 13

4.9 Protecting the heating

installation against frost ............... 14

5 Troubleshooting ........................ 14

5.1 Detecting and rectifying faults...... 14

5.2 Displaying the status codes......... 14

6 Care and maintenance .............. 14

6.1 Maintenance ................................ 14

6.2 Caring for the product .................. 14

6.3 Reading maintenance

messages .................................... 15

6.4 Checking the condensate drain

pipework and tundish................... 15

7 Decommissioning...................... 15

7.1 Temporarily decommissioning

the product ................................... 15

7.2 Permanently decommissioning

the product ................................... 15

8 Recycling and disposal............. 15

9 Guarantee and customer

service ........................................ 16

9.1 Guarantee.................................... 16

9.2 Customer service ......................... 16

Appendix ............................................... 17

A Operator level – overview ......... 17

B Status codes – Overview........... 17

C Troubleshooting and fault

elimination.................................. 18

C.1 Troubleshooting ........................... 18

C.2 Rectifying faults ........................... 18

Safety 1

0020253095_01 ecoTEC sustain Operating instructions 3

1 Safety

1.1 Action-related warnings
Classification of action-re-

lated warnings

The action-related warnings
are classified in accordance
with the severity of the pos­sible danger using the following
warning signs and signal words:

Warning symbols and signal
words

Danger!

Imminent danger to life
or risk of severe personal
injury

Danger!

Risk of death from electric
shock

Warning.

Risk of minor personal
injury

Caution.

Risk of material or envir­onmental damage

1.2 Intended use

There is a risk of injury or death
to the user or others, or of dam­age to the product and other
property in the event of im­proper use or use for which it
is not intended.

The product is intended as a
heat generator for closed heat-

ing installations and for hot wa­ter generation.

Intended use includes the fol­lowing:

– observance of the operating

instructions included for the
product and any other system
components

– compliance with all inspection

and maintenance conditions
listed in the instructions.

This product can be used by
children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge if
they have been given supervi­sion or instruction concerning
use of the product in a safe way
and understand the hazards in­volved. Children must not play
with the product. Cleaning and
user maintenance work must
not be carried out by children
unless they are supervised.

Any other use that is not spe­cified in these instructions, or
use beyond that specified in this
document shall be considered
improper use. Any direct com­mercial or industrial use is also
deemed to be improper.

Caution.

Improper use of any kind is
prohibited.

1 Safety

4 Operating instructions ecoTEC sustain 0020253095_01

1.3 General safety
information

1.3.1 Danger caused by

improper operation

Improper operation may present
a danger to you and others, and
cause material damage.

▶ Carefully read the enclosed

instructions and all other ap­plicable documents, particu­larly the "Safety" section and
the warnings.

▶ Only carry out the activities

for which instructions are
provided in these operating
instructions.

1.3.2 Risk of death from

escaping gas

What to do if you smell gas in
the building:

▶ Avoid rooms that smell of

gas.

▶ If possible, open doors and

windows fully and ensure
adequate ventilation.

▶ Do not use naked flames (e.g.

lighters, matches).

▶ Do not smoke.
▶ Do not use any electrical

switches, mains plugs, door­bells, telephones or other
communication systems in
the building.

▶ If it is safe to do so, close the

emergency control valve or
the main isolator.

▶ If possible, close the gas isol-

ator cock on the product.

▶ Warn other occupants in the

building by yelling or banging
on doors or walls.

▶ Leave the building immedi-

ately and ensure that others
do not enter the building.

▶ Notify the gas supply com-

pany or the National Grid
[phone] by tele­phone once you are outside
of the building.

1.3.3 Risk of death due to a
blocked or leaking flue
gas pipe

What to do if you smell flue gas
in the property:

▶ Open all accessible doors

and windows fully to provide
ventilation.

▶ Switch off the product.
▶ Inform a competent person.

1.3.4 Risk of death due to
explosive and flammable
materials

▶ Do not use or store explosive

or flammable materials (e.g.
petrol, paper, paint) in the in­stallation room of the product.

Safety 1

0020253095_01 ecoTEC sustain Operating instructions 5

1.3.5 Risk of death due
to changes to the
product or the product
environment

▶ Never remove, bridge or

block the safety devices.

▶ Do not tamper with any of the

safety devices.

▶ Do not damage or remove

any seals on components.

▶ Do not make any changes:

– The product itself
– to the gas, air, water and

electricity supplies

– to the entire flue gas install-

ation

– to the entire condensate

drain system

– to the expansion relief valve
– to the drain pipework
– to constructional condi-

tions that may affect the
operational reliability of the
product

1.3.6 Risk of poisoning
caused by insufficient
supply of combustion air

Conditions: Open-flued opera-

tion

▶ Ensure that there is a suffi-

cient supply of combustion
air.

1.3.7 Risk of corrosion
damage due to
unsuitable combustion
and room air

Sprays, solvents, chlorinated
cleaning agents, paint, adhes­ives, ammonia compounds,
dust or similar substances may
lead to corrosion on the product
and in the air/flue pipe.

▶ Ensure that the supply of

combustion air is always free
of fluorine, chlorine, sulphur,
dust, etc.

▶ Ensure that no chemical sub-

stances are stored at the in­stallation site.

1.3.8 Risk of material damage
caused by frost

▶ Ensure that the heating in-

stallation always remains in
operation during freezing con­ditions and that all rooms are
sufficiently heated.

▶ If you cannot ensure the op-

eration, have a competent
person drain the heating in­stallation.

1 Safety

6 Operating instructions ecoTEC sustain 0020253095_01

1.3.9 Risk of injury and
material damage due to
maintenance and repairs
carried out incorrectly or
not carried out at all

▶ Never attempt to carry out

maintenance work or repairs
on your product yourself.

▶ Faults and damage should

be immediately rectified by a
competent person.

▶ Adhere to the maintenance

intervals specified.

Notes on the documentation 2

0020253095_01 ecoTEC sustain Operating instructions 7

2 Notes on the

documentation

2.1 Observing other applicable
documents

▶ You must observe all operating instruc-

tions enclosed with the system compon­ents.

2.2 Storing documents

▶ Keep this manual and all other applic-

able documents safe for future use.

2.3 Validity of the instructions

These instructions apply only to:

Product article number

ecoTEC
sustain 24

VUW 246/7-2
(H-GB)

0010019980

ecoTEC
sustain 28

VUW 286/7-2
(H-GB)

0010019981

ecoTEC
sustain 34

VUW 346/7-2
(H-GB)

0010019982

Gas Council Numbers

ecoTEC
sustain 24

VUW 246/7-2
(H-GB)

47-044-79

ecoTEC
sustain 28

VUW 286/7-2
(H-GB)

47-044-80

ecoTEC
sustain 34

VUW 346/7-2
(H-GB)

47-044-81

3 Product description

3.1 Product design

3

2

1

1 Product
2 Control elements

3 Plate with serial

number on the
rear

3.2 Control elements

3

4

6

5

7

1 2

1 Display
2 On/off button

and reset button

3 Right selection

button

4

button

5

button

6 Left selection

button

7 Access to the

menu for addi­tional inform­ation/installer
level

3 Product description

8 Operating instructions ecoTEC sustain 0020253095_01

3.3 Description of the display

1

2

3

1 Operating in-

formation

2 Operating mode,

selecting and
confirming the
operating mode

3 Display showing

the current heat­ing flow temper­ature, the filling
pressure in the
heating install­ation, the oper­ating mode or a
fault code

Symbol Meaning

Burner operating correctly

– Burner on

Heating installation filling
pressure

– Permanently on: Filling

pressure in the permitted
range

– Flashing: Filling pres-

sure outside the permitted
range, purging function
activated

DHW mode

– Permanently on: Hot wa-

ter activated

– Flashing: Burner on in

draw-off mode

Heating mode

– Permanently on: Heating

mode activated

– Flashing: Burner on in

heating mode

Maintenance required
Information on maintenance
messages in the event of
faults

Setting to be confirmed

Navigating through various
menus

Symbol Meaning

/ /

Fault in the product

– Appears instead of the

basic display.

S.XX

Status code

OFF – Heating mode is switched

off (summer mode)

– Hot water handling mode

is switched off (product
with integrated hot water
generation)

– Appears when the

product goes into standby
mode.

3.4 Information on the
identification plate

The identification plate is mounted on the
underside of the product in the factory.

The identification plate keeps record of
the country in which the product is to be
installed.

Information
on the identi­fication plate

Meaning

Condensing
technology

Efficiency class of the boiler
in accordance with EC Dir­ective 92/42/EEC

Serial number For quality control purposes;

3rd and 4th digits = year of
production
For quality control purposes;
5th and 6th digits = week of
production
For identification purposes;
7th to 16th digits = product
article number
For quality control purposes;
17th to 20th digits = place of
manufacture

... ecoTEC ... Product designation

Cat. Approved gas category

Type: Xx3(x) Permissible flue gas connec-

tions

2H / 2E / 3P /
2K...

Gas group and gas connec­tion pressure as set at the
factory

Product description 3

0020253095_01 ecoTEC sustain Operating instructions 9

Information
on the identi­fication plate

Meaning

Tmax Max. flow temperature

PMS Maximum water pressure in

heating mode

NOx NOx class for the product

V
Hz

Electric connection

W Max. electrical power con-

sumption

IP Protection class

Code (DSN) Specific product code

Heating mode

Qn Nominal heating load range

in heating mode

Pn Nominal heat output range

in heating mode

Pnc Nominal heat output range

in heating mode (condensing
technology)

Hot water generation

Qnw Nominal heating load range

in hot water handling mode

Pnw Nominal heat output range

in hot water handling mode

D Specific flow rate

PMW Maximum water pressure in

hot water handling mode

Barcode with serial number

GC No. Gas council number

Note

Make absolutely sure that the
product is compatible with the gas
group at the installation site.

3.5 Serial number

The serial number can be found on the
rear of a plastic plate at the bottom of the
front casing and on the identification plate.

3.6 CE label

The CE label shows that the products
comply with the basic requirements of the
applicable directives as stated on the iden­tification plate.

The declaration of conformity can be
viewed at the manufacturer's site.

3.7 Energy Saving Trust Endorsed
Products

Only the most energy efficient products
can carry the ‘Energy Saving Trust En­dorsed Product’ brandmark making it easy
for consumers to choose products that
have met strict energy performance cri­teria.

Available for: Boilers, Heating controls and
chemical inhibitors, the Energy Saving
Trust endorsed product brandmark gives
consumers confidence that a product will
cost less to run, help lower energy bills
and reduce carbon emissions.

About the Energy Saving Trust

Energy Saving Trust is an independent
and impartial organisation that provides
trusted energy saving advice to empower
millions of people to lead affordable, low
energy lifestyles. For more information visit
energysavingtrust.org.uk

4 Function

10 Operating instructions ecoTEC sustain 0020253095_01

4 Function

4.1 Operating concept

The display switches on when you switch
on the product or press a button. You can
now configure settings by pressing the
buttons again.

When you switch the product off using the
on/off button, the display goes out (the
frost protection function is active for as
long as power is supplied).

Button Meaning

– Setting the hot water temperat-

ure

– Cancelling the change to a set

value or activating an operating
mode

– Calling up a higher selection

level in the menu

– Setting the heating flow tem-

perature, filling pressure of the
heating system or activating the
heating mode

– Confirming a set value or activ-

ating an operating mode

– Calling up a lower selection

level in the menu

– Read the system pressure

(press twice)

+

– Calling up the additional func-

tions

or

– Navigating between individual

menu items

– Increasing or decreasing the

chosen set value

– On/off button (press and hold

the button for < 3 s)

– Reset button (press and hold

the button for > 3 s)

Both selection buttons have a soft key
function, i.e. their function can change.

If, for example, you press the left-hand
selection button in the basic display,
the current function switches from (Do­mestic hot water temperature) to (Back).

Adjustable values are always displayed as
flashing.

You must always confirm a change to a
value. Only then is the new setting saved.
You can press to cancel a procedure at
any time. If you do not press any buttons
for longer 15 minutes, the display returns
to the basic display.

4.1.1 Basic display

The basic display shows the current
product status.

To return to the basic display, press the

button. If you do not press any buttons
within three minutes, the display becomes
dark and automatically switches back to
the basic display.

If an error message appears, the error
code will be shown on the basic display.

The available functions vary depending on
whether:

– A room thermostat is connected to the

product or not
– A domestic hot water cylinder with tem-

perature sensor is connected to the

product or not

4.1.2 Operating levels

The product has two operating levels:

– The operator level shows the most im-

portant information and offers set-up

options which do not require any special

prior knowledge.
– Specialised knowledge is required in or-

der to use the installer level (access for

competent persons). This is therefore

protected by an access code.

Function 4

0020253095_01 ecoTEC sustain Operating instructions 11

4.2 Opening the isolator devices

1. Ask the competent person who in­stalled the product to explain to you
where these isolator devices are loc­ated and how to handle them.

2. Open the gas isolator cock installed
on-site.

3. Open the gas isolator cock, which is
directly below the product or in its im­mediate vicinity.

4. Open the service valves in the heating
installation's flow and return.

5. Open the cold water stop valve.

4.3 Switching on the product

1. Only start up the product once the cas­ing has been completely closed.

2. If the display is switched off, press
for less than 3 seconds.

◁ The basic display is shown in the

display.

4.4 Setting the heating flow

temperature

Note

If the eBUS room temperature con­trol is connected to the product,
the domestic hot water temperat­ure and the heating flow temperat­ure cannot be set via the operating
display.

Conditions: The temperature is controlled by the
product

▶ Press .

◁ The heating flow temperature

flashes in the display.

▶ Press the or button to set the tem-

perature.

◁ is shown in the display.

▶ Confirm by pressing .

Note

If you press the button again,
the heating installation pressure
is shown in the display.

▶ Press .

◁ The basic display is shown.

Conditions: Controller-regulated temperature

▶ You cannot set the heating flow tem-

perature.

Note

If you press the button, the
heating installation pressure is
shown in the display.

4.5 Setting the hot water
temperature

Note

If the eBUS room temperature con­trol is connected to the product,
the domestic hot water temperat­ure and the heating flow temperat­ure cannot be set via the operating
display.

4 Function

12 Operating instructions ecoTEC sustain 0020253095_01

Conditions: The temperature is controlled by the
product

▶ Press .

◁ The domestic hot water temperature

now flashes in the display.

▶ Press the or button to set the tem-

perature.

◁ is shown in the display.

▶ Press the button to confirm.
▶ Press .

◁ The display switches to the basic

display.

Conditions: Controller-regulated temperature

▶ Set the hot water temperature on the

controller. See the instructions for the
controller.

4.6 Switching off the product's
functions

4.6.1 Switching off heating mode
(Summer mode)

Conditions: The temperature is controlled by the

product

▶ Press .

◁ The heating flow temperature

flashes in the display.

▶ Press and press and hold until

OFF is shown in the display.

◁ is shown in the display.

▶ Confirm by pressing .

◁ Heating mode is switched off.

▶ Press .

◁ The display switches to the basic

display.

Conditions: Controller-regulated temperature

▶ You cannot switch off heating mode on

the product. See the instructions for the
controller.

4.6.2 Switching off the hot water
handling mode

Conditions: Temperature regulated by the product

or by the room temperature controller

▶ Press .

◁ The domestic hot water temperature

now flashes in the display.

▶ Press and press and hold until

OFF is shown in the display.

◁ is shown in the display.

▶ Press to confirm.

◁ Hot water generation is switched off.

▶ Press .

◁ The display switches to the basic

display.

4.7 Guaranteeing the correct
filling pressure in the heating
circuit

4.7.1 Checking the system pressure

Note

Your product has a pressure
sensor and a digital pressure
indicator.

The product switches to fault mode
if the pressure falls below the re­quired system pressure (below

0.05 MPa (0.5 bar)). If the heating
installation extends over several
floors, a higher system pressure
may be necessary. Ask your com­petent person for details.

1. Press twice.

◁ The current system pressure is

shown in the display.

Function 4

0020253095_01 ecoTEC sustain Operating instructions 13

2. Check the system pressure on the
display.

1 / 2

System pressure: 0.08 … 0.2 MPa
(0.80 … 2.0 bar)
The system pressure is in the intended
pressure range.

2 / 2

System pressure: < 0.08 MPa
(< 0.80 bar)

▶ Fill the heating installation.

(→ Page 13)

◁ When you have reached a suffi-

cient pressure range, the display
disappears after 20 seconds.

4.7.2 Filling the heating installation

Caution.
Risk of material damage due
to heating water that is ex­tremely calciferous or corros­ive or contaminated by chem­icals.

Unsuitable tap water damages
the seals and diaphragms,
blocks components in the
product and heating installation
through which the water flows
and causes noise.

▶ Only fill the heating install-

ation with suitable heating
water.

▶ In case of doubt, ask a com-

petent person for details.

Note

The competent person is respons­ible for filling the heating installa­tion the first time.

1. On-site, connect the filling cock to a
cold water pipe, as explained by the
competent person.

2. Open all radiator valves (thermostatic
radiator valves) of the heating installa­tion.

3. Open the cold water pipe.

4. Turn the filling cock on slowly and al­low water to flow in until the required
system pressure has been reached.

5. Close the cold water pipe.

6. Purge all radiators.

7. Check the system pressure on the
display. (→ Page 12)

8. Top up with more water if required.

9. Close the filling cock.

10. Disconnect the filling cock from the

cold water pipe.

4.8 Switching the product to

standby mode

▶ Press the button for less than three

seconds.

◁ Once the requirement currently in

use has finished, the display will
show OFF and go out.

◁ The product is now in standby mode.
◁ The product's frost protection func-

tion is activated.

◁ The main power supply is not inter-

rupted. The product continues to be
supplied with power.

5 Troubleshooting

14 Operating instructions ecoTEC sustain 0020253095_01

4.9 Protecting the heating
installation against frost

4.9.1 Frost protection function

Caution.
Risk of material damage due
to frost.

The frost protection function
cannot guarantee flow through
the entire heating installation,
which means that parts of the
heating installation may freeze
and therefore become dam­aged.

▶ During a period of frost, en-

sure that the heating installa­tion remains in operation and
that all rooms are sufficiently
heated, even when you are
away.

To keep the frost protection devices active,
you should switch your product on and off
using the controller, if one is provided.

If the heating flow temperature falls be­low 5 °C when the on/off button is on, the
product comes into operation and heats
the circulating water to approx. 30 °C on
both the heating side and the hot water
side (if available).

4.9.2 Draining the heating
installation

When the unit is switched off for an exten­ded period, frost protection can be guar­anteed by completely draining the heating
installation and the product.

▶ Consult a competent person about this.

5 Troubleshooting

5.1 Detecting and rectifying faults

▶ If faults occur or fault messages (F.XX)

are displayed, proceed as set out in the
tables in the appendix.

▶ If the product is not functioning cor-

rectly, contact a competent person.

5.2 Displaying the status codes

1. Press and at the same time.

◁ S.XX is shown in the display, fol-

lowed by the heating flow temper­ature and the internal system pres­sure.

2. Look up the meaning of the status
codes.
Status codes – Overview (→ Page 17)

3. Press .

◁ The display switches to the basic

display.

6 Care and maintenance

6.1 Maintenance

An annual inspection of the product carried
out by a competent person is a prerequis­ite for ensuring that the product is perman­ently ready and safe for operation, reliable,
and has a long working life.

6.2 Caring for the product

Caution.
Risk of material damage
caused by unsuitable clean­ing agents.

▶ Do not use sprays, scouring

agents, detergents, solvents
or cleaning agents that con­tain chlorine.

▶ Clean the casing with a damp cloth and

a little solvent-free soap.

Decommissioning 7

0020253095_01 ecoTEC sustain Operating instructions 15

6.3 Reading maintenance
messages

If the symbol is shown in the display, the
product requires maintenance work.

The product is not in fault mode but contin­ues to operate.

▶ Consult a competent person about this.
▶ If the water pressure is flashing at the

same time, simply add more heating
water.

6.4 Checking the condensate
drain pipework and tundish

The condensate drain pipework and tun­dish must always be penetrable.

▶ Regularly check the condensate drain

pipework and tundish for faults and,
particularly, for blockages.

You must not be able to see or feel any
obstructions in the condensate drain pipe­work and tundish.

▶ If you notice a fault, have it rectified by

a competent person.

7 Decommissioning

7.1 Temporarily decommissioning
the product

Caution.
Risk of material damage due
to frost.

The frost protection and mon­itoring devices are only active
while the unit is connected to
the power mains and switched
on via the on/off button, and
when the gas isolator cock is
open.

▶ Temporarily decommission

the product only if no frost is
expected.

▶ Press the on/off button.

◁ The display goes out.

▶ When decommissioning the product

for a prolonged period (e.g. holiday),
close the gas isolator cock and also, for
combination products, the cold water
stop valve.

7.2 Permanently
decommissioning the product

▶ Have a competent person permanently

decommission the product.

8 Recycling and disposal

▶ The competent person who installed

your product is responsible for the dis­posal of the packaging.

If the product is identified with this

symbol:

▶ In this case, do not dispose of the

product with the household waste.

▶ Instead, hand in the product to a collec-

tion centre for old electrical or electronic
appliances.

If the product contains batteries that
are marked with this symbol, these bat­teries may contain substances that are
hazardous to human health and the envir­onment.

▶ In this case, dispose of the batteries at

a collection point for batteries.

9 Guarantee and customer service

16 Operating instructions ecoTEC sustain 0020253095_01

9 Guarantee and customer

service

9.1 Guarantee

– One year guarantee for ecoTEC sustain

appliances

Vaillant provides this appliance with a
parts and labour guarantee against de­fects that may occur within twelve months
of the installation date.

– Registering with us

Registration is simple. Just complete the
Guarantee Registration Card and return to
Vaillant within 30 days of installation. Your
details will then be automatically registered
within the Vaillant scheme.

– Immediate help

If your Vaillant boiler develops a fault your
first action should be to contact your in­staller, as his professional assessment is
needed under the terms of our Guarantee.
If you are unable to contact your installer,
phone Vaillant Service Solutions:

Telephone: [phone]

9.2 Customer service

To ensure regular servicing, it is strongly
recommended that arrangements are
made for a Maintenance Agreement.
Please contact Vaillant Service Solutions
for further details:

Telephone: [phone]

Appendix

0020253095_01 ecoTEC sustain Operating instructions 17

Appendix
A Operator level – overview

Setting level Values Increment, select, explanation Default set-

ting

Min. Max.

DHW mode

Hot water temperature Current value < 35 = OFF OFF

35 ℃ 60 ℃

Heating mode

Heating flow temperat­ure

Current value < 10 = OFF

Underfloor heating = 35-50
Radiator = 35-80

Note

The temperature range above 75 °C
can only be set by a competent per­son.

OFF

10 ℃ 80 ℃

B Status codes – Overview

Note

Since the code table is used for various products, some codes may not be vis­ible for the product in question.

Codes that are not listed here can be found in the installation instructions.

Status code Meaning

Displays in heating mode

S.00 Heating mode: No requirement

S.02 Heating mode: Pump pre-run

S.03 Heating mode: Burner ignition

S.04 Heating mode: Burner on

S.06 Heating mode: Fan overrun

S.07 Heating mode: Pump overrun

S.08 Heating mode: Temporary shutdown after heating procedure

Displays in hot water handling mode

S.10 Hot water handling mode: Requirement

S.14 DHW mode: Burner on

Display in Comfort mode with warm start or hot water handling mode with cylinder

S.20 Hot water handling mode: Requirement

S.22 Hot water handling mode: Pump pre-run

S.24 DHW mode: Burner on

Other displays

S.31 No heating demand: Summer mode, eBUS controller, waiting period

S.34 Frost protection active

Appendix

18 Operating instructions ecoTEC sustain 0020253095_01

Status code Meaning

S.46 Protection mode: Minimum load

C Troubleshooting and fault elimination

C.1 Troubleshooting

Symptom Possible cause Measure

The system pres­sure is flashing on the
display

The system pressure
is too low: < 0.05 MPa
(< 0.50 bar). Low wa­ter pressure in the
heating installation.

▶ Fill the heating installation. (→ Page 13)

The system pressure
is too high: > 0.3 MPa
(> 3 bar).

▶ Wait until the excess heating water has

flowed out through the expansion relief
valve.

Product does not start
up (no hot water,
heating remains cold)

The gas isolator cock
installed on-site and/or
the gas isolator cock
on the product is
closed.

▶ Open both gas isolator cocks.

The cold water stop
valve is closed.

▶ Open the cold water stop valve.

The product is
switched off.

▶ Switch on the product. (→ Page 11)

The heating flow tem­perature/hot water
temperature has been
set too low and/or the
heating mode/hot wa­ter generation has
been switched off.

1. Set the heating flow temperature.

2. Set the hot water temperature.

There is air in the
heating installation.

▶ Have a competent person purge the heating

installation.

Hot water generation
functioning correctly;
heating does not start
up

The external controller
is not set correctly.

▶ Set the external controller correctly (→Con-

troller operating instructions).

C.2 Rectifying faults

Message Possible cause Measure

F.28 Ignition unsuc­cessful

After three unsuc­cessful ignition at­tempts, the product
has switched to fault
mode.

1. Check whether the gas isolator cock is
open.

2. Press the reset button for longer than
three seconds.

3. If you have been unable to eliminate the
ignition fault after the fault clearance at­tempt, consult a competent person.

0020253095_01 01.03.2017

Supplier

Vaillant Ltd.

Nottingham Road Belper Derbyshire DE56 1JT
Telephone [phone]
[e-mail] www.vaillant.co.uk

© These instructions, or parts thereof, are protected by copyright and may be
reproduced or distributed only with the manufacturer's written consent.

We reserve the right to make technical changes.

0020253095_01