VADDIO WALL VIEW HD-19, 999-6945-001AW, 999-6945-000AW, 999-6945-000, 999-6945-001 Installation And User Manual

A

INSTALLATION AND USER GUIDE

V

AADDDDIIO

V

High Definition PTZ Camera Featuring the Quick-Connect™ SR Interface

Quick-Connect SR Interface

PN: 998-1105-016

O

Black Version
Part Number 999-6945-000 (North America)
Part Number 999-6945-001 (International)

™

™

W

W

L

AALLL

™

™

H

D--1199

H

D

VVIIEEW

rctic White Version
Part Number 999-6945-000AW (North America)
Part Number 999-6945-001AW (International)

W

S

YYSSTTEEM

S

M

©2011 Vaddio - All Rights Reserved ● ClearVIEW HD-19 ● Document Number 342-0266 Rev. A

ClearVIEW HD-19

Inside Front Cover - Blank

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 2 of 20

ClearVIEW HD-19

p

Overview:

The WallVIEW HD-19 HD PTZ camera with Vaddio’s EZCamera™
Cat-5e cabling system using HSDS™, delivers a system that allows
for easy installation and integration of cameras. The HD-19 camera
is built around a 1/3 high-speed, progressive scan CMOS image
sensor with a total of 1.3 Megapixels and a 19X optical zoom lens,
making it the ideal choice for a wide range of high definition video
applications

The HD-19 camera uses an increased pixel aperture size, high
signal to noise and column-parallel A/D conversion method to create
images containing more detail than ever before. It combines the

speed of the CMOS sensor with advanced-quality image sensor
technologies amassed through the development of CCDs. The HD-

19 achieves improved picture quality even in low light environments
requiring a minimum illumination rated at an astonishing 0.7 LUX
(F1.6 - 50IRE).

In the WallVIEW HD-19 System, the HD-19 is paired with the Quick-Connect SR Interface, which provides power
to the camera and returns HSDS video from the camera up to 100’ (30.5m) over a single Cat-5e cable. RS-232
control and IR signals (modulated or non-modulated) can be passed from the camera to third-party equipment,
such as videoconferencing codecs on a second Cat-5e cable. The WallVIEW HD-19 is great for integration
projects since no power supply is required at the camera location.

The WallVIEW HD-19 is available in Black and in Arctic White and is equipped with a slip-clutch mechanism for
smooth pan/tilt operation and control. The HD-19 outputs HD video (YPbPr at 1080p/60/59.94/50/30/25,
1080i/59.94/50, 720p/59.94/50, 480i/30fps and 576i/25fps) and SD video (CVBS at 480i/NTSC or 576i/PAL)
simultaneously. Overall, the HD-19 is an exceptional camera for a wide range of HD video applications such as
houses of worship, videoconferencing, corporate boardrooms, live events and distan ce-learning.

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the
one provided or outdoor operation has not been tested and could damage the device and/or create a potentially
unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermitten t connections which
can result in the RS-232 control line failing and locking up, and/or com promising the HSDS™
signals. For best results please use standard RJ-45 connectors and test all cables for proper

in-outs prior to use and connection to Vaddio product.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 3 of 20

ClearVIEW HD-19

Unpacking:

Carefully remove the device and all of the parts from the packaging.
Unpack and identify the following parts in 999-6945-000:

 One (1) ClearVIEW HD-19 HD Camera
 One (1) Vaddio IR Remote Commander
 One (1) Quick-Connect SR Interface
 One (1) Vaddio PowerRite™ 24 VDC, 2.0 Amp Power Supply
 One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)
 One (1) Thin Profile Wall Mount with Mounting Hardware
 One (1) AC Cord Set for North America
 Documentation

(Note: The 999-6945-001 Int’l Version includes the Euro and UK power cables)

ClearVIEW HD-19 PTZ Camera, Front View with Feature Call-outs:

①

④

②

③

1) Zoom Lens and Image Sensor:

The 19X optical zoom lens is built around a 1/3-Type, high-speed, progressive scan CMOS image sensor with a
total of 1.3 Megapixels for precise HD video image acquisition.

2) Red Tally Light:

A red tally light is illuminated when the camera receives a VISCA command from an external control system.

3) IR Sensors:

IR sensors are built into the front of the ClearVIEW HD-19 to receive IR signals from the IR remote control
supplied with the camera.

4) Blue Power Light:

A Vaddio blue power light is illuminated when the camera is turned on.

Compatible Switchers and Joystick Controllers:

ProductionVIEW™ HD MV

(999-5625-000)

AutoPresenter

(999-5675-000)

Precision Camera Controller

(999-5700-000)

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 4 of 20

ClearVIEW HD-19

ClearVIEW HD-19 PTZ Camera, Rear View with Feature Call-outs:

⑤

⑨

⑥

⑩

⑦

⑪

⑧

⑫

5) RS-232 IN & IR Out:

The RS-232 accepts modified VISCA protocol for camera control, as well as transmits IR signaling received by
the IR receivers, which can be transmitted to third party devices.

6) Dip Switch Settings:

Settings for IR remote, baud rate, SD output format, and image flip can be configured on these switches. See
page 5 for additional information on switch settings.

7) HD Video Select:

A rotary switch allows the user to choose the component HD output video resolution and format. See page 6 for
additional information on switch settings.

8) 12 VDC Input:

Power input for the standard, ClearVIEW HD-19 camera power supply.

9) YPbPr Output:

Component HD video is fed through the DB-15 connector. YPbPr and Composite signals are simultaneous. This
is an HD camera and the SD signals are down converted and are really not the sweet spot of this camera.

9) Composite Video (CVBS) Output:
The CVBS output feeds out SD video signals and is configurable with the dip switches to choose between
480i/NTSC or 576i/PAL in 4:3 formats. Squeeze and letterbox modes are also available (see dipswitches 6&7).

11) EZ Power/Video Port:

This RJ-45 connector is only used with the Quick-Connect SR Interface and the Quick- Connect DVI-D/HDMI SR
Interface to supply power and return HSDS video from the camera.

12) Slot for Optional Cards:

Optional slot cards can be plugged into the ClearVIEW HD-19 camera (the HD-SDI and the EZIM CCU Slot Cards
are available).

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 5 of 20

ClearVIEW HD-19

Quick-Connect SR Interface Rear Panel with Feature Call-outs:

1) Power Input:

5.5mm OD x 2.5mm ID coaxial connector for the provided PowerRite 24 VDC, 2.0 Amp power supply.

2) EZCamera Power & HD Video:

A single Cat-5e connection between the EZCamera Power & HD Video RJ-45 connector and the EZ Power HD
Video Port on the HD-19 camera extends power and video up to 100’ (30.5 m). Power is fed to the camera and
HSDS video is returned on the Cat-5e.

3) HD Video Output:
DE-15 connector outputs the YPbPr analog component HD video extended from the camera over Cat-5e cable.
SD video resolutions are not supported by the HD-19 Camera or the Quick-Connect SR Interface.

4) IR Output:

With the IR pass-thru turned on at the camera (see Camera Settings section), send IR from third-party IR remote
controls to third-party equipment, such as videoconferencing codecs. IR can be transmitted as either modulated
or non-modulated signals for added flexibility.

5) RS-232 Input & Output Jacks:
When using the IR pass-thru function, the IR signals are pulled from the Cat-5e RS-232 cable and delivered as
modulated and non-modulated signals to the IR Output ports.

INSTALLATION (Making things easier):

The WallVIEW HD-19 product was specifically designed for installation on a vertical wall surface with Cat-5e
cable connectivity for Power, Video and Control signaling (two cables are required). Installation is simplified in
that no custom 8-Pin mini-din cables or expensive coax plenum cables are needed and no power outlets are
required near the camera bracket. All cabling is routed to the head-end using Cat-5e cables.

Before Installing:

 Locate the camera mounting location paying close attention to camera viewing angles, lighting conditions,

possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted.
Pick a mounting location that will optimize the performance of the camera.

 The Thin Profile Wall Mount for the WallVIEW HD-19 can be mounted directly to a 2-gang wall box or can be

mounted to the drywall using four dry wall anchors.

RS-232 Cabling:
For RS-232, use a standard Cat-5e cable and RJ-45 connectors (568B termination) from the RS-232 port on the
back of a Vaddio camera controller or switcher. If the camera is connected to a third-party control system (such
as AMX or Crestron), a DB-9 to RJ-45 control adapter cable is supplied. Use of pass-thru type RJ-45

connectors is highly discouraged. The Vaddio Cat-5e wiring standard uses pins 7 and 8 on both the
video and the control Cat-5e cables. The pass-through connectors have proven to provide insufficient
connectivity for these important signals. They are “ok” for voice and data, but not for video and control.

①

② ④

③

⑤

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 6 of 20

ClearVIEW HD-19

First Time Set-up with the HD-19:

The ClearVIEW HD-19 was designed to be exceptionally easy to use and operate. There is documentation at the
back of the manual for pin-outs for all of the connectors on the ClearVIEW HD-19 camera.

Step 1: Using the HD Video Select Rotary Switch and Camera Settings Dip Switch on the back of the camera,
set up the camera’s output resolution and functional preferences. There is a label on the bottom of the camera
that identifies the choices.

HD Video Select Switch Camera Settings 10-Pos Dip Switch

HD-19
Rear
Panel

Label on the Bottom of HD-19

IR 1

1 & 2 UP

IR 2ONIR 3

ON

21

1234

DIP SWITCH SETTINGS

IR
OUT
OFF

ON

3

9600

bps

38400

bps

4

SD

NTSC

SD

PAL

5

56

IMAGE

SD 4:3

SD
LB

7

7

FLIP
OFF

ON ON

8

6 & 7 UP

SD

SQ

68109

TEST

10

BARS

OFF

OFF

ON

910

0
1
2
3
4
5
6
7

HD VIDEO SELECT

720p/59.94

1080i/59.94

1080p/59.94

1080p/60

720p/50

1080i/50

1080p/50

480i/29.97

576i/25

8
9
A
B
C
D

1080p/30

E

1080p/25

F

 Set the HD output resolution for the camera with the Rotary Switch.
 Set the IR frequency of the camera if it is to respond to the IR remote control.
 If using RS-232 for control, leave the IR OUT OFF (SW3) and choose 9600bps for most applications.
 If using the IR forwarding feature, turn the IR OUT ON (SW3).
 If inverting the camera, turn the IMAGE FLIP ON (SW8).

Dip Switch Settings:
IR 1 & 2: The IR remote has the capability of operating up to three different PTZ cameras from one remote. Use
the selector buttons at the top of the IR remote to select the frequency.
IR Out 3: The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on the IR

output will allow IR signals to be transmitted over the CAT-5 cable to the head end. When using RS-232 control
or Vaddio CCU controllers (also via RS-232), turn the IR OUT to OFF.

Baud Rate 4: The options for baud rate are either 9600 bps or 38,400 bps. Default is 9600 bps.
SD Format 5: Choose between NTSC or PAL formats
SD Configurations 6 & 7: SD video can be set to standard 4:3, squeeze mode or letterbox mode.
Image Flip 8: To invert the HD-19, turn the IMAGE FLIP ON (switch down).
Test Bars 9: Turning on the non-standard test bars will override the camera video output. These non-standard

test bars are 75% IRE.
Switch 10: Leave up - or in the OFF position

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 7 of 20

ClearVIEW HD-19

Basic Wiring Configuration of the WallVIEW HD-19 to a Vaddio Joystick Controller

Rear
Panel
HD-19

RS-232
Cat-5e

24VDC, 2.0 A

PowerRite Power

Supply

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 8 of 20

YPbPr & Power on one (1) Cat-5e up to 100’ (30.5m)

← YPbPr (HSDS differential)

→

Power

YPbPr

HD Monitor

(Really Simulated Feed)

ProductionVIEW Precision Camera Controller

Rear Panel
Quick-Connect SR Interface
(Equipment Head-end)

ClearVIEW HD-19

Videoconferencing System Configuration: Includes the HD-19, Quick Connect SR Interface with the IR
forwarding feature allowing communication to the Polycom® HDX codec with HD-19 as the main camera.

IR Remote for
HDX Codec

HD-19 Camera with IR
Forwarding on - used as
Main Camera for HDX
Codec

YPbPr & Power
on one (1) Cat-5e
up to 100’ (30.5m)

← YPbPr (HSDS differential)

→

Power

RS-232 and IR Return
One (1) Cat-5e Cable

Two (2) Cat-5e Cables
up to 100’ (30.5m)

Quick-Connect SR

RS-232

Polycom HDCI
Break-out Cable
(Sourced from
Polycom)

Polycom HDX

Control
Adapter

Non-modulated
IR - To IR input
on Spring Cage
Connector

Far End Near End

HD VIDEO

(Simulated Video Feeds)

Videoconferencing Codecs, RS-232 and IR Forwarding:

In the case above, the codec is directly controlling the HD-19 camera and the HD-19 is receiving the IR from the
Polycom IR Remote and forwarding it to the codec to allow complete functionality of both the codec and remote
while using the HD-19 as the main camera. Depending on the codec that is used, special DB-9 to RJ-45 adapters
may sometimes be required. Refer to Vaddio’s website, price list for adapter functions and part numbers.

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 9 of 20

ClearVIEW HD-19

BASIC INSTALLATION INSTRUCTIONS
Step 1: After determining the optimum location of the camera system, route, mark

and test the two (2) Cat-5e cables from the camera to the Quick-Connect SR
Interface located at the head-end. The two Cat-5e cables should feed-through the
oval slot located on the rear flange of the wall mount. If the bracket is to be

Thin Profile

Camera

Mount

mounted on a 2-gang wall box, use the screws supplied with the wall box cover
plate to attach the Thin Profile Wall Mount. If mounting to the drywall with wall
anchors, use four (4) quality wall anchors. The mounting holes are slotted and are
90° opposing to provide easy leveling. Level the mount and tighten the mounting
screws.

Step 2:

Follow the sample wiring diagram on the previous pages for connecting the Cat-5e cables to the camera and
Quick-Connect SR Interface. Additional diagrams are available on our website for installation with a variety of
videoconferencing codecs.

NOTE: Check all Cat-5e cables for continuity in advance of the final connection. Label the
Cat-5e cables. Plugging the EZ POWER HD VIDEO cable into the w rong RJ-45 may cause
damage to the camera system and void the warranty.

Step 3: Place the camera onto the camera mount and use the ¼”-20 screws to secure the camera to the mount.
Step 4: Connect the Vaddio 24 VDC power supply to an AC outlet and to the Quick Connect SR Interface.

Power will travel down the Power/Video Cat. 5 cable to the camera. The camera will “Home” to a centered
position ready for control information from the IR remote control or RS-232 camera controller of the integrators’
choice. To insure proper continuity of control and operation of the cameras, the RS-232 controller (control system
or joystick) should be powered on after the camera.

General Specifications:

WallVIEW HD-19 High Definition PTZ Camera System

Part Numbers WallVIEW HD-19 North America 999-6945-000 (Black), 999-6945-000AW (Arctic White)

Image Sensor 1/3-Type Exmor High-speed, Progressive Scan CMOS Sensor with 1.3 Megapixels
Video Output Resolutions

Lens/ Focal Length 19X Optical Zoom, F=4.5mm wide to 85mm tele end (F1.6-F2.9), Min. Focus Distance 1.0m
Horizontal Viewing Angle 58.1° Wide End to 3.2° Tele End - 16:9 Format
Video S/N Ratio >52 dB
Minimum Illumination 0.7 LUX (F1.6, 50IRE)
Serial Control Protocol RS-232 (Modified VISCA)
Pan Range Pan: +170 degrees to -170 degrees, Tilt: +90 degrees to -30 degrees, Invertible for Ceiling Mount
Preset Positions 16 (internal), 6 recalled via IR Remote
Tally Light Available through RS-232 Control
Connectors

HD Video Select 16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings 10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip, SD LB and SQ, Test Bars

Accessories Thin Profile Wall Mount 535-2000-230 (Black), 535-2000-230W (White)

General Information

Operating Temperature 32° to 104° F (0° to 40° C) / 20% to 80% Relative Humidity
Dimensions (H x W x D) 8.5” (215.9mm) H x 6.75” (171.45mm) W x 7.7” (195.58mm) D
Weight 5.79 lbs. (2.625635463kg.)

WallVIEW HD-19 International 999-6945-001(Black), 999-6945-001AW (Arctic White)

HD: 1080p/60/59.94/50/30/25, 1080i/59.94/50, 720p/59.94/50
SD: 480i/NTSC & 576i/PAL (Crop, Squeeze or Letterbox mode)

 12 VDC Power Input: EIAJ-04 Coaxial Power Connector
 HD Video Outputs: YPbPr on DE-15 (D-Sub 15-pin HD)
 SD Video Output: BNC Connector
 RS-232/IR Out: RJ-45 Jack (RS-232 Communication and IR Out (with Quick-Connect -SR

Interfaces)

 EZ Power HD Video: RJ-45 Jack, for use with Quick-Connect SR Interface or Quick-Connect

DVI/HDMI SR Interface. Supplies power to the camera and returns HD video from the camera to the
Quick-Connect - SR Systems.

OSD (On Screen Display) for fine tuning

EZIM HD-SDI Slot Card PN# 998-6900-007
EZIM CCU Slot Card PN# 999-6900-006 - For Use with Quick-Connect CCU Only

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 10 of 20

ClearVIEW HD-19

Compliance and CE Declaration of Conformity - ClearVIEW HD-19

Compliance testing was performed to the following regulations:

 FCC Part 15, Subpart B Class A
 ICES-003, Issue 4: 2004 Class A
 EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005) Class A
 AS/NZS CISPR 22: 2009 + A1: 2010 Class A
 VCCI V-3/2010.04 Class A
 EMC Directive 2004/108/EC Class A

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions a nd
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:

EMC Directive 2004/108/EC
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 Immunity

 EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
 EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
 EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
 EN 61000-4-5: 2006 Surge Immunity
 EN 61000-4-6: 2009 Conducted Immunity
 EN 61000-4-8: 2010 Power Frequency Magnetic Field
 EN 61000-4-11: Second Edition: 2004 Voltage Dips, Interrupts and Fluctuations

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 11 of 20

ClearVIEW HD-19

Warranty Information:

(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):
Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against d efects in materials and

workmanship for a period of one year from t he day of purchase from Va ddio. If Vaddio receives notice of such defects during
the warranty period, they will, at their option, repair or replace products that prove to be defective. Please see Vaddio’s
Service Terms and Conditions at vaddio.com for specific details and policies.

Exclusions: The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by the
customer, customer applied software or interfacing, unauthorized modifications or misuse, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, improper extensio n of the power supply cable
or improper site operation and maintenance.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or pro ducts without charge if the unit is under
warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. T he
cost of parts and labor charge will be estimated by a tech nician an d confirmed by the customer prior to repair. All components
must be returned for testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs
and/or replacement. Vaddio Technical Support can be contacted through one of the follo wing resources: e-mail support at

[e-mail] or online at www.vaddio.com.

Return Material Authorization (RMA) Number: Before returning a product for repair or replacement, request an RMA from
Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping address, and product
serial numbers and describe the reason for repairs or retur ns as well as the date of purchase and proof of purchase. Include
your assigned RMA number in all correspon dence with Vaddio. Wr ite your assigned RMA number on the outside of the box
when returning the product. All products returned for credit are subject to a restocking charge without exception.

Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, or unauthoriz ed repai r. Cutting the po wer supply cabl e on
the secondary side (low voltage side) to extend the power to the device (camera or controller) voids the warr anty for that
device.

Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but wi ll not assume responsibility for loss and/or damage by the outbound
freight carrier.

• If the return shipment appears damaged, retain the original boxes and p acking mater ial for inspectio n by the carrier. Contac t
your carrier immediately.

Products Not Under Warranty: Payment arrangements are required before outbound shipment for all out of warranty
products.

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.

Other General Information:
Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

 Do not spill liquids in the product
 Keep this device away from food and liquid
 For smears or smudges on the product, wipe with a clean, soft cloth
 Use a lens cleaner on the lens
 Do not use any abrasive chemicals.

Operating and Storage Conditions:

Do not store or operate the device under the following conditions:

 Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
 High humi dit y, condensing or wet environments
 In inclement weather
 In swimming pools, bear caves or in a station wagon
 Dry environments with an excess of static discharge
 In outer space (typical)
 Under severe vibration

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 12 of 20

ClearVIEW HD-19

Appendix 1: YPbPr Video Pin-Out for the HD-19 Camera and Quick-Connect SR Interface

Pin YPbPr

1 Pr
2 Y
3 Pb
4 ­5 ­6 Pr GND
7 Y GND
8 Pb GND

9 ­10 ­11 ­12 ­13 ­14 ­15 -

EZCamera Power & HD Video RJ-45 Connector Pin-outs

The EZCamera Power and HD Video RJ-45 Connector is for use with either the Quick-Connect SR
Interface or the Quick-Connect DVI/HDMI SR Interface ONLY (568B Wiring Standard). The video
signals are differential (HSDS™) and can only be received by the interfaces above.

Pin YPbPr

1 Power+

2 Power-

3 Y+

4 PB+

5 PB GND

6 Y GND

7 PR+

8 PR-

Appendix 2: ClearVIEW HD-19 Dimensions

12345678

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 13 of 20

ClearVIEW HD-19

Appendix 3: Communication Specification
Communication Speed: 9600 bps (default)

Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control

12345678

Pin # RJ-45 RS-232 and IR Out Pins

1) Unused

2) Unused

3) Unused

4) IR Output (Diff Signal to Quick-Connect SR)

5) IR Ground (Diff Signal to Quick-Connect SR)

6) GND (GND of IR Short Range - Pin 3)

7) RXD (from TXD of control source)

8) TXD (to RXD of control source)

NOTE: The Vaddio ClearVIEW HD-19 Control Protocol is similar, but not identical to the Sony® VISCA™
command set in order to be compatible with several popular control devices. Not all VISCA commands are
supported and there are many HD-19 specific commands in the following Command and Inquiry Lists.

HD-19 Command List (1/2)

Command Set Command Command Packet Comments

Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On

Off(Standby)

CAM_Zoom Stop

Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Direct(Variable)

CAM_Focus Stop

Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct

CAM_WB Auto

Manual
One Push WB

CAM_RGain Reset

Up
Down
Direct

CAM_BGain Reset

Up
Down
Direct

CAM_AE Full Auto

Manual
Shutter Priority
Iris Priority

CAM_Iris Reset

Up
Down
Direct

CAM_Gain Reset

Up
Down
Direct

CAM_Bright Reset

Up
Down
Direct

8x 01 04 00 02 FF
8x 01 04 00 03 FF
8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 0p 0q 0r 0s FF
8x 01 7E 01 4A 0v 0p 0q 0r 0s FF
8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF
8x 01 04 35 00 FF
8x 01 04 35 05 FF
8x 01 04 35 03 FF
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 00 00 0p 0q FF
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 00 00 0p 0q FF
8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 39 0A FF
8x 01 04 39 0B FF
8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF
8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF
8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF

Power On/Off

pqrs: Zoom Position*
v:(Speed) 0-7

pqrs: Focus position*

pq:00-ff

pq:00-ff
Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode (default)

pq(0x00-0x11)

pq(0x00-0x24)

pq(0x01-0x64)

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 14 of 20

ClearVIEW HD-19

HD-19 Command List (2/2)

Command Set Command Command Packet Comments

CAM_Backlight On
CAM_Aperture Reset

CAM_Memory Reset

CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFF F
IR_Receive On

Pan-tiltDrive Up

Tally On
Preset Pan Speed Pan/Tilt/Zoom Speed 81 01 7E 01 0B WW SS ZZ FF WW: Pan Speed (0x01-0x18)

Motor Config Hard Motor Stops
BLK.Enhance Pedestal No Support No Support

GMA.Enhance Gamma 8x 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance Chroma 8x 01 7E 55 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance Knee No Support No Support
DIS.Enhance Digital Image

SNR.Enhance Super Noise
AGC.Enhance AGC Mode 8x 01 7E 59 00 FF

CAM_Shutter Reset

CAM_ExpComp On

CAM_ICR
Cut Filter

Off
Up

Down
Direct

Set
Recall

Off
On/Off

Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
Absolute Position

Home
Reset

Off

Soft Motor Stops

Stabilizer
Reduction

Up
Down
Direct

Off
Reset
Up
Down
Direct
ICR On
ICR Off

8x 01 04 33 02 FF
8x 01 04 33 03 FF
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF
8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x01 04 3F 02 0p FF

8x 01 06 08 02 FF
8x 01 06 08 03 FF
8x 01 06 08 10 FF
8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
81 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 04 FF
81 01 06 05 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF

8x 01 7E 01 70 00 00 FF
8x 01 7E 01 70 00 01 FF

8x 01 7E 57 02 FF
8x 01 7E 57 03 FF
8x 01 7E 58 02 FF
8x 01 7E 58 03 FF

8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF
8x 01 04 0A 00 FF
8x 01 04 0A 02 FF
8x 01 04 0A 03 FF
8x 01 04 4A 00 00 0p 0q FF
8x 01 04 3E 02 FF
8x 01 04 3E 03 FF
8x 01 04 0E 00 FF
8x 01 04 0E02 FF
8x 01 04 0E 03 FF
8x 01 04 4E 00 00 0p 0q FF
8x 01 04 01 02 FF
8x 01 04 01 03 FF

pq(0x00-0x1F)

p:Memory No(=0-0xe)

IR forwarding/Local IR
WW: Pan Speed (0x01-0x18)
VV:Tilt Speed(0x01-0x14)

YYYY: Pan Position**
ZZZZ: Tilt Position**

SS:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);

On
Off
On
Off
Off
Low
Medium
High

pq(0x00-0x23)
AutoExposure Off
AutoExpouse On

Pq: 0x00-0x24
ICR On - Cut Filter Out
ICR Off - Cut Filter In

*Zoom and Focus Data:

CAM_Zoom: Range(0x000–0x6B3)
CAM_Focus: Range (0x000-0xC000) dependent on Zoom Position

**Additional Information:

Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)

Actual Pan/Tilt ranges defined in Inquiry list

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 15 of 20

ClearVIEW HD-19

HD-19 Inquiry List (1/1)

Inquiry Command Command Response Packet Comments

CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF

y0 50 03 FF
CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: 0-0x6B3
CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position
CAM_WBModeInq 81 09 04 35 FF y0 50 00 FF

y0 50 05 FF

y0 50 03 FF
CAM_RGain 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq:000-0ff
CAM_BGain 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq:000-0ff
CAM_Iris 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq(0x00-0x11)
CAM_Gain 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x24)
CAM_Bright 8x 01 04 4D FF y0 50 00 00 0p 0q FF pq(0x01-0x64)
CAM_BacklightModeInq 8x 09 04 33 FF y0 50 02 FF

y0 50 03 FF
CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF Pq:x00-0x1F
CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FF p:Preset 0-0xf
CAM_IDInq 8x 09 04 3F FF y0 50 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_ReceiveInq 8x 09 06 08 FF y0 50 02 FF

y0 50 03 FF
Pan-TiltMaxSpeedInq 8x 09 06 11 FF y0 50 pp qq FF pp:Pan 0x01-0x18

Pan-tiltPositionInq 8x 09 06 12 FF FF y0 50 0p 0p 0p 0p 0q 0q 0q 0q FF pppp: Pan 0x8044-0x7FB2
TallyInq 8x 09 7E 01 0A FF y0 50 02 FF

y0 50 03 FF
PresetSpeedInq 8x 09 7E 01 0B FF y0 50 pp qq rr FF pp:Pan 0x01-0x18

Motor Config 8x 09 7E 01 70 FF y0 50 00 FF

y0 50 01 FF
BLK.Enhance No support No Support Pedestal
GMA.Enhance 8x 09 7E 54 FF y0 50 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance 8x 09 7E 55 FF y0 50 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance No support No Support Knee
DIS.Enhance 8x 09 7E 57 FF y0 50 02 FF

y0 50 03 FF
SNR.Enhance 8x 09 7E 58 FF y0 50 02 FF

y0 50 03 FF
AGC.Enhance 8x 09 7e 59 FF y0 50 00 FF

y0 50 01 FF

y0 50 02 FF

y0 50 03 FF

y0 50 04 FF
CAM_AEModeInq 8x 09 04 39 FF y0 50 00 FF

y0 50 03 FF

y0 50 0A FF

y0 50 0B FF
CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq: 0x0-0x23
CAM_ExpCompModeInq 8x 09 04 3E FF y0 50 02 FF

y0 50 03 FF
CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Pos
CAM_ICRModeInq 8x 09 04 01 FF y0 50 02 FF

y0 50 03 FF

On
Off(Standby)

Auto
Manual
One Push WB

On
Off

On
Off

qq:Tilt 0x01-0x14
qqqq: Tilt 0xE890-0x4C2C

On
Off

qq:Tilt 0x01-0x14
rr:Zoom 0x00-0x07
Hard Motor Stops
Soft Motor Stops

On
Off
On
Off
Off
Low
Medium
High
Manual AGC
Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode

On - AE Mode Off
Off – AE Mode On

On - ICR filter Out
Off – ICR filter In

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 16 of 20

ClearVIEW HD-19

Appendix 3 (continued):
Iris Position:

Index F-Stop (Iris Position)

0x11 F1.6
0x10 F2.0
0x0F F2.4
0x0E F2.8
0x0D F3.4
0x0C F4.0
0x0B F4.8
0x0A F5.6
0x09 F6.8
0x08 F8.0
0x07 F9.6
0x06 F11.0
0x05 F14.0
0x04 F16.0
0x03 F19.0
0x02 F22.0
0x01 F28.0
0x00 Close

Gamma Position:

Index Gamma value

0x10 1.00
0xF 0.95
0xE 0.90
0xD 0.85
0xC 0.80
0xB 0.75
0xA 0.70
0x9 0.65
0x8 0.60
0x7 0.55
0x6 0.50
0x5 0.45
0x4 0.40
0x3 0.35 (Default)
0x2 0.30
0x1 0.25
0x0 0.20

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 17 of 20

ClearVIEW HD-19

Appendix 3 (continued):
Shutter Position (Speed):

Index Shutter (Speed)

0x23 1/30000
0x22 1/10000
0x21 1/5000
0x20 1/2500
0x1F 1/1500
0x1E 1/1000
0x1D 1/700
0x1C 1/600
0x1B 1/500
0x1A 1/480
0x19 1/360
0x18 1/300
0x17 1/250
0x16 1/240
0x15 1/200
0x14 1/180
0x13 1/150
0x12 1/120
0x11 1/100
0x10 1/60
0x0F 1/50
0x0E 1/30
0x0D x2
0x0C x4
0x0B x6
0x0A x8
0x09 x10
0x08 x12
0x07 x14
0x06 x16
0x05 x20
0x04 x24
0x03 x32
0x02 x40
0x01 x48
0x00 x60

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 18 of 20

ClearVIEW HD-19

Inside Back Cover - Blank

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 19 of 20

ClearVIEW HD-19

©2011 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to
change without notice. Vaddio, ProductionVIEW, ClearVIEW, Quick-Connect, EZCamera, AutoPresenter, HSDS and PowerRite are registered trademarks of
Vaddio. All other trademarks are property of their respective owners. Document Number 342-0266 Rev A.

Toll Free: 800-572-2011 ▪ Phone: [phone] ▪ FAX: [phone]

9433 Science Center Drive, Minneapolis, MN 55428

www.vaddio.com

ClearVIEW HD-19 Manual 342-0266 Rev. A Page 20 of 20