Vaddio DomeVIEW Outdoor Pendant Mount User Manual

Camera and Electronic Products for Integrators

Installation and User Guide

OOMME

VVIIEEW

™

Integrated Outdoor Environmental Pendant Mount Dome Systems and Outdoor Pendant Mount Dome Enclosures for Sony® and Canon® PTZ Cameras

OVERVIEW:

The Vaddio™ DomeVIEW Outdoor, Environmental Pendant Mount Domes (Figure 1) are integrated camera mounting systems that are attractive and easy to install. Designed for outdoor security applications, and including an internal heater/blower, the 8.2” (20.8cm) Outdoor Pendant mount dome enclosure is outfitted with the internal brackets to support the option of using the Sony EVID70 or the Canon VC-C50iR robotic PTZ cameras.

The DomeVIEW Outdoor Pendant Mount Dome Package is sold complete with the Camera. The DomeVIEW system for the Sony EVI-D70 and VC-C50iR features the standard Vaddio EZCamera Cabling System. The EZCamera cabling solution provides for fast and efficient installations using Cat. 5 cabling for video, power and control. The enclosures are also sold without the camera to accommodate an existing camera to be used with the Outdoor Pendant Mount Dome enclosure without the EZCamera cabling system.

The outdoor domes are formed from optical grade polycarbonate and are available in smoked tint (clear is optional). The DomeVIEW Outdoor Pendant Mount Domes are excellent values that are high quality, attractive and durable solutions for outdoor security applications.

Figure 1:

Outdoor Pendant Mount Dome shown with Smoke Tinted Dome standard (Clear is an option)

This Manual covers the following Vaddio DomeVIEW Outdoor Pendant Mount Dome Systems:

 999-9200-050 DomeVIEW 50iR Outdoor Pendant Dome with Canon VC-C50iR, EZCamera Cabling

System and Internal Mounting Bracket

 999-9200-070 DomeVIEW 70 Outdoor Pendant Dome with Sony EVI-D70, EZCamera Cabling System

and Internal Mounting Bracket

This Manual covers the following Outdoor Pendant Mount Dome Enclosures:

 998-9200-050 Outdoor Pendant with Internal Mounting Bracket for VC-C50iR (Camera Not Included)  998-9200-070 Outdoor Pendant with Internal Mounting Bracket for EVI-D70 (Camera Not Included)

Note: The Outdoor Pendant Mount Domes mount to a 1-1/2” NPT Pipe, which are not part of the DomeVIEW packages or the Outdoor Pendant Mount Dome enclosures.

INTENDED USE:

Before operating the DomeVIEW system, please read the entire manual thoroughly. The DomeVIEW Outdoor Pendant Mount systems were designed, built and tested for use Outdoors (or indoors) and with the provided power supply. The use of a power supply other than the one provided or has not been tested and could damage the electronics and/or create a potentially unsafe operating condition.

SAVE THESE INSTRUCTIONS:

The information contained in this manual will help you install and operate your Vaddio DomeVIEW. If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on

the website. These documents can be downloaded from www.vaddio.com

free of charge.

IMPORTANT SAFEGUARDS:

Read and understand all instructions before using. Do not operate the system if it has been dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

ⓒ2009 Vaddio - DomeVIEW Systems - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are subject to change without notice. Vaddio, DomeVIEW, EZCamera, Quick-Connect, WallVIEW, CeilingVIEW, EZCable and PowerRite are

trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Document 341-445 Rev C.

Use only the power supply (or power supplies) provided with the DomeVIEW systems. Use of any unauthorized power supply will void any and all warranties.

Do not use “pass-thru” RJ-45 connectors during installation. Use only standard RJ-45 connectors and test all terminated cables.

UNPACKAGING – SYSTEM COMPONENT LISTS

Carefully remove all parts from the packaging. Unpack and identify the following parts for each product:

999-9200-050 DomeVIEW 50iR Outdoor Pendant Mount Dome System includes:

QTY Description

1 Canon VC-C50iR PTZ camera 1 Canon IR remote control

- Camera bracket for Canon VC-C50iR PTZ camera 3 2” x .375 (50.8mm x 9.525mm) ¼”M to 8-32F Hex shaped stand-offs 1 6.25” x 5.25” (15.87cm x 13.34cm) Camera mounting stage 2 8-32 x .5” Flat head screws (flush mount) 2 8-32 x .5” pan head screws 2 #8 Lock washers for pan head screws

- Outdoor Pendant Mount Dome Enclosure 1 Outdoor Pendant Housing Assembly (white outer shell, black inner shell, safety tethers) 1 Heater/blower fan assembly, mounting platform secured with three 10-32 x .5” flat head screws 1 8.2” (20.8cm) Smoke tinted dome bubble with four (4) attached stainless steel mounting screws 1 1-1/2” NPT Locknut 1 Foam dust plug for 1-1/2” NPT pipe fitting 1 Tube of pipe sealer and proprietary Allen wrench (do not lose this wrench)

- EZCamera Cabling Components 1

999-9200-070 DomeVIEW 70 Outdoor Pendant Mount Dome System includes:

QTY Description

1 Sony EVI-D70C/W PTZ camera (platinum white) 1 Vaddio IR Remote Commander (for Sony cameras)

- Camera bracket for Sony EVI-D70 PTZ camera 3 1.125” x .375 (28.58mm x 9.525mm) ¼”M to 8-32F Hex shaped stand-offs 1 6.25” x 5.25” (15.87cm x 13.34cm) Camera mounting stage 2 8-32 x .5” Flat head screws (flush mount) 1 6.25” x 5.25” (15.87cm x 13.34cm) Camera mounting plate 1 ¼”-20 x ½” Mounting screw (to attach camera to mounting plate) 2 8-32 x .5” pan head screws 2 #8 Lock washers for pan head screws

- Outdoor Pendant Mount Dome Enclosure 1 Outdoor Pendant Housing Assembly (white outer shell, black inner shell, safety tethers)

1 Heater/blower fan assembly, mounting platform secured with three 10-32 x .5” flat head screws 1 8.2” (20.8cm) Smoke tinted dome bubble with four (4) attached stainless steel mounting screws 1 1-1/2” NPT Locknut 1 Foam dust plug for 1-1/2” NPT pipe fitting 1 Tube of pipe sealer and proprietary Allen wrench (do not lose this wrench)

- Vaddio EZCamera Cabling Components 1 EZCamera Cabling Shoe (998-2211-004) 1

1 PowerRite Power Supply (451-2750-018) and separate 24 VAC Power supply for the Heater/Blower

50 EZCamera Shoe (998-4411-001) Quick-Connect (998-1105-001) PowerRite Power Supply (451-2750-018) and separate 24 VAC Power supply for the Heater/Blower

Quick-Connect (998-1105-001)

Vaddio DomeVIEW Outdoor, Environment Pendant Mount Dome Installation and User Guide - Document 341-445 Rev C

Page 2 of 14

Outdoor Pendant Mount Dome Enclosures Only (Cameras Not Included)

The Outdoor Pendant Mount Dome Enclosures are for use with existing or standard Sony EVI-D70 and Canon VC-C50iR. The Dome enclosures can also be used with the Vaddio Standard EZCamera Cable system for the EVI-D70 or the VC-C50i analog PTZ cameras. The dome enclosures without cameras are listed below:

998-9200-050 Outdoor Pendant Mount Dome Enclosure includes:

QTY Description

998-9200-070 Outdoor Pendant Mount Dome Enclosure includes:

QTY Description

INSTALLATION INSTRUCTIONS

DomeVIEW System Packages with Dome, Camera and Internal Mounting Bracket

999-9200-050 DomeVIEW 50iR Outdoor Pendant Mount Dome System 999-9200-070 DomeVIEW 70 Outdoor Pendant Mount Dome System

Outdoor Pendant Mount Dome Enclosures

998-9200-050 for the Canon VC-C50iR PTZ Camera 998-9200-070 for the Sony EVI-D70 PTZ Camera

For PAL camera part numbers, the last digit is changed to “1” (i.e. 999-9200-071 is a DomeVIEW 70 PAL camera).

The instructions are for both PAL and NTSC.

Before Starting the Installation

For cabling requirements, see the Cabling Requirements section. All installation work must conform to local building codes and should be performed by qualified personnel.

Vaddio DomeVIEW Outdoor, Environment Pendant Mount Dome Installation and User Guide - Document 341-445 Rev C

Page 3 of 14

Step-by-Step Assembly Instructions:

1) Unpack and verify the contents of the packaging against the lists on pages 2 and 3 of this manual. Carefully remove all parts from the packaging.

2) Remove the dome from the dome housing assembly using the provided proprietary Allen wrench.

NOT LOSE THIS WRENCH.

Use caution when handing the dome to avoid scratching or scuffing the dome

bubble.

3) The dome assembly consists of four major components (Figure2):

A. Foam Dust Plug to lock dust out of the dome B. Dome housing assembly

Figure 2:

Major Components of the Dome Housing Assembly

C. Mounting Plate with heater/blower pre-

mounted on the plate (single fan)

D. 8.2” Smoke tinted dome with stainless

screws attached

4) It is easiest to mount the dome on the 1-1/2” pipe mount and then install the contents of the dome to avoid cabling problems as the dome is spun onto the pipe mount. The dome can be mounted to a 1-1/2” NPT pipe extension attached to the Vaddio Ceiling Pendant Mount (part # 998-9300-002) or Curved Wall Mount (part # 998-9300-000). These mounts are sold separately. To install the dome to a 1-1/2” NPT Pipe Extension or Wall Mount:

A. Thread 1-1/2” lock nut onto pipe mount to

the top of the threads.

B. Generously apply pipe thread sealer (Figure

3) and install the dome on 1-1/2” NPT pipe

1.5” NPT Mount

Thread on Lock Nut to top

1-1/2” NPT Pipe Adapter

Figure 3

Apply pipe thread sealer to lock out moisture

by rotating counter-clock wise until threads are fully engaged – at least 5 full turns!

C. Additional sealer will be applied in a later

step (keep tube handy). The lock nut will be tightened in a later step as well.

5) Remove the Heater/blower fan assembly, mounting platform secured with three Philips head 10-32 x .5” flat head screws as shown in Figure 4.

A. First, loosen the two screws on the plate

that are key-holed, do not remove the screws. Then fully remove the third screw from the mounting plate.

Note: Only one (1) fan will be mounted to this plate

B. Slide the two loosened screws through the

keyholes and remove the plate. The mounting plate will be attached to a safety tether. Let the plate hang fro the tether while terminating the heater/blower.

C. The heater/blower circuitry will be

accessible on the back of this mounting plate.

D. Remove the foam dust plug (A –Figure 2)

and pull the cabling through into the dome.

E. Reinstall the foam dust plug.

Figure 4:

Remove the heater/blower mounting platform

Vaddio DomeVIEW Outdoor, Environment Pendant Mount Dome Installation and User Guide - Document 341-445 Rev C

Page 4 of 14

6) The heater/blower circuit card (Figure 5) receives power from the included 24 VAC power supply.

power supply powers the fans and heater strip onl y.

This

The 24 VAC output is not used with Vaddio camera systems. The video in and out is not used with Vaddio EZCamera cabling systems.

A. The 24 VAC power supply is connected to

the AC terminals (24 VAC IN) on the circuit board to power both the heater and the fan.

B. Connect the heater strip and fan connectors

on the circuit board.

C. Pull the camera cabling through the center

or backside of the mounting plate making sure that the cabling does not contact the heater strip.

D. Re-install the mounting plate inside the

dome. Tighten down the three screws making sure the safety tether and all other cables are tucked up behind the mounting plate to avoid interference with the PTZ

Figure 5:

Heater/blower circuit with connections, Use 2-cond 18AWG unshielded cable and locate power supply within 100’ (30.48m of the dome enclosure). The 24VAC OUT is not used.

camera movement.

NOTE: the Power supply for the heater/blower must be located within 100’ (30.48m) of the dome enclosure.

7) The camera brackets are attached to the heater/blower mounting plate through two (2) ¼” threaded holes on the plate labeled F (Figure 6). For all mounts the hex shaped stand-offs are ¼”Male to 8-32-Female with the length of the stand-off

Note: Only one (1) fan will be mounted to this plate

determining the height of the camera in the dome.

8) See Figure 7, thread the stand-offs (7) into the Fholes in the mounting plate inside the dome (8) and attach the camera mounting stage (6) to the standoffs with the 8-32 x .5” flat head screws (5).

Figure 6:

Two (2) ¼”-Male to 8-32 Female standoffs mount to holes marked “F”

Canon VC-C50iR Camera Only (Figure 7 on the following page)

9) Attach the EZCamera Cabling Shoe (4 - Figure 7) to the Canon VC-C50iR (DomeVIEW 50iR Outdoor Pendant Dome only).

A. When mounting the Canon VC-C50iR without the EZCamera Cabling System – skip this step.

10) Attach the camera (3) to the camera mounting stage (6) with two 8-32 x .5” pan head screws (2) and two #8 lock washers (see Figure 5). Skip to Step 15.

Back Front

Vaddio DomeVIEW Outdoor, Environment Pendant Mount Dome Installation and User Guide - Document 341-445 Rev C

Page 5 of 14

+ 9 hidden pages