VADDIO CLEARVIEW HD-20SE Installation And User Manual

Installation and User Guide

VADDIO™ CLEARVIEW™ HD-20SE

ClearVIEW HD-20SE High Definition, Robotic PTZ Camera

Model Number 999-6980-000 (North America)
Model Number 999-6980-001 (International)
Model Number 999-6980-000AW (North America) Arctic White Camera
Model Number 999-6980-001AW (International) Arctic White Camera

© 2015 Vaddio - All Rights Reserved. ClearVIEW HD-20

SE HD

PTZ Camera - Document Number 342-0933 Rev C

ClearVIEW HD-20SE

TABLE OF CONTENTS

Overview .................................................................................................................................................................... 3

Unpacking: ................................................................................................................................................................. 4

Front View with Feature Call-outs .......................................................................................................................... 5

Image: ClearVIEW HD-20SE HD PTZ Camera ................................................................................................. 5 

Rear Panel Connections with Feature Call-outs .................................................................................................... 6

Image: ClearVIEW HD-20SE HD PTZ Camera ................................................................................................. 6 

First Time Set-up with the ClearVIEW HD-20SE: ...................................................................................................... 7

Image: Rear Panel Connections ....................................................................................................................... 7

Drawing: Dip Switch and Resolution Label on the Bottom of the ClearVIEW HD-20SE .................................... 7

Image: Basic Connectivity Example of the ClearVIEW HD-20SE ...................................................................... 8 

Installation Basics: ................................................................................................................................................. 8

Compliance and CE Declaration of Conformity - ClearVIEW HD-20SE .................................................................... 9

Warranty Information ............................................................................................................................................... 10

General Specifications: ............................................................................................................................................ 11

Appendix 1: YPbPr Video Pin-Out for the HD-20SE Camera ................................................................................ 11

EZ-Power Video RJ-45 Connector Pin-outs ........................................................................................................ 12

Drawing: ClearVIEW HD-20SE Dimensions .................................................................................................... 12

Communication Specification .................................................................................................................................. 13

HD-20SE Command List (1/2) ........................................................................................................................... 13

HD-20SE Command List (2/2) ........................................................................................................................... 14

HD-20SE Inquiry List (1/1) ................................................................................................................................ 15

Table: HD-20SE OSD Menu Structure .................................................................................................................... 16

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 2 of 18

ClearVIEW HD-20SE

prop

O

VERVIEW

:
The amazing ClearVIEW HD-20
literally combines all of the best features of the ClearVIEW HD­18, HD-19 and HD-20 HD PTZ cameras into ONE! The
innovation of the HD-18 EZCamera™ Cat-5 interfaces, the low
light capability of the HD-19 and the FULL HD performance of
the HD-20 are all represented, and improved upon with the

SE.

ClearVIEW HD-20

The ClearVIEW HD-20

best ClearVIEW ever, and here’s why.

SE

The HD-20

is a native 1080p/60 camera using the latest
1/2.8-Type Exmor® high-speed, low noise CMOS image sensor
technology with 2.38 Megapixels (total) and 2.14 Megapixels
(effective). The ISP (image signal processor) is off-the-hook, not
only, providing fast, razor-sharp auto-focus routines with
incredible detail, realistic textures and vivid colors with an
impressive low-light performance of 0.3 Lux color and 0.03 Lux
(B/W). The lens is a 20X optical zoom multi-element glass lens
with an impressive horizontal field of view of 63° on the wide end
to 3.47° on the tele end. The outputs are simultaneous HDMI,
YPbPr and HSDS™ (differential video for use with Quick­Connect™ Interfaces) and supports both drop frame and non­drop frame HD video resolutions of 1080p/60/59.94/50/30/25,
1080i/60/59.94/50 and 720p/60/59.94/50.

So to recap, latest technology, awesome ISP, superb low-light performance, po werful yet wide angl e len s, lots an d
lots of video outs, drop and non-drop frame video, Full HD and there’s more!

SE

The ClearVIEW HD-20

can be used stand-alone or with one of four Quick-Connect Interface options. The Quick­Connect SR (YPbPr out), Quick-Connect DVI/HDMI-SR (HDMI or DVI-D and YPbPr outs) and the Quick-Connect
USB (USB 2.0 or IP-H.264 streaming with simultaneous HDMI and YPbPr outputs) and the Quick-Connect
Universal CCU.

SE

The ClearVIEW HD-20

is an exceptional value and a remarkable camera for even the most demanding HD video
applications including House of Worship productions, pro A/V system integrations, distance learning classrooms,
live events, IMAG systems, UCC applications, videoconferencing, distance learning, lecture capture and more!. To
top it all off, the ClearVIEW HD-20

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested
for use indoors with the power supply provided. The use of a power supply other than the one provided or outdoor
operation has not been tested and could damage the device and/or create a potentially unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or
damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of
electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not
work well for professional installations and can be the cause of intermittent conn ections which
can result in the RS-232 control line failing and locking up, and/or compromising the HSDS (high
speed differential) signals. For best results please use standard RJ-45 connectors and test all
cables for

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 3 of 18

SE

HD PTZ Camera quite

ClearVIEW
HD-20

Black

SE

is clearly the

ClearVIEW

SE

HD-20

Arctic White

SE

cameras are available in black or arctic white and are made in the USA.

er pin-outsprior to use and connection to Vaddio product.

in

(AW)

SE

in

ClearVIEW HD-20SE

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

U

NPACKING

Carefully remove the product and all of the included parts from the packaging.
Identify the following parts for each camera:

ClearVIEW HD-20

Part Number: 999-6980-000

 One (1)
 One (1) Vaddio IR Remote Commander
 One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)
 One (1) 12 VDC, 3.0 Amp Power Supply with Power Cord for North America
 Quick-Start Guide (1-pager)

Note: Full Manuals are downloaded from support.vaddio.com

ClearVIEW HD-20

Part Number: 999-6980-001

 One (1)
 One (1) Vaddio IR Remote Commander
 One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)
 One (1) 12 VDC, 3.0 Amp Power Supply
 One (1) Euro Power Cable
 One (1) UK Power Cable
 Quick-Start Guide (1-pager)

Note: Full Manuals are downloaded from support.vaddio.com

ClearVIEW HD-20

Part Number: 999-6980-000AW (Artic White Version)

 One (1)
 One (1) Vaddio IR Remote Commander
 One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)
 One (1) 12 VDC, 3.0 Amp Power Supply with Power Cord for North America
 Quick-Start Guide (1-pager)

Note: Full Manuals are downloaded from support.vaddio.com

ClearVIEW HD-20

Part Number: 999-6980-001AW (Artic White Version)

 One (1)
 One (1) Vaddio IR Remote Commander
 One (1) EZCamera™ Control Adapter (RJ-45 to DB-9)
 One (1) 12 VDC, 3.0 Amp Power Supply
 One (1) Euro Power Cable
 One (1) UK Power Cable
 Quick-Start Guide (1-pager)

Note: Full Manuals are downloaded from support.vaddio.com

ClearVIEW HD-20

:

SE,

HD PTZ Camera (North America):

ClearVIEW HD-20

SE

, HD PTZ Camera (International):

ClearVIEW HD-20

SE,

HD PTZ Camera (North America):

ClearVIEW HD-20

SE

, HD PTZ Camera (International):

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 4 of 18

SE

Camera (998-6980-000)

SE

Camera (998-6980-000)

SE

Camera (998-6980-000AW)

SE

Camera (998-6980-000AW)

ClearVIEW HD-20SE

Front View with Feature Call-outs

SE

Image: ClearVIEW HD-20

①

HD PTZ Camera

②

③

④

1) Camera and Zoom Lens:

The 20X optical zoom lens is built around a (1/2.8 Type) high-speed, low-noise Exmor CMOS image senso r with a
total of 2.38 total megapixels for precise HD video image acquisition.

2) Red Tally Light:

A red tally light is illuminated when the camera receives a command from an external control system.

3) IR Sensors:

SE

IR sensors are built into the front of the ClearVIEW HD-20
supplied with the camera.

4) Blue Power Light:

A Vaddio blue LED power light is illuminated when the camera is turned on. This LED will blink when IR signals
are received.

to receive IR signals from the IR remote control

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 5 of 18

ClearVIEW HD-20SE

Rear Panel Connections with Feature Call-outs

SE

Image: ClearVIEW HD-20

⑤

⑥

HD PTZ Camera

⑨

⑩

⑦

⑪

⑧

5) RS-232 IN & IR Out (Color Coded Blue):

The RS-232 accepts modified VISCA protocol for camera control, as well as transmits IR signaling received by the IR receivers,
which can be transmitted to third party devices through the Quick-Connect SR or Quick-Connect DVI/HDMI-SR interfaces only.

6) Dip Switch Settings:

Settings for IR remote, baud rate and image flip can be configured on these s witches. See the Switch Settings page for
additional information.

7) HD Video Select:

A rotary switch allows the user to choose the component HD output video resolution and format. See the Switch Settings page
for additional information.

HD Resolution Note: When changing the resolution of the camera, the camera may have to be po wer-cycled after
the change. The switcher typically will require a reboot or rescan.

8) 12 VDC Input:

SE

Power input for the standard, ClearVIEW HD-20

9) HDMI Output:

The HDMI output feeds out HD digital video only (no copy protect or device communication is included). The HDMI output is
optimized for HD video signals (seems logical).

10) YPbPr Output:

Component HD video (YPbPr) is output through the DE-15 connector. YPbPr and HDMI signals are simultaneous. Limited SD
resolutions are supported.

11) EZ-POWER VIDEO Port (Color Coded Orange):

This RJ-45 connector is only used with the Quick-Connect SR Interface, Quick-Connect DVI-D/HDMI SR Interface and the
Quick-Connect USB Interface to supply power and return HSDS (differential) video from the camera.

12) Slot for Optional Cards:

An EZIM CCU Slot Card is available for use with the Quick-Connect Universal CCU and is plugged into this slot.

camera power supply.

⑫

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 6 of 18

ClearVIEW HD-20SE

F

IRST TIME SET-UP WITH THE CLEAR

VIEW HD-20SE:

The ClearVIEW HD-20SE was designed to be a high quality camera that is very easy to use and operate. There is

SE

documentation at the back of this manual for pin-outs of the connectors on the ClearVIEW HD-20

camera.

Step 1: Using the HD VIDEO SELECT rotary switch and CAMERA SETTINGS dip switches on the back of the
camera, set up the camera’s output resolution and functional preferences. There is a label on the bottom of the
camera that identifies the choices.

Important Dip Switch Note: Setting all dip switches down and power cycling the camera will load the factory default camera settings. For the
first time set-up, loading the defaults may be a good idea

.

Image: Rear Panel Connections

HD Video Select Switch

Camera Settings 10-Pos Dip Switch

HD-20SE Rear Panel

SE

Drawing: Dip Switch and Resolution Label on the Bottom of the ClearVIEW HD-20

IR 1

1 & 2 UP

IR 2ONIR 3

ON

21

1234

DIP SWITCH SETTINGS

IR

9600

bps

38400

bps

4

5

OFF

5

56

OUT
OFF

ON

3

IMAGE

HDMI

6

COLOR

YCbCr

sRGB

COLOR

7

7

FLIP
OFF

ON

8

OFF

68109

9

10

OFF

OFF

910

0
1
2
3
4
5
6
7

HD VIDEO SELECT

720p/59.94

1080i/59.94

1080p/59.94

720p/60

1080i/60

1080p/60

720p/50

1080i/50

1080p/50

8
9

A
B
C
D

1080p/30

E

1080p/25

F

 Set the desired and available HD output resolution for the camera with the Rotary Switch.
 Set the IR frequency of the camera if it is to respond to the IR remote control.
 If using the IR forwarding feature, set the IR OUT switch to ON (SW3).
 Set the Baud Rate dip switch (SW4) to 9600bps for most applications. Default for Vaddio EZCamera

Cabling Systems is 9600bps.

 To set the HDMI or DVI color space, use dip switch 7 (SW7).
 If inverting the camera, turn the IMAGE FLIP ON (SW8).

Dip Switch Settings:

IR 1 & 2: The IR remote has the capability of operating up to three different PTZ cameras from one remote.
Use the selector buttons at the top of the IR remote to select the frequency.
IR Out 3: The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on the IR

output will allow IR signals to be transmitted over the Cat-5 cable to the head end. When using RS-232 control
or Vaddio CCU controllers (also via RS-232), turn the IR OUT to OFF (up).

Baud Rate 4: The options for baud rate are either 9600 bps or 38,400 bps.
HDMI Color or sRGB Color space 7: Default is YCbCr. Use sRGB color space with olde r DVI-D 1.0 monitors
only. The YCbCr color space is best for HDMI digital video.
Image Flip 8: To invert the HD-20, turn the IMAGE FLIP ON (switch down).
Switches 5, 6, 9 and 10: Leave up - or in the OFF position.

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 7 of 18

ClearVIEW HD-20SE

Image: Basic Connectivity Example of the ClearVIEW HD-20SE

Camera with local power connected to ProductionVIEW™ Precision Camera Controller

Rear of

ClearVIEW

HD-20

SE

12VDC, 3.0A

Power Supply

(Local)

RS-232

ProductionVIEW Precision Camera Controller

Installation Basics:

Locate the camera mounting location paying close attention to camera viewing angles, lighting conditions, possi ble
line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted. Pick a mounting
location that will optimize the performance of the camera.

RS-232 Cabling:

For RS-232, use a standard Cat-5 cable (568B termination for RJ-45 co nnectors) from the RS-232 port on the ba ck
of a Vaddio ProductionVIEW camera controller or switcher. If the camera will be connected to a third-party control
system (such as AMX or Crestron), a DE-9 to RJ-45 adapter is supplied with the camera for RS-232.

.

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 8 of 18

YPbPr

HDMI

HD Monitor (Simulated Video Feeds)

Other YPbPr FEED

ClearVIEW HD-20SE

C

OMPLIANCE AND CE DECLARATION OF CONFORMITY - CLEAR

Compliance testing was performed to the following regulations:

 FCC Part 15 (15.107, 15.109), Subpart B Class A
 ICES-003, Issue 4: 2004 Class A
 EN 55022 A: 2006 + A1: 2007 Class A
 KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A
 KN22 2008 (CISPR 22: 2006) Class A
 EMC Directive 2004/108/EC Class A


EN 55024: A2: 2003

Class A

VIEW HD-20

SE

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his/her own
expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device
must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void the
user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:

EMC Directive 2004/108/EC
EN 55022 A: 2006 + A1: 2007(CISPR 22:2005/A1:2005)
EN 55024: 1998 + Amendments A1: 2001 + A2: 2003

 EN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge
 EN 61000-4-3: 2006 + A1: 2008 Radiated Immunity
 EN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients
 EN 61000-4-5: 2006 Surge Immunity
 EN 61000-4-6: 2009 Conducted Immunity
 EN 61000-4-8: 2010 Power Frequency Magnetic Field
 EN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations

KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002)

 EN 61000-4-2 Electrostatic Discharge
 EN 61000-4-3 Radiated Immunity
 EN 61000-4-4 Electrical Fast Transients
 EN 61000-4-5 Surge Immunity
 EN 61000-4-6 Conducted Immunity
 EN 61000-4-8 Power Frequency Magnetic Field
 EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

IEC 60950-1:2005 (2nd Edition); Am 1:2009
EN 60950-1:2006+A11:2009+A1:2010+A12:2011

Safety

Safety

Radiated and Conducted Emissions
Immunity

IT Immunity Characteristics

ClearVIEW HD-20

SE,

Document Number 342-0933 Rev C Page 9 of 18

ClearVIEW HD-20SE

WARRANTY INFORMATION

(See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):

Hardware* Warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured products. Vaddio warrants

its manufactured products against defects in materials and workmanship for a period of two years from the day of purchase, to
the original purchaser, if Vaddio receives notice of such defects during the warranty. Vaddio, at its option, will repair or replace
products that prove to be defective. Vaddio manufactures its hardware products from parts and components that are new or
equivalent to new in accordance with industry standard practices.

Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate maintenance by the customer,
customers applied software or interfacing, unauthorized modifications or misuse, mishandling, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, modified power supply or improper site operation
and maintenance. OEM products and products manufactured by other companies are excluded and are covered by the
manufacturer’s warranty.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty. If the product is out of warranty, Vaddio will test then repair the product or products. T he cost of parts and labor
charge will be estimated by a technician and confirmed by the customer prior to repair. All compon ents must be returned for
testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.

Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs and/or
replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at

[e-mail] or online at vaddio.com.

Return Material Authorization (RMA) Number: Before returning a product for repair or replacement request an RMA from
Vaddio’s technical support. Provide the technician with a return phone number, e-mail address, shipping address, product serial
numbers and original purchase order number. Describe the reason for repairs or returns as well as the date of purchase. See
the General RMA Terms and Procedures section for more information. RMA’s are valid for 30 days and will be issued to Vaddio
dealers only. End users must return products through Vaddio dealers. Include the assigned RMA number in all correspondence
with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when returning the product. All products
returned for credit are subject to a restocking charge without exception.

Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, use of incorrect po wer supply, use of a modified power
supply or unauthorized repair.

Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and insurance
charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound frei ght carrier.
If the return shipment appears damaged, retain the original boxes an d packing material for inspection b y the carrier. Contact

your carrier immediately.
Products not under Warranty: Payment arrangements are required before outbound shipment for all out of warranty products.

Other General Information:
Care and Cleaning

Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

 Do not spill liquids in the product
 Keep this device away from food and liquid
 For smears or smudges on the product, wipe with a clean, soft cloth
 Use a quality lens cleaner on the lens
 Do not use any abrasive chemicals.

Operating and Storage Conditions:

Do not store or operate the device under the following conditions:

 Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)
 High humi dit y, condensing or wet environments
 In inclement weather
 In swimming pools or beaver dams
 Dry environments with an excess of static discharge
 In orbit (vacuum, temperature and re-entry problem)
 Under severe vibration

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 10 of 18

ClearVIEW HD-20SE

GENERAL SPECIFICATIONS:

ClearVIEW HD-20SE, HD PTZ Camera

Part Numbers 999-6980-000 (North America), 999-6980-001 (Int’l) - Black Camera Version

999-6980-000AW (North America), 999-6980-001AW (Int’l) - Artic White Camera Version

Image Sensor 1/2.8-Type Exmor, high-speed, low-noise CMOS Image Sensor

2.38 Megapixels (2.14M effective pixels).
Zoom 20X Optical Zoom with Multi-element Glass Lens
Field of View Horizontal: 63º Wide End to 3.47º Tele End, (16:9 Aspect Ratio)

Vertical: 36.8˚ Wide End to 1.85˚ Tele End
Lens Focal Length f=4.44mm to 89mm / F1.6 - F3.4
Minimum Illumination Color: 0.3 Lux (F1.6, 1/30 sec, 50 IRE), B/W: 0.03 Lux (F1.6, 1/30 sec, 50 IRE)
Video Resolutions HD: 1080p/60/59.94/50./30/25, 1080i60/59.94/50 and 720p/60/59.94/50

HD Video Resolutions Only at 16:9
White Balance Auto, Manual (Red and Blue Gain), OPWB, Indoor, Outdoor and Fluorescent
Video Output Formats HDMI, Analog Component, HSDS (Differential Video, Power and Control for Quick-Connects)
Signal to Noise Ratio Greater than 50 dB (AGC: Off)
Compatible Quick-

Connects
Pan Range Pan: +170 degrees to -170 degrees, Tilt: +90 degrees to -30 degrees
Preset Positions 16 (internal), 6 recalled via IR Remote
Control Methods RS-232, IR Remote Commander and OSD (on screen display)
Tally Light Available through RS-232 Control
HD Video Select 16-Position Rotary Switch: Used to set HD Video Resolution Output
Camera Settings 10-Position Dip Switch: Settings for IR Select, Baud Rate 9600, Image Flip and Col or Space
Accessory Slot Cards EZIM CCU Slot Card, Part Number 998-6900-006
Dimensions/Weight 7.81” (198.37mm) H x 6.67” (169.42mm) W x 7.057” (179.25. mm) D / 5.6 lbs. (2.630835643 kg.)

Quick-Connect SR, Quick-Connect DVI/HDMI SR, Quick-Connect USB and Quick-Connect

Universal CCU

APPENDIX 1: YPBPR VIDEO PIN-OUT FOR THE HD-20SE CAMERA

Pin YPbPr

1 Pr
2 Y
3 Pb
4 ­5 ­6 Pr GND
7 Y GND
8 Pb GND

9 ­10 GND
11 ­12 ­13 ­14 ­15 -

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 11 of 18

ClearVIEW HD-20SE

V

EZ-Power Video RJ-45 Connector Pin-outs

Important Note: The EZ-POWER VIDEO RJ-45 Connector is for use with the Quick-Conn ect SR, Quick-
Connect DVI/HDMI SR and Quick-Connect USB Interfaces ONLY (568B Wiring Standard). The video

signals are differential (HSDS) and can only be received by the interfaces above.

Pin YPbPr

1 Power+
2 Power­3 Y+
4 PB+
5 PB ­6 Y ­7 PR+
8 PR-

Drawing: ClearVIEW HD-20

SE Dimensions

Optional Accessories:

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 12 of 18

EZ-POWER

IDEO

12345678

Thin Profile Wall Mount

Part Number: 535-2020-230

ClearVIEW HD-20SE

COMMUNICATION SPECIFICATION

Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control

12345678

Pin # RJ-45 RS-232 and IR Out Pins

1) Unused

2) Unused

3) Unused

4) IR Output (Diff Signal to Quick-Connect SR)

5) IR Ground (Diff Signal to Quick-Connect SR)

6) GND (GND of IR Short Range - Pin 3)

7) RXD (from TXD of control source)

8) TXD (to RXD of control source)

NOTE: The Vaddio ClearVIEW HD-20

SE Control Protocol is similar, but not identical to, the Sony® VISCA™

command set in order to be compatible with several popular control devices. Not all VISCA commands are
supported and there are many HD-Series specific commands in the following Command and Inquiry Lists.

SE Command List (1/2)

HD-20

Command Set Command Command Packet Comments

Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On

Off(Standby)

CAM_Zoom Stop

Tele(Standard)
Wide(Standard)
Tele(Variable)
Wide(Variable)
Direct
Direct(Variable)

CAM_Focus Stop

Far(Standard)
Near(Standard)
Far(Variable)
Near(Variable)
AutoFocus
ManualFocus
Auto/Manual
Direct

CAM_WB Auto

Manual
Indoor
Outdoor
One Push WB

CAM_RGain Reset

Up
Down
Direct

CAM_BGain Reset

Up
Down
Direct

CAM_AE Full Auto

Manual
Shutter Priority
Iris Priority

CAM_Iris Reset

Up
Down
Direct

CAM_Gain Reset

Up
Down
Direct

CAM_Bright Reset

Up
Down
Direct

8x 01 04 00 02 FF
8x 01 04 00 03 FF

8x 01 04 07 00 FF
8x 01 04 07 02 FF
8x 01 04 07 03 FF
8x 01 04 07 2p FF
8x 01 04 07 3p FF
8x 01 04 47 0p 0q 0r 0s FF
8x 01 7E 01 4A 0v 0p 0q 0r 0s FF

8x 01 04 08 00 FF
8x 01 04 08 02 FF
8x 01 04 08 03 FF
8x 01 04 08 2p FF
8x 01 04 08 3p FF
8x 01 04 38 02 FF
8x 01 04 38 03 FF
8x 01 04 38 10 FF
8x 01 04 48 0p 0q 0r 0s FF

8x 01 04 35 00 FF
8x 01 04 35 05 FF
8x 01 04 35 01 FF
8x 01 04 35 02 FF
8x 01 04 35 03 FF

8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 0p 0q 0r 0s FF

8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 43 0p 0q 0r 0s FF

8x 01 04 39 00 FF
8x 01 04 39 03 FF
8x 01 04 39 0A FF
8x 01 04 39 0B FF

8x 01 04 0B 00 FF
8x 01 04 0B 02 FF
8x 01 04 0B 03 FF
8x 01 04 4B 00 00 0p 0q FF

8x 01 04 0C 00 FF
8x 01 04 0C 02 FF
8x 01 04 0C 03 FF
8x 01 04 4C 00 00 0p 0q FF

8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF

Power On/Off

pqrs: Zoom Position*
v:(Speed) 0-7

pqrs: Focus position*

pqrs:00-0xffff

pqrs:00-0xffff
Auto Exposure Mode

Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode (default)

pq(0x00-0x08)

pq(0x00-0x2A)

pq(0x01-0x64)

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 13 of 18

ClearVIEW HD-20SE

HD-20SE Command List (2/2)

Command Set Command Command Packet Comments

CAM_Backlight On

CAM_Aperture Reset

CAM_Memory Reset

CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_LR_Reverse On On

IR_Receive## On

Pan-tiltDrive Up

Pan-tilt-zoom Drive Up

Tally On

Preset Pan Speed Pan/Tilt/Zoom Speed 8x 01 7E 01 0B WW SS ZZ FF WW: Pan Speed (0x01-0x18)

Motor Config Hard Motor Stops

BLK.Enhance Pedestal No Support No Support
GMA.Enhance Gamma 8x 01 7E 54 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance Chroma 8x 01 7E 55 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance Knee No Support No Support
DIS.Enhance Digital Image

SNR.Enhance Super Noise

AGC.Enhance AGC Mode 8x 01 7E 59 00 FF

CAM_Shutter Reset

CAM_ExpComp On

CAM_ICR
Cut Filter

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 14 of 18

Off

Up
Down
Direct

Set
Recall

Off

Off
On/Off

Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
Absolute Position

Home
Reset

Down
Left
Right
Tele
Wide
UpLeft
UpRight
DownLeft
DownRight
Stop
Absolute Position

Off

Soft Motor Stops

Stabilizer

Reduction

Up
Down
Direct

Off
Reset
Up
Down
Direct

ICR On
ICR Off

8x 01 04 33 02 FF
8x 01 04 33 03 FF

8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 00 0p 0q FF

8x 01 04 3F 00 0p FF
8x 01 04 3F 01 0p FF
8x01 04 3F 02 0p FF

8x 01 04 61 02 FF
8x 01 04 61 03 FF

8x 01 06 08 02 FF
8x 01 06 08 03 FF
8x 01 06 08 10 FF

8x 01 06 01 VV WW 03 01 FF
8x 01 06 01 VV WW 03 02 FF
8x 01 06 01 VV WW 01 03 FF
8x 01 06 01 VV WW 02 03 FF
8x 01 06 01 VV WW 01 01 FF
8x 01 06 01 VV WW 02 01 FF
8x 01 06 01 VV WW 01 02 FF
8x 01 06 01 VV WW 02 02 FF
8x 01 06 01 VV WW 03 03 FF
8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
8x 01 06 04 FF
8x 01 06 05 FF

8x 01 06 0A VV WW XX 03 01 03 FF
8x 01 06 0A VV WW XX 03 02 03 FF
8x 01 06 0A VV WW XX 01 03 03 FF
8x 01 06 0A VV WW XX 02 03 03 FF
8x 01 06 0A VV WW XX 03 03 01 FF
8x 01 06 0A VV WW XX 03 03 02 FF
8x 01 06 0A VV WW XX 01 01 03 FF
8x 01 06 0A VV WW XX 02 01 03 FF
8x 01 06 0A VV WW XX 01 02 03 FF
8x 01 06 0A VV WW XX 02 02 03 FF
8x 01 06 0A VV WW XX 03 03 03 FF
8x 01 06 0B VV WW XX 0Y 0Y 0Y 0Y
0Z 0Z 0Z 0Z 0R 0R 0R 0R FF

8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF

8x 01 7E 01 70 00 00 FF
8x 01 7E 01 70 00 01 FF

8x 01 7E 57 02 FF
8x 01 7E 57 03 FF

8x 01 7E 58 02 FF
8x 01 7E 58 03 FF

8x 01 7E 59 01 FF
8x 01 7E 59 02 FF
8x 01 7E 59 03 FF

8x 01 04 0A 00 FF
8x 01 04 0A 02 FF
8x 01 04 0A 03 FF
8x 01 04 4A 00 00 0p 0q FF

8x 01 04 3E 02 FF
8x 01 04 3E 03 FF
8x 01 04 0E 00 FF
8x 01 04 0E 02 FF
8x 01 04 0E 03 FF
8x 01 04 4E 00 00 0p 0q FF

8x 01 04 01 02 FF
8x 01 04 01 03 FF

pq(0x00-0x1F)

p:Memory No(=0-0xF)

Mirror (Horizontal) on
Mirror (Horizontal) off

IR forwarding/Local IR
VV: Pan Speed (0x01-0x18)

WW: Tilt Speed(0x01-0x14)

YYYY: Pan Position**
ZZZZ: Tilt Position**

VV: Pan Speed (0x01-0x18)
WW: Tilt Speed(0x01-0x14)
XX: ZoomSpeed(0x00-0x07)

YYYY: Pan Position**
ZZZZ: Tilt Position**
RRRR: ZoomPosition**

SS:Tilt Speed(0x01-0x14)
ZZ:Zoom Speed(0-7);

On
Off

On
Off

Off
Low
Medium
High

pq(0x00-0x1C)
AutoExposure Off

AutoExpouse On

Pq: 0x00-0x2A
ICR On - Cut Filter Out

ICR Off - Cut Filter In

ClearVIEW HD-20SE

HD-20SE Command List (2/2) Notes

*Zoom and Focus Data:

CAM_Zoom: Range(0x000–0x071A)
CAM_Focus: Range (0x0ed-0x0944) dependent on Zoom Position

**Additional Information:

Pan Range: 8044 – 7FBC (-32,700 to +32,700)
Tilt Range: E891 – 4C2B (-5,999 to +19,499)
Actual Pan/Tilt ranges defined in Inquiry list

SE Inquiry List (1/1)

HD-20

Inquiry Command Command Response Packet Comments

CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF

CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqr: 0-0x071A
CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position
CAM_WBModeInq 8x 09 04 35 FF y0 50 00 FF

CAM_RGain 8x 09 04 43 FF y0 50 0p 0q 0r 0s FF pqrs: 000-0xffff
CAM_BGain 8x 09 04 44 FF y0 50 0p 0q 0r 0s FF pqrs: 000-0xffff
CAM_Iris 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq(0x00-0x08)
CAM_Gain 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq(0x00-0x2A)
CAM_Bright 8x 01 04 4D FF y0 50 00 00 0p 0q FF pq(0x01-0x64)
CAM_BacklightModeInq 8x 09 04 33 FF y0 50 02 FF

CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF Pq:x00-0x1F
CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FF p:Preset 0-0xf
CAM_IDInq 8x 09 04 3F FF y0 50 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
CAM_ReceiveInq 8x 09 06 08 FF y0 50 02 FF

CAM_LR_Reverse 8x 09 04 61 FF y0 50 02 FF

Pan-TiltMaxSpeedInq 8x 09 06 11 FF y0 50 pp qq FF pp:Pan 0x01-0x18

Pan-tiltPositionInq 8x 09 06 12 FF FF y0 50 0p 0p 0p 0p 0q 0q 0q 0q FF pppp: Pan 0x8044-0x7FB2

TallyInq 8x 09 7E 01 0A FF y0 50 02 FF

PresetSpeedInq 8x 09 7E 01 0B FF y0 50 pp qq rr FF pp:Pan 0x01-0x18

Motor Config 8x 09 7E 01 70 FF y0 50 00 FF

BLK.Enhance No support No Support Pedestal
GMA.Enhance 8x 09 7E 54 FF y0 50 00 00 0p 0q FF pq: Gamma (0x00-0x10)
CRM.Enhance 8x 09 7E 55 FF y0 50 00 00 0p 0q FF pq: Chroma (0x00-0x64)
KNE.Enhance No support No Support Knee
DIS.Enhance 8x 09 7E 57 FF y0 50 02 FF

SNR.Enhance 8x 09 7E 58 FF y0 50 02 FF

AGC.Enhance 8x 09 7e 59 FF y0 50 00 FF

CAM_AEModeInq 8x 09 04 39 FF y0 50 00 FF

CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq: 0x0-0x1C
CAM_ExpCompModeInq 8x 09 04 3E FF y0 50 02 FF

CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Pos
CAM_ICRModeInq 8x 09 04 01 FF y0 50 02 FF

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 15 of 18

y0 50 03 FF

y0 50 05 FF
y0 50 01 FF
y0 50 02 FF
y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

y0 50 03 FF

y0 50 01 FF

y0 50 03 FF

y0 50 03 FF

y0 50 01 FF
y0 50 02 FF
y0 50 03 FF
y0 50 04 FF

y0 50 03 FF
y0 50 0A FF
y0 50 0B FF

y0 50 03 FF

y0 50 03 FF

On
Off(Standby)

Auto
Manual
Indoor
Outdoor
One Push WB

On
Off

On
Off

On
Off

qq:Tilt 0x01-0x14

qqqq: Tilt 0xE890-0x4C2C
On

Off

qq:Tilt 0x01-0x14
rr:Zoom 0x00-0x07

Hard Motor Stops
Soft Motor Stops

On
Off

On
Off

Off
Low
Medium
High
Manual AGC

Auto Exposure Mode
Manual Control Mode
Shutter Priority Mode
Exposure Priority Mode

On - AE Mode Off
Off – AE Mode On

On - ICR filter Out
Off – ICR filter In

ClearVIEW HD-20SE

TABLE: HD-20SE OSD MENU STRUCTURE

Use this OSD menu with the IR Commander to make video adjustments (AWB, COLOR, EXP, etc…) on the HD-20SE Camera.

Menu Controls Modes/Range Default Notes

SSDR OFF OFF Dynamic Range Adjustment
ON SSDR 0-15 8* *When Dynamic Range is ON
Return Return to Main Menu

WHITE BAL ATW ON Auto White Balance - ON
MANUAL> RED 0 - 1000 560 Adjust Red Level
BLUE 0 - 1000 480 Adjust Blue Level
RETURN< Return to WHITE BAL Menu
AWC-SET
OUTDOOR Set to Outdoor when room has direct sun light and blue walls
INDOOR Set to Indoor when fluorescent lights start to cause color variation in ATW mode
MERCURY
SODIUM
RETURN< Return to Main Menu

BACKLIGHT OFF OFF Default BLC is off
WDR> LEVEL (LOW / MED / HIGH) OFF Wide Dynamic Range
RETURN<
BLC> LEVEL (LOW / MED / HIGH) OFF
BOTTOM 1-100
LEFT 1-100
RIGHT 1-100
RETURN< Return to BACKLIGHT Menu
HLC> LEVEL (LOW / MED / HIGH) OFF
MASK TONE 1-15
RETURN< Return to BACKLIGHT Menu
RETURN< Return to Main Menu

INTELLIGENCE OFF Intelligence, motion detection analytics and masking are not processed or used by the

FOCUS MODE AUTO / MANUAL / ONE PUSH AUTO
ZOOM TRACK> OFF / TRACK / AUTO TRACK AUTOTRACK
ZOOM SPEED> SLOW / MEDIUM / FAST
DIGITAL ZOOM> OFF/ON OFF Default is OFF
ON>LIMIT X2 - X16 Avoid Digital Zoom if possible
RETURN< Return to FOCUS Menu
Zoom POS INIT> OFF/AUTO Zoom position initialization
MANUAL>
POS INIT 1X - 20X 1X Sets INIT Zoom Position
RETURN< Return to FOCUS Menu
USER PRESET> OFF/ON OFF
ON > PRESET NO 1-128 1 Zoom Presets
PRESET SAVE
PRESET CLEAR
RETURN< Return to FOCUS Menu
LENS INIT MANUAL / AUTO
RETURN< Return to Main Menu

EXPOSURE BRIGHTNESS 0-100 50 Brightness Sets Luminance Target
IRIS> AUTO AUTO Automatic Gain Control

MANUAL> Closed to F28 Manual Iris
RETURN< Return to EXPOSURE Menu

SHUTTER A FLK Use Anti-Flicker when lighting causes color hunting
ESC
MANUAL> 1/30 - 1/30,000 sec. Shutter Speed
RETURN< Return to EXPOSURE Menu
AGC OFF / LOW /MED / HIGH LOW
MANUAL (OFF)>
AGC VALUE 0 - 36dB 0 dB Automatic Gain Control
RETURN<
SSNR OFF / LOW /MED / HIGH LOW Noise Reduction - Don’t use above Low
SENS-UP OFF OFF OFF - Do not Use
RETURN< Return to Main Menu

HD-20SE camera, however the OSD menu still works.

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 16 of 18

ClearVIEW HD-20SE

HD-20SE OSD Menu Structure (continued)

Menu Controls Range/Modes Default Notes

SPECIAL DAY/NIGHT> COLOR / B/W / AUTO COLOR Do not use
DIS> OFF / ON OFF Digital Image Stabilization - leave off
DEFOG OFF / ON / MANUAL/AUTO OFF Do not use
COMM ADJUST> BAUD RATE NEVER CHANGE THE BAUD RATE OR THE UART
UART

RETURN< Return to SPECIAL Menu

IMAGE ADJUST> H-REV ON / OFF OFF Use Dip Switch on Camera to Flip Image
V-REV ON / OFF OFF Use Dip Switch on Camera to Flip Image
SHARPNESS ON/OFF ON Picture Detail
ON> 0-30 15
RETURN< Return to IMAGE ADJUST Menu
MONITOR LCD>
GAMMA .0 -1.0 0.50
COLOR LEVEL 0-100 50
RETURN< Return to IMAGE ADJUST Menu
USER>
GAMMA .0 - 1.0 0.50
COLOR LEVEL 0-100 50
RETURN< Return to IMAGE ADJUST Menu
RETURN< Return to Main Menu
DISPLAY CAM TITLE ON / OFF OFF
ON> A-Z, 1-9
RETURN< Return to DISPLAY Menu
CAM ID ON / OFF OFF
CAM INFO ON / OFF OFF
ZOOM MAG ON/OFF OFF
OSD COLOR WHITE WHITE/YELLOW/GREEN/RED/BLUE
LANGUAGE

SET LANGUAGE
RETURN< Return to Main Menu
VIDEO OUT FORM COMPONENT ON / OFF ON Do not change this parameter
RETURN< Do not change resolutions here - Use the

RESET
EXIT

SETTINGS - Control is lost if these are changed.
Factory default reboot will be required.

ENGLISH (ENG, FR, KOR, SP, CHIN, JAP, PORT,

RUS, DUT, ITAL)

Rotary Switch on the back of the camera

ClearVIEW HD-20

SE, Document Number 342-0933 Rev C Page 17 of 18

y

ClearVIEW HD-20SE

©2015 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing are
subject to change without notice or obligation. Vaddio, ClearVIEW, ProductionVIEW, EZCamera, Quick-Connect and HSDS are trademarks of

ClearVIEW HD-20

Vaddio. All other trademarks are propert

SE, Document Number 342-0933 Rev C Page 18 of 18

Toll Free: 800-572-2011 ▪ Phone: [phone] ▪ FAX: [phone]

of their respective owners. Document Number 342-0933 Rev C, SD: 68669.9

www.vaddio.com