VAR |
MODEL |
CUSTOMER |
CAT. NO. |
A |
B |
XN |
HP |
VOLTS |
SF |
SF AMPS |
HZ |
RPM |
PREM. EFF. LABEL |
THP LABEL |
CALIFORNIA TITLE 20 LABEL |
DESCRIPTION / REMARKS |
|||
001 |
K63JXEAT-5224 |
POOL AFTERMARKET |
EB227 |
12.83 |
N/A |
N/A |
3/4 |
230/115 |
1.00 |
4.4/8.8 |
60 |
3450 |
NO |
YES |
|
COMPLIANT |
|
||
002 |
K63CXEAU-5225 |
POOL AFTERMARKET |
EB228 |
13.33 |
N/A |
N/A |
1.0 |
230/115 |
1.00 |
6.0/12.0 |
60 |
3450 |
NO |
YES |
NON-COMPLIANT |
|
|||
003 |
K63CXEAV-5226 |
POOL AFTERMARKET |
EB229 |
13.58 |
N/A |
N/A |
1.5 |
230/115 |
1.00 |
7.0/14.0 |
60 |
3450 |
NO |
YES |
NON-COMPLIANT |
|
|||
004 |
K63CXEAW-5227 |
POOL AFTERMARKET |
EB230 |
14.58 |
N/A |
N/A |
2.0 |
230/115 |
1.00 |
9.0/18.0 |
60 |
3450 |
NO |
YES |
NON-COMPLIANT |
|
|||
005 |
K63CXEAY-5228 |
POOL AFTERMARKET |
EB231 |
14.33 |
N/A |
N/A |
2.5 |
230 |
1.00 |
10.5 |
60 |
3450 |
NO |
YES |
NON-COMPLIANT |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
REV. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
E |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
GROUND
LUG
1/2-14 NPT
CONDUIT HOLE
WITH PLUG
REV.
E
CALIFORNIA
TITLE 20 LABEL
NOTES:
1.300 SERIES STAINLESS STEEL SHAFT EXTENSION.
NIDEC MOTOR CORPORATION 23-Oct-18
A ±.060
THP LABEL
(PER CHART 
1.875 ±.015 
ABOVE & BOM)
NAMEPLATE
| <![if ! IE]> <![endif]>TOP |
<![if ! IE]> <![endif]>TOP |
TOP
.6250
.6245
AQUA SHIELD LABEL |
|
|
|
|
|
|
n |
A |
.006 |
||
7/16-20 UNF-2A R.H. THREAD
SERIALIZED LABEL
(POOL AFTERMARKET) THREAD PROTECTOR
6.5 
5.875 DIA. BOLT CIRCLE 
3/8-16 UNC-2B TYP.
4 PLACES, EQUALLY SPACED
.750" DEEP
.69 
SHAFT
SEAL
WATER 
SLINGER
-A-
4.500 +.000 
-.003
a A .006
#10-32 UNF-2B L.H. THREAD |
|
.375" DEEP MIN. |
REFER TO S.E.I.M. 24-1 |
|
REVISION RECORD FOR: |
ECO E32423 |
TOLERANCES ON DIMENSIONS |
NIDEC MOTOR CORPORATION |
|
|
|
|
|
||||
ADDED COLUMN "CALIFORNIA TITLE 20 LABEL" IN CHART. |
|
(UNLESS OTHERWISE SPECIFIED) |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
||||
ADDED NOTE "CALIFORNIA TITLE 20. |
|
|
|
|
INFORMATION DISCLOSED ON THIS DOCUMENT IS CONSIDERED PROPRIETARY AND SHALL NOT BE |
REVISION DATE : |
|
|||||
|
|
|
|
|
22-OCT-18 |
|
||||||
ADDED CRITICAL REQUIREMENT #4 IN PAGE 3 & 4. |
|
INCHES |
mm |
REPRODUCED OR DISCLOSEDWITHOUT WRITTEN CONSENT OF NIDEC MOTOR CORPORATION |
|
|
||||||
|
|
|
.XX = ± .010 |
|
TITLE |
CODE |
ITEM NO. |
REV |
|
SHEET |
|
DWG |
|
|
|
.XXX = ±.005 |
|
CUSTOMER DETAIL DRAWING |
|
|
E |
|
NUMBER |
|
SIZE |
ISSUED BY : |
ENGINEER APPROVED : |
|
|
|
V02 |
802884 |
|
|
|
B |
||
I. GUTIERREZ |
S. SCHINZING |
|
|
|
1 OF 6 |
|
||||||
ANGLES X°= ±1° |
|
|
||||||||||
V02_NMCB (MAR-2014) |
SOLIDEDGE |
Loading...