VAR |
MODEL |
CUSTOMER |
CAT. NO. |
A |
B |
XN |
THP |
VOLTS |
AMPS |
HZ |
RPM |
PREM. EFF. LABEL |
CALIFORNIA TITLE 20 LABEL |
DESCRIPTION / REMARKS |
|||
001 |
B63GZABL-1032 |
POOL AFTERMARKET |
ASB2980 |
13.71 |
12.99 |
5.28 |
1.25/0.20 |
230 |
5.8/1.2 |
60 |
3450/1725 |
YES |
COMPLIANT |
2 CAPACITOR COVER MOUNTING SCREWS |
|||
002 |
B63GZABM-1033 |
POOL AFTERMARKET |
ASB2982 |
13.96 |
13.24 |
5.28 |
1.65/0.26 |
230 |
7.4/1.4 |
60 |
3450/1725 |
YES |
COMPLIANT |
2 CAPACITOR COVER MOUNTING SCREWS |
|||
003 |
B63GZABN-1034 |
POOL AFTERMARKET |
ASB2983 |
14.46 |
13.74 |
5.51 |
2.25/0.38 |
230 |
9.2/2.1 |
60 |
3450/1725 |
YES |
COMPLIANT |
4 CAPACITOR COVER MOUNTING SCREWS |
|||
004 |
B63GZABP-1035 |
POOL AFTERMARKET |
ASB2984 |
14.96 |
14.24 |
5.51 |
2.60/0.43 |
230 |
10.6/2.4 |
60 |
3450/1725 |
YES |
COMPLIANT |
4 CAPACITOR COVER MOUNTING SCREWS |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
REV. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A ±.060
(6.6) |
B |
|
PREMIUM EFFICIENCY LABEL |
|
|
|
|
|
|
.406 ±.005 |
|
|
|
|
|
|
||||
(PER CHART ABOVE & BOM) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GROUND LUG
NAMEPLATE
(XN)
TOP
-A-
TOP
.6250
.6245
1/2-14 NPT CONDUIT |
|
|
|
HOLE WITH PLUG |
|
|
|
REV. |
|
|
|
C |
SERIALIZED LABEL |
|
|
|
n A .006 |
||
CALIFORNIA |
(POOL AFTERMARKET) |
||
|
|||
TITLE 20 LABEL |
|
n A .006 |
|
|
AQUA SHIELD LABEL |
||
|
|
||
NOTE: |
1/2-20 UNF-2A R.H. THREAD |
||
1. 300 SERIES STAINLESS |
|||
|
|
||
STEEL SHAFT EXTENSION. |
|
THREAD PROTECTOR |
|
ROTATION : CW LEAD END |
|
||
|
|
||
NIDEC MOTOR CORPORATION 04-Oct-18 |
|
|
|
7.125 DIA. BOLT CIRCLE
5.750 +.002 -.000
a A .006
45°
45°
WATER |
SHAFT |
4 HOLES |
|
SLINGER |
SEAL |
||
.406 DIA. |
|||
|
|
||
|
6.5 |
|
1/4-20 UNC-2B
INTERNAL L.H. THREAD
.625 DEEP MIN.
REFER TO S.E.I.M. 24-1
|
REVISION RECORD FOR: |
E32395 |
TOLERANCES ON DIMENSIONS |
NIDEC MOTOR CORPORATION |
|
|
|
||||||||
CALIFORNIA TITLE 20 LABEL ADDED. |
|
(UNLESS OTHERWISE SPECIFIED) |
|
|
|
||||||||||
|
|
|
|
|
|
|
|||||||||
COMPLIANT COLUMN ADDED. |
|
|
|
|
|
|
|
|
|
INFORMATION DISCLOSED ON THIS DOCUMENT IS CONSIDERED PROPRIETARY AND SHALL NOT BE |
REVISION DATE : |
|
|||
|
|
|
|
|
|
|
|
|
|
04-OCT-18 |
|||||
|
|
|
|
|
INCHES |
|
mm |
REPRODUCED OR DISCLOSEDWITHOUT WRITTEN CONSENT OF NIDEC MOTOR CORPORATION |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
.XX = ± .010 |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
TITLE |
CODE |
ITEM NO. |
REV |
SHEET |
DWG |
|||
|
|
|
|
.XXX = ±.005 |
|
|
|
CUSTOMER DETAIL DRAWING |
|
|
|
NUMBER |
SIZE |
||
ISSUED BY : E. REYES |
|
ENGINEER APPROVED : S. SCHINZING |
|
|
|
|
|
V02 |
805809 |
C |
1 OF 4 |
B |
|||
|
ANGLES X°= ±1° |
||||||||||||||
V02_NMCB (MAR-2014) |
SOLIDEDGE |
Loading...