INSTRUCTION MANUAL
FAN HEATER
Model- FH 3212 PTC
Dear Customer,
Congratulations!
You are now the proud owner of Usha Fan Heater FH 3212 PTC
Innovatively designed, using only the highest quality material and
components, your Usha Fan Heater FH 3212 PTC is designed for
years of trouble free performance.
Please read this Instruction Manual carefully before using and keep
it cautiously after reading for future reference.
Best Wishes
IMPORTANT PRECAUTIONS
• Read all instruction carefully and keep this manual for future reference.
Please use suitable voltage and frequency (220-240V AC, 50Hz).
• Please consider the load capacity of your home electricity when you start to use
this unit.
• Do not put additional device on the unit.
• Do not impinge or shake the unit when it is in operation.
• Do not use the unit under direct sunshine.
• Do not touch the wind outlet when operating to avoid scalding skin.
• Please keep wind inlet and outlet unblocked to avoid any fire and malfunction
appearance, such as distortion, changing color etc.
• Please put the power cord in right place in order to avoid tripping the unit over.
• Do not let power cord touch wind outlet. It will damage the insulation layer of
wires.
• Please place unit on flat and stable table or floor when operation. Do not use it
in bathroom or similar places.
• Avoid using of extension cords because the extension cord may overheat and
cause a risk of fire. Never use a single extension cord to operate more than one
heater.
• Forbid to put flammable and explosive objects around unit, and do not use unit
in an environment full of flammable gas and powder.
• Ensure no water or raindrop into the unit, in order to avoid electric shock. Do not
put flammable objects or damp clothes on the wind outlet in order to avoid short
circuit or fire.
• Please do not place wind inlet or outlet near to curtain or wall when operation or
it will block air current and cause a risk of fire.
• Please do not insert conductor bar into wind inlet or outlet, in order to avoid
electric shock.
• Please turn off the unit when not in use, otherwise it may result in danger.
• This appliance is not intended for use by people (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they receive supervision or instruction concerning use of
the appliance by keeper.
• Please unplug before cleaning or maintenance.
• Clean the surface of the unit with damp cloth (or add some detergent). Do not
use corrosive detergent or solvent to clean. Not allowed to wash with water.
Make sure the unit dry enough before use it again.
• Please unplug the unit when not in use, and make sure power is off before
pulling out the plug.
• When not in use for long time, please pull out the plug, pack the unit well and
stock in dry environment.
• With any indication of malfunction, contact service center for repairs. Do not
attempt to disassemble the product or replace faulty parts with unauthorized
components. Because it will damage the unit.
• Please bring the unit to the Usha authorized service center for repairs.
• Children should be supervised to ensure that they do not play with the
appliance.
• Warning: in order to avoid overheating, do not cover the heater by clothes or
paper.
• Do not use this heater in the immediate surrounding of a bath, a shower or a
swimming pool.
• If the supply cord is damaged, it must be replaced by the Usha authorized
service center.
• The heater must not be located immediately below a socket outlet.
PRODUCT FEATURES
• PTC Heating Element for Extra Safety and Power Saving
• Two Heating Positions
• Adjustable Thermostat
• Oscillation Function
• Handle for Portability
• Inbuilt Tip over switch for safety
• Two Metre Long Power Cord
• ISI Mark
PARTS DESCRIPTION
• Product appearance
• Product structure
1. Handle 8. Base
2. Handle dowel 9. Bottom cover
3. base of Handle 10. Swing base
4. Temperature adjusting knob 11. Swing switch
5. Head cover 12. Back cover
6. Power setting knob 13. Power line jacket
7. Wind out-let grill 14. Power line
• Display and operation panel
OPERATION INTRODUCTIONS
• Installation
n Take the devices out of packing,
n Put the master device on a desktop, as showed below;
• Switch function
n Make sure the voltage and frequency is complied with the technical
parameters (220V-240V AC, 50Hz), then connect the power.
n Using instruction
1. Power setting knob
ä Counter-clockwise rotate the knob to "COOLER", then the PTC element will
not work, and only function as fan.
ä Rotate the knob to "OFF", then the device stop working.
ä Clockwise rotate the knob to "LOW", then the device start working in lower
power situation.
ä Clockwise rotate the knob to "HIGH", then the device start working in high
power situation.
Attention: If the knob turns to "HIGH" position, then can not clockwise rotate
anymore. Otherwise, it will damage the knob, and affect the function.
2. Temperature adjusting knob
ä Clockwise rotate the knob to the temperature that you want to set, then the
indoor temperature will rise along with the working of the device.
ä The device would keep the setting temperature automatically when in
operation. If the indoor temperature reaches the setting temperature, then
the device will enter into power off status. If the indoor temperature is lower
than setting temperature, the device will start work automatically.
ä Temperature adjusting knob should be rotated in the effective range. If out
of the range, then it will damage the knob, and affect the function.
3. Swing switch
ä Press swing switch, the device will start oscillation. Press this switch again,
then it will stop oscillation.
CLEANING AND MAINTENANCE
• Before maintenance, please pull off the plug and let the fan cool down;
• If there have dirty in the face, you can use a soft fabric to clean it; if the dirty in
large area, you can use water below 50 degree and neuter scour to wash it, and
use soft fabric to dry it.
• Do not use gas, thinner and any others which can destroy the surface.
• You should make the fan cool and dry, then packed well and stored in ventilated
condition.
PRODUCT SPECIFICATION
Model No. FH 3212 PTC
Rated voltage 220-240V AC
Frequency 50Hz
Wattage Low/ High 1200W / 2000W
WARRANTY CARD
This Fan Heater is warranted for one year against all manufacturing defects
from the date of sale. In the event of any complaint, please contact your
nearest Company Service Centre or call at our Toll Free no: 1800-1033-111
This Warranty is valid only when…
1. The Fan Heater has not been opened or tempered with, by any
unauthorized person.
2. The warranty card or cash memo duly signed by the authorized dealer
are presented with the complaint.
3. The Fan Heater has been installed, used and maintained in accordance
with the instructional manual.
This Warranty does not apply for…
1. Damages due to chipping, peeling, plating and denting.
2. Breakage or damage to components made out of Bakelite, Urea, ABS,
SAN and such plastic, materials, rubber parts and cord.
3. Normal wear and tear of parts.
4. Damage resulting from accidents, mishandling or negligence on part of
the customer.
Liability for consequential loss or damage is neither accepted nor implied.
S.NO: _____________________________________________________
CASH MEMO _______________________DATE: _________________
DEALER'S NAME AND ADDRESS: _______________________________
__________________________________________________________
OWNER'S NAME & ADDRESS: __________________________________
___________________________________________________________
Loading...