U.S. General 93663 Assembly And Operating Instructions Manual
Professional CordlessProfessional Cordless
Professional CordlessProfessional Cordless
Professional Cordless
LED W LED W
LED W LED W
LED W
ork Lightork Light
ork Lightork Light
ork Light
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
93663
Due to continuing improvements, actual product may differ slightly from the product described herein.
SKU 93663
For technical questions please call 1-800-444-3353
Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Keep work area well lit. Do not use electrically
powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not
let them handle machines, tools, or extension cords.
4. Store idle equipment. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not modify this tool and do not use this tool for
a purpose for which it was not intended.
6. Dress properly. Protective, electrically nonconductive clothes and nonskid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles
when working with tools or equipment.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines.
:noitcurtsnoC
citsalpomrehTfoorprettahS
.gnitaocrebburhtiwesac
:sthgiL
rotcelferhtiwsthgilDEL)03(
sttaW04o
ttnelaviuqe
:rewoP
dCiNhA0.3-V8.4
yrettabelbaegrahcer
:yticapaC
fosruohsuounitnoc6otpu
yrettabdegrahcyllufh
tiwesu
:tinUregrahCzH06CAV021sesU:emitefiLDELsruoh000,001yletamixorppA
:snoisnemiDD"2xW"4/1-2xH"8/1-11:thgie
WteN.sbL08.1
SKU 93663
For technical questions please call 1-800-444-3353
Page 3
9. Maintain tools with care. Keep tools maintained and clean for better and safer
performance. Inspect tool cords periodically and, if damaged, have them repaired
by a qualified technician. The handles must be kept clean, dry, and free from oil
and grease at all times.
10. Disconnect power. Unplug battery charger when not in use.
11. Stay alert. Watch what you are doing, use common sense. Do not operate any
tool when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform
its intended function. Any part that is damaged should be properly repaired or
replaced by a qualified technician. Do not use the tool if any switch does not turn
On and Off properly.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
15. Use proper size and type extension cord. If an extension cord is required, it
must be of the proper size and type to supply the correct current to the tool
without heating up. Otherwise, the extension cord could melt and catch fire, or
cause electrical damage to the tool. This tool requires use of an extension cord
of 0 to 10 amps capability (up to 50 feet), with wire size rated at 18 AWG. Longer
extension cords require larger size wire. If you are using the tool outdoors, use
an extension cord rated for outdoor use (signified by “WA” on the jacket).
16. Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
Note: Performance of the battery charger may vary depending on variations
in local line voltage. Extension cord usage may also affect tool performance.
Warning: The warnings, cautions, and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that common sense
and caution are factors which cannot be built into this product, but must
be supplied by the operator.
Loading...