U.S. General 92687 Assembly And Operating Instructions Manual
Engine Oil PressureEngine Oil Pressure
Engine Oil PressureEngine Oil Pressure
Engine Oil Pressure
TT
TT
T
esterester
esterester
ester
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright© 2005 by Harbor Freight Tools®. All rights reser ved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
92687
SKU 92687
For technical questions, please call 1-800-444-3353
Page 2
Specifications
Save This Manual
You will need the manual for the saf ety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover.
Keep the manual and in v oice in a safe and dry place for future ref erence .
Safety Warnings and Precautions
W ARNING: When using tool, basic safety precautions should al ways be follo wed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp
or wet locations. Don’t expose to rain. Keep work area well lighted. Do not
use electrically powered tools in the presence of flammable gases or liquids.
Be aware of the inherent dangers of working on a gasoline engine.
3. Keep children away. Children must never be allowed in the work area. Do
not let them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry location
to inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. This oil pressure tester is intended for use on
automotive and truck engines. Do not modify this tool and do not use this tool
for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught
in moving parts. Protective, electrically nonconductive clothes and nonskid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair . Wearing a long-sleev e shirt and long pants are recommended
while working.
7. Use safety equipment for your protection. Always wear ANSI approved impact
safety glasses underneath a full face shield along with heavy work gloves when
working on gasoline engines. Be sure to work in a well-ventilated place.
:noitcurtsnoC
,esoHrebbuR,esaCcitsalP
sgnittiFssarB
:elacSerusserP
ISP001-0
RAB7.0-0
:gnittiFeguaGTPN81-"4/1:eziSesoHgnoL"42x"4/1
lanoitiddA
:sgnittiF
TPN81-"4/1xTPN72-"8/1
TPN81-"8/3xTPN72-"8/1
:thgieWteN.bL7.0
Note: Accuracy of the Gauge is ± 2%.
REV 05/05
SKU 92687
For technical questions, please call 1-800-444-3353
Page 3
8. Carbon Monoxide W arning: Guard against exposure to Carbon Monoxide, which
is an odorless, colorless gas produced by gasoline engines. Carbon Monoxide
exposure may cause serious injury or death.
9. Do not overreach. K eep proper f ooting and balance at all times. Do not reach
over or across running machines. Do not allow this tester to interfere with the
moving parts of a running engine.
10. Maintain tools with care. K eep tester threads sharp and clean for better and
safer performance. Follow instructions for maintenance and changing
accessories. The gauge hose and adapters must be kept clean, dry, and free
from oil and grease at all times.
11. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Any part that is damaged should be properly
repaired or replaced by a qualified technician. Do not use the tester if it leaks
or the gauge does not function properly.
13. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
14. Maintenance. F or your saf ety, service and maintenance should be performed
regularly by a qualified technician.
WARNING: The brass components of this product contain lead, a chemical
known to the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code § 25249.5,
et seq.
)
W ARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that ma y occur.
It must be understood b y the operator that common sense and caution are factor s
which cannot be built into this product, b ut must be supplied b y the operator .
Unpacking
When unpacking, check to mak e sure the following parts are included.
Oil Pressure Gauge with Extension Hose
(2) Adapters
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
Loading...