Universal Remote Control UR3-SR3, OCE-0009D User Manual

Universal Remote Control, Inc.

www.universalremote.com

UR3-SR3

Operating Manual

For Easy Clicker

1

This remote control is designed to operate most Digital
and Analog Cable Boxes, as well as TVs, and a VCR or
DVD player.

Introduction

Install two

AAA alkaline batteries

as shown here

1

Before you program or operate the remote control, you
must install two new AAA alkaline batteries.

STEP1 Remove the battery compartment cover from the

back of your remote control.

STEP2 Check battery polarity carefully, and install the

batteries as shown in the illustration below.

STEP3 Replace the battery compartment cover.

Replacing Batteries

2

32

STEP1 Turn on the equipment that you want the remote

control to operate Cable Box, TV and DVD(VCR).

STEP2 Press the [DEVICE] button and the [OK/SEL]

button simultaneously for three seconds. The
corresponding device LED will turn on indicating
that it is ready to be programmed. The LED will
remain on for 20 seconds. The next step must be
entered while the LED is on.

STEP3 Point the remote control toward the equipment

and enter the three-digit code number assigned
to your brand from the code tables. If there are
more than one three-digit number listed for your
brand, try one code number at a time until your
equipment turns off.

*Note : You can verify that you have selected the correct

code by pressing the [MUTE] button. The
equipment should turn on or off.

STEP4 Store the three-digit code by pressing the same

[DEVICE] button once again. The device LED will
blink twice to confirm that the code has been
stored.

*Note : Try all the functions on the remote control. If any

of the functions do not operate as they should,
repeat the instructions from Step 2 using the next
three-digit code number from the same brand list.

B. Auto Sear

B. Auto Sear

ch Method

ch Method

If none of the three digit code numbers assigned to your
brand of equipment works, or the code table does not list
your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by
following steps:

STEP1 Turn on the equipment that you want the remote

control to operate (Cable Box, TV, VCR, or DVD).

Button Functions

3

Programming the Remote Control.

4

A. Manual Pr

A. Manual Pr

ogramming

ogramming

The remote control can be programmed by entering a three­digit code number that corresponds to particular brands and
models of equipment. The three-digit code numbers are listed
in the code tables sections of this instruction manual.

*Note : In this section, when you are instructed to press a

[DEVICE] button, that means you should press either
the CBL, TV, or DVD button, depending on which
device you are programming the remote to operate.

54

simultaneously for 3 seconds. The DVD LED will
turn on for 20 seconds. The next step must be
performed while the LED is on.

STEP2 Press the [TV] button.

STEP3 Point the remote control toward the TV and enter the

three-digit code for your TV from the TV codes table.

STEP4 Store the three-digit code by pressing the [DVD]

button. The device LED will blink twice to confirm
that the code has been stored.

E. Pr

E. Pr

ogramming for Advanced Functions.

ogramming for Advanced Functions.

In the CABLE device mode, the A,B,C,D and blank macro
buttons can be programmed to act as a 'Macro' or
Favorite Channel button. This allows you to program up to
five 2-digit channels, four 3-digit channels or three 4-digit
channels that can be accessed with on button press.

*Note : The A,B,C and D buttons are not programmable

if you have a Digital Cable Box made by Pace,
Pioneer or Scientific-Atlanta.

STEP1 Press the [CBL] button to select the CBL mode.

STEP2 Press the [MACRO] button and [OK/SEL] button

simultaneously for 3 seconds. The [CBL] button
will turn on for 20 seconds.

STEP3 Enter the the 2, 3 or 4-digit code for the channel you

want programmed first (for example, 007) using the
Number Pad, then press the [STOP] button. Then
enter the code for the next channel (for example,

050), then press the [STOP] button. Repeat this
process for the third channel. The [CBL] button will
blink once for each channel entered.

STEP4 Press the [CH+] button to store the channels that

were selected. The [CBL] button will blink twice
to confirm the storage of commands.

STEP2 Press the [DEVICE] button and the [OK/SEL]

button simultaneously for three seconds. The
device LED will turn on indicating that it is ready
to be programmed. The LED will remain on for 20
seconds. The next step must be entered while
the LED is on.

STEP3

Press the [CH+] or [CH-] button one at a time or
keep it pressed. The remote will emit a series of
Power ON/OFF code signals. Release the [CH+] or
[CH-] button as soon as the equipment turns off.

*Note : You can verify that you selected the correct code

by pressing the [MUTE] button. The equipment
should turn On or Off.

STEP4 Press the same [DEVICE] button to store the

code. The Device LED will blink twice to confirm
that the code has been stored.

C.

C. TT

o find the Thr

o find the Thr

ee-Digit Code that W

ee-Digit Code that Wasas

PrProgrammed using the Auto Sear

ogrammed using the Auto Searchch

Method

Method

STEP1 Press the appropriate [DEVICE] button and the

[OK/SEL] button simultaneously for three
seconds. The device LED will turn on for 20
seconds. The next step must be performed while
the LED is on.

STEP2 Press the [INFO] button. The device LED will blink

a number of times indicating the number of each
digit for the code. Each digit is separated by a
one second interval of the LED being off.

Example : One blink, then three blinks, then eight blinks

indicates the code number 138.

*Note : Ten blinks indicates the number 0.

D.

D. PrPr

ogramming a Second TV to the DVD Button

ogramming a Second TV to the DVD Button

STEP1 Press the [DVD] button and the [OK/SEL] button