Universal Electronics UNI2 User Manual

UNI-335

LCD Display 2-Way Alarm & Starter

OPERATION MANUAL

UNI1:1-Way Remote Control UNI2: LCD REMOTE CONTROL TRANSCEIVER

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system isthe sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.

10.It is not safe to remote start the vehicle if the vehicle is p arked on a steep incline.

1-Way Remote Control: UNI1

LCD REMOTE CONTROL TRANSCEIVER: UNI2

A. BATTERY REPLACEMENT:

This system needs no specific maintenance beyond remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a pair of 3V, CR2016 batteries.

Battery Level Indicator (2-way remote)

The Battery Level indicator has three level indicators that serve as a visual indication of battery charge. When the battery reaches a low charge level that requires replacement, the remote control will generate a single notification chirp, and the Battery Level

indicator

will flash continuously.

Gently pull the end of the battery door away from the top of the remote control then slide the door up to expose the battery and remove the expired battery. Place the new battery into the remote. When power is returned the rem ote control will display all icons in the LCD and generate all beeper tones once. Press any button on the remote to terminate the beeper tone review.

B. STANDARD LCD ICON CONFIGURATIONS:

The lock icon will be displayed when the door locked.

Sensor Bypass

Sensor 1 bypass under Arm mode

Valet Mode

Remote start and alarm functions shall be temporarily on hold.

Hood Trigger

Hood is illegally opened (Zone

Door Open Warning

Doors are illegally opened (Zone 3)

Ignition Trigger

Ignition switch is illegally turned on (Zone5)

Remote Transmission

You are transmitting the signal to control unit

Anti Car-Jack Mode

Activate the anti car-jacking mode

Engine Cranking

Your vehicle engine

The unlock icon will be displayed when the door unlock

Hidden Alarm Mode The security system arm with

hidden alarm function (silent alarm)

Trunk Trigger

Trunk is illegally opened (Zone 2)

Sensor Trigger

Trigger on Sensor 1 (Zone 4)

System trigger

In – Range Indicator

You are within the range of the remote control.

Icon flash under check mode

Engine Running

Your vehicle's engine is

Cranking by remote

running

control

Timer Control Start

Engine start automatically every 2 or 3 hours.

Daily Start

Engine start automatically at the same time next day

Temperature Start

Engine start automatically when reach

Turbo Timer

Turbo timer was set up

programmed temperature.

Manual Gear

Engine Start Memorizing for the car with manual gear was set up

Activate Channel 3

Activate Channel 3 (Trunk Release).

Activate Channel 4

12:00 Time Monitor 12:00 Alarm Clock

You have set morning call alarm

Parking Meter

Reminder when time is up for parking

Melody Mode

Remote Control alert user through melody sound

Low Battery

You have to replace the battery of remote control.

Vibration Mode

Remote Control vibrates when the system is triggered

OPERATION:

C: REMOTE TRANSMITTER OPERATION:

Transmitter Button

+ +

System Function Remark

Lock Doors & Arm System Panic function Press and Hold for 3 seconds .

Press Trunk panic function

Car Locator Press when in armed mode Arm and Delete The 2 Stage Shock

Sensor

Press twice within 3 seconds. Pass will appear

on the remote

Arm System and Hidden Alarm Function Press within 3 seconds and

Hold

Silent Arming / Disarming Ignition in "off" position. Active Anti Car-Jacking Mode Ignition in "on" position press

and hold for 2 seconds

button to stop

button for 2 seconds

Unlock Doors & Disarm System Two Steps Door Unlock & Disarm

System(optional) Trunk Release (Channel 3) Passive

Arming By-pass

Press twice within 3 seconds.

Press and Hold for 2 seconds While the system Disarmed.

Activate or Turn Off The Remote Start Press button once.

Press Twice if set to

start safety mode

Channel # 4 Timer Output (4) Optional

D CHIRP INDICATORS: PARKING LIGHT:

Chirp Function Parking Function 1 chirp Arm 1 flash Arm 2 chirps Disarm 2 flashes Disarm 3 chirps Defective Reminder 3 flashes Disarm / Triggered 4 chirps Disarm/ Triggered 6 flashes Car Locator 6 chirps Car Locator Constant On Under Remote Start

ALARM OPERATING CONDITION:

Siren/ Horn Parking Light LED Doors Starter Dome

1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disable

2.Disarming 2 or 4 Chirps 2or 3 Flashes

3. Trigger Alarming Flashes Slow Flash Disable Flashes

4. Passive

Starter Disable

Fast Flash Disable

5. Panic Alarming Flashes

6.Car-Jacking Alarming Flashes

7. Car Locator 6 Chirps 6 Flashes Locking

Unlocking

Flashes

Disable Flashes

Turns on for 30-second

E. ACTIVE ARMING – LOCK & ARM:

1.Press button on the transmitter.

2.The siren will chirp once and parking light will flash once indicating that the system is

now armed. The vehicle’s doors will lock upon arming if interfaced with the security

system. DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.

SILENT ARMING / DISARMING: Press the transmitter time. This will arm or disarm your security system, No chirp sound will be heard, arm /

disarm confirmation will be through thevehicles parking lights only.

SENSOR BY-PASS:

The sensor bypass feature is programmed to activate for one arming cycle only. The

and buttons at the same

security system will return to normal operation during the next arming cycle.

Sensor By-Pass :Press the system and by-pass the shock sensor.

HIDDEN ALARM FUNCTION:Silent Alarm

Press the alarm function. The security system will arm and with “Hidden Alarm Function” The siren /

horn will be silenced even if the sensor is triggered in the armed status. Alarm indication will only appear on the LCD Transmitter.

button first; within 3 seconds press the button to activate the hidden

button two times within 3 seconds will arm the security

F. PASSIVE ARMING (Programmable)

Active arming / disarming is controlled by your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If

you reopen anydoor / hood / trunk, the security system LED will stop flashing. It will

begin flashing again once all vehicleentrances are closed.

3. After the 30-second time has elapsed, the security system will automatically “ARM”.

The siren will chirp [1]time and the parking lights will flash [1] time.

PASSIVE ARMING WITH PASSIVE DOOR LOCKING

The vehicle doors will automatically lock after the passive arming cycle has been completed. PASSIVE ARMING BY -PASS: While the system is disarmed, Press the the system will respond with [1] chirp and LED will turn “ON”. The security system will remain in this temporary state for as long as you wish.

button twice,

To exit passive by-pass, press the transmitter to normal status.

or buttons and the system will return

G. ACTIVE DISARMING – UNLOCK & DISARM:

1. Press button on the transmitter.

2. The siren will chirp twice and the parking lights will flash twice indicating that the

security system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door locks and dome light

must be installed with the security system.) TAMPER DISARMING : If the alarm is triggered, upon disarm the system’s siren will chirp 4 times, and the parking lights will flash 4 times telling you the alarm has been triggered during the last armed state. P ATHWAY ILLUMINA TION: When receiving an unlock /disar m signal, this feature will turn the parking lights“ON” for 30 seconds and for 10 seconds upon the lock signal. (Programmable) TWO STEPS DOOR UNLOCK (Optional): This feature will independently unlock the

driver’s door only when disarming the security system. Pushing the button a second time within 3 seconds will unlock the other doors. AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed.

H. DISARMING WITHOUT A TRANSMITTER

OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default

Setting)

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to the 'ON’ position.

2. (Alarm will sound.)

3. Within 10 seconds push and release the valet switch. The alarm will stop sounding and

enter the disarm mode. You can now start and operate the vehicle normally.

OVERRIDE THE ALARM WITH PASSWORD PIN CODE:

Unlike valet switch that can easily be found and defeated, this security system allows the consumer to program a password pin code offering a higher level of security.

1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)

2. Within 5 seconds, enter your chosen first digit code by pressing and releasing the Valet

Switch. 3. Within 15 seconds of the last digit code enter (the 1st code), then turn the Ignition Switch “OFF” and then“ON”.

4. Within 15 seconds, enter your chosen second digit code by pressing and releasing the

Valet Switch.

5. Turn the ignition switch “OFF” position. 4 Chirps from siren/horn and 4 flashes from the

parking light indicate the system has disarmed.(When finished above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle can’t be

started.) Note:You must override the alarm within 60 seconds. If not, the system will automatically re-arm.

EXAMPLE: To Override the System with the Password Code 83,

1. Enter the vehicle and turn the ignition switch to the 'ON’ position.(Alarm will sound.)

2. Within 5 seconds, Press and Release the Valet Switch 8 times,

3. Within 15 seconds of entering the last digit code enter (the 1 Switch “Off” and then“ON”.

4. Within 15 seconds, Press and Release the Valet Switch 3 times.

5. Turn the Ignition Switch to the “Off” position. 4 Chirps form siren/horn and 4 flashes from the parking lights will indicate the system has disarmed.

code), turn the Ignition

I. VALET MODE:

VALET MODE: (System is in Disarm Mode )

The valet switch allows you to temporarily bypass all alarm function, eliminating the

need to hand your transmitter to parking attendants or garage mechanics. When the

+ 14 hidden pages