Page 1
DESK
Thank you for purchasing the DESK！！！！
B
efore you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
Hardware:
a
c
e
g
j
m
m
C
am x30
Sc
rew M4x35mm x12
Pull x2
Screw M4x14mm x30
Knob x2 k
Bolt M6x50mm x2
Leveler x4
Page 1 of 8
b
d
f
h
n
p
Pu
ll Screw M4x20mm x6
Drawer Guides x3 sets
Bolt M6x12mm x12
Drawer Bottom Holder x6
C
am Post x30
Dowel x32
Allen Wrench x1
Page 2
DESK
F
B
M
K
H2
H4
H
H1
H5
L
K
A
J2 J3
3
J4
J5
J1
D
G
P
H
E
H2
4
H1
C
H3 H
H5
N
Component:
A
C
E
G
H2
H4
J1
J3
J5
L
N
Top Panel x1
Right Side Panel x1
Right Divide Panel x1
Center Bottom Panel x2
Side Left Drawer Side x2
Side Drawer Back x2
Center Drawer Front x1
Center Right Drawer Side x1
Center Drawer Bottom x1
Center Back Panel x1
Right Leg x1
Page 2 of 8
B
D
F
H1
H3
H5
J2
J4
K
M
P
Left Side Panel x1
Left Divide Panel x1
Left Bottom Panel x1
Side Drawer Front x2
Side Right Drawer Side x2
Side Drawer Bottom x2
Center Left Drawer Side x1
Center Drawer Back x1
Side Back Panel x2
Left Leg x1
Bottom Rail x1
Page 3
DESK
HOW TO USE CAN AND CAM POST HARDWARE
1. 2
3.
5.
.
4
.
Turn cam clockwise
1
/2 turn
Note cam arrow
d
irection
Note cam arrow
d
irection
S
TEP 1:
Pl
ace 1pc Side Drawer Front (H1),1pc Side Drawer Back (H4),1pc Left Drawer Side (H2), 1pc Right Drawer Side (H3)
and 1pc Side Drawer Bottom (H5) together as shown.
Attach them by 2pcs Cam Post (a), 2pcs Cam (b), 4pcs Screw (c), tighten the Screws (c) and Cam (b)
Attach 1pc Pull (e) to the Side Drawer Front (H1) by using 2pcs Pull Screw (d).
Fully tighten Cams (b), Screws (c), Pull Screws (d) with Phillips Head Screw Driver (not included).
Repeat the same steps and hardware for the other Side Drawer.
H3
a
b
c
H4
H5
d
h
d
a
b
e
H
1
c
H2
ax4 bx4 cx8
dx4
ex2
Page 3 of 8
Phillips Head Screwdriver
( not included)
Hardware & Tools required
Page 4
DESK
S
TEP 2:
Place 1pc Center Drawer Front (J1),1pc Center Drawer Back (J4),1pc Center Left Drawer Side (J2),
1pc Center Right Drawer Side (J3) and 1pc Center Drawer Bottom (J5) together as shown.
Attach them by 1pc Cam Post (a), 1pc Cam (b), 4pcs Screw (c), tighten the Screws (c) and Cam (b)
Attach 2pcs Knob (e) to the Center Drawer Front (H1) by using 2pcs Pull Screw (d).
Fully tighten Cams (b), Screws (c), Pull Screws (d) with Phillips Head Screw Driver (not included).
J3
b
e
a
d
j
J1
J4
e
J5
b
d
a
j
J2
ax2 bx2 cx4
STEP 3:
Pl
ace the assembled Center Drawer upside down on a carpeted or padded surface.
Attach the 6pcs Drawer Bottom Holder (n) to the bottom of the assembled Center Drawer by using 6 pcs Screw (g) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Screws (b) clockwise until secure.
dx2
jx2
Phillips Head Screwdriver
( not included)
Hardware & Tools required
gx6 nx6
J2
n
Phillips Head Screwdriver
( not included)
Page 4 of 8
g
g
J1
g
J5
J4
n
g
g
n
J3
Hardware & Tools required
Page 5
DESK
STEP 4:
Place the Left Side Panel (B), Right Side Panel (C), Left Divide Panel (D) and Right Divide Panel (E) upside down
on a carpeted or padded surface.
Attach the 3 sets Drawer Guides (f) to the Left Side Panel (B), Right Side Panel (C), Left Divide Panel (D) and
Right Divide Panel (E) by using 12pcs Screw (g) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Screws (g) clockwise until secure.
g
f
C
C
g
g
g
g
g
E
g
g
g g
g
D
g
B
g
g
f
C
fx3 gx12
S
TEP 5:
Insert 20pcs Cam Post (a) into the corresponding holes on the Top Panel (A), Left Divide Panel (D) , Right Divide Panel
(E), Left Bottom Panel (F) and Right Bottom Panel (H) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Cams (a) clockwise until secure.
Insert 26pcs Dowel (h) into the corresponding holes on the Top Panel (A), Left Divide Panel (D) , Right Divide Panel (E),
Left Bottom Panel (F) and Right Bottom Panel (H) as shown.
Phillips Head Screwdriver
( not included)
Hardware & Tools required
E
a
a
h
a
h
h
a
h
h
a
ax20 hx26
h
a
h
h
a
h
h
a
Phillips Head Screwdriver
( not included)
D
h
a
h
h
a
F
a
h
h
h
a
a
a
h
h
h
h
a
a
H
h
a
a
h
h
h
h
h
a
a
A
Hardware & Tools required
Page 5 of 8
Page 6
DESK
STEP 7:
Place the Left Divide Panel (D), Right Divide Panel (E) and Center Back Panel (L) to the Center Bottom Panel (G) as shown.
Attach them by using 12pcs Cam (b) and 2pc Dowel (h).
Use Phillips Head Screwdriver (not included) to tighten the Cams (b) clockwise until secure.
b
D
b
E
b
h
G
b
h
L
b
S
TEP 8:
Place the Left Side Panel (B), Right Side Panel (C), Side Back Panel (K) and the Assembled Left Divide Panel (D),
Right Divide Panel (E), Center Back Panel (L) to the Top Panel (A) as shown.
Attach them by using 8pcs Cam (b) .
x4
hx2
Phillips Head Screwdriver
( not included)
Hardware & Tools required
Use Phillips Head Screwdriver (not included) to tighten the Cams (b) clockwise until secure.
C
K
b
E
G
b
b
L
A
b
x8
Phillips Head Screwdriver
( not included)
Hardware & Tools required
b
D
b
K
B
b
Page 6 of 8
Page 7
DESK
STEP 9:
Please put Assembled Top Panel(A1&A2) upside down on a carpeted or padded surface.
Place the Bottom Panel (B) to the assembled Side Panels (C&D),
Attach them by using 12pcs Bolt (j).
Use Allen Wrench (q) to tighten the Bolts (j) clockwise until secure.
, Divide Panels (E&F) and Back Panel (G) as shown.
, ,
F
h
h
b
b
C
bx8
S
TEP 10:
Place the L
Attach them by using 2pcs Bolt (m).
Use Allen Wrench (p) to tighten the Bolts (q) clockwise until secure.
K
h
x4
eft Leg (M), Right Leg (N) and Bottom Rail (P) upside down on a carpeted or padded surface as shown.
E
Phillips Head Screwdriver
( not included)
G
E
h
b
D
b
K
Hardware & Tools required
h
b
b
B
p
m
mx2 px1
M
p
m
P
N
Hardware & Tools required
Page 7 of 8
Page 8
DESK
STEP 10:
Please put the assembled desk’s top upside down on a carpeted or padded surface as shown .
Attach assembled Left Leg (M) and Right Leg (N) into the bottom of the Left Bottom Panel (F) and Right Bottom
Panel (H) by using 12pcs Blot (k).
Use Allen Wrench (p) to tighten the Bolts (k) clockwise until secure.
m
m
m
P
N
p
M
J
m
H
kx12 px1
STEP 11:
Pull out the 3 sets metal drawer guides of Drawer Guides (f).
Attach the Side Drawers and Center Drawer to the Drawer Guides (f) by using 12pcs Screws (g).
Use Phillips Head Screw Driver (not included) to tighten the Screws (g) clockwise until secure.
mx4
Hardware & Tools required
A
B
g
g
g
g
g
g
g
g
g
F
g
C
g
g
gx12
Phillips Head Screwdriver
( not included)
Hardware & Tools required
Page 8 of 8
Page 9
DESK
STEP 12:
Carefully turn over the desk.
Rotate the adjustable feet on bottom of each leg to desired height and leveling according to your floor surface.
Assembly is completed. The desk is ready to enjoy now!
Page 9 of 8
Loading...