TS890 Simple Manual
TS890 SERIES Transaction Terminal
(Support Paypass, Paywave, J/speedy, express pay, D-PAS)
Thank you for purchasing the TS890 series products.
The contactless & Signature Pad TS890 is to support the mag-stripe card , EMV /
ISO 7816 card and contactless payment systems. The small footprint size of the
device makes it easily to integrate to the current transaction system such as
Point-of-Sale terminal as the part of the system. The device communicates with
bank host by Modem , Ethernet or 3G. Allow to connect peripherals by RS232 or
USB.
FEATURES
_ Build-in thermal printer
_ Support mag-stripe , ICC , contactless transaction
_ Support 3G communication
_ Support Modem and Ethernet
TS890 Specifications
Processor
Memory System
LCD Display
SAM 3 SAM Card Slots (support 5V and 3.3V SAM) (option)
Contactless Build-in contactless module (option), supported ISO
RTC
Communication
Dimensions
Power Requirements
Operation Environment
32 bits high performance processor
Flash 8/16Mb, SDRAM 16Mb
128 x 64 pixels Graphical Display with LED Backlight
14443 13.56Mhz contactless card
Battery backup real time clock
Provided RS232/USB Ports for peripherals connection
Provideed standard USB Port to connect PC/Terminal
Modem/Ethernet/3G
(L)199 x (W) 94 x (H) 75mm
9VDC 5A
Temperature 0 °C to +50 °C; Humidity 5% to 90%
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This device is designed and
manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by
the FCC with the EUT transmitting at the specified power level in different channels.
TS890 Simple Manual
AGENCY APPROVAL
Specifications for FCC Class B
Changes or modifications are not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/ TV technician for help.
You are cautioned that any change or modifications to the equipment not expressly approve by the
party responsible for compliance could void your authority to operate such equipment.
TS890 Simple Manual
Installation
USB port
Ethernet port
Modem port
RS232 port
Interface RJ11 Pin Assignment ( RS232 )
The 9.0V power comes from external 9V@5A adaptor , the 5.0V power comes
from internal regulator .
Pin Assignment
Pin 232A 232B
1 GND GND
2 CTS GND
3 Rx Rx
4 RTS 5.0V
5 Tx Tx
6 9.0V 9.0V
TS890 3G model EMI test methods
Standard model
1. STD mode:
a. Transaction mode: Fill the paper roll and power on the TS890.
after booting select 4) Cardtes, select 1=TRANSACTIONS, select 1.Creadit card,
Insert the test smart card. (The card’s chip face up)
b. Idle mode: test without smartcard.
c. USB port test : Insert one USB disk to DEV USB port, start to test after select
USB(5
d. Ethernet connection: Set the IP of the PC to 192.168.0.XXX,connect the LAN cable
to PC, enter the command : ping 192.168.0.99 –t.
2. RFID mode:
a. Select 2)RFID, put the RFID test card on the LCD display. Test the carry only no
need the RFID test card.
3. 3G mode:
a. Power off the TS890, open the SAM door cover, insert the test SIM,select
1.GPRS/3G/LTE, press 1)ATI to 7) Loop sequenced.
b. Direct measure the 3G/LTE module output : The TS890 will lock after opening
the case, Enter the password will unlock the TS890.
4. Modem mode (Part68 test) : Insert the telephone cable to LINE port
Select 3)MODEM
1) ATDT : dail
3) ATH0 : On hook
4) ATH1 : Off hook
7) String : enter string
5. Modem mode (Part15B test) :
One PC Connected with modem and telephone switch box.
Run the modem test program on the PC. (ModemTest.exe)
Press the “Cancel” key twice. Keyin “password” and then press “Enter” key.
Press “6” key to select the self-test function.
Press “F3” key on the right side of the ALPHA key.
Press “2” key to select the 2) Dialup
Key in the number of test, and press “Enter”
Key in the dial number, and press “Enter”
Start the testing
Battery model
1. STD mode:
a. Transaction mode: Fill the paper roll and power on on the TS890.
after booting select 4) Cardtes, select 1=TRANSACTIONS, select 1.Creadit card,
Insert the test smart card. (The card’s chip face up)
b. Idle mode: test without smartcard.
c. USB port test : Insert one USB disk to DEV USB port, start to test after select
USB(5
2. RFID mode:
a. Select 2)RFID, put the RFID test card on the LCD display. Test the carry only no
need the RFID test card.
3. 3G mode:
a. Power off the TS890, open the SAM door cover, insert the test SIM, select
1.GPRS/3G/LTE, press 1)ATI to 7) Loop sequenced.
b. Direct measure the 3G/LTE module output : The TS890 will lock after opening
the case, Enter the password will unlock the TS890.
Loading...