Table of Contents
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Included with the
XC3510
Important Electrical Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Telephone Line Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Radio Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
More Than One Cordless Telephone. . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Selecting a Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Telephone Line Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Telephone Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Applying Power to the Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adapter Safety Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Desk or Tabletop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Direct Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting up your Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Extending the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installing the Handset Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning the Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Setting the Tone/Pulse Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Adjusting Ringer Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Automatic Digital Code Security. . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using your
XC3510
SERIES
Making and Receiving Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Changing Channels, Flash, and Page/Find . . . . . . . . . . . . . . . . . . 32
Programming your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Storing a Number in Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Storing a Tone/Pulse Number With a Pulse Dial System. . . . . . . . 35
Storing One-Touch Dialing Numbers . . . . . . . . . . . . . . . . . . . . . . . 37
Dialing a Stored Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Chain Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Erasing a Stored Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
SERIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
1
Important Safety Instructions
When using your telephone equipment, these basic safety precautions
should always be followed to reduce the risk of fire, electrical shock, and
injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Use a dry cloth
for cleaning without liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet Basement, or near a
swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The
telephone may fall, causing serious damage to the unit.
6. Slots and openings in the cabinet and the back or bottom are provided
for ventilation. To protect the product from overheating, these openings
must not be blocked or covered. This product should never be placed
near or over a radiator or heat register. This product should not be
placed in a built-in installation unless proper ventilation is provided.
7. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be damaged by persons walking on it.
9. Do not overload wall outlets and extension cords, as this can result in
the risk of fire or electrical shock.
10. Never push objects of any kind into this product through cabinet slots,
as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any
kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product.
Take it to qualified service personnel when service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
2
12. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the
operating instructions. (Adjust only those controls that are covered
by the operating instructions. Improper adjustment of other controls
may result in damage and will often require extensive repair work
by a qualified technician.)
E. If the product has been dropped, or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
Caution: To reduce the risk of fire or injury to persons by the battery, read
and follow these instructions:
1. Use only the appropriate type and size Battery Pack specified in this
Operating Guide.
2. Do not dispose of the Battery Pack in a fire. The cell may explode.
Check the Nickel-Cadmium Battery Disposal package insert for
disposal instructions.
3. Do not open or mutilate the Battery Pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic if
swallowed.
4. Exercise care in handling the battery in order not to short the battery
with conducting materials such as rings, bracelets, and keys. The
battery or conductor may overheat and cause burns.
5. Charge the Battery Pack provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the Battery Pack and
battery charger.
SAVE THESE INSTRUCTIONS
3
Introduction
Congratulations on your purchase of the Uniden
Telephone. The
XC3510
SERIES
is designed to exacting standards which
XC3510
SERIES
Cordless
provide reliability, long life, and outstanding performance.
Note: This series of Uniden phones is available in designer colors, and
these colors are designated by different model numbers.
Accordingly, this manual describes the operation of the
XC3510G, XC3514
, and the
XC3515
.
XC3510
Features
•
25 46/49 MHz Channels
•
Random Code Digital Security
•
UltraC le ar Plu s
•
AutoTalk
•
10 Number Memory
•
Redial/Pause and Flash
•
Reversible Handset Retainer
•
•
AutoSecure
•
Tone/Pulse Dialing
•
AutoStandby
One-Touch Dialing
•
1-way Page/Find Button
•
Handset Ringer/Volume Controls
•
Battery Saving Feature
,
The
XC3510
AutoTalk
allows you to answer a call by just removing the Handset from
SERIES
features include
AutoTalk
and
AutoStandby
.
the Base so you don’t have to waste time pushing buttons or flipping
switches.
AutoStandby
allows you hang up by simply returning the
Handset to the Base.
UltraClear Plus
The
true compander circuitry virtually eliminates background
noise. This innovative technology together with 25 different switchable
channels provides you with the best poss ible reception during all of your
conversations.
To protect you against misbilled calls which might result from your phone
being activated by other equipment, the
Code
digital security which automatically selects one of over 65 thousand
XC3510
SERIES
has
Random
digital security codes for the Handset and Base Units. Also the
AutoSecure
feature electronically locks your phone when the Handset is in
the Base.
To get the most from your phone, please read this Operating guide
thoroughly. Also be sure to complete the Product Registration for m and mail
it in.
4
Included with the XC3510
SERIES
If any are missing or damaged, do not contact the place of purchase. Instead
contact Uniden Customer Service at: (800) 297-1023, 8:00 am to 5:00 pm,
Eastern Standard Time, Monday through Friday.
Q
Handset Base Unit AC Adapter
Long Telephone
Cord
®
Operating Guide
OMXC3545
Rechargable Battery Short Telephone
Cord
Other Printed
Material
5
Important Electrical Considerations
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and damage
any device connected to it. Your
XC3510
Warning: Please do not attempt to unplug any appliance during an electrical
storm.
Caution: Changes or modifications to this product not expressly approved
by Uniden, or operation of this product in any way other than as
detailed by this Operating Guide, could void your authority to
operate this product.
Range
The
XC3510
by transmitting and receiving according to the highest specifications set forth
by the FCC. We have rated this phone to operate at a maximum distance
with the qualification that the range depends upon the environment in which
the telephone is used. Many factors limit range, and it would be impossible
to include all the variables in our rating. The Maximum Range rating of this
phone is meant to be used as a means of comparison against other range
claims.
SERIES
is designed to achieve the maximum possible range
SERIES
phone is no exception.
Telephone Line Problem s
The FCC has granted the telephone company the right to disconnect service
in the event that your phone causes problems on the telephone line. Also,
the telephone company may make changes in facilities and services which
may effect the operation of your unit. However, your telephone company
must give adequate notice in writing prior to such actions to allow you time
for making necessary arrangements to continue uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem. If you
determine that it is the cause, you must leave it disconnected until the
trouble has been corrected.
6
Radio Interfere nce
Radio interference may occasionally cause buzzing and humming in your
cordless Handset, or clicking noises in the Base Unit. This interference is
caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check around your
home to see what appliances may be causing the problem. In addition, we
recommend that the Base not be plugged into a circuit that also powers a
major appliance because of the potential for interference. Be certain that the
antenna on the unit is fully extended when needed.
In the unlikely event that you consistently hear other voices or distracting
transmissions on your phone, you may be receiving radio signals from
another cordless telephone or other source of interference. If you cannot
eliminate this type of interference, you need to change to a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs; to
minimize or prevent such interference, the base of the cordless telephone
should not be placed near or on top of a TV or VCR; and, if interference is
experienced, moving the cordless telephone farther away from the TV or
VCR will often reduce or eliminate the interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your home, they
must operate on different channels. Press the channel key to select a
channel that provides the clearest communication.
7
Installation
Selecting a Location
Before choosing a location for your new phone, there are some important
guidelines you should consider:
• The location should be close to both a phone jack and continuous
power outlet. (A continuous power outlet is an AC outlet which does
not have a switch to interrupt its power.)
• Keep the Base Unit and Handset away from sources of electrical
noise such as motors or fluorescent lighting.
• Be sure there is sufficient space to fully extend the Base Unit
antenna.
• The Base Unit can be placed on a desk or tabletop or mounted on a
standard AT&T or GTE wall plate.
• If you decide to mount your phone on the wall, make sure to change
the handset retainer so that the tab which holds the Handset faces
up. (See page 19 for more information.)
• You should charge your new phone for 15-20 hours before
completing the installation or using the Handset.
Telephone Line Outlets
There are two types of phone outlets:
Modular Jack
Most phone equipment available now uses modular jacks. Phone
cords are fitted with a molded plastic connector which plugs into
this type of jack. If you do not have modular phone jacks, contact
your local telephone company for information about their
installation.
Hard-wired Jack
Some equipment is wired directly to a phone jack, and these types
of installations require a modular jack converter. This type of
installation is not difficult; however, you should contact your Uniden
telephone dealer or a telephone supply store for advise about the
proper adapter or converter for your particular situation.
8
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords:
CAUTION:
• Never install telephone wiring during a lightning storm.
• Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
• Use caution when installing or modifying telephone lines.
Applying Power to the Base Unit
All the
XC3510
SERIES
phones require a standard electrical outlet (120
volts AC without a switch to interrupt power), and the included AC adapter.
Connect the adapter as shown below.
Wrap the power cord around the
convenient notch on the bottom.
Important:Place the power cord so that it does not create a trip hazard, or
where it could become chafed and create a fire or other
electrical hazards.
9
Adapter Safety Feature
The AC adapter furnished with this phone may be equipped with a polarized
line plug — a plug having one blade wider than the other. This plug will fit
into the power outlet only one way. If you are unable to insert the plug fully
into the outlet, try reversing the plug.
Do not alter the shape of the
blades of the polarized plug.
Note: If you cannot plug the AC adapter into the outlet, contact someone
about replacing the outlet.
Desk or Tabletop Installation
1. Place the Base on a desk or
tabletop.
10
2. Plug the AC Adapter cord
into the 9V DC input jack on
the Base Unit.
3. Place the AC Adapter cord
inside the molded channel.
4. Plug one end of the long
telephone cord into the
TEL LINE
jack on the Base
Unit.
11
5. Plug the other end of the
cord into the telephone jack
on the wall.
6. Plug the AC Adapter into a
standard 120V AC wall outlet.
12
Placement of the Handset
The unique design of your phone allows you to place the Handset on the
Base Unit either facedown or in an upright position. The battery is charged in
either position.
Upright Position for
Handset
Facedown Position for
Handset
Wall Installation
Standard Wall Plate Mounti n g
These phones are designed to be mounted on a standard AT&T or GTE wall
plate.
1. Plug the AC Adapter into the
Base Unit.
13
2. Place the AC Adapter cord
inside the molded channel.
3. Plug one end of the short
telephone cord into the
TEL LINE
jack on the Base
Unit.
4. Place the telephone cord
inside the molded channel on
the bottom of the Base Unit.
Then plug the other end of
the telephone cord into the
modular jack on the wall.
14
5. Place the Base Unit on the
posts of the wall plate and
push down until it’s firmly
seated.
6. Plug the AC Adapter into a
standard 120V AC wall outlet.
15
Direct Wall Mounting
If you do not have a standard wall plate, you can mount your phone directly
on a wall. Before mounting your phone consider the following:
• Select a location away from electrical cables, pipes, or other items
behind the mounting location that could cause a hazard when
inserting screws into the wall.
• Make sure the screws are securely fastened.
• Make sure the wall material is capable of supporting the weight of
the Base Unit.
1. Insert two mounting screws
15
3
⁄
inches apart. Allow
16
1
⁄
about
of an inch between
5
the wall and screw heads for
mounting the phone.
2. Plug the AC Adapter into the
Base Unit.
1/5 IN.
3 15/16 IN.
16
3. Place the AC Adapter cord
inside the molded channel.
4. Plug one end of the long
telephone cord into the
TEL LINE
jack on the Base
Unit.
5. Place the cord inside the
molded channel on the
bottom of the Base Unit.
17
6. Place the Base Unit on the
screws and push down until
it’s firmly seated.
7. Plug the other end of the
telephone line cord into the
wall jack.
8. Plug the AC Adapter into a
standard 120V AC wall outlet.
18
Setting the Handset Retainer
The handset retainer holds the Handset in place if your
XC3510
SERIES
phone is mounted on a wall. The steps below describe how to remove and
replace the retainer so that the tab faces up.
1. Push up on the Handset
retainer on the Base Unit,
and slide the tab out.
2. Flip the retainer over so the
tab faces up.
19
3. Put the retainer back into its
slot on the Base Unit.
4. Push down on the Handset
retainer until it snaps into
place.
20
Setting up your Phone
Extending the Antenna
Before using your phone, be
sure to raise its antenna to
the vertical position.
Installing the Hands et Batte ry Pack
1. Press in on the Battery
Cover Release.
NOTE
RED
BLK
WARNING !
AlwaysInstall BatteryCable
with Black Wire closest to
the left
21
2. Slide the battery
compartment cover down.
3. Align the plastic connector of
the Nickel-Cadmium battery
pack with its socket and plug
it in.
RED
BLK
WARNING !
Always Install Battery Cable
with Black Wire closest to
the left
RED
BLK
WARNING !
Always Install Battery Cable
with Black Wire closest to
the left
4. Place the battery pack inside
the battery compartment,
and slide the battery cover
back on.
RED
BLK
WARNING !
Always Install Battery Cable
with Black Wire closest to
the left
Note: The built-in Memory Backup feature allows up to 10 minutes to
disconnect the old battery pack and install a new one without
losing any phone numbers that may be stored in the telephone’s
memory.
22
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all charging contacts on
the Handset and Base Unit about once a month. Use a pencil eraser or other
contact cleaner. Do not use any liquids or solvents.
Contacts
TALK
BATT LOW
ABC DEF
2 3
1
JKL MNOGHI
5
TUV WXYPRS
8 9
7
OPER
0
123
FLASH VOLUME
CHANNEL
6
TALK
4
TONE
MEM
INT'C R.TONE R.VOL RDL/P
Contacts (On Bottom)
Extend A Phone
••
H
QSERIES
IN USE
PAGE / FIND
CHARGE
23
Charging the Battery Pack
Initial Battery Charging
The rechargeable Nickel-Cadmium battery pack must be fully charged
before using your phone for the first time. We recommend that the battery
pack charge for approximately 15-20 hours, without interruption, before
plugging the phone line into your new phone.
1. Place the Handset on the
Base Unit. Depending on
your installation, you can
charge the Handset in the
upright position
—or—
You can charge the Handset
in its facedown position.
24
2. Make sure the
CHARGE
LED
lights. If the LED doesn’t
light, check to see that the
AC adapter is plugged in,
and that the Handset is
making good contact with the
Base Unit charging contacts.
IN USE
PAGE / FIND
CHARGE
Continuous Battery Charging
For the best battery performance, return the Handset to the Base Unit at the
end of the day. This keeps the battery fully charged, so your phone works
best.
25
Low Battery Indicator
CHANNEL
TALK
ABC DEF
2 3
JKL MNOGHI
5
6
TUV WXYPRS
8
9
OPER
If the
When the Battery Pack in the
Handset is very low and
needs to be charged, the
TALK/BATT LOW
TALK/BATT LOW
LED flashes.
LED begins to flash, the phone is programmed to
TALK
BATT LOW
1
4
7
eliminate its functions to save power. The table below describes what to do
to return your phone to normal operation.
During a Call In Standby Mode
Only the
The Handset beeps and the
TALK/BATT LOW
T
button operates. None of the buttons will operate.
LED flashes once
The Handset
flashes once every 3 seconds.
TALK/BATT LOW
LED
every 3 seconds.
Complete your call as quickly as
You will not be able to make a call.
possible.
Return the Handset to the Base
Unit for charging.
Return the Handset to the Base
Unit for charging.
Note: Allow 15 to 20 hours without any interruption for the Handset to fully
recharge.
26
Setting the Tone/Pulse Switch
Be sure the
TONE/PULSE
switch is in the
TONE
TONE-PULSE
position.
Note: Most phone systems are Tone dialing. Check with your local phone
company if you are not sure whether your system is Tone or Pulse
dialing.
Adjusting Ringer Controls
To adjust the ringer volume
of your Handset, press
L
when the phone is not in use.
OPER
0
TONE
MEM
FLASH
Handset Ringer Volume
1 2 3
VOLUME
R.TONE R.VOL RDL/P
Control
27
You can also select one of
two different ringer tones for
the Handset.
Press
O
to select a
different ringer tone when the
phone is not in use.
OPER
0
TONE
MEM
FLASH
Handset Ringer Tone
1 2 3
VOLUME
R.TONE R.VOL RDL/P
Select Button
To adjust the receiver
volume, press
V
while
you are on a call.
OPER
0
TONE
MEM
FLASH
Handset Receiver Volume
1 2 3
VOLUME
R.TONE R.VOL RDL/P
Control
28
Automatic Digital Code Securi ty
Many cordless telephones operate similarly and on the same frequency.
Without digital code security, another Handset could make calls using your
Base Unit and telephone line. To avoid unauthorized calls on your phone, a
Digital Code feature was added to all
Code is shared only between the Handset and Base Unit. The Code is set
automatically
when you first use the phone.
To reset the Digital Code, be sure the Handset is on the Base, then:
1. Remove the Handset from
the Base Unit, and then set it
down again.
XC3510
SERIES
phones. This Digital
2. The
CHARGE
LED will blink to
indicate that the Digital
Security Code is set to one
of more the 65,000 codes.
IN USE
PAGE / FIND
CHARGE
29
If the Base Unit loses power while the Handset is off the Base, the Digital
Code may be erased. When this happens, the Handset will not function. To
establish communication between the Handset and Base Unit:
1. Remove the Handset from
the Base Unit (if it is on the
Base Unit).
2. Restore power to the Base
Unit, and place the Handset
back on the Base Unit.
3. The
CHARGE
LED will blink to
indicate that the Digital
Security Code is set.
IN USE
PAGE / FIND
CHARGE
30
Using your XC3510
Making and Receiving Calls
SERIES
Phone
The following features of the
XC3510
SERIES
phones are different
depending on the Handset’s location when you make or receive a call.
ANSWER
CALL
MAKE
CALL
HANDSET ON
BASE
Pick up Handset
(AutoTalk)
1) Pick up Handset
2) Press
T
3) Listen for dial tone
Press
1) Press
2) Listen for dial tone
3) Dial the number
HANDSET OFF
BASE
T
T
4) Dial the number
HANG
UP
Press
—
T
OR —
Return Handset to Base
(AutoStandby)
1) Pick up Handset
REDIAL
2) Press
T
3) Listen for dial tone
4) Press
R
Note: Sometimes when you press
an error tone and the phone will not disconnect. If this happens,
place the Handset on the Base Unit or press
holding the Handset close to the Base Unit.
1) Press
T
2) Listen for dial tone
3) Press
T
to hang up the phone, you may get
R
T
again while
31
Changing Channels, Flash, and Page/Find
To change channels or access call waiting while the phone is in use, or to
use the 1-way page to locate the Handset, follow these steps:
PRESS THESE KEYS YOU WILL HEAR
CHANGING
CHANNELS
FLASH
PAGE/FIND
Press H
Note: Change channels to
help eliminate background
noise.
If the
sounds, press
call waiting
F
tone
to
accept the waiting call.
—
OR —
If you have finished a call
and want to make another
call, press
F
to hang up
and get a dial tone.
Press
PAGE/FIND
on the
Base Unit to locate the
Handset.
A click similar to when
F
is pressed. There
may be a brief pause as
your phone searches for a
clear channel.
A click, a short pause, then
the caller (if you were on a
call)
—
OR —
A click, and then a dial
tone so you can make a
different call.
The Handset will beep 5
times.
32
Programming your Phone
All programming functions must be completed when your phone is in the
standby mode. The programming keys will not func tion while you are on the
phone.
Storing a Number in Memory
Use these keys
to store a
number in
memory.
Note: An error
tone wil sound
and the
programming
procedure will be
cancelled if more
than 20 seconds
elapses between
each keystroke
entry or step.
1. Remove the Handset from
the Base Unit.
TALK
1
4
7
TONE
MEM
TALK
BATT LOW
ABC DEF
2 3
JKL MNOGHI
5
TUV WXYPRS
8
OPER
0
1 2 3
VOLUME
R.TONE R.VOL RDL/PFLASH
CHANNEL
6
9
2. Press
The
M
.
TALK/BATT LOW
blinks.
3. Enter the number you want
to store (up to 16 digits).
LED
33
TALK
BATT LOW
1
4
7
CHANNEL
TALK
ABC DEF
2 3
JKL MNOGHI
5
6
TUV WXYPRS
8
9
OPER
5551212
4. If a pause is needed during
dialing to access a long
distance service, press
R
.
9R 5551212
Note: The
R
button counts as one digit. Pressing
once increases the length of the pause between numbers.
5. Press
M
again.
6. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
Q
R
more than
34
Storing a Tone/Puls e Number With a Pul se Dial System
If your phone is set up for pulse dialing, you can store a mixed mode number
so that you can easily access long distance services.
Use these keys
to store a mixed
mode number in
memory.
Note: An error
tone will sound
and the
programming
procedure will be
cancelled if more
than 20 seconds
elapses between
each keystroke
entry or step.
1. Remove Handset from the
Base Unit.
TALK
4
7
TONE
MEM
1
R.TONE R.VOL RDL/PFLASH
CHANNEL
TALK
BATT LOW
ABC DEF
2 3
JKL MNOGHI
5
8
6
TUV WXYPRS
9
OPER
0
1 2 3
VOLUME
2. Press
The
M
.
TALK/BATT LOW
LED
blinks.
3. Enter the number to be
dialed in pulse mode.
TALK
BATT LOW
1
4
7
CHANNEL
TALK
ABC DEF
2 3
JKL MNOGHI
5
6
TUV WXYPRS
8
9
OPER
5551212
35
4. Press
TONE
on the Handset.
TONE
MEM
OPER
0
1 2 3
VOLUME
R.TONE R.VOL RDL/PFLASH
5. Enter the number to be
dialed in tone mode.
6. If a pause is needed during
dialing to access a long
distance service, press
R
.
Note: The
R
button counts as one digit. Pressing
once increases the length of the pause between numbers.
7. Press
M
again.
8. Enter the memory location
(0-9).
A tone indicates that the
number is stored.
3300
R 3300
R
more than
Q
36
Storing One-Touch Dialing Numbers
Use these keys
to store a
number in a One
Touch dialing
button.
Note: An error
tone will sound
and the
programming
procedure will be
cancelled if more
than 20 seconds
elapses between
each keystroke
entry or step.
1. Remove the Handset from
the Base Unit.
TALK
4
7
TONE
MEM
1
R.TONE R.VOL RDL/PFLASH
CHANNEL
TALK
BATT LOW
ABC DEF
2 3
JKL MNOGHI
5
8
6
TUV WXYPRS
9
OPER
0
1 2 3
VOLUME
2. Press
The
M
.
TALK/BATT LOW
LED
blinks.
3. Enter the number you want
to store (up to 16 digits).
4. If a pause is needed during
dialing to access a long
distance service, press
R
.
TALK
BATT LOW
1
4
7
CHANNEL
TALK
ABC DEF
2 3
JKL MNOGHI
5
6
TUV WXYPRS
8
9
OPER
5551212
9R 5551212
Note: The
R
button counts as one digit. Pressing
once increases the length of the pause between numbers.
37
R
more than
5. Press
M
again.
6. Now press the One Touch
dialing button (
1 , 2
, or 3 )
you want to program.
A tone indicates that the
number is stored.
Dialing a Stored Number
Q
To dial a number previously stored in memory, follow these steps:
MEMORY ONE TOUCH KEYS
Remove the Handset from the
Base Unit.
Press
Press
T
Press
M
Press the One Touch dialing
Remove the Handset from the
Base Unit.
T
button where the number is stored.
Press the memory location number
(0-9).
Chain Dialing
On certain occasions, after dialing a number, you may be requested by the
party or service you are calling to enter a special access code, such as when
performing a banking transaction. To do this, simply:
1. Store the access code into one of the memory numbers.
2. Dial the main number.
3. At the appropriate time, press
number or One Touch Dialing button where the access code is saved.
M
followed by the memory location
38
Erasing a Stored Number
To erase a number previously stored in a memory location (0-9) or in One
Touch memory, follow these steps:
MEMORY ONE TOUCH KEYS
Remove the Handset from the
Base Unit.
Press
M
twice
. Press
Press the memory location
number (0-9).
Remove the Handset from the
Base Unit.
M
twice
.
Press the One Touch dialing
button you want to clear.
Note: An error tone will sound and the erase procedure will be cancelled if
more than 20 seconds elapses between each keystroke entry or
step.
39
Troubleshooting
If your
XC3510
SERIES
cordless Telephone is not performing to your
expectations, please try these simple steps. If you are still unable to resolve
the problems, contact Uniden Customer Service at (800) 297-1023, 8:00
a.m. to 5:00 p.m. EST, Monday through Friday.
Problem Suggestion
Charge light won’t come on when Handset
is placed in Base Unit.
• Make sure AC Adapter is plugged into the
Base Unit and wall outlet.
• Make sure Handset is properly seated in
Base Unit.
• Make sure that the charging contacts on
the Handset and Base Unit are clean.
Audio sounds weak and/or scratchy .
• Make sure that the Base Unit antenna is
fully extended and vert ic al .
• Move the Handset and/or Base Unit to
different locations and try again.
Can’t make or receive calls .
• Press the
channel.
• Check both ends of the Base Unit
telephone line cord.
CHAN
button to select another
Handset doesn’t ring or receive a page.
• Make sure the AC Adapter is plugged into
the Base Unit and wall outlet.
• Disconnect the AC Adapter for a few
minutes, and then reconnect it.
• Nickel-Cadmium battery pack may be
weak. Charge the battery on the Base
Unit for 15 – 20 hours.
• Set the
Handset to
RING ON/BATT SAVE
RING ON
.
switch on the
• Extend the Base Unit antenna vertically.
• The Handset may be too far away from
the Base Unit.
• Place the Base Unit away from noise
sources.
• The Digital Security Code may be erased.
Set the Digital Code.
40
Specifications
General – The
XC3510
SERIES
complies with FCC Part 15 and 68
Frequency Control Crystal controlled transmission
Modulation FM
Operating Temperature
– 10° to 50° C
Base Unit
Receive Frequency 48.76 to 49.99 MHz (25 Channels)
Transmit Frequency 43.72 to 46.97 MHz (25 Channels)
Power Requirements
Size
120V AC 60 Hz ± 3V AC
3
7
“ (W) x 5
4
17
” (D) x 1
32
7
“ (H)
8
Weight Approx. 13.1 oz.
Handset
Receive Frequency 43.72 to 46.97 MHz (25 Channels)
Transmit Frequency 48.76 to 49.99 MHz (25 Channels)
Power Requirements Rechargeable Ni-Cd Battery Pack
Size
3
2
“ (W) x 2
16
11
” (D) x 12
16
3
“ (H) (w/ antenna)
32
Weight Approx. 10 oz. (including battery)
Battery BT-185
Capacity 270 mAH, 3.6V
Talk Mode 6 hours
Standby Mode 7 days
Battery Save
5 weeks
Mode
Specifications, Features, and availability of Optional Accessories are all
subject to change without prior notice.
41
®
XC3510 Series
Cordless Telephones
UDZZ01361ZZ
Q
Operating Gu id e
PRECAUTIONS
Before you read anything else,
please observe the following:
WARNING!
Uniden Americ a Corp oration DOES NOT represent this unit to be waterproof.
To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT
expose this unit to rain or moisture.
RECHARGEABLE NICKEL-CADMIUM
BATTERY WARNING
This equipment contains a Rechargeable Nickel-Cadmium
Battery.
Cadmium is a chemical known to the State of California to
cause cancer.
The Rechargeable Nickel-Cadmium Battery contained in this
equipment may explode if disposed of in a fire.
Do not short circuit the battery.
Do not charge the Rechargeable Nickel-Cadmium Battery
used in this equipment in any charger other than the one
designed to charge this battery as specified in this Guide .
Using another charger may damage the battery, or cause
the battery to explode.
RECHARGEABLE NICKEL-CADMIUM
BATTERIES MUST BE RECYCLED OR DISPOSED
OF PROPERLY
Residents Of Minnesota should contact 1-800-225-PRBA for
information concerning reclamation and disposal of
Rechargeable Nickel-Cadmium batteries.
Residents outside of Minnesota should contact their local
authorities for information concerning reclamation and
disposal of Rechargeable Nickel-Cadmium batteries.
1.
Handset Controls and Keys
Antenna
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Talk/Battery Low
Indicator
Talk Button
T
Numeric Keypad
Tone Button
*
Memory
Programming
Button
Flash Button
M
F
Ringer Tone Select
Button
O
Channel Select
Button
H
Ring On/Battery
Save Switch
One Touch Dialing
Buttons
Redial/Pause
Button
Volume
R
V
/
Ringer Volume
Select Button
L
2
3
4
5
6
7
1
TALK
1
4
7
TONE
MEM
TALK
BATT LOW
ABC DEF
2 3
JKL MNOGHI
5
TUV WXYPRS
8
OPER
0
1 2 3
VOLUME
R.TONE R.VOL RDL/PFLASH
CHANNEL
6
9
9
11
12
RING
ON
BATT
SAVE
10
8
13
Base Unit Controls and Keys
12 3
5
4
Extend A Phone
••
H
Q SERIES
6
IN USE
PAGE / FIND
CHARGE
1.
2.
3.
4.
Tone/Pulse Switch
Telephone Line Jack
DC Power Jack
Handset Retainer
7
5.
6.
7.
8.
8
Base Unit Antenna
In Use LED
Charge LED
Page/Find Button
One Year Limited Warranty
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original
retail owner, this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate
and be of no further effect 12 months after the date of original retail sale. The
warranty is invalid if the Product is (A) damaged or not maintained as
reasonable or necessary, (B) modified, altered, or used as part of any
conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of
any system not manufactured by Uniden, or (F) installed or programmed by
anyone other than as detailed by the Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not conform
to this warranty at any time while this warranty is in effect, warrantor will
repair the defect and return it to you without charge for parts, service, or any
other cost (except shipping and handling) incurred by warrantor or its
representatives in connection with the performance of this warranty. THE
LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR
PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion
or limitation of incidental or consequential damages so the above limitation
or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This warranty is
void outside the United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If,
after following the instructions in this Operating Guide you are certain that
the Product is defective, pack the Product carefully (preferably in its original
packaging). Include evidence of original purchase and a note describing the
defect that has caused you to return it. The Product should be shipped
freight prepaid, by traceable means, or delivered, to warrantor at:
Uniden America Corporation
Parts and Service Division
8707 North By Northeast Blvd.
P.O. Box 501368
Indianapolis, IN 46250
(800) 297-1023, 8 AM to 5 PM EST, Monday through Friday
Covered under one or more of the following U.S.patents:
4,511,761
4,595,795 4,797,916
4,523,058
©1995 Uniden America Corporation. All rights reserved.
®
Printed in Hong Kong
Loading...