Uniden WDECT 2300, WDECT 2315, WDECT 2315+1 Quick Start Manual

Download

Wide Band Digital Technology provides the clearest sound and the best privacy.

Guide

Quick Start

WDECT 2300

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page a

[ i ]

INSTALLATION & SAFETY

• This symbol indicates important operating and servicing instructions.

• The earcap of this telephone may attract and retain small metallic objects.

AVOID -

connecting

more than

phones as ringing

may be impaired

AVOID multi power boards.

CHARGE the new phone for 15 - 20 hrs.

AVOID Moisture

Don’t overload the power outlet.

AVOID moisture

AVOID Television sets and other electronic appliances

AVOID Microwave ovens

AVOID Computers

AVOID other cordless telephones

CHOOSE a central location

Note: Ringing will not be impaired by

adding extra cordless handsets.

Choosing the best location for your phone. When choosing a location for your phone there are a number of appliances the phone should not be near, and areas you should avoid.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page i

[ ii ]

QUICK START GUIDE

This page is a very condensed version of the Owner’s Manual. It is designed to allow you to get your phone installed and operating as quickly as possible however it does not attempt to explain any of the advanced features of the WDECT2300 series.

1) Connect the AC adapter to the DC IN 9V

jack and to a standard AC wall outlet.

AC adapter (supplied)

To DC IN 9V

To AC outlet

Route the cord.

Make sure the AC Adapter/s remains switched ON at all times. Use only the Uniden AC Adapter/s supplied with this unit.

Start

Here!

Installing the Base Unit

2) Connect the telephone line cord to the

TEL LINE jack and to a telephone socket on the wall.

Australia

New Zealand

Telephone line cord

To TEL LINE

To telephone socket

For wall mounting, see “Mounting the Base Unit on a Wall” on page 6.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page ii

[ iii ]

Installing the battery pack

1) Press down on the battery cover release and slide the cover down until it comes off.

2) Connect the battery plug to the socket at the rear of the battery compartment. The RED and BLACK battery wires must match the RED and BLACK dots on the phone case for the plug to fit properly. Press firmly until it clicks into place.

3) Securely close the battery compartment cover by sliding it up until it snaps into place.

Red Wire

Black

Wire

3) Set the base on a desk or tabletop.

• Charge the handset battery pack for at least 15-20 hours before using your new cordless telephone for the first time.

• Use only the Uniden rechargeable battery pack (BT-446) supplied with your cordless telephone.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page iii

[ iv ]

Charging the handset

1) Place the handset in the main base unit or charging cradle with the keypad facing forward.

2) Make sure the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the base charging contacts.

• After installing the batteries in the handset, charge your handset at least 15-20 hours.

During a power cut or if the AC adapter is switched off, this telephone will not operate.

Recharge your phone on a regular basis by returning the handset to the base after each phone call.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page iv

[ v ]

CONTENTS

INSTALLATION & SAFETY i

QUICK START GUIDE ii

CONTENTS v

GETTING STARTED 1

Controls and Functions 1 Uniden Company Philosophy 3 Welcome 3 Features 4 Checking the Package Contents 5 Terminology 5 Mounting the Base Unit on a Wall 6 Battery Maintenance 7 Headset Installation 9 Display and Icons 9 About the Menu Options 10 Setting up the Menu 13

BASICS 20

Making and Receiving Calls 20 Keypad Lock 21 Placing a Call on Hold 21 Redialing a Call 22 Adjusting the Handset Ringer,

Earpiece and Speaker Volume 23

Mute Microphone 24 Tone Dialing Switch-Over (Australia Only) 24 Traveling Out-of-Range 24 Clarity Booster 25 Privacy Mode 25 Find Handset 26 Flash and Call Waiting 26 Using One Touch Voice Mail Access 27

PHONEBOOK 28

Phonebook 28 Storing Phone Numbers, Names,

Distinctive Rings, and Speed Dial 28 Steps for Entering Names and Special Characters 30 Viewing the Phonebook 32 Making Calls Using the Phonebook 33 Speed Dialing 33 Editing or Erasing a Stored Name,

Phone Number, Distinctive Ring, and Speed Dial 34 Chain Dialing 35

CALLER ID 36

Caller ID 36 Viewing the Caller ID List 37 Deleting a Caller ID Message 38 Using the Caller ID Message List 39

EXPANDING YOUR PHONE 40

Expanding your Phone 40 Register the Handset 41 Using Two Way Communication between the Handsets

Anywhere without the Base (Directlink) 42 Room Monitor 42 3-Way Conferencing 43 Intercom/Call Transfer Feature 43 Replacing the Base 44

ADDITIONAL INFORMATION 45

Changing the Digital Security Code 45 Note on Power Sources 46

TROUBLESHOOTING 47

INDEX 49

WARRANTY 50

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page v

GETTING STARTED

[ 1 ]

CONTROLS AND FUNCTIONS

11 12

18 19

20 21

1. Handset Antenna

2. Headset Jack Cover

3. Beltclip Hole

4. Hands-Free Speaker

5. Handset Battery Compartment

6. New Message LED

7. Handset Earpiece

8. LCD Display

9. /del Key

10. /vol/ / Key a. ringer volume control b. scroll keys for display screen

11. Key

12. redial/pause Key

13. speaker Key

14. Key

15. Key

16. Key

17. Key

18. Key

19. phonebook Key

20. /transfer/int’com Key

21. Handset Microphone

22. Handset Charging Contacts

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 1

[ 2 ]

27 28

23. Base Antenna

24. Base Charging Contacts

25. charge LED

26. Key

27. TEL LINE Jack

28. DC IN 9V Jack

Base

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 2

Congratulations on your purchase of the Uniden Multi-Handset Cordless System telephone. This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to 2 handsets. With the purchase of an Extra Handset WDECT2305 sold separately you can establish a 3-way conference call (both handsets and an outside line). You can now place a fully featured cordless handset anywhere in your home or office where AC power is available to connect the handset chargers.

Note: The illustrations in this manual are intended as a guide and may differ from actual unit.

WELCOME

[ 3 ]

To bring outstanding wireless communication products to people’s lives throughout the world.

UNIDEN COMPANY PHILOSOPHY

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 3

[ 4 ]

Great features of this cordless phone include:

• Designed and Engineered in Japan

• Wide Band Digital Technology

• Multi (2) Handset Capable

• Digital Duplex Speakerphone on Handset

Advanced Alpha Display Caller ID Features:

• Alpha Memory Dialling

• POP ID - Caller Name Identification*

• 20 Individual Caller Tone Allocation*

• 50 Caller ID * Memories with Phonebook

• 3 Line Full Dot Matrix LCD Display with Clock

• Maxi-Sound - Extra Loud Handset Volume Control

• Intercom/Announce Call Transfer**

• Handset Conferencing (2 Handsets + Outside Call)**

• Two-Way Communication between Handsets Anywhere without the Base**

• And More!

FEATURES

* Caller ID and POP ID and Individual Caller Tone Allocation (Distinctive Ring) features work only if you subscribe to

the service provided by your local telephone company. There is usually a fee for this service.

Range may vary depending on environmental and/or topographical conditions.

** These features require an optional Extra Handset (WDECT2305) sold separately.

UP349BH (WDECT2300) ENG OM 5/23/05 9:49 AM Page 4

[ 5 ]

CHECKING THE PACKAGE CONTENTS

Make sure you have received the following items in the package. If any of these items are missing or damaged, contact your retailer.

• Base unit (1)

• Handset (1)

• AC adapter (1)

• Rechargeable battery pack (1)

• Linecord (1)

Also included:

• This Owner’s Manual

• Other Printed Material

Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology explanation. Standby Mode - The handset is not in use, is off the cradle, and or speaker has not been pressed.

A dial tone is not present. Talk Mode - The handset is not in the cradle and or speaker has been pressed enabling a dial tone. “Talk” appears on the display. DirectLink - Two way communication between the handsets anywhere without the base.

TERMINOLOGY

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 5

[ 6 ]

MOUNTING THE BASE UNIT ON A WALL

You can mount your base directly to the wall. Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall.

• Mount your phone within distance of a working phone jack.

• Make sure the wall material is capable of supporting the weight of the base and handset.

• Use screws with anchoring devices suitable for the wall material where the base unit will be placed.

1) Insert two mounting screws into the wall (with their appropriate anchoring device),

85mm apart. Allow about 3mm between the wall and screwheads for mounting the phone.

2) Plug the AC adapter into the DC IN 9V jack on the telephone and then into a

Standard AC wall outlet.

3) Plug the telephone line cord into the TEL LINE jack on the telephone and then into

the telephone socket on the wall.

4) Align the mounting slots on the base with the mounting posts on

the wall.

5) Then push in and down until the phone is firmly seated.

This phone also can be mounted on any standard telephone wall plate (for Australia).

3mm

85mm

35mm

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 6

[ 7 ]

BATTERY MAINTENANCE

Cleaning the battery charging contacts

To maintain a good charge, it is important to clean the charging contacts on the handset once a month. Use a dry cloth or pencil eraser to clean.

Battery use time (per charge)

Fully charged

• Up to 7 hours continuous use.

• Up to 10 days when the handset is in the standby mode (up to 15 hours when in DirectLink mode) Recharge your phone on a regular basis by returning the handset to the charger after each phone call.

Low battery alert

When the batteries are very low and need to be charged, the phone is programmed to eliminate functions in order to save power.

The batteries need to be charged when:

- The empty battery icon appears.

- “Low Battery” appears in the display. If the phone is in the standby mode, none of keys will operate. If you are on a

call, complete your conversation as quickly as possible, and return the handset to the cradle.

Low Battery

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 7

[ 8 ]

Battery replacement and handling

When the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery.

Caution

• Use only the specified Uniden battery pack (BT-446).

• Do not remove the batteries from the handset to charge them.

• Never throw the battery into a fire, disassemble them, or heat them.

• Do not remove or damage the battery casing.

To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden battery model and Uniden adapter model specifically designated for this product.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 8

[ 9 ]

Your phone may be used with an optional headset, the Uniden HS910. To use this feature, insert the headset plug into the headset jack. Your phone is ready for hands-free conversations. Headset is available through Uniden authorized retailers.

HEADSET INSTALLATION

DISPLAY AND ICONS

SUN 12:00A Handset #1 New: 5 :OFF

Day of the week and time / battery icon Handset ID and Banner Number of new Caller ID calls received / Ringer off icon (when the ringer is Off)

Example of the standby mode display

ICON STATUS DESCRIPTION

Standby/Talk

Battery icons indicate the handset battery status. This icon cycles depending on the battery status (full, medium, low, and empty).

Standby Ringer off icon indicates that ringer is turned off.

Talk

Mute icon appears when you mute the handset.

Talk Speaker icon appears when the handset speaker phone is used.

Talk Booster icon appears when the Clarity Booster feature is in use.

Talk Privacy icon appears when the Privacy Mode is turned on.

:OFF

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 9

[ 10 ]

There are 5 main menu options, (DirectLink Mode, Room Monitor, Handset Setup, Global Setup and System Reset) and submenu options.

Summary of the Main Menu and Submenu

Two Way Communication between the Handsets Anywhere without the Base (DirectLink)

DirectLink Mode allows a pair of handsets to work without the base unit, for direct handset-to-handset communication. Use them at sporting events or while shopping to stay in contact with family members or friends. You must set the two handsets to DirectLink Mode to utilize this feature.

Room Monitor

This feature only works if you have two handsets, allowing you to monitor sounds in another room (see page 14 for setup). One handset is placed in the desired room to monitor (acts as remote mic), and the other is placed near listener (remote speaker). This is useful for monitoring child activities.

ABOUT THE MENU OPTIONS

During Global Setup and System Reset, make sure your cordless phone is in standby mode (not in use), and all handsets are within range of the mai n base unit.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 10

[ 11 ]

Handset Setup

The following submenu options must be set separately for each handset.

Submenu name Description

Edit Voice Mail Program or delete the voice mail access number (see page 14). Ringer Tones Adjusting the ringer tone (tone your phone makes when ringing)

(Default is Flicker) (see page 15).

Set the distinctive ring (see page 15). “Distinctive Ring” allows you to preset memory locations with a designated ring tone. When an incoming call

is received and the Caller ID information matches the information in one of Distinct. Ring the memory locations, the distinctive ring that has been stored for that (Distinctive is on) particular Caller will sound. If you have set multiple memory locations with

distinctive rings, switching the setting to “Distinctive Off” will result in no

distinctive ringing. All incoming calls will have a normal ring tone. Switching to

“Distinctive On” will activate all programmed distinctive ring memory locations. AutoTalk Allows you to answer the phone without pressing or

speaker.

(Default is on) When the AutoTalk is set to on, simply remove the handset from the cradle and

the phone automatically answers the call (see page 15). Anykey Answer Allows you to answer the phone without pressing or

speaker.

(Default is on) When the Anykey Answer is on, you can answer a call by pressing any number

key, , or on the handset (see page 16). Banner (True Banner) Customize your handset(s) by giving it a banner name. The name will be

displayed on the LCD screen during standby mode, Intercom, Transfer, Room

Monitor and Copy Phonebook operation. The banner name will be displayed on

the receiving handset as well (see page 16). Key Touch Tone Allows you to set your phone’s key touch-tone to on or off (tone your keypad

(Default is on) makes when keys are pressed) (see page 16).

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 11

[ 12 ]

Global Setup

If you change one of the Global settings, you change the setting for all additional handsets. Only one handset can change Global settings at a time.

Submenu name Description

Day & time Set the day and time of your display (see page 17). Name Tag (POP ID) Display the stored name with the Caller ID telephone number, if the displayed

(Default is on) Caller ID telephone number is exactly the same as a number stored in the

phone book (see page 17).

Insert 0 Add “0” or “00” to the number, when you receive the Caller ID message

(New Zealand only) (see page 17).

Dial Mode Set the dial mode to tone or pulse (see page 18). Most phone systems use tone (Australia only) dialing, which send DTMF tone through phone line. The default is tone dialing. (Default is tone) Depends on your dialing system, set the dial mode.

Copy Phonebook Allow you to transfer the phonebook data stored in one handset to another

handset (see page 18).

System Reset

System Reset is used to clear the handset’s ID from the main base unit, or the base ID from the handset.

Submenu name Description

Deregister HS Clear the handset ID from the base. Use this option, for example, when you change

the digital security code (see page 19).

Replacing Base Clear the base ID. Use this option, for example, if you wish to deregister the base

to use the handset with another base of the WDECT2300 series (see page 19).

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 12

[ 13 ]

Entering the Menu

1) Press the /del key in standby mode.

2) Use /vol/ or /vol/ to move the pointer to

a desired main menu (DirectLink Mode, Room Monitor, Handset Setup, Global Setup, and System Reset).

3) Press to select the desired main menu.

4) Use /vol/ or /vol/ to select a desired submenu, and then press to enter.

In the submenu, use /vol/ or /vol/ to select an item. Press to confirm your selection. For detailed instructions, see the following sections for the desired submenu.

5) To exit the menu, press or place the handset to the cradle.

DirectLink Mode

Entering the Two Way Communication between the Handsets Anywhere without the Base

1) Enter the DirectLink Mode menu (see “Entering the

Menu” on page 13). To enter DirectLink mode press [SELECT] appears.

2) Press to enter the DirectLink mode. You will

hear a confirmation tone, and DirectLink Mode Complete appears.

To adjust ringer volume, press /vol/ or /vol/ to select one of three ringer volume (off, low, or high).

3) To return back to the normal mode, exit the DirectLink mode. To exit the DirectLink

mode, press /del, and then , or return the handset to the cradle.

DirectLink Mode Cancel appears.

To enter DirectLink mode press [SELECT]

SETTING UP THE MENU

To back to the previous screen, press /del.

DirectLink Mode Room Monitor Handset Setup

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 13

[ 14 ]

Room Monitor

Using Room Monitor

1) Enter the Room Monitor menu (see “Entering the Menu” on page 13). To Room Monitor appears.

2) Select the handset you want to monitor by using

/vol/ or /vol/ .

3) Press . RoomMonitor appears, and you hear sounds in the room where the handset is installed.

4) To finish the Room Monitor, press or return the handset to the cradle.

Handset Setup

Programming your Voice Mail Access Number

1) Enter the Handset Setup menu, and then the Edit Voice Mail submenu (see “Entering the Menu” on page

13). Edit V_mail No. appears.

2) Enter your personal access number using the number keypad (0-9),

, , /del, or redial/pause (up to 20 digits).

3) Press . You will hear a confirmation tone.

To delete the current Voice Mail Access Number, delete all numbers in step 2 using /del and .

This is an example, if you have handset #1 and #2.

Edit V_mail No. 1234567890

To Room Monitor Handset #2

RoomMonitor Handset #2

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 14

Selecting a Ringer Tone

1) Enter the Handset Setup menu, and then the Ringer Tones submenu (see “Entering the Menu” on page 13).

There are 10 ringer tones or 10 Polyphonic Tones to choose from.

- Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder]

- Polyphonic Tones [Beethoven’s Symphony #9 (Beethoven9), For Elise (Elise), We Wish You A Merry Christmas (Merry-Xmas), Home Sweet Home (Hm Swt Hm), Lorri Song #6 (Lorri Song), When the Irish Eyes Are Smiling (Irish Eyes), Aura Lee, Let Me Call You Sweet Heart (Sweetheart), Waltzing Matilda (W Matilda), Old MacDonald (Old MacDld)]

2) Press /vol/ or /vol/ to move the pointer. You will hear the ringer or Polyphonic Tone as you scroll through the options.

3) Press . You will hear a confirmation tone.

Distinctive Ringer Setup

1) Enter the Handset Setup menu, and then the Distinct. Ring submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to select On or Off.

3) Press . You will hear a confirmation tone.

Setting the AutoTalk

1) Enter the Handset Setup menu, and then the Auto Talk submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to select On or Off.

3) Press . You will hear a confirmation tone.

[ 15 ]

Auto Talk On Off

Ringer Tones Flicker Clatter

Distinctive Ring On Off

Distinctive ringing will only operate if you subscribe to the Caller ID service.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 15

Setting the Anykey Answer

1) Enter the Handset Setup menu, and then the Anykey Answer submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to select On or Off.

3) Press . You will hear a confirmation tone.

Setting the True Banner

1) Enter the Handset Setup menu, and then the Banner submenu (see “Entering the Menu” on page 13).

2) Use the number keypad (0-9), , , or

/del to enter or edit the name.

3) Press . You will hear a confirmation tone.

Setting the Key Touch Tone

1) Enter the Handset Setup menu, and then the Key Touch Tone submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to select On or Off.

3) Press . You will hear a confirmation tone.

[ 16 ]

Banner _________ #1

Anykey Answer On Off

Key Touch Tone On Off

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 16

Global Setup

Setting Name Tag (POP ID)

1) Enter the Global Setup menu, and then the Name Tag submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to change the selection, On or Off.

3) Press . You will hear a confirmation tone.

Setting Insert Zero (New Zealand only)

1) Enter the Global Setup menu, and then the Insert 0 submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to change the selection, On or Off.

3) Press . You will hear a confirmation tone.

Setting Day and Time

1) Enter the Global Setup menu, and then the Day & Time submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to select the day of the week, and then press .

3) Press /vol/ or /vol/ to set hour and then press .

4) Press /vol/ or /vol/ to set minute and then press .

5) Press /vol/ or /vol/ to choose AM or PM, and then press . You will hear a confirmation tone.

[ 17 ]

Day & Time SUN 12:00 AM [ / / / /SELECT]

• When a Global setting is changed from one handset, this affects all registered handsets.

• For setting the Day and Time, the idle time-out is extended to 2 minutes.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 17

[ 18 ]

Setting the Dial Mode (Australia only)

1) Enter the Global Setup menu, and then the Dial Mode submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to change the select, Tone or Pulse (the initial setting is Tone).

3) Press . You will hear a confirmation tone.

Copy Phonebook

1) Enter the Global Setup menu, and then the Copy Phonebook submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to choose One Memory or All Memory, and then press . If you choose All Memory, go to step 4.

3) Press /vol/ or /vol/ , or the number keypad (0-9) to select the phonebook location you want to export, and then press .

4) Press /vol/ or /vol/ to select the handset to which you want transfer the phonebook locations, and then press .

If you choose All Memory in the step 2, Are you sure? appears. Press /vol/ or /vol/ to select Yes, and then press .

The phonebook locations will be transferred to the handset. On the receiving handset, Receiving and the handset name appear. When the transfer complete, Done! appears on the handset.

• If you receive a call or set up the Global Setup menu, the transfer will be canceled.

• If an error occurs, the phonebook locations transferred before the error were stored in the receiving handset.

Unavailable

appears on the display.

• When the memory of the receiving handset is full,

Not enough memory in Receiving Handset

appears. You cannot transfer the phonebook location.

Copy Phonebook One Memory All Memory :xxx

Dial Mode Tone Pulse

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 18

[ 19 ]

System Reset

De-register the Handset

1) Enter the System Reset menu, and then the Deregister HS submenu (see “Entering the Menu” on page 13).

2) Press /vol/ or /vol/ to select the handset ID to be de-registered from the list, and then press

. Deregister HS? appears.

3) Press /vol/ or /vol/ to select Yes.

4) Press . You will hear a confirmation tone. When de-registration is complete, Deregistration Complete appears.

5) After de-registering the handset, move to “Replacing the Base Setting” below.

Replacing the Base Setting

1) Enter the System Reset menu, and then the Replacing Base submenu (see “Entering the Menu” on page 13). Replace base? appears.

2) Press /vol/ or /vol/ to select Yes.

3) Press . You will hear a confirmation tone. The base information will be deleted. When replacing the base is complete, Place handset on main base to register appears, register the handset to the new base (see page 44).

Make sure to perform the Replacing Base after de-register the handset.

Deregister HS? Yes No

Which Handset? Handset #1 Handset #2

Replace base? Yes No

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 19

BASICS

This handset has a built-in speakerphone that allows you to have a hands-free conversation. This feature allows you to communicate easily while performing other tasks, such as cooking. appears during hands-free conversations.

You can easily switch a call from normal conversation to hands-free conversation. To switch a call, press speaker during the call.

From the Handset

Normal conversation Hands-free conversation

To answer a call Handset On the Cradle

Pick up the handset (AutoTalk)

or pick up

the handset and press .

Handset Off the Cradle Handset Off the Cradle

Press any number key, , Press

speaker.

or (Any Key Answer), or press .

To make a call Handset Off the Cradle Handset Off the Cradle

1) Press . 1) Press speaker.

2) Listen for the dial tone. 2) Listen for the dial tone.

3) Dial the number. 3) Dial the number.

OR OR

Dial the number, and then Dial the number, and then press . press speaker.

To hang up Press , or return the handset to the cradle (AutoStandby). To enter a pause When you dial the number, press

redial/pause.

within the “P” appears in the display, which represents a pause. dialing sequence

[ 20 ]

MAKING AND RECEIVING CALLS

• To set Autotalk, see page 15 or to set Anykey Answer see page 16.

• The handset microphone is located at the bottom of the handset (see “Controls and Functions” on page 1). Position yourself as near to the handset as possible and speak clearly.

• If the line is in use by another handset(s),

Line In Use

appears in the display of all registered handset’s display, that are not in use.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 20

The Keypad Lock prevent user from pressing the keypad accidentally. You can still answer calls, and receive page and phonebook locations, and the keypad lock is reactivated after the operation.

To lock the keypad

Press and hold until you hear a confirmation tone. Keypad Locked appears.

If anykey is pressed when keypad is locked, To unlock keypad press & hold * key appears.

To unlock the keypad

Press and hold again. Keypad Unlocked appears.

[ 21 ]

PLACING A CALL ON HOLD

KEYPAD LOCK

1) During a call, press /transfer/int’com. The call will be put on hold.

After 10 seconds of pressing /transfer/int’com or by pressing the key, the handset display screen will read, Line On Hold.

2) To talk to the caller, press or speaker on a handset. The phone will return back to the call.

You can hold a call for 5 minutes, when 5 minutes has passed, the call is disconnected and the phone returns to standby mode.

Hold,to transfer Handset #2

SUN 12:00A Handset #1 Line On Hold

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 21

The last three phone numbers dialed can be quickly redialed.

Redialing from Standby Mode

1) Press redial/pause in standby mode.

2) Press redial/pause again. Each press of redial/pause will display one of the last three

number redialed.

3) Press or speaker. The selected

number is dialed.

4) To hang up, press .

Redialing from Talk Mode

1) Press or speaker.

2) Press redial/pause. The last number dialed will

be displayed and redialed. To hang up, press .

Deleting a Redial Record

1) Press redial/pause in standby mode.

2) Press redial/pause repeatedly to display the

number to be deleted.

3) Press /del.

3) Press /vol/ or /vol/ to choose Yes.

4) Press . The redialed number is deleted.

Storing a Redial Record

1) Press redial/pause in standby mode.

2) Press redial/pause repeatedly to display the number to be stored.

3) Press . Store/Edit Name appears.

4) To complete the setting, follow the steps 3-8 in “Storing Phone Numbers, Names,

Distinctive Rings, and Speed dial” on page 28-29.

[ 22 ]

REDIALING A CALL

• If the number exceeds 32 digits, only the first 32 digits are retained in redial memory.

• If the redial memory is empty, you will hear a beep.

Delete Redial1? Yes No

<Redial1> 8007303456

<Redial2> 2145452930

redial/pause

<Redial3> 8175551212

redial/pause

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 22

[ 23 ]

ADJUSTING THE HANDSET RINGER, EARPIECE AND SPEAKER VOLUME

Handset ringer volume

Press the volume up key or volume down key (labeled as

/vol/ or /vol/ in standby mode to select one

of three ringer volume (off, low, or high).

Earpiece and speaker volume

Pressing the volume up key or volume down key (labeled as

/vol/ or /vol/ key) during a call will change the earpiece and speaker volume of the handset. This setting will remain in effect after the telephone call has ended.

Ringer Mute

You can temporarily mute the incoming ring. When the handset is off the cradle and the phone is ringing, press . The incoming ring will return to the previous setting starting with the next incoming call.

When you press volume up key ( /vol/ ) in the maximum volume level or volume down key ( /vol/ ) in the lowest volume level, an error tone sounds.

Standby Mode - The handset is not in use and has not been pressed.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 23

[ 24 ]

TRAVELING OUT-OF-RANGE

During a call, as you begin to move your handset too far from your base unit, noise may increase. If you pass the range limits of the base unit, you will hear a beep and see Out of Range on the display, and then the handset returns to standby mode. You may return to the call if you move your handset within the range limits of the base and press or speaker within 30 seconds.

MUTE MICROPHONE

You can temporarily turn off the microphone so that the person you are talking with cannot hear you.

1) Press /del during talk mode (while phone is in use).

2) Press /vol/ or /vol/ to move the pointer to Mute and then . Mute On and appear in the display. To cancel muting, repeat above step again when Mute is set to on, Mute Off appears.

TONE DIALING SWITCH-OVER (AUSTRALIA ONLY)

Some telephone companies use equipment that requires pulse dialing (sometimes referred to as rotary dialing). If you need to enter tone dialing digits, you can switch-over to tone dialing during the call. This feature is useful when you need tone dialing to use automated systems, for example, entering your bank account number after you have called your bank.

Initially make your call with the pulse dialing mode. Once your call connects, press . Enter the desired number. These digits will be sent as tone dialing. Once the call ends, the tone mode is canceled and pulse dialing mode resumes.

• The tone feature only applies when the dial mode is set to pulse.

• This special number can be stored in a memory location. This is referred to as Chain Dialing (see page 35)

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 24

If you encounter interference while using your phone, you can manually improve the sound by setting the Clarity Booster to on. This works only when the phone is in use.

1) Press /del during talk time (while phone is in use).

2) Press /vol/ or /vol/ to move the pointer to Clarity Boost, and then . Boost On and B appear in the display. To turn Off the Clarity Booster, repeat above step again when the Clarity Booster is on, Boost Off appears.

[ 25 ]

• Normally, the talk time duration is 7 hours, however, when the Clarity Booster is On, the talk time duration will be up to 5 hours with fully charged batteries.

• Clarity booster automatically turns off after each call.

CLARITY BOOSTER

Privacy Mode allows you privacy, and guarantee of no interruption from another registered handset. This works only when the phone is in use.

1) Press /del during talk time (while phone is in use).

2) Press /vol/ or /vol/ to move the pointer to

Privacy Mode, and then . Privacy Mode On and appear in the display.

To exit the Privacy Mode, repeat above step again when the Privacy Mode is on. Privacy Mode Off appears.

PRIVACY MODE

Talk B Boost On

Talk Privacy Mode On

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 25

[ 26 ]

FIND HANDSET

To locate the handset, press on the base when the base is in standby mode. All registered handsets beeps for 60 seconds, and “Paging” appears on the handset display. To cancel paging, press any key on the handset or on the base.

FLASH AND CALL WAITING

If you have Call Waiting service and a call waiting tone sounds during a call:

AUSTRALIA: Press , then 2 to switch between callers.

NEW ZEALAND: Press to switch between callers.

If the battery pack is completely drained, the handset will not beep when paging.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 26

[ 27 ]

USING ONE TOUCH VOICE MAIL ACCESS

If you subscribe to voice mail service, you can use your phone to access your voice mailbox. The new message LED flashes whenever you have messages waiting in your voice mailbox. Just program the handset with your access number, and you can get your messages at the touch of a button on the handset. (The voice mail service provider will supply you with the access number. This number may be simply a phone number. Refer to the provider’s literature).

Dialing your Voice Mail Service

Once you’ve programmed your personal access number, you can dial your mailbox with the touch of a button. When you have messages, simply pick up the handset and press . If you have not entered the access number or it has been deleted, when you press the , No Number Stored To store number press [MENU] appears and you will hear a beep. The phone returns to standby mode.

Voice Mail Access

The new message LED on the handset is designed to work with your voice mail service provided by your local telephone company. The LED flashes when you have new incoming messages in the voice mail service. You may need to occasionally reset the indicators if they remain on after you’ve retrieved your messages. To reset the indicators, when the phone is in standby mode press and hold on the base until the paging sound stops (about 5 seconds).

• To program or delete your Voice Mail Access Number, See page 14.

• You must subscribe to voice mail service from your telephone company in order to use this feature. The voice mail service company will provide you with the access number.

• Voice Mail Access Numbers : Australia Message Bank : 125101 Home Messages : 101 New Zealand Call Minder : 083210

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 27

PHONEBOOK

[ 28 ]

The Phonebook allows you to dial a number using just a few key presses. Your phone stores names/numbers in the phonebook memory location, and you can search names in alphabetical order. You have a total of 100 locations that can be used for the phonebook (including the speed dials) and Caller ID messages (up to 50 locations).

1) When the phone is in standby mode, press phonebook. The handset displays the following items: (1st line) The number of the phonebook locations used (2nd line) How to search (press the number keypad,

/vol/ or /vol/ ) (3rd line) How to enter the storing operation (press the key)

2) Press , Store/Edit Name appears.

3) Enter the name (up to 16 characters) by using the number keypad (see the “Steps for Entering Names and Special Characters” on page 30). If a name is not required, go to step 4. <No Name> will be used as the name.

4) Press to store the name, Store/Edit No. appears.

5) Press the number keypad to enter the phone number (up to 20 digits), press to store the number.

STORING PHONE NUMBERS, NAMES, DISTINCTIVE RINGS, AND SPEED DIAL

PHONEBOOK

• Your phone has 100 memory locations for Caller ID messages (up to 50 locations) or stored Phonebook numbers.

• Selecting a speed dial location where a number is already stored releases the old number’s speed dial setting. The new number will be stored in the speed dial location.

• When the memory is full, you will hear a beep and

Memory

Full

appears. You cannot store names and numbers.

• The pause key counts as one digit. Pressing

redial/pause

more than once increases the length of the pause between numbers. Each pause represents a 2 second delay.

Store/Edit Name Movies

Phonebook :100 Search [A-Z/ / ] Store [SELECT]

Store/Edit No. 8007303456

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 28

[ 29 ]

6) Distinctive Ring appears. Press /vol/ or /vol/ to move the pointer to one of the Distinctive

Ring options, and then press .

7) Speed Dial appears. Press /vol/ or /vol/ to move the pointer to select the Speed dial location (10 locations: SPD1-SPD0).

8) Press . You will hear a confirmation tone, and Done! appears in the display.

If you choose not to store a Distinctive Ring, simply select the “No Selectn” option.

If you choose not to store the name/number as a Speed Dial, simply select the “No Selectn” option.

Speed Dial No Selectn SPD1:<Empty>

Distinctive Ring No Selectn Flicker

Movies 0295979035 Beethoven9/SPD1

Distinctive ringing will only operate if you subscribe to the Caller ID service.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 29

[ 30 ]

STEPS FOR ENTERING NAMES AND SPECIAL CHARACTERS

Refer to the letters on the number keys to select the desired characters. With each press of a number key ( - ), the displayed character appears in the following order: upper case letters first, lower case letters next and finally the number corresponding to the key.

Number of times key is pressed

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 30

[ 31 ]

If the next character uses the same number key, you must press

to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.

If you make a mistake while entering a name

Use or to move the cursor to the incorrect character. Press /del to erase the wrong character and then enter the correct character. To delete all characters, press and hold /del.

For example, to enter Movies:

1) When the phone is in standby mode, press phonebook.

2) Press , Store/Edit Name appears.

3) Press 6 once, and then press to move the cursor to the right.

4) Press 6 six times.

5) Press 8 six times.

6) Press 4 six times.

7) Press 3 five times.

8) Press 7 eight times.

9) When finished, press .

To continue to store the telephone number, proceed to step 5 on page 28.

Copy Phonebook: To copy the phonebook entries to another handset please refer to page 18.

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 31

[ 32 ]

During a call, don’t press or the call will be disconnected.

VIEWING THE PHONEBOOK

Your phone stores names/numbers in the phonebook memory locations, and you can search names in alphabetical order. You can view the phonebook even while the phone is in use.

1) Press phonebook.

If you recall the phonebook during a call, Store [SELECT] will not appear.

2) Press /vol/ , /vol/ , or the number keypad to scroll through the phonebook locations. Phonebook locations appear in alphabetical order (from first to last when you press /vol/ , from last to first when you press /vol/ ).

You can also use letters on the number keys to select the first letter of the desired name. Press a number key (2-9 and 0) once for the first letter, press twice for the second letter, and so on. The first location that begins with the letter you entered appears.

For example, to search for “Movies,” press 6 once. Press /vol/ or /vol/ , until the phonebook location is displayed.

3) To finish the viewing operation, press (or phonebook during a call).

Phonebook :100 Search [A-Z/ / ] Store [SELECT]

UP349BH (WDECT2300) ENG OM 1/5/05 1:18 PM Page 32

[ 33 ]

MAKING CALLS USING THE PHONEBOOK

From Standby Mode

1) When the phone is in standby mode, view the phonebook location to dial (see “Viewing the Phonebook” on page 32).

2) Press or speaker. The displayed number is dialed.

3) To hang up press .

From Talk Mode

1) Press or speaker.

2) View the phonebook location to dial (see “Viewing the Phonebook” on page 32).

3) Press . The number in the displayed phonebook location is dialed.

4) To hang up press .

SPEED DIALING

If you store a phone number in a speed dial memory location (10 locations:SPD1 - SPD0), you can use the speed dialing feature. When the phone is in standby mode, press and hold a number key ( - ) associated with the speed dial until the phone number appears, then press or speaker. The number stored in speed dial (SPD1 SPD0) is dialed.

Movies 0295979035 Beethoven9/SPD1

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 33

[ 34 ]

1) When the phone is in standby mode, press phonebook.

2) Press /vol/ or /vol/ , or the number keypad to view the phonebook locations (see “Viewing the Phonebook” on page 32).

a. Editing the Stored Data

1) When the phonebook location to be edited appears,

press . Store/Edit Name appears.

2) Follow the steps 3 to 7 under “Storing Phone

Numbers, Names, Distinctive Rings, and Speed Dial” on page 28 to complete the editing operation.

3) Press . You will hear a confirmation tone.

b. Deleting the Stored Data

1) When the phonebook location to be deleted

appears, press /del.

Delete Memory? appears.

2) Press /vol/ or /vol/ to move the

pointer to Yes.

3) Press . You hear a confirmation tone.

Deleted! appears in the display.

EDITING OR ERASING A STORED NAME, PHONE

NUMBER, DISTINCTIVE RING, AND SPEED DIAL

Phonebook :100 Search [A-Z/ / ] Store [SELECT]

Store/Edit Name Movies

Delete Memory? Yes No

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 34

[ 35 ]

CHAIN DIALING

The memory locations in the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing.

An example of this is a bank account number. Store the account or special number in one of the phonebook locations. (Refer to “Storing Phone Numbers, Names, Distinctive Rings and Speed Dial” on page 28.) When you call your bank and you are prompted to enter the account number, scroll through your phonebook locations until you find your account number, and then press .

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 35

[ 36 ]

You must subscribe to Caller ID services through your local telephone provider to use these features.

When the telephone rings, the Caller ID feature allows you to view the caller’s name, and phone number along with the date and time of call. Additionally, you can dial a number stored in the Caller ID list or save data to your Phonebook locations.

Important:

Memory locations for Caller ID messages and Phonebook locations (including Speed Dials) are common, you can store up to 100 in total (up to 50 Caller ID locations). A Caller ID message is not stored when you have stored 100 of the phonebook locations. The earliest Caller ID message is overwritten when you have stored 100 of the phonebook locations and Caller ID messages (up to 50 locations) in total.

1) When the Caller ID message is received, the display shows the caller’s phone number along with the date and time. The incoming call information is stored in the Caller ID record. If the Caller ID service includes the caller’s name, the name will appear in the display (up to 15 characters). You may receive any one of the following messages: When a private name is received Private When a unknown name is received Unavailable When a overseas call (0000) is received (New Zealand only) OVERSEAS CALL When invalid data is received Incomplete Data

CALLER ID

21/12 11:20AM Jane Smith 0295979035

The date and time received

Caller's name

Caller's phone number

CALLER ID

• If you answer a call before the Caller ID message is received (for example, before the second ring), the Caller ID message will not appear.

• When the call is received via a telephone company that does not offer Caller ID service, the caller’s phone number and name does not appear. (This includes some international calls.)

• When the call is via a private branch exchange (PBX), the caller’s phone number and name may not appear.

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 36

[ 37 ]

VIEWING THE CALLER ID LIST

The Caller ID list stores information for incoming calls - even unanswered calls. You can store 100 of the Caller ID messages (up to 50 locations) and Phonebook locations (including SpeedDials) in total. You can view the Caller ID list during a call or when the phone is in standby mode.

1) Press .

The summary screen appears. The screen shows the number of new messages and total messages.

2) To view the Caller ID messages in historical order (from new to old or from old to new), repeatedly press /vol/ to scroll through the messages from the latest to the earliest, or /vol/ to scroll back through the messages.

To view the Caller ID messages with alphabetical search, press the number key pad (2-9 and 0) with the letter associated with the first letter of the desired message.

3) To finish the viewing operation, press (or during a call).

Once you view the Caller ID list with alphabetical search, you cannot switch back to historical order (from new to old or from old to new) unless you exit and re-enter the operation.

Data errors appear as “”.

2) When you pick up the phone, the display changes to Talk. (AutoTalk feature is set to on).

• The number of calls from the same Caller ID appears next to the received time. Once you view the new message, the number will be cleared and disappear.

• During a call, don’t press end or the call will be disconnected.

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 37

[ 38 ]

Deleting Information from the Caller ID List

1) When the phone is in standby mode, view the Caller ID information to be deleted (see “Viewing the Caller ID List” on page 37).

2) Press /del. Delete Caller ID appears.

3) Press /vol/ or /vol/ to choose Yes.

4) Press . You will hear a confirmation tone.

Deleting all Caller ID names/numbers

1) When the phone is in standby mode, press call id.

2) Press /del. Delete All? appears.

3) Press /vol/ or /vol/ to choose Yes.

4) Press . You will hear a confirmation tone.

DELETING A CALLER ID MESSAGE

• Once the Caller ID data has been deleted, the information cannot be retrieved.

• Standby Mode -

The handset is not in use and

has

not been pressed.

• Talk Mode -

The handset is not in the cradle and

speaker has been pressed enabling a dial tone.

Talk appears on

the display.

Delete Caller ID Yes No

Caller ID New : 5 Total: 25

Delete All? Yes No

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 38

[ 39 ]

Calling a party from the Caller ID list

From Standby mode

1) When the phone is in standby mode, view the Caller ID message (see “Viewing the Caller ID List” on page 37).

2) Press or speaker. The displayed phone number dials automatically.

From Talk mode

1) Press or speaker.

2) View the Caller ID message you want to dial (see “Viewing the Caller ID List” on page 37).

3) Press . The displayed phone number will be dialed.

Adding Zero to Caller ID message (New Zealand only)

While you review Caller ID information while the Insert Zero option is set to On, “0” is inserted. Refer to page 17 “Insert Zero (New Zealand only)” to set the Insert Zero option to On or Off. New Zealand Telecom customers should leave Insert Zero to On. Other New Zealand companies may require Insert Zero set to Off.

Storing Caller ID messages in the Phonebook

Messages shown in the Caller ID list can be stored in the phonebook. The phone number and name of the party on the Caller ID list can be stored in memory.

1) When the phone is in standby mode, view the Caller ID message to be stored.

Then press . Store/Edit Name appears.

2) To complete the setting, follow the steps 4-8 in “Storing Phone Numbers, Names, Distinctive Rings, and Speed dial” on page 28.

USING THE CALLER ID MESSAGE LIST

• You cannot make a call from the Caller ID list if your phone is connected to a private branch exchange (PBX).

• If a call comes in via a telephone system that does not offer Caller ID service, no information is stored.

• If the Caller ID message was received as a private/unknown number, or the message does not have the number, you cannot store the message in the Phonebook. If it was received as private/unknown name, the message will be stored as <No Name>.

• Even if the 100 memory locations are full, the message will be stored in the Phonebook. However, the message will be erased from the Caller ID list.

21/12 11:20AM Jane Smith 0295979035

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 39

EXPANDING

YOUR PHONE

[ 40 ]

• To use the WDECT2305, register it to the original base.

• Save this manual for detailed operation.

• All of the handsets ring when a call is received.

2 Multi-Handset Expendability

You may expand your WDECT2300 with the purchase of an extra handset WDECT2305. Your phone supports up to 2 handsets (including the handset supplied with your phone). You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger. The 2 handsets can be used for an outside and/or intercom call. For example, the phone permits 3-way conferencing (2 handsets and an outside line).

EXPANDING YOUR PHONE

IMPORTANT:

• If you purchase a WDECT2305 extra handset, please register the handset to the WDECT2300 series base before use. The WDECT2305 will not operate until it is registered.

• If you change a setting of the Global Setup menu in one of the handsets, you change settings for all the handsets. For all other features they must be set separately through each handset.

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 40

[ 41 ]

If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time.

The handset ID for the supplied handset was assigned at the factory, which has #1 in the display. When you register additional handset to the base, the handset ID will be assigned.

1) Before registering the extra handset, the battery pack must be charged for 15-20 hours.

2) Place the extra handset in the main base unit to begin registration.

3) While the handset is registering, Handset Registering will appear in the LCD.

When Registration Complete is displayed, the handset has been registered to the base.

If Registration Failed appears, please try these steps again.

Registration Complete

Extra Handset

Charger

Main Base

Extra Handset

Main Base

Charge the handset for 15-20 hours.

Place the extra handset in the main base to register.

Place handset on main base to register

• An extra handset can be registered when the main base is in standby mode.

• Standby Mode -

The handset is not in use and

has

not been pressed.

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 41

[ 42 ]

To use this feature, you must enter the two handsets into the DirectLink mode first.

To enter the DirectLink mode

See page 13

This feature allows you to monitor sounds in another room. To use this feature, place the handset in the desired room to monitor (act an remote mic), and place the other near listener (remote speaker). For instruction, see “Using the Room Monitor” on page 14.

DirectLink Call

1) When the phone is in the DirectLink standby mode, press (example of DirectLink from handset #1).

2) Select the handset to which you wish to DirectLink with by pressing the number keys (1-4). Your handset will then page the other handset.

3) On the receiving handset, press , or if Any Key Answer is on, press any number key, , or .

4) When you finish your conversation, press on either handset. Return the handset to the cradle, or press /del, and then to return to normal standby mode (canceling DirectLink mode).

USING TWO WAY COMMUNICATION BETWEEN THE

HANDSETS ANYWHERE WITHOUT THE BASE (DIRECTLINK)

ROOM MONITOR

Two handsets can be in Direct Link mode while other handsets are in use.

SUN 12:00A Handset #1 DirectLink Mode

To DirectLink a handset press [1-4]

DirectLink << Handset #1

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 42

[ 43 ]

3-WAY CONFERENCING

INTERCOM/CALL TRANSFER FEATURE

The phone permits 3-way conversations between 2 handsets, and an outside line.

1) During a call, press on another handset to initiate the 3-way conversation.

2) To remove either caller from your conversation, press key on either handset. The other handset will still be connected to the call.

If you have one or more extra handsets, you can enjoy an intercom call between handsets. Also, you can place an outside call on hold and transfer the call to another handset.

Intercom

1) Press /transfer/int’com in standby mode.

2) Select the handset you want to talk with from the selection list within 30 seconds. To select the handset, press /vol/ or /vol/ and then press

If you select All, all handsets will be paged. An intercom tone sounds.

3) On the receiving handset, to answer the call, press or

/transfer/int’com. If you turn AutoTalk on, pick up the handset from the cradle. If Anykey Answer is on, press any number key, , or .

4) To finish the intercom call, press on either handset.

• If the party is busy or out of range, the handset returns to standby mode.

• If any of the following occurs while selecting the other handset, the operation will be canceled.

- Press or speaker.

- Receive an outside/intercom call or page.

• When the party does not answer within one minute, the operation is canceled.

• Standby Mode -

The handset is not in use and

has

not been pressed.

To intercom Handset #2

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 43

[ 44 ]

Call Transfer Feature

1) During a call, press /transfer/int’com.

2) Select a handset to transfer the call within 10 seconds. (Refer to step 2 in the intercom section on page 43).

The call will automatically be placed on hold, and an intercom tone sounds.

To cancel the transfer, press or speaker on the initiating handset.

3) On the receiving handset, to answer the page, press or /transfer/int’com. If you turn AutoTalk on, pick up the handset from the cradle. If Anykey Answer is On, press any number key, , or . The intercom mode is activated, but the caller is still on hold.

4) To transfer the call, press on the initiating handset, and press on the receiving handset.

REPLACING THE BASE

If the base unit is replaced with a different base from this same series of cordless models, you must clear handset (s) and base identification numbers. To do this, select “System Reset” from handsets display menu option list (see page 19 for guidance).

For model number verification, visit our website

www.uniden.com.au or www.uniden.co.nz

Hold,to transfer Handset #2

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 44

[ 45 ]

The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code. To change the digital security code:

1. Perform the “System Reset” menu options (“De-register the Handset” and “Replacing the Base Setting”) for all the handsets you have (see page 19).

2. To register all the handsets do the following steps:

1) Place a handset, one at a time in the base.

2) Registration starts automatically.

While registering Handset Registering appears in the display.

3) When the registration is complete, Registration Complete appears in the display.

4) Repeat steps 1 - 3 for other handset if required.

If the registration fails, Registration Failed appears in the display. Try the steps above again.

CHANGING THE DIGITAL SECURITY CODE

ADDITIONAL

INFORMATION

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 45

[ 46 ]

NOTE ON POWER SOURCES

Battery replacement and handling

Warning

To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden battery model and Uniden adapter model specifically designated for this product.

Caution

• Use only the specified Uniden battery pack (BT-446).

• Do not remove the batteries from the handset to charge them.

• Never throw the battery into a fire, disassemble them, or heat them.

• Do not remove or damage the battery casing.

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 46

[ 47 ]

TROUBLESHOOTING

If your phone is not performing to your expectations, please try these simple steps first.

Symptom Suggestion

The charge LED won’t illuminate • Make sure the AC adapter is plugged into the base and wall outlet. when the handset is placed in • Make sure the handset is properly seated in the cradle. the cradle. • Make sure the charging contacts on the handset cradle are clean.

The audio sounds weak • Move the handset and/or base to a different location away from and/or scratchy. metal objects or appliances and try again.

• Make sure that you are not too far from the base.

Can’t make or receive calls. •Check both ends of the base telephone line cord.

• Make sure the AC adapter is plugged into the base and wall outlet.

• Disconnect the AC adapter for a few minutes, then reconnect it.

• Remove the base ID (see “Replacing the Base Setting” on page 19) and register the handset (see “Register the Handset” on page 41).

• Make sure that you are not too far from the base.

• If an outside call is already established, you may not be able to

make another outside call.

The handset doesn’t ring or • Charge the batteries in the handset for 15-20 hours by placing the receive a page. handset on the base or charging cradle.

• The handset may be too far away from the base unit.

• Place the base unit away from appliances or metal objects.

• Remove the base ID (see “Replacing the Base Setting” on page 19) and register the handset (see “Register the Handset” on page 41).

“Unavailable” appears in • Make sure that another handset not too far from the base.

the display.

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 47

Symptom Suggestion

Severe noise interference. • Keep the handset away from microwave ovens, computers,

remote control toys, wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical appliances.

• Move to another location or turn off the source of interference.

The Caller ID does not display. • The handset was picked up before the second ring.

• The call was placed through a switchboard.

• Call your local telephone company to verify your Caller ID

service is current.

Voice Message Indication •Contact your local telephone company to make sure that your does not work. telephone receives FSK message signaling.

You cannot register the •Please make sure your batteries are charged for 15-20 hours. handset at the base. (see “Register the Handset” on page 41).

• Remove the base ID (see “Replacing the Base Setting” on page 19) and register the handset (see “Register the Handset” on page 41).

The handset doesn’t communicate •Remove the base ID (see “Replacing the Base Setting” on page 19) with the other handsets. and register the handset (see “Register the Handset” on page 41).

• Make sure that you have registered all handsets.

An extra handset can’t join •Make sure 'Privacy' mode has not been activated (see page 25). the conversation.

You cannot make an intercom • Make sure that the receiving handset is not in use. call with other handset.

If you still have a problem. • Check our web site for the latest information and frequently

asked questions. www.uniden.com.au www.uniden.co.nz

[ 48 ]

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 48

[ 49 ]

INDEX

0 - 9

3-way conferencing ....................43

20 ring options ..........................15

Anykey answer............................16

AutoTalk....................................15

Banner......................................16

Battery

Preparing and charging ..............iii

Replacement and handling..........46

Booster ....................................25

Caller ID

Caller ID service ......................36

Calling ....................................39

Call Waiting ............................26

Deleting ..................................38

Storing....................................39

Using......................................39

Viewing ..................................37

Call transfer feature ....................44

Chain dialing ............................35

Clock ........................................17

Copy Phonebook ........................18

Day & Time ................................17

Deregister the handset ................19

Dial Mode ..................................18

Digital security code ..................45

DirectLink mode..........................13

Distinctive ringer........................15

E, F, G, H

Earpiece volume..........................23

Expanding your phone ................40

Hands-free conversation ..............20

Headset installation......................9

I, J, K, L

Intercom ..................................43

Insert Zero ................................17

Keypad lock ..............................21

M, N, O

Making a call ............................20

Mute ........................................24

Name Tag ..................................17

Overseas call..............................36

P, Q

Package contents..........................5

Phonebook ................................28

Editing....................................34

Erasing....................................34

Making calls ............................33

Storing....................................28

Viewing ..................................32

Receiving a call ..........................20

Redialing a call ..........................22

Ringer volume ............................23

Setting up

base unit ..................................ii

handset ..................................11

Speed dialing ............................33

T, U, V, W, X, Y, Z

Transferring a call ......................43

Troubleshooting..........................47

Voice Mail..................................27

Programming............................14

Warranty....................................50

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 49

[ 50 ]

One Year Limited Warranty Important: Evidence of original purchase is required for warranty service. Warrantor: Uniden Australia Pty Limited A.B.N. 58 001 865 498

Uniden New Zealand Limited

ELEMENT OF WARRANTY: Uniden warrants to the original retail owner for the duration of this warranty, its WDECT2300 (herein after referred to as the Product), to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. Warranty is only valid in the original country of purchase.

WARRANTY DURATION: This warranty to the original retail owner only, shall terminate and be of no further effect 12 months after the date of original retail sale. This warranty will be deemed invalid if the product is;

(A) Damaged or not maintained as reasonable and necessary, (B) Modified, altered or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorized Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as part of a system not manufactured by Uniden.

PARTS COVERED: This warranty covers for one (1) year, the Base unit and handset (WDECT2300) or base, charger and handsets. All accessories (AC Adapter etc)are covered for 90 days only.

STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, the warrantor at its discretion, will repair the defect or replace the product and return it to you without charge for parts or service. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS GUARANTEE IS IN ADDITION TO AND DOES NOT IN ANY WAY AFFECT YOUR RIGHTS UNDER THE CONSUMER GUARANTEE ACT.

PROCEDURE FOR OBTAINING PERFORMANCE OR WARRANTY: In the event that the product does not conform to this warranty, the Product should be shipped or delivered, freight pre-paid, with evidence of original purchase (eg. a copy of the sales docket), to the warrantor at:

Customers in other States should ship or deliver the Product freight pre-paid to their nearest Uniden Authorized Repair Centre (Contact Uniden for the nearest Warranty Agent to you).

WARRANTY

UNIDEN AUSTRALIA PTY LIMITED SERVICE DIVISION UNIDEN NEW ZEALAND LIMITED SERVICE DIVISION

345 Princes Highway, Rockdale NSW 2216 150 Harris Road, East Tamaki, Auckland Fx (02) 9599 3278 Fx (09) 274 4253

www.uniden.com.au www.uniden.co.nz

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 50

[ 51 ]

NOTE

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 51

[ 52 ]

NOTE

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 52

[ 53 ]

NOTE

UP349BH (WDECT2300) ENG OM 1/5/05 1:19 PM Page 53

Optional Cordless Handset and Charging Cradle

For use with Multi Handset Cordless Systems: WDECT2300/ WDECT2315/ WDECT2355 Series

Call Transfer

CallerID

No Phone Jack Needed

Additional Handset & Charger

Expand Your System!

WDECT2305 HANDSET & CHARGER

UPZZ01349BC

Easily expand your cordless phone system by adding the WDECT2305 Handset and Charger*. The WDECT2305 gives you the mobility you need to stay connected with friends and family. Place this handset and charger in any convenient location, no need for an extra phone jack! Another innovation from Uniden, the company that bring outstanding wireless communication products to people's lives throughout the world.

* Operates with

Multi Handset Cordless Systems: WDECT2300/ WDECT2315/ WDECT2355 Series

AVAILABLE AT PARTICIPATING RETAIL STORES

UP349BH (WDECT2300) ENG OM 5/23/05 9:49 AM Page 54

Uniden WDECT 2300, WDECT 2315, WDECT 2315+1 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual