uriillerf VS2000KR
RF REMOTE CONTROLLED
VEHICLE SECURITY SYSTEM
Operating Guide
150 Hams Road,
East Tarnaki,
Auckland
Phone: 64-9-273 8383
Fax; 84-S-274 0009
PATENTED, 2-STAGE, PRE-INTRUSION, ELECTROMAGNETIC SHOCK SENSOR
This VS2000XR is equipped with a 2-stage, pre-intrusion, electromagnetic shock
sensor. If the vehicle is lightly tapped, the first stage sensor will cause the alarm
siren to "chirp.“ This feature provides a pre-intrusion warning to would-be thieves.
If a harder impact is made to the vehicle, the second stage sensor will activate the
alarm and sound the siren., ' ,
' I '
PATENTED, 2-STAGE, PRE-INTRUSION,
GLASS BREAK SENSOR (BUILT-IN)
If a window is tapped, the alarm will "chirp" to warn off would-be thieves. If the
window is broken, however, the alarm will be triggered. The glass break sensor
discriminates between environmental noises and the sound of breaking glass
and comes with a remote microphone.
ALARM DURATION, SIREN AND FLASHING LIGHT
If the alarm is triggered, it will sound four 30-second cycles with a 10-second pause
between cycles. For example, if the door is opened by an intruder, the alarm will
automatically sound for 30 seconds. If the door has not been shut before the end of
the 30-second cycle, the alarm will continue to sound for three more cycles and then
stop sounding. During this time the lights wilt flash in 40-second cycles with no
pause. If any of the other sensors are triggered, or the same door is closed and then
reopened, the process will begin again,
FOUR-FUNCTION LED
The alarm brain red LED has four useful functions:
• The RF transmitter-receiver can be tested by pressing the transmitter button.
If the alarm brain LED comes on, the transmitter-receiver is working properly.
• When in valet mode, the LED will flash 1.5 seconds on, 0.5 second off.
This alerts you to the fact that the alarm is currently off. It also gives the
appearance to would-be thieves that the alarm is armed.
• When the VS2000XR is fully armed, the LED will flash 0.5 second on, 1.5 seconds
off, as a warning to would-be thieves that your vehicle is protected by an alarm.
• When the VS2000XR is neither armed nor in the valet mode, the LED will be off,
DOMELIGHT SUPERVISION OUTPUT (optional)
For added protection at night or in dark parking lots, the interior domelight turns on
for 15 seconds when disarming.
RADIO PROTECTION
Your VS2000XR provides a special option for protecting valuable electronic
equipment in your vehicle, such as a CB, cellular phone or stereo. An attempt to
remove a piece of protected equipment will trigger the alarm.
V.E.T. SWITCH & OPERATION CHART
Valet Mode is useful when unloading groceries, or servicing the car. To activate the
valet mode, turn the ignition key on and press the V.E.T. switch once. Mow the alarm
will not arm. If you wish to deactivate the valet mode, turn the ignition on and press
the V.E.T. switch once. Mow the alarm can he armed.
Emergency disarm is a back-up method of disarming the alarm in case the
transmitter is lost or stolen. To disarm the alarm, first open a door. The alarm will
begin to sound. Turn the ignition key on and then press the V.E.T. switch once.
Temporary disarm can be used to temporarily disarm the alarm if the alarm Is
programmed for automatic arming. This is useful when leaving the car for a short
period of time such as during a stop at a gas station. To operate, turn off the ignition
key and press the V.E.T. switch once before opening any door. If you change your
mind and wish to leave the car for an extended time, press the transmitter button to
arm the alarm. The temporary disarm feature is automatically disengaged once the
ignition is turned on.
V.E.T.
SWITCH
FUNCTIONS
STEP 1
STEP 2
STEP3
STEP 4
LED
STATUS
ACTIVATE
VALET
DISARM THE
ALARM
TURN IGNITION
SWITCH ON
PRESSV.EX
SWITCH ONCE
TURN IGNmON
SWITCH OFF
ALARM iS NOW IN
VALET MODE
LONG FU^SH ON
^NOTE 3)
Valet
V: Mode
DEACTIVATE
VALET
TURN IGNITION
SWITCH ON
PRESS V.E.T,
SWITCH ONCE
TURN IGNITION
SWITCH OFF
ALARM CAN NOW
EE ARMED
led JS OFF LED 13 OFF LED IS OFF
P, Emergency
disarm
EMERGENCY
DISARM
THE ALARM IS
ALREADY ARMED
OPEN DOOR
(SIREN WILL
SOUND)
TURN IGNITION
SWITCH ON
PRESS V.ET. SWITCH
ONCE. ALARIv! IS
DISARMED
__ Temporary
'" disarm
TEWIPORARY(ITIME)
DISARM OF AUTOMATIC
ARMING [SEE NOTE U£}
DISARM THE ALARM
TURN IGNITION
SWITCH FROM ON
TO OFF
PRESS V.E.T.
SWITCH ONCE
(NOTE 4)
LEAVE CAR. ALARM
WILL NOT ARM FOR
THIS ONETIME
ONLY
NOTE 1; AUTOMATIC ARMING - Alarm will arm automatically 15 seconds after the last door
is shut. However, if you wish, you can arm the alarm manually after the last door is
shut, by pressing the transmitter button once.
NOTE 2: Two ways to remove the 'lemporary disarm of automatic arming" feature:
(1) Close ail doors and press the transmitter button once. The alarm will "chirp"
and arm.
(2) Turn the ignition key from off to on, then back to off. The alarm will go back to the
“automatic arming" mode.
NOTE 3: When the VS2000XR is fully armed, the LED vdli flash 0.5 second on, 1.5 seconds
off. When in valet mode, the LEO will flash 1.5 seconds on, 0.5 second off. This
protects the car in valet mode, as a thief v/ili see the Hashing LED and assume the
alarm is armed. .
NOTE A: Press the V.E.T. switch once before opening any door.
OWNER'S MANUAL
CONGRATULATIONS
From the moment you purchased this VS2000XR Vehicle Security System, you
became a part of the UNIDEN family. You started taking advantage of over 23 years
of advanced security engineering. You joined a team of engineers, technicians,
designers, and people like yourself who know how important protecting your car is.
You discovered the UNIDEN difference.
This difference is important because the VS2000XR is more than an alarm. It is
complete peace of mind. It is knowing that your car is protected around the clock by
its own security guard— one that never sleeps, never takes a break.
But even the best security systems will not work correctly without careful installation.
For greatest security, installation by your professional UNIDEN dealer is strongly
recommended. He understands both his alarms and your needs, and will work hard
to ensure the V&200DXR does its job for you.
Welcome to the family: UNIDEN, your dealer, and you!
NOTICE
The information and specifications printed in this manual are current at the time of
publication. However, the UNIDEN policy is one of continual development and
improvement. For this reason, UNIDEN reserves the right to change specifications
without notice.
Copyright© 1993 UNIDEN. All rights reserved. This material may not be
reproduced or copied, in whole or in part, without the written permission of
UNIDEN.
This Vehicle Security System is protected by patents in U.S.A., Great Britain,
Germany and Taiwan, and patents are pending in Japan and Korea.
IMPORTANT
I -.i ■
I
:1, ¡-.1
.-■I
Installation of a sophisticated vehicle security system like the VS2000XR is a very
complicated procedure. For best results, please talk to your UNIDEN dealer about
professional installation. i
NOTE: This alarm is designed to protect your entire car and its contents. But
remember that every car is different, and it may be necessary to add sensors or
accessories not included with this alarm system. Also, even though this alarm
offers a high level of security and convenience, the level of protection and the
features your alarm offers depend on how it was installed. Therefore, please ask
your dealer to clearly explain the protection and features of your alarm after
installation. i
The VS2000XR alarm system contains many innovative features and unique
functions. Please read the operation manual carefully in order to understand all of
the protection and convenience features that are offered.
--
LiMUED ymRHANrr
1) Uniden Vehicle Security Alarms are warranted against detects in rnaterial and workmanship
for 12 months from the date of sale to the original purchaser. To validate this Warranty, the
Warranty Registration Card must be completed and returned to Uniden within 10 days from
the date of purchase. This Warranty does not cover battohes. Uniden's obligation under
this Warranty shail be limited to the freo-of-charge repair (or replacement at Uniden's sole
discretion) of the faulty componGnt(s), v/hich Uniden finds to be defective in material or
workmanship under normal use and service.
Unidon (N2) Ltd. are the distributors of Uiis alarm system and not an alarm installer. Every
effort has been made to maintain a high standard of authorised installers, but does not
guarantee the quality of the installation.
This warranty is extended to the original consumer purchaser only (non-transferable).
2) This warranty is void if damage is caused by, or attributed to, Acts of God, physical or
electrical misuse or abuse, neglect, repair or alteration without the expressed written
consent of Uniden, if installed by an unauthorised Uniden dealer, instailer or purchaser
(except VS230), improper or abnormal usage, damage by water, faulty instaliation,
unauthorised repair or improper testing, if used with accessories not approved by Uniden, or
if for any other reason Uniden determines that such equipment is not operating properly as
a resuit of causes other than poor workmanship or defective material of the product.
Charges will be rendered if damages can be attributed to any of the above reasons or if the
warranty period has expired or it the warranty registration card has not been registered.
3) THE OBUGATION OF UNIDEN SHALL BE LIMITED TO THE REPAIR OH
REPLACEMENT ONLY. -
IN NO EVENT SHALL UNIDEN EE LIABLE FOR ANY SPECIAL, COLLATERAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR (i) BREACH OF ANY OF THE
PROVISIONS HEREOF, INCLUDING, WITHOUT LIMITATION, PROVISIONS
REGARDING WARRANTIES, GUARANTEES, AND/OR INDEMNITIES; OR (¡1) ANY
CLA.iMS BY THE PURCHASER CONCERNING THE GOODS WITHOUT LIMITATION,
CLAIMS FOR LOSS OF GOODWILL, LOSS OF PROFIT OH REVENUES, LOSS OF USE,
COST OF REMOVAL, INSTALLATION OR REINSTALLATION, PERSONAL INJURY OF
ANY KIND TO THE PURCHASER OR ANYONE ELSE, THEFT OR DAMAGE TO THE
VEHICLE OR IT'S CONTENTS, AND/OR ANY INABILITY ON THE PART OF THE
CONSUMER PURCHASER TO USE THE EQUIPMENT. THIS WARRANTY IS NOT AN
INSURANCE POLICY AGAINST LOSS.
4) THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER W'ARRANTIES, WHETHER
EXPRESSED OR IMPLIED, OR ARISING BY LAW, CUSTOM, OR CONDUCT,
INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND/
OR FITNESS FOR ANY PARTICULAR PURPOSE, THIS GUARANTEE IS IN ADDITION
TO AND DOES NOT IN ANYWAY AFFECT YOUR RIGHTS UNDER THE CONSUMER
GUARANTEES ACT.
5) Uniden makes no other expressed warranty for this security product. No agent,
representative, dealer or employee of Uniden has the authority to increase or alter the
obligations or limitations of the Warranty,
6) Uniden's policy is one of continued development and Improvement For this reason, Uniden
reserves the right to change specifications without notice and without incurring any
obiigation to similarly alter products previously purchased.
7) For Warranty repair, return the product froight prepaid to:
UNIDEN (N2) LTD., 150 Harris Road, EastTamaki, Auckland
A copy of the original sales receipt must be included. To help expedite the repair/
replacement of the product, please remember to include a detailed description of the
problem experienced, together with a return address and contact phone number.
OPERATING THE VS2000XR
AUTOMATIC DOOR LOCK/UNLOCK AND FLASHING LIGHTS
Your VS2Û00XR offers the convenience of automatically locking and unlocking your
car’s doors and flashing the lights when the car is armed and disarmed. This may require
the addition of certain optional accessories, and you should discuss with your
professional UNIDEN dealer about whether or not you wish to have them installed with
your alarm.
This manual assumes you are using the power door lock control and flashing light
features of your VS2000XR. If you decide not to use these features, just disregard any
references to them.
ARMING THE VS2000XR
If active arming is selected, the alarm will arm instantly after pressing the transmitter's
button #1. A 'CHIRP' will be heard, the parking lights will flash once and the car doors
will lock to signify that the alarm is armed.
If passive arming is selected, the alarm will automatically arm itself and lock the car
doors 15 seconds after all doors are dosed. A 'CHIRP" will be heard and the parking
lights will flash once after the last door is closed, to confirm that alarm is arming. During
the delay period of 15 seconds, you can temporarily stop the arming of VS2C00XR simply
by opening a door. This lets you re-enter the car without having to first disarm the alarm.
When finished, close the door and the alarm will recommence arming.
In either case, if you do not hear a chirp or see the flashing of the parking lights, the alarm
is informing you that a door has not been closed properly and therefore the alarm won't
arm. This remarkable patented fail-safe feature stops you from walking away thinking
your car is protected when it is not. {Your UNIDEN professional installer can turn this
■CHIRP'off, if you desire.)
DISARMING THE VS2000XR
If passive arming is selected, first press the transmitter's button #1 (the alarm will chirp j
twice, parking lights will flash twice and the car doors will unlock). Then, open a door ^
within 15 seconds (If a door is not opened within 15 seconds, the alarm will rearm itself).
Finally, turn ON the ignition key to stop rearming . This VS2000XR's patented 3-step
disarming process prevents accidental disarming.
if active arming is used, you can choose Auto rearm or Permanent disarm mode,
in auto rearm mode, the alarm will rearm itself unless a door is opened within 15
seconds after pressing the transmitter's button #1. In Permanent disarm mode, pressing
the transmitter’s button #1 will disarm the alarm permanently. In either mode, two chirps
will be heard, two flashing parking lights will be seen and the car doors will unlock after
pressing the transmitter's button #1.
CAR LOCATOR AND TAMPER INDICATOR WHILE DISARM
Two long flashes show the car's location when the alarm is disarmed by the transmitter.
The VS2000XR will nohfy the owner of any prior attempt to break into the car.
If the alarm has been triggered, the lights will flash seven times [instead of twice) when
the transmitter is used to disarm the|alarm. Switching on the ignition will reset the memory.
EMERGENCY CALL FOR HELP (PANIC MODE)
You can sound the siren by turning off the ignition key and holding down transmitter
button #l for three seconds. The siren will begin to sound, chasing away would-be
attackers and alerting neighbors. However, the range of the transmitter may vary; see
Trouble Shooting section, item 2,
QUIET iVlCDE
Quiet Mode allows you to use the transmitter to temporarily arm or disarm the alarm without
chirps. By pressing Button if2 and then, within 10 seconds, pressing button #1, the alarm will
either arm or disarm without chirping for that one time only. When you arrive home at night
and want to arm your alanm without disturbing your neighbor, Quiet Mode lets you aim your car
without the awakening siren chirps. ,
2nd CHANNEL OUTPUT (optional)
Pressing button #2 of your transmitter for 3 seconds triggers the second channel output from
your alarm. This output can be used to operate optional accessories such as automatic boot
release, etc. This output is operable when the ignition key is OFF. Therefore, accidentally
pressing the 2nd button will not open the boot.
TROUBLE SHOOTING
Your VS200GXR is an extremely reliable vehicle security system. In most cases, the
rare operational difficulties are the result of a weak transmitter battery or an open car
door. Below are guidelines for solving the majority of the problems you may
experience, if after foliovring these guidelines you have not found the problem,
contact your professional installer immediafely. '
1. Wo siren sound or chirp when transmitter button is pressed for arming or disarming:
a. Check if the Red wire has pcv/er, white the Black wire is properly grounded.
b. Replace the transmitter battery and check the clips for proper polarity.
c. Check that all doors are closed.
2. Transmitter works in some areas and notin other areas:
This is probably due to excess RF activity in that area (usually just a short time and only while you
are in Uiat area, depending on the type of the activity), it is only temporary and won't affect the alarm
in other areas.
3. Alarm sounds for no apparent reason:
Be sure that the transmitter button is not being held dovm loo long, or something in your pocket or
purse is not pressing against the transmitter button. The receiver may also be picking up
interference Irom a nearby airport or military base, low-flying plane or other sources. Such
interference is temporary,
4. Alarm does nofarm manually or automatically but the doors niti lock/unlack when the
transmitter is pressed. When ignition is off, LED has a long flash (1.5 sec. on, 0.5 sec. oft).
When ignition ¡son, LED is oft.
A, The alarm was accidentally switched to valet mode,
B, Turn the ignition on, press the V.E.T. switch once, then turn the ignition off. Alarm can now be armed.
NOTE 1: If the alarm still does not function properly after checking the V.E.T. switch, consult the UNIDEN
NOTE 2: Under no circumstances should you make any repairs or adjustments to any component of the
dealer where you purchased the product for further advise.
transmitter or receiver. Unauthorized repairs or adjustments to any components will void the
warranty. However, you may change the transmitter battery by yourself, if needed, as shown
below. _
CHANGING THE TRANSMITTER BATTERY
1. Unscrew the small screw from the transmitter's back.
2. Replace the battery, MAKE SURE THE POSITIVE AND
NEGATIVE BATTERY ENDS CORRESPOND
CORRECTLY TO THE POSITIVE AND NEGATIVE
BATTERY CLIPS.
3. Place back the front cover, taking care not to break the LED.
4. Place back the screw, turning it in tight enough to hold the case
together, but not so tight that the case cracks.
/ЕЛТТЕНТ(РлП Ыо. SEA172)
ÍMSEFr;ECO?y:,EaPOU=tirfl
SEA177
ACCESSORIES
INCLUDED
Ask your dealer for more information!
OPTIONAL
REMOTE CONTROL
Model SEA-177
Two transmitters included.
Get one for everyone
who uses the car.
Arms and disarms the
alarm from up to 150
feet away.
PATENTED, 2-STAGE,
PRE-INTRUSION,
ELECTROMAGNETIC
SHOCK SENSOR
Model SEA85B
Detects impact/shock of vehicle.
Totally non-directional. Provides pre
intrusion warning and intrusion outputs.
BACKUP SIREN
Model SEA400
Emits an ear-piecing and
extra-loud 128-dB blast to
frighten off thieves. Even
with car battery disconnected.
FLASHING LED
Model SEA111
Attractive, bright LED shows arm and
disarm, valet, and transmitter operation.
DOOR LOCK/UNLOCK ACTUATOR
SEA169 SEA170
Automatically locks and unlocks the
car's doors when the remote control
button is pressed.
GARAGE DOOR OPENER
SEA179
RF receiver use as an output to
control garage door, home lights, or
alarm control panel to be operated
using the RF transmitter SEA177.
PATENTED, 2-STAGE,
PRE-INTRUSION,
MICROV/AVE
SENSOR
SEA133
Features dual stage trigger which
provides Pre-intrusion Alert even
before anyone enters the car.
PIN SWITCHES
Model SEA864
Heavy-duty, adjustable
pin switches protect
boot and bonnet. Heavy-duty contacts
assure long life, rustproof operation.
REMOTE
MICROPHONE
Remote microphone plugs
into the alarm’s brain and
may be mounted inside the car.
V.E,T. SWITCH
Allows disarming of
VS2000XR if remote
control is lost or stolen.
MOTIONA/IBRATION SENSOR
SEA860
Detects motions such as jacking up
or towing.
ARM/MEMOR y BEEPER
SEA863
"Beeps" when armed to warn of prior
break-in.
RELAY
SEA8S2
MULTI-TONE SIREN
SEA173
FILË: DrRlMANUALAfl03M-U0.Ptó5/APftigS3
ORDER PART# 760-76iV653 tor UO VSEOOOXH
Loading...