Uniden VS1000X, VS1000XR Operating Manual

r

uniderr VS1000XR

RF REMOTE CONTROLLED

VEHICLE SECURITY SYSTEM

Operating Guide

U11iclen New Ze~1~~~aIbi<O1It~:d;

. . .-. ?\.\ ,!';"'j;)),j';j;rr':~~)!£\jj,j;"j~j~"It",;!t~

150 HarrisRoad,
EastTamaki,

Auckland
Phone:[phone]

Fax: [phone]

PATENTED, 2-STAGE, PRE-INTRUSION,
ELECTROMAGNETIC SHOCK SENSOR

This VS1000XR is equipped with a 2-stage, pre-intrusion, electromagnetic shock
sensor. If the vehicle is lightly tapped, the first stage sensor will cause the alarm
siren to "chirp." This feature provides a pre-intrusion warning to would-be thieves. If
a harder impact is made to the vehicle, the second stage sensor will activate the

alarm and sound the siren. .

NOTE: The alarm will not have this pre-intrusion feature if your alarm is

programmed to use current sensing.

ALARM DURATION, SIRENAND FLASHING LIGHT

If the alarm is triggered, it will sound for four 28-second cycles with a 1a-second
pause between cycles. For example, if a door opening is detected, the alarm will

automatically sound for 28 seconds. If the door has not been shut before the end of
the 28-second cycle, the alarm will continue to sound for three more cycles and then

stop sounding. During this time the lights will flash in 38-second cycles with no
pause. If any of the other sensors are triggered, or the same door is closed and then
reopened, the process will begin again.

FOUR-FUNCTION LED

The alarm brain's red LED has four useful functions:
. The RF transmitter-receiver can be tested by pressing the transmitter button. If

the alarm brain LED comes on, the transmitter-receiver is working properly.

. When in valet mode the LED will flash at intervals of 1.5 seconds on, 0.5 second

off. This alerts you to the fact that the alarm is currently off. It also gives the
appearance to would-be thieves that the alarm is armed.

. When the VS1000XR is fully armed, the LED will flash at intervals of 0.5 second

on, 1.5 seconds off, as a warning to would-be thieves that your vehicle is
protected by an alarm.

. When the VS1000XR is not armed nor in the valet mode, the LED will be off.

PASSIVE OR ACTIVE ARMING

.PASSIVE ARMING: The alarmwill automatically arm itself 15seconds

after turning off the ignitionkey and closing that lastopened door.

. ACTIVE ARMING: The alarm will only arm after pressingthe transmitter's

button#1 providedignition key is off and all doors are closed.

CHIRP DISABLE

Arming or disarming chirp confirmation can be turned off. However, the chirp disable
feature will not disable the pre-intrusion chirp and full siren blast.

. CHIRP CONFIRMATION
. NO CHIRP CONFIRMATION

PASSIVE OR MANUAL DOORLOCK SELECTION
(PASSIVE MODE ONLY)

. Auto

. Active Lock: The doorlocks will not lock unless the remote transmitter is used.

Lock: The doorlocks will lock each time the alarm rearms by itself automatically.

\{E. T. SWITCH & OPERATION CHART

Valet Mode is useful for unloading groceries, or servicing the car if passive arming is

being used. To activate the valet mode, turn the ignition key on and press the V.ET.
switch once. Now the alarm will not arm. If you wish to deactivate the valet mode,

turn the ignition on and press the V.ET. switch once. Now the alarm can be armed.
Emergency disarm is a back-up method of disarming the alarm in case the

transmitter is lost or stolen. To disarm the alarm, first open a door. The alarm will
begin to sound. Turn on the key and then press the V.ET. switch once. Now the

system is disarmed.
Temporary disarm can be used to temporarily disarm the alarm if it is pr09rammed

for passive armin9. This is useful for leaving the car for a short period of time such
as a stop at a gas station. To operate, turn off the ignition and press the V.ET.
switch once before opening any door. If you change your mind and wish to leave the
car for an extended time, press. the transmitter button to arm the alarm. The
temporary disarm feature is automatically disengaged once the ignition is turned on.

V.E.T. v.Valet

.Mode

SWITCH

FUNCTIONS

STEP 1

STEP 2

STEP 3

STEP 4

LED

STATUS

NOTE 1: PASSIVE ARMING - Alarm will arm automatically 15 seconds after the last door is

NOTE 2: There are two ways to remove the "temporary disarm of passive arming" feature:

NOTE 3: When the VS1000XR is fully armed, the LED will flash at intervals of 0.5 second on,

NOTE 4: Press V.E.T. switch once before opening any door.

ACTIVATE
VALET VALET

DISARM THE
ALARM

TURN IGNITION PRESS V.E.T.
SWITCH ON SWITCH ONCE

PRESS V.E.T.
SWITCH ONCE

TURN IGNITION
SWITCH OFF.
ALARM IS NOW IN DISARMED
VALET MODE

LONG FLASH ON

(NOTE 3)

shut. However, if you wish, you can arm the alarm manually after the last door is
shut, by pressing the transmitter button once.

(1) Close all doors and press the transmitter once. The alarm will "chirp" and arm.
(2) Turn the ignition key from off to on, then back to off. The alarm will go back to the

"passive arming" mode.

1.5 seconds off. When in valet mode, the LED will flash at intervals of 1.5 seconds
on, 0.5 second off. This protects the car in valet mode, as would-be thieves will see
the flashing LED and assume the alarm is armed.

DEACTIVATE

TURN IGNITION
SWITCH ON

TURN IGNITION

SWITCH OFF

ALARM CAN NOW
BE ARMED

LED IS OFF

E.Emergency

.disarm

EMERGENCY
DISARM

THE ALARM IS
ALREADY ARMED

OPEN DOOR
(SIREN WILL SWITCH FROM ON

SOUND)

TURN IGNITION PRESS V.E.T.
SWITCH ON SWITCH ONCE

PRESS V.E.T. SWITCH
ONCE. ALARM IS

LED IS OFF LED IS OFF

T.Temporary

.disarm

TEMPORARY(1 TIME)
DISARMOFPASSIVE

ARMING(SEENOTE1&2)

DISARM THE ALARM

TURN IGNITION

TO OFF

(NOTE 4)
LEAVE CAR. ALARM

WILL NOT ARM FOR
THIS ONE TIME
ONLY