SSE 30
Corded Telephone
For more exciting new products please visit our website:
Australia: www.uniden.com.au
Important Safety Instructions
• This unit is NOT waterproof. DO NOT expose this unit to rain or
moisture.
• Do not use this product near water, for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
• Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS!
What’s in the Box?
Telephone Cord
Owner’s Manual
SSE30 base with corded handset
• If any item is missing or damaged, contact your place of purchase
immediately. Never use damaged products!
• Need help? Get answers at our website:
www.uniden.com.au for Australian model.
2
Installing Your Phone
Connect the Corded Handset
1. Use the coiled cord to connect the corded handset to the connector on
the bottom of the base.
2. Connect the the telephone cord to the TEL LINE jack and plug the other
end to a standard telephone wall socket.
Test the Connection
Pick up the corded handset from the base. You should hear a dial tone.
When you get a dial tone, make a quick test call.
Wall Mount Installation
You can mount the SSE 30 on the wall.
# To prevent the handset from falling out of the cradle, while the
phone is hanging on the wall, you must reverse the hook. Please
refer to the image below
.
Hook Position
(Desk)
1. Push the handset hook up and out of the
slot on the base with your thumb, rotate
the hook 180°, and replace it back on
the slot.
2. Slip the mounting holes, located at the
back of the base, over the screw heads
and firmly slide down to secure into
place.
Hook Position
(Wall Mount)
Hook Switch
Hook
3
Handset & Base Callouts
BOOST
Volu me
TEL Line Jack
4
RESET
Key Pad
MUTE
REDIAL
FLASH
Mic
Handset Cord Connector
Ringer LED
Ringer
Operation
Answer a Call
When there is an incoming call, the phone rings and the ringer LED
flashes. Pick up the handset to answer the call. After talking, hang up the
handset or press RESET to end the call.
Boost and Volume Control
The BOOST button helps you control the volume of the receiver. During a
conversation, press the BOOST button (the ringer LED will glow) and then
rotate the Volume Control to adjust the volume according to your liking.
Last Number Redial
Pick up the handset and press REDIAL, the phone will automatically dial
out the last dialed number.
Mute
During a call, press and hold MUTE to mute the microphone.
Flash
Call Waiting is a service that is available from your telephone service
provider. If you have opted for this ser vice from your provider, then press
FLASH and 2 to put the first caller on hold and accept the waiting call. To
return to the original caller, press FL ASH and 2 again.
Ringer
Slide the Ringer switch to OFF, to mute the ringer, which means that
the phone will not ring for any calls. However, the ringer LED will flash,
indicating an incoming call.
5
Important Information
Solving Problems
Listed below are some of the problems and the possible solutions. If you
still need help, visit our website, listed on the front cover.
General Problems Possible Solutions
No dial tone Press and release the hook switch.
Phone doesn’t ring Make sure the Ringer switch is turned
Other par ty cannot hear you Make sure the telephone cord is securely
on.
plugged in.
6
ONE-YEAR LIMITED WARRANTY
SSE 30
IMPORTANT Satisfactor y evidence of the original purchase is
required for warranty service Please refer to our Uniden website for any
details or warranty durations of fered in addition to those contained below.
Warrantor
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden
Aust”).
Terms of Warranty
Uniden Aust w arrants to the ori ginal retail purcha ser only that the SSE3 0(“the
Product”), will be free from defects in materials and craftsmanship for the
duration of the warranty period, subject to the limitations and exclusions set
out below.
Warranty Period
This warranty to the original retail purchaser is only valid in the original
country of purchase for a Product first purchased either in Australia or New
Zealand and will expire one (1) year from the date of the original retail sale.
If a warranty claim is made, this warranty will not apply if the Product is
found by Uniden to be:
(A) Damaged or not maintain ed in a reasonable mann er or as recommende d
in the relevant Uniden Owner’s Manual;
(B) Modified, altered or used as part of any conversion kits, subassemblies
or any configurations not sold by Uniden Aust;
(C) Improperly installed contrary to instructions contained in the relevant
Owner’s Manual
(D) Repaired by someone other than an authorized Uniden Repair Agent in
relation to a defect or malfunction covered by this warranty; or
(E) Used in conjunction with any equipment, parts or a system not
manufactured by Uniden.
Parts Covered
This warranty covers the Product and included accessories.
7
User-generated Data
This warranty does not cover any claimed loss of or damage to usergenerated data (including but without limitation phone numbers, addresses
and images) that may be stored on your Product.
Statement of Remedy
If the Product is found not to conform to this warranty as stated above,
the Warrantor, at its discretion, will either repair the defect or replace the
Product without any charge for parts or ser vice. This warranty does not
include any reimbursement or payment of any consequential damages
claimed to arise from a Product’s failure to comply with the warranty.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount
to a major failure.
This warranty is in addition to and sits alongside your rights under either
the COMPETITION AND CONSUMER ACT 2010 (Australia) or the
CONSUMER GUARANTEES ACT (New Zealand) as the case may be,
none of which can be excluded.
Procedure for Obtaining Warranty Service
Depending on the country in which the Product was first purchased, if you
believe that your Product does not conform with this warranty, you should
deliver the Product, together with satisfactory evidence of your original
purchase (such as a legible copy of the sales docket) to Uniden. Please
refer to the Uniden website for address details. You should contact Uniden
regarding any compens ation that may be payable for your expenses incurred
in making a warranty claim. Prior to delivery, we recommend that you make
a backup copy of any phone numbers, images or other data stored on your
Product, in case it is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Phone number: 1300 366 895
Email address: custservice@uniden.com.au
Uniden Australia P ty Ltd
Printed in China
Loading...