Pro7800N1
NVR User Manual
Admin User Name:
Admin Password:
IP Address:
System Name:
User Information
1. Menu Operation ............................................................................................................4
1.1 Main Menu .................................................................................................................4
2. Start & Shutdown System ........................................................................................ 5
2.1 Start Sub Menu ......................................................................................................5
3. Preview ............................................................................................................................8
4. IP Channel Setting ......................................................................................................9
4.1 Add IPC Automatically ....................................................................................... 9
4.2 Add IPC Manually ................................................................................................11
4.3 Channel Parameters Modification .................................................................12
4.4 Modify IPC Parameters .....................................................................................14
4.5 Delete IPC ...............................................................................................................15
5. System Configuration Setting ................................................................................16
5.1 Device Setting ........................................................................................................16
5.2 Channel Parameters Setting ............................................................................17
5.2.1 Display Setting ............................................................................................18
5.2.2 Video Parameters .....................................................................................19
5.2.3 Schedule Record .......................................................................................21
5.2.3.1 Precise Video Backup. .................................................................. 22
5.2.3.2 Record Time ....................................................................................23
5.2.3.3 Advanced Record .......................................................................... 24
5.2.4 Motion Detection ......................................................................................25
5.2.5 Video Lost ...................................................................................................28
5.2.6 Tampering Alarm ......................................................................................30
5.2.7 Video Mask Setting ..................................................................................33
5.3 Network ...................................................................................................................35
5.3.1 Network Setting .........................................................................................36
5.3.1.1 Advanced Setting ............................................................................38
5.3.2 DDNS Setting .............................................................................................39
5.3.3 NTP Setting .................................................................................................40
5.3.4 Email Setting ..............................................................................................41
5.3.5 Management Platform ............................................................................42
5.4 Alarm & Exception ..............................................................................................43
5.4.1 Alarm Input ..................................................................................................44
5.4.2 Alarm Output .............................................................................................46
5.4.3 Exception .....................................................................................................47
5.5 Account Setting ...................................................................................................48
5.5.1 User Information Setting ........................................................................49
5.5.2 User Online Checking .............................................................................50
5.6 System Administration ......................................................................................51
5.6.1 Device Log ...................................................................................................52
5.6.2 Stream Info .................................................................................................53
5.6.3 HDD Setting................................................................................................54
5.6.4 System Update ..........................................................................................55
5.6.5 Auto Reboot ...............................................................................................56
5.6.6 Recovery Configuration .........................................................................57
6. PTZ Control ...................................................................................................................58
7. Record.. ............................................................................................................................60
8. Manual Snapshot .........................................................................................................60
9. Video Playback ............................................................................................................61
10. Display Setting ...........................................................................................................63
11. Video Backup ...............................................................................................................64
12. Alarm Setting ..............................................................................................................65
13. File Manager ................................................................................................................66
14. Image Setting ..............................................................................................................67
15. Screen Aspect Ratio/Segmentation ...................................................................67
Table Of Contents
4 5
1. Menu Operation
1.1 Main Menu
The Main Menu gives you access to all of the NVR’s key functions.
With your mouse, right click on the preview screen during a live
view to pull up the Main Menu.
2. Start/Shutdown System
2.1 Start Sub Menu
The Start Sub Menu displays when you hover over the Start
button and allows you to Power O, Reboot, Login, Logout,
access the User Guide, set the Device Time and adjust Volume.
Main Menu
Start Sub Menu Screen
Login Screen
• Power O: To begin, switch on the power source and press the
button to start up the device. Press Power O to shut down
device.
• Login: Click Login to open the login screen. You can input your
own username and password or login with the default user. The
default user is admin, the default password is left blank.
6 7
• User Guide: After logging into the NVR System, the User
Guide screen will appear and ask you to set it up as it takes
you through the following steps:
• Language: Choose a language from the drop-down
menu. The default language is English. Click Next to
save changes and continue.
• Network Setting:
• IP: Input the Network’s IP address.
• Subnet Mask: Input the corresponding IP Subnet Mask.
• Default Gateway: Input the corresponding gateway address.
• Click Next to save and continue logging in to the NVR
interface.
• Display Setting: Select the appropriate Video Format and
Resolution to match your display. The default Video Format is
NTSC and the default Resolution is 1280×1024 (60HZ). Click
Next to save and continue.
Language Screen
Display Setting Screen
Network Setting Screen
8 9
3. Preview
The Preview screen will display after logging in, showing the
current video feeds for each individual channel.
4. IP Channel Setting
4.1 Add IPC Automatically
Select IP Channel Setting from the Main Menu and click the
Search button. All the IPCs that are connected to the NVR
will appear and you can modify the settings for each.
Preview Screen
IP Channel Setting Screen
10 11
IP Channel Setting Screen
Manual IPC Entry Screen
When you click the check box in front of any of the listed IP
cameras, the IP camera will be added to the channel window
on the right. Clicking All will add all of the listed IP cameras
to the channel window on the right. Click Save to continue.
4.2 Add IPC Manually
You can also manually add the IP Cameras if you already
know the address by typing it into the box.
• Select the channel and click the check box in front of
Enable.
• Select relevant Protocol.
• Input the Address of the IP Camera.
• Input the Port Number.
• Select the proper Stream Type.
• Select Network Type.
12 13
• Select the Play Mode.
• Input the User Name associated with the IP Camera.
• Input the Password of the IP Camera.
• Click Save.
4.3 Channel Parameters Modification
Open the Channel menu to modify channel parameters.
Channel Screen
• Enable: Select the relevant channel and check Enable to
enable a channel.
• Protocol: Select a protocol type from: Onvif Standard
protocol, I8 Private protocol, I9 Private protocol and RTSP
protocol.
• Address: Edit and modify the IP address manually.
• Port: Edit and set the port number.
• Stream Type: Select either Main Stream+Sub Stream or
Sub Stream.
• Network Type: Select either TCP or UDP.
• User: Input the username.
• Password: Fill in the password.
14 15
4.4 Modify IPC Parameters
Double-click the channel settings that need to be modified
under Channel and fill in the relevant parameters, click
Modify to save.
4.5 Delete IPC
Mark the IPC parameters that needed to be removed and
click the button.
IPC Screen
Delete IPC Screen
16 17
5. System Configuration Setting
5.1 Device Setting
The NVR’s main configuration settings are located under
Device in Setting on the Main Menu.
• Device Info: Check and modify the basic device information.
• System Version: View the system version number.
• PTZ Setting: Set the parameters for the Pan-Tilt-Zoom (PTZ)
dome cameras.
• DST Setting: Set the Daylight Savings Time (DTS) settings for
the system.
5.2 Channel Parameter Setting
Select Channel to modify the settings and features for each
of the monitoring cameras in your system.
Setting Screen
18 19
5.2.1 Display Setting
Select Display Setting to adjust how each camera is displayed
on the screen.
5.2.2 Video Parameters
Modify the Video Parameters for each camera.
Display Setting Screen
Video Parameters Screen
• Channel: Choose the channel you would like to modify.
• Local Camera Name: Enter the camera’s name you would
like displayed on the channel.
• Time Format: Choose from a 24-hour or 12-hour time display.
• Date Format: Choose how you would like the date to display.
• OSD Position: Select the place on the screen where the
camera’s name and time will display.
• Image Setting: Adjust the access devices brightness and
contrast.
Note: Except for the Channel setting, other options only
available for privacy protocol equipment.
20 21
• Channel: Select the channel number for each channel.
• Encoding Type: Choose either Main Stream or Sub Stream.
• Stream Type: Choose to either stream the Audio and Video
from the camera or just the Video.
• Resolution: Choose the resolution supported by the camera.
• Bitrate Type: Choose either CBR or VBR bitrate.
• Bitrate: Select appropriate bitrate value for this condition.
• Frame Rate: Choose frame rates from the drop-down menu.
The default is full frame rate.
• Video Quality: Select the quality of video you would like
displayed. The default is highest quailty.
• I Frame Interval: Set the video frame interval. The default
is 25.
Note: Video Setting will be directly modified for the IP camera
parameters and is only valid for private protocol channels.
5.2.3 Schedule Record
Use Schedule Record to determine when each channel is
going to be recording. Use the Copy To feature to transfer
the settings to other channels.
Schedule Record Screen
22 23
5.2.3.1 Precise Video Backup
If you would like to set a precise video backup time,
first make sure the check box in front of All Day Recording
is not checked, as this will highlight all available times. Once
it is unchecked, hold down the left mouse button and drag
the cursor to select the area to define the preferred
recording time. Double-click to set the start and end times.
left mouse button and drag the cursor to select the area to
define the preferred recording time. Double-click to set the
start and end times.
5.2.3.2 Record Time
Click Record Time under Setting to set a recording schedule.
You can set 8 periods during one day.
Precise Video Backup Screen
Schedule Screen
24 25
5.2.3.3 Advanced Record
The Advanced Setting screen allows you to adjust for Pre
Recording and Post Recording.
5.2.4 Motion Detection
Set the motion detection settings for each video channel and
use Copy To to transfer the settings to other channels.
Note: IP Cameras must support motion detection for this
feature.
Setting Screen
Motion Screen
26 27
• To turn on motion detection for a particular channel, click
the check box in front of Enable Motion Detection.
• Use your mouse to select the areas on the camera’s video
display that you would like to be covered with motion
detection under Area Settings.
• Adjust the motion detection’s Sensitivity to determine how
much motion must register on the system before you are
alerted.
• Set Arm Schedule for the motion detection.
• Set Linkage to define the Trigger Mode the system will use
in response to a motion detection. Upload to Center will
upload alarm information to the platform. and Trigger
Recording will turn on recording for selected channels as
a response.
Area Settings Screen
Linkage Screen
28 29
5.2.5 Video Lost
Set an alarm notification in case the camera loses video. Use
Copy To to transfer the settings to other channels.
• Click the check box in front of Enable Video Lost to turn
on the feature.
• Set the Arm Schedule.
• Select the Linkage to define the Trigger Mode in the
event of a loss of video.
Video Lost Screen
Linkage Screen
30 31
5.2.6 Tampering Alarm
This screen enables the triggering of an alarm when a camera
is tampered with.
Note: IP Cameras must support tampering alarm.
• Click the check box in front of Enable Video Tampering to
activate this feature.
• Define the tampering alarm areas under Area Settings
using your mouse.
• Adjust the Sensitivity level.
Tampering Alarm Screen
Area Settings Screen
32 33
• Set the Arm Schedule.
• Select Linkage to define the Trigger Mode in the event of
tampering.
Linkage Screen
Video Mask Screen
5.2.7 Video Mask Setting
Use Video Mask to block o the portion of the camera’s
video that you wish to exclude.
34 35
Area Settings Screen
Network Screen
5.3 Network
The Network screen gives you access to your network
settings.
• Click the check box in front of Enable Video Mask to turn
on this feature.
• Define mask areas under Area Settings.
36 37
5.3.1 Network Setting
Modify the basic network information on the Network
Setting screen.
• NIC: Select corresponding NIC.
• If a device is equipped with double NIC, select the right
NIC.
• If a device is equipped with double NIC without POE,
Network Setting Screen
3G Screen
the network segment of the IP Camera’s access in LAN1
should be the same as NIC1 and NIC2 of LAN2.
• If a device is equipped with double NIC with POE, the
network segment of the IP Camera’s access in the POE
ports should be the same as the NIC2.
• IP: Input the relevant IP Address number.
• DHCP: Click the check box in front of DHCP. It will
automatically input a valid IP according to the router DHCP.
• Subnet Mask: Input a relevant IP Subnet Mask number.
• Default Gateway: Input a relevant Default Gateway number.
• MAC: Displays the present MAC address.
• Remote Port: Input a relevant Remote Port number.
• HTTP Port: Input a relevant HTTP Port number, the default
is 80.
• Enable 3G: After linking up the 3G accessible equipment,
click the check box in front of Enable 3G, select the Device
Type, edit the Phone Number, select Work State, then click
OK to save:
38 39
5.3.1.1 Advanced Setting
Set advanced configuration parameters under the Advance
settings.
5.3.2 DDNS Setting
The DDNS server allows the DVR to connect to the Internet
through a PC with a fixed IP address.
• Manage Host allows the NVR to register the servers
automatically.
• Enable PPPOE function for NVR dialing.
• Click the check box in front of Enable UPnP after setting
the HTTP port and TCP port so it can match successfully.
Make sure the port number does not conflict with other
devices.
• Select the DDNS Server Type from the following options:
Dyndns, PeanutHull, NO-IP, 3322, and Dnsdynamic.
• Input the Server Name. (Sample: member.3322.org)
• Input the Port.
• Input the Username.
• Input and confirm the Password.
• Input the Domain Name.
Advance Settings Screen
DDNS Settings Screen
40 41
5.3.3 NTP Setting
NTP Settings Screen
Email Settings Screen
• Server Address: Input the IP of the NTP server.
• NTP Port: This NTP only supports TCP transmission, the
default is 123.
• Update Frequency: Input the time interval in hours for the
update frequency.
• Select Time Zone: Select from dierent time zone options.
• GMT: Make fine adjustments to the time settings.
5.3.4 Email Setting
Set up parameters so the NVR can send status messages
about motion detection or other events through email
notifications.
42 43
5.3.5 Management Platform
Set up a connection to management platforms or a WebServer.
5.4 Alarm & Exception
The Alarm screen allows you to set up alarms for the NVR
system. The NVR will alert you by sounding an alarm sound
and creating a pop-up of the live video stream when
triggered by events such as motion detection, video loss or
hard disk drive problems.
Management Platform Screen
44 45
5.4.1 Alarm Input
The Alarm Input enables alarm processing, sets the alarm
schedule and selects the trigger mode.
Alarm Input Screen Linkage Screen Screen
46 47
5.4.2 Alarm Output
Sets the alarm output delay and alarm schedule.
5.4.3 Exception
Sets the alarm event types, alarm audio type and alarm
display settings for the monitor.
Alarm Output Screen
Alarm Exception Screen
48 49
5.5 Account Setting
View and modify details of the user accounts in your system.
5.5.1 User Information Setting
Add, modify or delete users and define user permissions
under Account Setting.
Account Screen
Account Setting Screen
50 51
5.5.2 User Online Checking
Check to see the current status of each online user’s
connection.
User Online Screen
5.6 System Administration
The System screen allows you to modify system settings.
System Screen
52 53
5.6.1 Device Log
Check the device logs according to the video type and data
time.
5.6.2 Stream Info
View the band width of data streaming for each channel.
• Main Type: Sorts by All Types, Alarm, Exception and
Operation.
• Sub Type: Defines sub categories for the corresponding main
types.
• From: Define a starting time for the log display.
• To : Define an ending time for the log display.
• Export: Export and all query results.
Device Log Screen
Stream Info Screen
54 55
5.6.3 HDD Setting
Check the capacity and free space of the Hard Disk Drive
(HDD) and format if needed.
5.6.4 System Update
Browse and select an upgrade file to upgrade the system
hardware and view progress.
HDD Setting Screen
System Update Screen
56 57
5.6.5 Auto Reboot
Enable or disable the NVR system to reboot one time, or set
a daily or weekly rebooting schedule.
5.6.6 Recovery Configuration
Export or import a recovery file.
Auto Reboot Screen Recovery Configuration Screen
58 59
6. PTZ Control
PTZ (Pan Tilt Zoom) is located on the Main Menu and can be used to
set the controls for cameras equipped with the Pan-Tilt-Zoom feature.
• Preset: Rotate the camera to a specific angle and position and
save the setting by selecting a preset number in the drop down list.
• Cruise: Set the camera’s rotation speed by selecting a cruise
number in the drop-down list and clicking the gear button; a
screen will pop up with more settings. To recall a cruise setting,
select a cruise number in the drop-down list and click the
arrow button. To delete a cruise setting, select the cruise
number in the drop-down list and click the X button.
On the Cruise screen, set preset, preset name, residence time
and cruise speed, then click Add to create a new cruise preset.
Click Delete to clear the preset.
• Track: Set the PTZ camera to automatically detect, follow and
record video of moving persons or objects.
• Select a track number in the drop-down list.
• Click Track Start to set the PTZ camera operation, and
Track Stop to set the track in memory.
• To recall the track setting, select the track number in the
drop-down list and click the arrow button.
PTZ Control Screen
Cruise Screen
60 61
7. Record
Record, located on the Main Menu, allows you to set the system to
record based on a schedule, or you can manually turn recording on or
o for all channels or for individual channels.
8. Manual Snapshot
Select Capture on the Main Menu and click the camera button in the
lower right corner of the screen to take a snapshot of the preview
screen. The snapshot pictures can be viewed under File Manager.
9. Video Playback
Select Playback on the Main Menu to view and re-play recorded video
from each individual channel.
Record Screen
Video Playback Screen
62 63
• Channel Select: Select the channel you would like to playback.
• Date Select: Select the date of playback desired.
• Playback Interface: Use the toolbar at the bottom of the
Playback screen to control playing progress, as shown in the
table below.
10. Display Setting
Display Setting is located in the Main Menu and allows you to
adjust the following settings.
• Language: Choose a language (Simplified Chinese, English,
French, etc.).
• Auto Logout: Determine how many minutes the system must
be idle before it will automatically logout.
• Display: Adjust the brightness, contrast, saturation, hue,
transparency, etc. of the video screen display.
• Resolution: Select from resolution options to match your
display.
• Enable SEQ: Click the check box in front of Enable SEQ and
click the Setting button to select the channel. Selected
channels will be displayed in a rotation on the viewing screen.
• Rotation Interval: Set the rotation interval time in seconds.
Button Operation Button Operation Button Operation
Backward Play Stop
Slow Down Fast Forward
Frame
By
Frame
Play
Snapshot Backup Full Screen
Volume
Dispaly Setting Screen
64 65
11. Video Backup
Backup in the Main Menu allows you to copy the backup video
files from the hard disk to an external storage device, such as a
USB drive.
• After you connect the USB, click Refresh to test whether USB
devices are identified. If they are, the setting screen will
display.
• Select a single channel or check All to select all channels for
backup.
• Using the From and To fields, select a start and stop time for
the backup.
• Select a file type: i8 or AVI.
• Click the Start button to begin the backup process. Click
Unmount USB after finishing.
12. Alarm Setting
Alarm in located in the Main Menu and all the device’s alarm
information will appear on the list.
Backup Screen
Alarm Setting Screen
66 67
13. File Manager
The File Manager, located in the Main Menu, lists all video and
capture images stored on the hard disk drive as well as any video
or capture files stored on an attached external storage device
such as a USB drive.
14. Image Setting
Adjust the brightness, contrast, saturation and hue on the video
image through Image Setting located on the Main Menu.
15. Screen Aspect Ratio/Segmentation
Set the Screen Aspect Ratio on the Main Menu according to
the NVR version: 4, 6, 8, 9, 16, 20 or 25 screens. The default
Screen Aspect Ratio of the device is 4:3.
File Manager Screen
Aspect Ratio Screen
Image Setting Screen
Contact Us:
URL: support.uniden.com/pro-support
Pro Support
Phone: (888) 851-6966
Available M-F 8:30-5:30 CST
Customer Support
Phone: (800) 297-1023
Available 24/7
3-Year Limited Warranty
All Pro•Series products – including DVR/NVR, cameras and security HDDs – come with
a 3-year limited warranty to demonstrate Uniden’s commitment to your product’s reliability.
For more information, visit support.uniden.com/pro-support.
Pro•Series Customer Service
Uniden provides Pro•Series Customer Service oering quality support when you need
it including:
• Direct Pro Support
• Customer Support 24/7
• Videos
• Remotely view all your devices
from your smartphone or tablet
• Playback video
• Capture images
• Receive support directly
from your device
FREE Uniden Pro Wired App Full Mobile remote control
and setup from iPhone®, iPad®, iPod touch® and Android™
devices. Receive alerts via Email or Notification. SYSTEM
REQUIREMENTS: Router with Internet access and available
Ethernet Port, iPhone®, iPad®, iPod touch® or Android™ device.
Email: prosupport@uniden.com
Facebook: https://www.facebook.com/
UnidenAmerica
Twitter: https://twitter.com/
uniden_america
• FAQs
• Specifications
• Feedback Portal
Loading...