Uniden GMR1595-2CK User Manual

GMR1588-2CK/GMR1595-2CK

*Range may vary depending on environmental and/or topographical conditions.

•

15 GMRS / 7 FRS Channels

•

142 Privacy Codes (CTCSS Tone
and DCS Code)

•

Up to 15 Mile Range*

•

Direct Call

•

Scramble

•

143 Group Codes

•

Silent Mode

•

Internal VOX Circuitry

•

10 Selectable Call/Ring Tone Alerts

•

Backlit LCD Display

•

Optional Headset Accessories

•

Headset Jack

•

Roger Beep

1 Antenna
2 PTT (Push-To-Talk) Button
3 Power Boost Button
4 Weather/Alert Key
5 D-call Key
6 Menu/group Key
7 Speaker
8 Volume Setting Nob

9 Up/Down Button
10 Headset Jack
11 Channel Tone/Scan Key
12 Monitor Key

13 Microphone
14 DC IN 9V
15 Channel Indicator
16 Sub Code Indicator
17 Alert Indicator
18 Receive Indicator
19 Miss Indicator
20 Battery Level Indicator
21 Scramble Indicator
22 VOX Indicator
23 Call Indicator
24 Charging Contacts

Congratulations on your purchase of the Uniden
GMR1588-2CK/GMR1595-2CK (General Mobile
Radio Service) radio. This lightweight, palm-sized,
radio is a state-of-the-art device, equipped with
many valuable features. Use it at sporting events,
to stay in contact with family and friends, hiking,
skiing, outdoors, or in a neighborhood watch for
vital communication.

PACKAGE CONTENTS

Your package contains two GMR1588-2CK /
GMR1595-2CK radios, two rechargeable NiMH
battery packs (#BP38), two AC adapters (#AD-

1004), two charging cradles (#RC1581), two belt
clips and this reference guide.You can operate the
unit using the rechargeable NiMH battery pack or
4 AAA alkaline batteries (not included).
To order the following optional accessories, visit our
web site @www.uniden.com or call 1-800-554-3988,
Mon-Fri, 8 a.m. to 5 p.m. CST.

Use only Uniden accessories.

• NiMH Battery Pack - #BP38

• Charging Cradle - #RC1581

• VOX Headset - #HS910/HS915

• AC Adapter - #AD-1004

• DC Adapter - #DC-1002

GMRS LICENSE

The GMR1588-2CK/GMR1595-2CK radio operates

on the General Mobile Radio Service (GMRS)

frequencies when using Channels 1-7 and

channels 15-22.You must have a GMRS license

issued by the Federal Communications

Commission to legally use these channels. For

licensing information and application forms, visit

the FCC online at: www.fcc.gov/wtb/uls or call

the FCC hotline at 1-800-418-3676. If you have

any questions, you can contact the FCC direct at

1-888-225-5322. No license is required for

operation on channels 8-14 or operation on any

channel in Canada.

INSTALL THE BATTERY

Your GMR1588-2CK/GMR1595-2CK radio uses a

supplied NiMH battery pack or 4 AAA alkaline

batteries (not included).

To install the NiMH battery pack:

1) Make sure the radio is off.

2) Release the battery cover clip, then remove the

battery cover.

3) Put the NiMH battery pack in the battery

compartment. Be sure to follow the instructions

USING THE RADIO

SETTING UP GROUP MODE

USING THE RADIO BATTERY

LEVEL AND LOW BATTERY ALERT

This radio has a battery level meter that indicates
the status of the batteries. When the battery level is
low, BATT appears and the battery level meter icon

flashes. Recharge the NiMH battery pack
immediately or, if you are using the alkaline
batteries, replace the alkaline batteries in order to
continue using the radio.

Warning! To avoid the risk of personal injury or
property damage from fire or electrical shock, only
use the Uniden accessories specifically designated
for this product.

GMR1588-2CK/GMR1595-2CK RADIO

CHARGING THE RADIO

If you use the rechargeable NiMH battery pack, two
GMR1588-2CK/GMR1595-2CK radios can be
charged directly or by using the supplied charging
cradle.

Charge by Using the Radio

1) Connect the AC adapter or optional DC adapter

to DC IN 9V jack of the radio and connect it to
the appropriate power source.

2) Charge the battery pack for 16 hours until the

battery indicator stop flashing.

Using the Charging Cradle

1) Connect the AC adapter or optional DC adapter

to DC IN 9V jack of the charging cradle and
connect it to the appropriate power source.

2) Set the charging cradle on the desk or tabletop,

and place the radio in the charging cradle with
the keypad facing forward.

3) Charge the battery pack for 16 hours until the

battery indicator stops flashing. Then remove the
radio from the charging cradle after completing
charging.

Note:

• Use only the supplied battery and AC adapter or

approved DC adapter from Uniden.

• Charge time may vary depending on the battery

life remaining.

• Do not recharge alkaline batteries. Doing so can

create a safety hazard or damage the radio.

• For fastest charging, turn off the radio before

charging.

written on the battery pack’s label. Installing the

battery pack incorrectly will prevent the unit from

operating.

4) Align the battery cover tabs with the tab holes

on the radio, then replace the cover clip.

In order to get the most out of your new radio, read
this reference guide completely before attempting to
operate the unit.

Turning the Radio On and Adjusting the Volume

1) Rotate vol/off clockwise until it clicks, and set
volume to a comfortable listening level.

2) To turn off the radio, rotate vol/off
counterclockwise until it clicks.

Adjusting the Sound (Key Beeps)

Your radio sounds a beep each time you press a
key (except for PTT and Power boost).
To turn this sound off, press and hold d-call while
turning on the radio. Repeat this step to turn the
sound on.

Choosing a Channel

Your radio has 22 channels and 142 Privacy codes
you can use to talk to others. In order to speak to
someone, both your radios must be set to the same
channel and Privacy code.

To choose a channel:

Press

ch tone/scn, then press ▲ or ▼ to increase

or decrease the channel number displayed.

Note: Channels 1-7 and 15-22 have a typical range
of up to 10 miles, or 15 miles when you press
Power Boost. Channels 8-14 have a typical range
of up to 5 miles.You can see an indication of the
range as you change channels. HI appears when
you select channels 1-7 or 15-22, and LO appears
for channels 8-14.

Warning! The range of channels 1-7 and 15-22 can
be boosted only when you use NiMH batteries.
When you press Power boost while using alkaline
batteries, the range is not boosted.

• Batteries must be installed for operation, even
from external power.

• If battery power is low, you cannot operate the
radio even using external power. Let the
batteries charge before using. If you try to
transmit while power is low, the radio
automatically turns off.

In order to use Group Mode you need to initialize a
couple of settings in your radio:

• Set the radio to Group Mode

• Set a Group Code

• Set a Ring Tone

• Set a Unit Number

• Set a "Nickname"

Setting the Radio to Group Mode

To set the radio to Group Mode, which enables
Direct Call, Auto Channel Change and All Call,
press and hold menu/grp for 2 seconds. The radio
displays oF GRUP. Press ▲ to display on GRUP,
then press menu/grp to advance to setting the
Group Code.

Note: In group mode, you cannot receive
transmissions from other radios unless they are
also set to the same channel and group code.

Setting the Group Code

Set the group code for your radio group from 0-142.
Everyone in your group must select the same
group code in order to communicate with each
other.

1) Press and hold menu/grp for 2 seconds. The
radio displays on GRUP.

2) Tap menu/grp. The radio displays Gnnn (n is a
number). Press ▲ or ▼ to select the group
number.

3) Press PTT or Power boost to return to normal
operation, or continue to the next section.

Setting the Ring Tone

This setting selects the tone you hear when
someone places a direct call to you.

1) Press and hold menu/grp for 2 seconds, then
tap menu/grp two times until the radio displays
n RING.

2) Press ▲ or ▼ to select the desired ring sound.
With each press, you hear a sample of the
selected tone.

3) Press PTT or Power boost to return to normal
operation, or continue to the next section.

Setting the Unit Number

Each radio in your group needs to be set to a
unique unit number, from 1-16.

1) Press and hold menu/grp for 2 seconds, then
tap menu/grp three times until the radio
displays n

- - - -

(or your current nickname).

2) Press ▲ or ▼ to select the desired unit number.

3) Press menu/grp to confirm the setting and exit
the group setting menu.

Setting Your Nickname

Your nickname appears on other units’ displays
when you make a All Call or direct call. This is also
the name that appears on other radio displays
when someone wants to make a direct call to you.
When no nickname is set, the unit number appears.

1) Press and hold menu/grp for 2 seconds, then
tap menu/grp four times until the radio displays

n

- - - -

(or your current nickname) with the first

place in the nickname flashing.

2) Press ▲ to select the letter, then ch tone/scn to
advance to the next letter until you have entered
your nickname.

3) Press menu/grp to confirm the setting and exit
the group settings menu.

Using Group Mode

Group mode lets you make direct calls to other
people in your group without alerting the entire
group and also lets you quickly change everyone in
your group to another channel from a single radio.
Before using group mode, follow the instructions in
"Setting Up Group Mode" on every radio in your
group. Then, to record the unit ID and everyone’s
nickname in every radio, send a call to "All" from
each radio one time (see "Sending a Direct Call").

Sending a Direct Call

Direct Call lets you call everyone in your group at
once, or call a single person in your group without
anyone else in the group knowing. It is like a
"speed dial" directly to the person(s) you want to
talk to.

To call everyone in your group, press d-call in
group mode. The radio flashes ALL. Then, press
d-call again. Everyone in your group receives a call
"chirp" for about 3 seconds. When the chirp ends,
begin your conversation.

Note: When you make a direct call to "all," your
radio also sends out your nickname or ID so that it
will show up in the call list for everyone in your
group.

To call one person in your group, without having
other people know, press d-call in group mode.
Then, use ▲ or ▼ to select the person you want to
call and press d-call again. Your radio sounds
tones for 3 seconds as it sends the call. When the
selected person answers, you can begin your
conversation.You can silence the call tones at any
time by pressing PTT or Power boost.

Your conversation remains private between you and
the person you called until 15 seconds after your
last conversation. Then, your radio automatically
exits private mode.

Automatically Changing Channels

Auto Channel Change lets you easily coordinate a
channel change for everyone in your group. You
might want to do this when you find you are getting
a lot of interference on your current channel. Or,
you can use this feature to change from a low­power channel (8-14) to one of the high-powered
channels (1-7, 15-22) if you need more range (or to

USING THE RADIO IN STANDARD MODE

Use the radio in standard (not group) mode when
you need to be able to communicate with radios
that do not have the group feature.

Choosing a Privacy Code

You can select a Privacy Code from 1-142 for each
channel. oFF (OFF) indicates no Privacy code
selected and your radio can receive a signal
regardless of the code settings of the transmitting
radio.

1) Press ch tone/scn twice. The Privacy code
indicator flashes.

2) Press ▲ or ▼ to increase or decrease the
code. You can also select oFF.

3) Press ch tone/scn again.

Note: Only tones 1-38 are standard across radio
brands. Other settings might differ from brand to
brand. See the specifications for the specific tones
used for each setting.

Channel Scan Feature

Your GMR1588-2CK/GMR1595-2CK radio has a
channel scan feature that lets you easily scan all
22 channels. When an active channel is detected,
the radio pauses on that channel until the channel
is clear. Then after a 2-second delay, the radio
resumes scanning. Pressing PTT or Power boost
while the scan is paused on a channel lets you
transmit on that channel.

To turn on channel scan:

Press and hold

ch tone/scn until SCAN appears.
The channel number changes as the radio rapidly
cycles through the channels.

To turn off channel scan:

Press

d-call, PTT, Power boost, wx/alert or

menu/grp, or press and hold ch tone/scn for 2

seconds.

Talking on Your Radio

To talk to others using the radio:

1) Press and hold

PTT or Power boost and speak
in a clear, normal voice about 2-3 inches away
from the microphone. While you transmit, TXHI
or TXLO appears on the display according to
the type of channel. To avoid cutting off the first
part of your transmission, pause slightly after
pressing PTT or Power boost before you start
talking.

2) When you finish speaking, release PTT or
Power boost.You can now receive incoming
calls. While receiving, rx appears on the display.

Note: When you press Power boost, BOOS
appear on the display. The radio transmits at
maximum power when a GMRS channel is
selected. If Power boost is continuously pressed,
1 minute after you start pressing Power boost the
transmission stops and you hear a boost timeout
error tone.

Monitor Mode Feature

Your GMR1588-2CK/GMR1595-2CK radio lets you
listen for weak signals on the current channel at the
press of a key.

To turn on the Monitor Mode:

• For brief listening, press mon. MON appears

and rx icon flashes.

• Press and hold mon for 2 seconds until two

beeps sound for continuous listening. The

receiver circuit stays open, so you hear both the

noise and weak signals.

To turn off Monitor Mode:

Press

mon to return to the previous mode. The

mon and rx icons disappear.

Navigating through the Normal Menu

To access the advanced features of the GMR1588­2CK/GMR1595-2CK, your radio has a Menu
function.

1) To enter the menu, press menu/grp.

2) Additional presses of menu/grp advances you
through the menu. After the last menu item, the
radio exits to the previous mode.

3) Other ways to exit the Menu function are:

a. Press PTT, Power boost, mon, d-call,

wx/alert, or ch tone/scn.

b. Wait 10 seconds until the radio automatically

returns to previous mode.

Setting Scramble

Scramble allows you to make a private
conversation. No one listening to your conversation
can understand what you are talking about. Be sure
that the person you are calling also sets their radio
to the scramble feature.

To set Scramble:

1) Enter the menu.

SCRM appears and the current

setting flashes.

2) Press ▲ to display on SCRM. scrm appears.

Note: You can only communicate using scramble
between two compatible Uniden radios.

Voice Operated Transmission

Your GMR1588-2CK/GMR1595-2CK radio has a
user selectable Voice Operated Transmitter (VOX)
that can be used for automatic voice transmissions.
The VOX feature is designed to be used with a
headset with a microphone. Transmission is starts
when you speak into the microphone instead of
pushing the PTT and Power boost button.

To select the VOX level:

1) Enter the menu. Advance through the menu until
VOX appears. The current level (OFF, 1-5)
flashes. Level oF (OFF) disables VOX, while
levels 1-5 set the sensitivity of the VOX circuit.

2) Press either ▲ or ▼ to set the desired VOX
sensitivity level. Use level 1 for increased
sensitivity to voice in normally quiet
environments, and use a higher level to reduce
undesired activation in very noisy environments.

Transmitting a Call Tone

Your GMR1588-2CK/GMR1595-2CK radio is
equipped with 10 selectable call tones that are
transmitted when you press d-call in standard
mode.

•

Vibrate Reminder
(GMR1595 Only)

•

Power Boost Button for
Maximum Range

•

All Call

•

Auto Channel Change Call

•

Battery Charger

•

Battery Level Meter

•

Channel Monitor

•

Channel Scan

•

Group Scan

•

Keypad Lock

•

NOAA Emergency /
Weather Channels

•

Emergency Weather Alert

•

DC IN 9V Jack

a low-power channel if you need longer battery
life).

To start an auto channel change, on any radio in
the group tap ch tone/scn. The current channel
and CHCX appears. Use ▲ or ▼ to select the
target channel. You can check whether the selected
channel is clear. Then press d-call.
Your radio chirps for about 10 seconds while it
sends out the channel change signal. As each
radio receives the channel change signal, it chirps
once, then changes to the new channel.

To ensure all radios make it to the new channel, we
recommend you:

• Make sure you are in an open environment,

where the radio will get the best range.

• Optimize range during the channel change

signal by raising the radio over your head to give

the best possible height.

• Do a "roll call" on the new channel after the

move to be sure no one was left behind. If you

missed someone, return to the previous channel

and issue the signal again.

Key LockScramble VOX Level Call Tone Silent Mode

OFF, 1-5

1-10

ON-OFFON-OFF ON-OFF

Channels 15 GMRS/7 FRS/7 Weather

Sub Codes 38 Sub-Audible Tones

104 DCS Codes

Operating Frequency

GMRS/FRS: 462.5500 - 467.7125 MHz

WX: 162.4000 - 162.5500 MHz

Power Source NiMH Battery Pack (BP38) or

4 AAA Alkaline Batteries

Range Channel 1-7 up to 10 miles

(15 miles with Power boost

button)

Channel 8-14 up to 5 miles

Channel 15-22 up to 10 miles

(15 miles with Power boost

button)

Battery Life 12 Hours typ. - NiMH

Battery Pack (5/5/90 duty

cucle)

Frequency Chart

Ch. Freq. Cross Ref. Ch. Freq. Cross Ref.

1 462.5625 FRS & GMRS 1 12 467.6625 FRS 12

2 462.5875 FRS & GMRS 2 13 467.6875 FRS 13

3 462.6125 FRS & GMRS 3 14 467.7125 FRS 14

4 462.6375 FRS & GMRS 4 15 462.5500 GMRS 11

5 462.6625 FRS & GMRS 5 16 462.5750 GMRS 8

6 462.6875 FRS & GMRS 6 17 462.6000 GMRS 12

7 462.7125 FRS & GMRS 7 18 462.6250 GMRS 9

8 467.5625 FRS 8 19 462.6500 GMRS 13

9 467.5875 FRS 9 20 462.6750 GMRS 10

10 467.6125 FRS 10 21 462.7000 GMRS 14

11 467.6375 FRS 11 22 462.7250 GMRS 15

CTCSS Chart (Hz)

Code Freq. Code Freq.

oFF OFF 20 131.8

1 67.0 21 136.5

2 71.9 22 141.3

3 74.4 23 146.2

4 77.0 24 151.4

5 79.7 25 156.7

6 82.5 26 162.2

7 85.4 27 167.9

8 88.5 28 173.8

9 91.5 29 179.9

10 94.8 30 186.2

11 97.4 31 192.8

12 100.0 32 203.5

13 103.5 33 210.7

14 107.2 34 218.1

15 110.9 35 225.7

© 2006 Uniden America Corporation

All rights reserved Printed in China

UTZZ01018ZZ(0)

SPECIFICATIONS

16 114.8 36 233.6

17 118.8 37 241.8

18 123.0 38 250.3

19 127.3

Tone Octal

No. Code

39 023

40 025

41 026

42 031

43 032

44 043

45 047

46 051

47 054

48 065

49 071

50 072

51 073

52 074

53 114

54 115

55 116

56 125

57 131

58 132

59 134

60 143

61 152

62 155

63 156

64 162

65 165

66 172

67 174

68 205

69 223

70 226

71 243

72 244

73 245

Tone Octal

No. Code

74 251

75 261

76 263

77 265

78 271

79 306

80 311

81 315

82 331

83 343

84 346

85 351

86 364

87 365

88 371

89 411

90 412

91 413

92 423

93 431

94 432

95 445

96 464

97 465

98 466

99 503

100 506

101 516

102 532

103 546

104 565

105 606

106 612

107 624

108 627

Tone Octal

No. Code

109 631

110 632

111 654

112 662

113 664

114 703

115 712

116 723

117 731

118 732

119 734

120 743

121 754

122 036

123 053

124 122

125 145

126 212

127 225

128 246

129 252

130 255

131 266

132 274

133 325

134 332

135 356

136 446

137 452

138 454

139 455

140 462

141 523

142 526

DCS Code List

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

Important: Changes or modifications to this unit

not expressly approved by Uniden could void your

authority to operate this unit. Your radio is set up

to transmit a regulated signal on an assigned

frequency. It is against the law to alter or adjust the

settings inside the radio to exceed those limitations.

Any adjustments to your radio must be made by

qualified technicians.

To be safe and sure:

• Never open your radio’s case.

• Never change or replace anything in your radio

except the batteries.

Your radio might cause TV or radio interference

even when it is operating properly. To determine

whether your radio is causing the interference, turn

it off. If the interference goes away, your radio is

causing it. Try to eliminate the interference by

moving your radio away from the receiver. If you

cannot eliminate the interference, the FCC requires

that you stop using the radio.

Hazardous Environments: Do not operate the

radio in hazardous environments. Explosion or fire

may result. Do not operate the radio near

unshielded electrical blasting caps.

Under certain conditions, radios can interfere with

blasting operations and may cause an explosion.

Turn your radio OFF to prevent accidental

transmission when in a blasting area or in areas

posted: "Turn off two-way radio." Construction

crews often use remote control RF devices to set

off explosives.

Care and Safety: To clean the radio, use a soft

cloth dampened with water. Do not use cleaners or

solvents because they can harm the body of the

unit and leak inside, causing permanent damage.

Use a dry, lint-free cloth to clean the battery

contacts. Do not submerge the unit in water. If the

unit gets wet, turn it off and remove the batteries

immediately.

Dry the battery compartment with a soft cloth to

minimize potential water damage. Leave the battery

compartment cover off overnight to ensure

complete drying. Do not use the radio until the unit

is completely dry.

Important: Evidence of original purchase is

required for warranty service.

WARRANTOR: UNIDEN AMERICA

CORPORATION ("Uniden")

ELEMENTS OF WARRANTY: Uniden warrants, for

one year, to the original retail owner, this Uniden

Product to be free from defects in materials and

craftsmanship with only the limitations or exclusions

set out below.

WARRANTY DURATION: This warranty to the

original user shall terminate and be of no further

effect 12 months after the date of original retail

sale. The warranty is invalid if the Product is:

(A) damaged or not maintained as reasonable or

necessary, (B) modified, altered, or used as part

of any conversion kits, sub-assemblies, or any

configurations not sold by Uniden, (C) improperly

installed, (D) serviced or repaired by someone

other than an authorized Uniden service center for

a defect or malfunction covered by this warranty,

(E) used in any conjunction with equipment or parts

or as part of any system not manufactured by

Uniden, or (F) installed or programmed by anyone

other than as detailed by the owner’s manual for

this product.

STATEMENT OF REMEDY: In the event that the

product does not conform to this warranty at any

time while this warranty is in effect, warrantor will

either, at its option, repair or replace the defective

unit and return it to you without charge for parts,

service, or any other cost (except shipping and

handling) incurred by warrantor or its

representatives in connection with the performance

of this warranty. Warrantor, at its option, may

replace the unit with a new or refurbished unit.

THE LIMITED WARRANTY SET FORTH ABOVE

IS THE SOLE AND ENTIRE WARRANTY

PERTAINING TO THE PRODUCT AND IS IN LIEU

OF AND EXCLUDES ALL OTHER WARRANTIES

OF ANY NATURE WHATSOEVER, WHETHER

EXPRESS, IMPLIED OR ARISING BY

OPERATION OF LAW, INCLUDING, BUT NOT

LIMITED TO ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE.THIS WARRANTY DOES

NOT COVER OR PROVIDE FOR THE

REIMBURSEMENT OVERPAYMENT OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow this exclusion or limitation

of incidental or consequential damages so the

above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you

specific legal rights, and you may also have other

rights which vary from state to state. This warranty

is void outside the United States of America and

Canada.

PROCEDURE FOR OBTAINING PERFORMANCE

OF WARRANTY: If, after following the instructions

in the owner’s manual you are certain that the

Product is defective, pack the Product carefully

(preferably in its original packaging). Disconnect the

battery from the Product and separately secure the

battery in its own separate packaging within the

shipping carton. The Product should include all

parts and accessories originally packaged with the

Product. Include evidence of original purchase and

a note describing the defect that has caused you to

return it.The Product should be shipped freight

prepaid, by traceable means, to warrantor at:

ONE YEAR LIMITED WARRANTYREGULATORY INFORMATION

WARNING! Read this information before using

the radio. In August 1996 the Federal

Communications Commission (FCC) of the United

States with its action in Report and Order FCC

96-326 adopted an updated safety standard for

human exposure to radio frequency

electromagnetic energy emitted by FCC regulated

transmitters.

Those guidelines are consistent with the safety

standard previously set by both U.S. and

international standards bodies. The design of the

radio complies with the FCC guidelines and these

international standards.

Never allow children to operate the radio without

adult supervision and the knowledge of the

following guidelines.

WARNING! It is up to the user to properly operate

this radio transmitter to insure safe operation.

Please adhere to the following:

Use only the supplied or an approved antenna.

Unauthorized antennas, modifications, or

attachments could impair call quality, damage the

radio, or result in violation of FCC regulations.

Do not use the radio with a damaged antenna.

If a damaged antenna comes into contact with the

skin, a minor burn may result. Please contact your

local dealer for a replacement antenna.

Body-worn Operation

This device was tested for typical body-worn

operations using the supplied belt-clip.

To maintain compliance with FCC RF exposure

requirements, Body-worn operations are restricted

to the supplied belt-clip.

For hand-held operation, the radio should be held

1 inch from the user's face. The use of accessories

that do not satisfy these requirements may not

comply with FCC RF exposure requirements and

should be avoided.

For more information about RF exposure, please

visit the FCC web site at www.fcc.gov.

RF EXPOSURE INFORMATION

Covered under one or more of the following

U.S. patents:

4,684,870 4,734,049 5,203,015 5,214,789

5,491,745 5,497,508 5,517,677 5,557,606

5,574,994 5,610,946 5,613,201 5,625,870

5,627,876 5,628,059 5,634,196 5,634,205

5,678,176 5,697,096 5,717,312 5,722,070

5,787,345 5,901,341 6,021,326 6,084,861

6,163,691 6,195,415 6,353,730 6,839,550

Uniden America Service

4700 Amon Carter Blvd. Fort Worth, TX 76155

[phone], 7:00 a.m. to 7:00 p.m. CST,

Monday through Friday: 9:00 a.m. to 5:00 p.m. CST,

Saturday, Sunday and Holidays (except

Thanksgiving and Christmas).

To select a call tone:

1) Enter the menu. Advance through the menu until
CALL appears. The current call tone number
(1-10) flashes.

2) Press ▲ or ▼ to increase or decrease the
number to the desired call tone. Each tone will
be heard through the speaker.

To transmit the selected call tone, press d-call. The
selected tone is transmitted for a fixed length of
time. Call Tone is cancelled if you press PTT or
Power boost.

Setting Silent Mode

When you turn on the silent mode, all incoming
calls are muted: the radio blinks the display
backlight, the channel indicator, SLNT and call icon
to alert you to an incoming call. If you do not
respond to the call within 15 seconds, the backlight
turns off, and the call icon will blink until there is no
signal. The GMR1595 will also vibrate to remind
you that you missed a call. Silent mode is disabled
for 15 seconds when you transmit, receive, or press
any other button.

To set the silent mode:

1) Enter the menu. Advance through the menu until
the

SLNT appears. The current setting flashes.

2) Press ▲ to display on SLNT.

Note: To prevent unwanted silent alerts, be sure to
use a Privacy code or group code whenever you
use the Silent mode feature.
You can hear the received voice when you turn on
channel scan and an active channel is detected
even during silent mode.

Missed Call Alerts

If you receive an incoming call while silent mode is
on and do not respond, the radio will turn on the
Missed Call icon. If you are using the Group Mode,
the radio will also indicate the person who made
the call.

The GMR1595 will additionally remind you of a
missed call by vibrating every minute after the call
for 3 minutes.

Key Lock

To lock the keypad:

1) Enter the menu. Advance through the menu until
LOCK appears. The radio displays oF LOCK.

2) To switch Key Lock from oF (OFF) to on (ON),
press ▲.

3) To confirm the setting, press menu/grp. The
radio returns to the current mode.

Note: If you exit the setting mode before confirming
your selection by pressing menu/grp, Key Lock is
set to oF (OFF).

To unlock the keypad:

1) Turn off the radio by rotating

vol/off

counterclockwise until it clicks.

2) Turn on the radio again by rotating vol/off
clockwise until it clicks. The keypad is unlocked.

Automatic Power Save Feature

Your GMR1588-2CK/GMR1595-2CK radio has a
unique circuit designed to dramatically extend the
life of the batteries. If there is no transmission nor
an incoming call within 3 seconds, your radio
switches to the Power Save mode. The radio is still
able to receive transmissions in this mode.

LCD Backlight

The LCD Backlight automatically turns on when
any key (except the PTT and Power boost button)
is pressed. The LCD remains lit for 10 seconds
before turning off.

Roger Beep

Roger beep is a beep that is sent to notify the end
of transmission (both PTT and VOX transmission).
You can hear the roger beep can be heard through
the speaker when both roger beep and key beep
are on. When roger beep is on and key beep is off,
you do not hear the roger beep, but it is transmitted
to your party.

To turn the roger beep OFF, press and hold

▲

while turning ON the radio. Repeat this step to turn
the beep ON.

USING THE WEATHER RADIO

Your GMR1588-2CK/GMR1595-2CK radio can
receive weather broadcasts from the NOAA
National Weather Service. When in the Weather
Radio Alert mode, the system functions as it does
in standard mode but also monitors the selected
weather channel for alerts when not
communicating. While using the Weather Radio,
you are not able to receive GMRS communications.

1) To turn on the Weather Radio Broadcast mode,
press wx/alert. WX appears.

2) Press ch tone/scn, then press ▲ or ▼ to
increase or decrease the number to the desired
Weather Channel.

3) To exit the Weather Radio Broadcast mode,
press wx/alert. WX disappears.

• To change the channel continuously, press and
hold ▲ or ▼ for more than 1 second.

• When in the Weather Radio Broadcast mode,

you can only set the Key Lock from the Menu

mode.

Choosing an Emergency/Weather Channel

There are 7 NOAA channel frequencies available
and these frequencies are common between the
US and Canada.You need to know what frequency
is being transmitted in your location.

1) Press and hold wx/alert. The icon
appears.

2) When the unit receives a warning signal, it
beeps for 5 seconds. The icon, WX
and channel indicator blinks.

3) To turn off Weather Alert, press and hold
wx/alert. The icon disappears.

• When Weather Alert is activated, the highest

priority is given to this function. It checks the

weather alert signals every 7 seconds. When

the unit finds a warning signal, it switches to the

warning receive mode automatically.

• Weather Alert is activated even if key beep is

turned off.

NOAA Weather Radio Frequency List

Channel 1 162.550 MHz Channel 5 162.450 MHz

Channel 2 162.400 MHz Channel 6 162.500 MHz

Channel 3 162.475 MHz Channel 7 162.525 MHz

Channel 4 162.425 MHz