Thank you for choosing the Uniden EXA 8955 cordless telephone.
Features
Introduction
This phone is designed to exacting standards that provide reliability,
long life and outstanding performance.
Note: Some illustrations in this manual may differ from the
actual unit for explanation purposes.
• 900 MHz Extended Range
• Secure Digital Transmission
• Integrated Answering Device
• 10 Number Memory
• 32 Digit Redial
TO YOUR NEW PHONE
• Redial, Flash and Pause
• Pulse / Tone Dialing
• 7 Hour Talk Time
• 7 Day Standby Battery Life
• Handset Earpiece and Ringer Volume Control
• Speakerphone
• 3-Way Conference Operation
INTRODUCTION
talk flash
int'c mem
mute
abc def
jklghi
mno
tuvpqrs
oper
tone
wxyz
213
546
879
0
redial pause
ringer
chan
extended range
vol
DIGITAL 900MHz
speaker
page/int'commute
flash
redial/p
memory
ans on/off
voice memogreeting
status speaker
clock pin volune
playdelete
DIGITAL
extended range
talk batt mute
1
2
3
4
5
6
7
8
16
17
18
20
21
19
15
14
9
10
13
11
12
22
25
26
23
24
27
29
30
31
32
28
33
34 35 36 37
38
44
45
46
47
42
43
41
39
40
Controls and functions
RING TIME REC TIME
2/4/TS ANN/4/1
48
49
50 51 52 53
1. Handset antenna
2. Headset jack cover
3. Handset battery compartment
4. Handset ring switch
5. Handset speaker
6. Talk/Batt LED
7. Talk key
8. Volume down key
9. Mute key
10. Tone key
11. Redial key
12. Pause key
13. Handset microphone
14. Mute LED
15. Volume up key
16. Flash key
17. Memory key
18. Intercom key
19. Channel key
20. Ring key
21. Handset battery contacts
22. Base microphone
23. Speaker LED
24. Status LED
25. Handset retainer clip
26. Clock key
27. Pin code key
28. Delete key
29. Greeting key
30. Repeat key
31. Skip key
32. Voice memo record key
33. Base battery contacts
34. Tone key
35. Mute key
36. Speaker key
37. Page/Intercom key
38. Base speaker
39. Volume down key
40. Volume up key
41. LED display
42. Play/Stop key
43. Base antenna
44. Answer on/off key
45. Memory key
46. Redial/Pause key
47. Flash key
48. Record time switch
49. Ring time switch
50. Ring volume switch
51. Pulse-Tone switch
52. DC power input
53. Phone jack
Introduction / Features...............inside front cover
Contents
Controls and Functions ..............inside front cover
Getting Started
Read this first..........................................................3
Step 1: Checking the package contents...............4
Step 2: Setting up the base unit ...........................5
Mounting the base unit on a wall ...........8
Step 3: Preparing the battery pack .....................10
Basics
Making a call ........................................................12
Receiving a call ....................................................13
Adjusting ringer and ear speaker volume ..........14
Redialing a call.....................................................15
Mute ......................................................................16
Memory Dialing
Storing phone numbers .......................................17
Making calls with memory dialing ......................18
Erasing a stored phone number..........................19
3-way Conference Features
3-way conferencing ..............................................20
Using your EXA 8955 intercom ...........................21
Transferring a call.................................................22
OF YOUR OWNER’S MANUAL
The Integrated Answering Device
Features.................................................................23
Setting up your answering system......................24
Using your answering system .............................28
Additional Information
Changing the digital security code......................34
Installing the beltclip............................................35
Headset installation..............................................35
Note on power sources .......................................36
Maintenance..........................................................36
Troubleshooting..................................................37
Specifications.......................................................39
Index .....................................................................40
Getting Started
Basics
Memory Dialing
3-way
Conference
Features
The Integated
Answering
devise
Additional
Information
Troubleshooting
Specifications
Index
CONTENTS
This cordless telephone must be set up before use. Follow these steps;
Read this first
Step 1 (page 4)
Unpack the telephone and accessories.
Step 2 (page 5 to 9)
Next, choose the best location to set
up the base unit.
Base unit
Step 3 (page 10 to11)
Then, insert the battery pack into the handset.
You have to charge the battery pack for more
than 12 hours before using the phone.
Handset
3
GETTING STARTED
About the digital security code
This cordless telephone uses a digital security code to prevent
unauthorized access to your base unit. This security code prevents
other cordless handsets from making calls through your base unit.
A random security code will be assigned automatically between
your base unit and handset when you charge the battery pack for
the first time.
If you want to reset the security code, see page 34.
Make sure you have received the following items in the package.
Checking the package contents
If any of these items are missing or damaged, contact the
Parts Department
• Base unit • Handset • AC adapter (AD-420)
(see below).
Uniden
• Rechargeable
battery pack
(BT-905)
• This Owner's Manual
• Precautions and Important Safety Instructions
• Registration Card
Uniden Parts Department
(800) 554-3988
Hours: M-F 8:30 AM to 5:00 PM CST.
We can also be reached on the web at www.uniden.com.
• Telephone line
cord (2)
• Wall mount adapter
• Beltclip
4
Do the following steps.
Setting up the base
• Choose the best location
• Connect the base unit
• Choose the dialing mode
Choose the best location
Before choosing a location for your new phone, read the
INSTALLATION CONSIDERATIONS included in the PRECAUTIONS
AND IMPORTANT SAFETY INSTRUCTIONS brochure. Here are some
important guidelines you should consider:
Avoid heat sources, such as
radiators, air ducts, and sunlight
Avoid television sets
and other electronic
equipment
Choose a central location
Avoid noise sources such as a window
by a street with heavy traffic
Avoid microwave ovens
Avoid excessive
moisture, extremely low
temperatures, dust,
mechanical vibration, or
shock
Avoid personal
computers
Avoid other cordless
telephones
• You should charge your handset for 15-20 hours before using
the phone.
• The location should be close to both a phone jack and continuous
a power outlet which is not switchable.
• Keep the base and handset away from sources of electrical noise
such as motors and fluorescent lighting.
• Be sure there is suf ficient space to raise the base antenna
fully vertical.
• The base can be placed on a desk, tabletop or mounted on a
standard wall plate.
5
To AC outlet
To telephone outlet
To TEL LINE
To DC IN 9V
AC adapter
(supplied)
Telephone line cord
(supplied)
1
2
Route the cord.
Place the power cord so it
does not create a trip
hazard, or where it could
become chafed and create
a fire or electrical hazard.
Connect the base unit
If you want to install the base unit on the wall, see page 8.
1 Connect the telephone line cord to the TEL LINE jack and to
a telephone outlet.
2 Connect the AC adapter to the DC IN 9V jack and to a
standard 120VAC wall outlet.
3 Set the base unit on a desk or
tabletop and place the handset
on the base unit.
Then raise the antenna to a
vertical position.
6
Use only the supplied AD-420 AC
PULSE
TONE
adapter. Do not use any other AC
adapter.
Connect the AC adapter to a
continuous power supply.
Place the base unit close to the
AC outlet so that you can unplug the
AC adapter easily.
Polarity of the plug
If your telephone outlet isn't modular,
contact your telephone company for
assistance.
Modular
Choose the dialing mode
Depending on your dialing system, set the TONE/PULSE switch as
follows:
If your dialing system is Set the switch to
Tone
Pulse
If you aren't sure of your dialing system
Make a trial call with the TONE/PULSE switch set to
If the call connects, leave the switch as is; otherwise, set to
TONE
PULSE
TONE
.
PULSE
.
7
Standard wall plate mounting
AC adapter
Wall plate
AC outlet
Mounting the base unit on a wall
This phone can be mounted on any standard telephone wall
plate.
1
2 - 7
1 Snap the wall mount
adapter into the
notches on the base.
2 Plug the telephone
line cord to the
TEL LINE jack and the
AC adapter to the
DC IN 9V jack.
3 Plug the telephone
line cord into the
telephone outlet.
4 Wrap the AC adapter
cord inside the
molded wiring
channel. Then wrap
the cord around the
strain relief notch.
5 Plug the AC adapter
into a standard
120VAC wall outlet.
6 Raise the antenna to a
vertical position.
7 Align the mounting
slots on the base. with
the mounting posts on
the wall. Push in and
down until the phone
is firmly seated.
8
TOP
3/16 in.
3-15/16 in.
8 On the base unit, pull the
Handset retainer
handset retainer out of the slot.
Rotate it clockwise
180 degrees.
9 Flip the retainer from front to
back. Slide it back into the slot
so that the lip of the retainer is
up and the oval is down. The
retainer holds the handset
in place,
Direct wall plate mounting
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting
location, that could cause a hazard when inserting screws into
the wall.
• Try to mount your phone within 10 - 15 feet of a working phone
jack to avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of
the base and handset.
9
1 Insert two mounting screws
into the wall, (with their
appropriate anchoring device),
3-15/16 inches apart. Allow
about 3/16 of an inch between
the wall and screwheads for
mounting the phone.
2 Refer to steps 1 through 8 on
page 8 to mount the telephone.
Red
status
LED
Black
Use only Uniden Battery
Preparing the battery pack
BT-905.
Charge the battery pack for more than 12-15 hours before you start
using your phone.
1 Remove the battery cover.
2 Connect the battery pack
connector with the correct
polarity (black and red wires),
then insert the battery pack
into the battery compartment.
3 Slide the battery cover forward
until it snaps into place.
4 Place the handset on the base.
Make sure that the
LED of the base unit lights, and
charging begins. Charge the
battery for at least 12-15 hours.
You can place either side up
for charging the battery.
“
status
”
10
Battery use time (per charge)
From fully charged
• Seven hours coutinuous use.
• Seven days when the handset is in the standby mode.
Even when the battery
pack is not being used, it
will gradually
discharge over a long
period. For optimum
performance, be sure to
return the handset to the
base unit after a
telephone call for
charging the battery.
Rechargeable batteries
have a memory effect that
reduces standby and talk
time. To avoid this
memory effect, on a
monthly basis, use the
phone until the Battery
lamp blinks. Then charge
the battery for 15 hours.
When the battery charge becomes low
When the voltage of battery pack in the handset is very low and
needs to be charged, the phone is programmed to eliminate
functions in order to save power. If the battery charge becomes low
Battery LED blinks. If the phone is in use, the handset beeps.
Complete your conversation as quickly as possible and return the
handset to the base unit for charging.
Cleaning the battery contacts
To maintain a good charge, it is important to clean the battery
contacts on the handset and base unit about once a month. Use a
pencil eraser or other contact cleaner.
Do not use any liquids or solvents.
11
From the handset
chan
ª
•
/tone
pause
Making a call
talk
talk
speaker
speaker
redial/p
The phone number can be
up to 32 digits.
If the
talk
LED never stop
flashing, place the handset
on the base for at least
three seconds and make a
call again.
From the base
1 Press . The
talk
LED blinks.
2 Dial the phone number.
3 To hang up, press or return the
handset to the base.
1 Press . The
blinks.
speaker
LED
2 Dial the number on the keypad.
3 When you finish the call, press
to hang up.
Other Operations
To Do this
To improve reception Press on the handset.
To adjust the ear speaker volume Press or during the call.
To temporarily switch to tone dial Press . The following
(When the base is set to pulse numbers dialed will be sent as
mode) tone dialing.
To enter a pause within dialing Press . (Handset)
sequence Press . (Base)
BASICS
12
From the handset
status
LED
Receiving a call
talk
talk
speaker
speaker
Handset on the base
From the base
1 Phone rings. The
talk
LED flashes.
2 Pick up the handset and begin speaking.
3 Press or return the handset to the
base to finish the call.
Handset off the base
1 Phone rings. The
2 Press and begin speaking.
talk
talk
LED flashes.
3 To hang up, press or return the
handset to the base.
1 The phone rings. The
the base flashes.
status
LED on
2 Press .
13
3 Press to finish the call.
Handset ringer tone
ringer
ringer
off on
•
ª
RINGER
OFF–ON
volume
Adjusting the ringer and ear speaker volume
ringer
•
ª
volume
•
volume
ª
In the standby mode, press .
Each time is pressed, the ringer tone setting changes and
the selected ringer tone sounds for 2 seconds.
Handset ringer switch
This switch turns the handset
ringer on or off.
ringer
off on
Handset ear speaker volume
The phone has four ear speaker volume levels, Normal, Medium,
High, and Loud. Pressing or during a telephone call will
change the ear speaker volume of the handset. This setting will
remain in effect after the telephone call has ended.
When you press in Loud mode or press in Normal
mode, error sound beeps.
Base ringer switch
This switch turns the base
ringer on or off.
Base speaker volume
To control the speaker volume of the
base, adjust the and
button as desired.
14
From the handset
redial/p
Redialing a call
talk
redial
talk
speaker
The last phone number entered can be quickly redialed.
If the recently dialed
number exceeds 32 digits,
only the first 32 digits are
retained for redialing.
From the base
1 Press . The
talk
LED blinks.
2 Press .
3 Press or place the handset on the
base to hang up.
blinks.
speaker
speaker
LED
1 Press . The
15
2 To call the last number dialed from the
base, press .
3 Press to finish the call.
You can cut off the sound from the base or the handset
mute
speaker
Mute
mute
mute
mute
talk
mute
microphone.
When speaking on the handset
1 Press during a telephone call.
The sound from the microphone is
cut off.
2 To cancel mute, press or
.
When speaking on the base
1 Press during a telephone call.
The sound from the microphone is
cut off.
2 To cancel mute, press , or
.
When the phone is ringing
Press when the phone is ringing. The ringer sound is cut
off. The ringer will sound when the next call is received.
16
mem
You must press a key
memory
Storing phone numbers
mem
memory
0
9
0
9
within 20 seconds or the
phone will return to
standby. If you return the
handset in the cradle the
phone will return to
standby too. Press mem
and you can go to
memory menu at any
time.
Your EXA 8955 stores up to 10 numbers in handset plus 10 numbers
in the base.
From the handeset
1 Press while in standby mode.
The
talk
LED flashes.
2
Dial the number you wish to store (up to
20 digits)
3
Press again.
4 Press - on the keypad to select
the memory location where you wish to
store the number.
5 The
From the base
talk
LED goes out and the
confirmation beep indicates the number
has been stored.
DIALING
17
MEMORY
1 Press .
2 Dial the number you wish to store.
3 Press .
Press - on the keypad to select
the memory location you wish to store
the number.
A confirmation beep indicates the
number is stored.
From the handset
speaker
memory
Making calls with memory dialing
talk
mem
talk
speaker
From the base
1 Press . The
talk
LED blinks.
2 Press .
3 Select the memory location
( - ) you wish to dial.
0 9
4 Press or return the handset to
the base to finish the call.
1 Press . The
blinks.
speaker
LED
2 Press .
3 Press the number keypad
9
0
( - ) to select the memory
location you wish to dial.
4 Press to finish the call.
18
From the handset
mem
memory
memory
Erasing a stored phone number
mem
1 Press in the standby mode.
2 Press again.
3 Enter the memory location number
From the base
1 Press .
2 Press again.
The
talk
LED flashes.
( - ) on the keypad you wish to
delete. A confirmation beep indicates
the number has been erased.
9
0
19
9
3 Press - on the keypad to select
0
the memory location you wish to store
the number.
A confirmation beep indicates the
number has been erased.
The Uniden EXA 8955 permits
speaker
talk
3-way conferencing
speaker
talk
3-way conversations between
the handset, base and outside
line.
Dialing from the 3-way
conversation mode is
possible only from the
handset.
When speaking on the handset
1 Press on the base to join
the 3-way conversation.
2
Press on the base to hang
up. The handset will still be
connected to the outline call.
When speaking on the base
1 Press on the handset to join
the 3-way canversation.
2
Press on the handset to hang
up.
CONFERENCE FEATURES
3-WAY
20
Intercom from the base to handset
page/int'com
int'c
talk
speaker
page/int'com
speaker
Using your EXA 8955 intercom
talk
int'c
talk
speaker
1 Press on the base.
The handset beeps.
2 Press or on the handset.
Speak into the mouthpiece to answer
the base.
3
To turn off the intercom, press on
the handset or on the base.
Intercom from the handset to base
1 Press on the handset.
The base beeps.
2 At the base, press or
. Speak into the base
microphone to answer the page.
21
3
To turn off the intercom, press on
the handset or on the base.
To transfer from the handset to the base
page/int'com
int'c
talk
speaker
speaker
page/int'com
speaker
int'c
talk
talk
Transferring a call
1 Press on the handset while
speaking on the handset. The line
will be placed on hold, and the
intercom tone will be sounded on
the base.
2 Press or on
the base. The intercom mode is
activated and you may speak to the
person at the base.
3 To complete the transfer to the base,
press on the handset.
To cancel the transfer, press
on the base.
To transfer from the base to the handset
1 Press on the base
while speaking on the speaker
phone. The line will be placed on
hold, and the intercom tone will be
sounded on the handset.
2 Press or on the
handset. The intercom mode is
activated and you may speak to the
person at the handset.
3 To complete the transfer to the
handset, press on the
base.
To cancel the transfer, press
on the handset.
22
The EXA8955 has a built-in answering system that answers and
The integrated answering device
Features
records incoming calls.
You can also use your answering system to record a conversation,
leave a voice memo message for others who use the phone, or to
announce a special message to callers when you're away from your
phone.
• Digital Tapeless Recording
• 15 minutes of Recording Time
• Selective Greetings (Outgoing Messages)
• Time and Day Stamp
• Remote Message Retrieval and Room Monitor
• Toll Saver
ANSWERING DEVICE
• Conversation Recording
Digital Tapeless Recording allows you to quickly review, save or
delete the messages. You'll never have to worry about a tape
wearing out, jamming, or resetting improperly.
The Integrated Answering System is easy and convenient to use, but
please read through all of the instructions carefully.
23
THE INTEGRATED
Setting up your answering system
ans on/off
clock
clock
clock
Press or
clock
ans on/off
clock
multiple times to scroll
through days, hours,
minutes, etc.
Turning the answering system on/of f
1 To turn the answering system on,
press . A beep tone will
sound and the current greeting
message is played.
2 To turn the answering system off,
press again.
Setting the clock
The clock on EXA8955 Answer System starts when power is
applied to the base. Follow these steps to set the clock to the
correct time.
1 Press and hold until a beep
tone sounds.
2 First, press or until the
correct day of the week is
announced. (Number zero through
six displays on the base as each day
is announced.) Press again
to select the day.
If you don't set the clock
within two minutes, the
system returns to standby.
4 Press or until you hear the correct time setting.
Numbers 1 through 59 display on the base as each minute is
announced. Press again to select the correct time.
5 The LED displays an A or P. Press or until you
hear the correct AM/PM setting.
6 Press again to end the time/day setting. The EXA8955
announces the time that you have set.
3 Next, press or until you
hear the correct hour setting.
Numbers 1 through 12 display on
the base as each hour is announced.
Press again to select the
correct time.
24
You can record a greeting
greeting
greeting
play
greeting
greeting
up to 30 second.
Setting your greeting
When you receive a call, the answering system automatically plays
either a preset message or your own greeting.
Preset Message
ª
The following message is prerecorded:
"Hello, no one is available to take your call. Please leave a message
after the tone."
ª
Recording your personal outgoing message (Greeting)
1 Press and hold until you hear
a long tone. Start recording your
message immediately after you hear the
long tone end.
2 When you are finished recording your
message, press or .
A long tone sounds and your message
plays back on the phone.
ª
Choosing between two outgoing messages.
1 Press to play the outgoing
message.
Stand within 12 inches in
front of the microphone
and speak clearly when
recording your outgoing
message.
25
2 Press again while the
message is played. This switches
between the two options.
Selecting the message record time
REC TIME
ANN/4/1
pin
pin
pin
You can set your answering system to record messages up to one
or four minutes long.
One minute option:
move the
switch to 1.
Four minutes option:
move the
switch to 4.
ª
Announce only feature:
The announce only feature plays an outgoing message, but it will
not allow the caller to leave a message. Move the
switch to the
The message counter LED displays “ ” when system is on
standby.
Prerecorded outgoing message for Announce only feature is:
"Hello, no one is available to take your call."
REC TIME
REC TIME
ANN
position.
REC TIME
Selecting a PIN code
To play your messages from a remote location, you will need to
enter a two-digit Personal Identification Number (PIN) code
(00-99). To select a PIN, perform the following steps.
Press or
multiple times to scroll
through numbers on the
display.
1 On the base, press and hold
button until a beep sounds and the
LED displays 00.
2 To set the first number, press
or to scroll from 00 to 90.
When the desired number appears in
the display, press . This selects
the first number.
3 To set the second number, press
or to scroll from 0 to 9.
When the desired number appears in
the display, press . This selects
the second number and then the
entered number is announced.
26
Setting ring time switch
RING TIME
2/4/TS
The ring time /toll saver switch
allows you to set the number of
rings the caller hears before the
answering system plays your
outgoing message. You can set
the switch to answer after two
rings or after four rings.
In the
TS
(Toll Saver) position, the answering system picks up after
two rings if you have new messages, and after four rings if there are
none. This way, if you call long distance to check your messages,
you can hang up after third ring to avoid billing charges.
27
Using your answering system
play
play
To stop playing your
play
messages, press
again.
Playing your message
The base LED shows the number of total messages on the
display. If the display is blinking, then there are new messages
waiting for you. The EXA 8955 is designed to play your new
messages first. After you play your new messages you can then
play your old messages.
1 Press . The system announces
the number of new and old
messages, then the incoming
messages are played. The time and
day each message was received is
announced after the message is
played, and the message counter
LED displays the number of the
current message.
2 When all new messages have
played, a long tone is heard. The
message counter LED stops flashing
to indicate that all of the new
messages have been reviewed.
3 After you have reviewed all your
messages, you can play your old
messages again. Press and
follow the instructions above.
28
play
play
Pressing before
play
play
2.5 seconds (4.5 seconds
from remote) of the
message has played causes
the system to scan back
one message.
If you have several
messages, press
until you return to the
message you want to
replay.
Repeating a message
1 Press to review your message.
The number of stored messages is
announces.
2 After a message has played for a few
seconds, press to repeat the
message.
3 Press at any time to stop
reviewing messages and return to
standby. The message counter LED
shows the total number of messages still
on the system.
Skipping a message
1 Press to review your messages.
The number of messages is announced.
Each time is
pressed, the system scans
forward one message.
If you have several
messages, press and hold
message you want to play.
29
2 Press at anytime to skip to the
next message.
3 Press at any time to stop
reviewing your messages and return to
standby. The message counter LED
shows the total number of messages on
the system.
to find the
play
delete
When you press delete,
delete
voice memo
voice memo
play
Microphone
you are permanently
deleting the message.
Once deleted, the message
cannot be replayed.
Deleting a message
Deleting individual message
ª
1 Press to review your message.
2 If you decide to delete a message,
press anytime during the
message. The system beeps and
immediately goes to the next
message.
3 After you have played all of your
messages, a long tone sounds on the
base speaker.
ª
Deleting all messages
Press and hold after reviewing your messages. A tone
sounds when all messages are cleared.
Voice memo
The voice memo function allows the user to record a message
(up to 10 minutes) on the base.
The voice memo function
is completely independent
of the outgoing message.
It’s handy for leaving
others a quick message.
A voice memo message is
treated as a typical
recorded message and will
be added to the stored
messages.
1 Press and hold ,
until you hear a long beep. The
message counter LED blinks.
2 Speak into the microphone.
3 When you have finished, press
or to stop
recording. The system returns to
standby.
30
play
voice memo
voice memo
A recorded conversation is
treated as a typical
message and will be added
to the stored messages.
Recording a conversation
You can record up to 10 minutes of conversation while you are
making your call from the handset.
1 During the conversation from the
handset. Press and hold
on the base. The unit begins recording
and the LED blinks. A beep that can be
heard by both parties sounds every 15
seconds.
2 To stop the recording, press
or .
You cannot record a conversation while you are
speaking on the base.
31
Remote access away from home
You can operate your answering system from a remote location
using any touch-tone telephone. Use this function to check for
recorded messages, to play or delete messages, even to record a
new outgoing message, and to monitor sounds in the room.
1 Call your telephone number.
You must enter a
command within 15
seconds of entering
command waiting mode
or the answering system
automatically hangs up
and returns to standby.
The system will only
playback messages for
four minutes and then it
returns to command
waiting mode. To continue
playing your message,
press #then 2again
within 15 seconds
2 During the answering machine is activated, press
PIN code.
#
and your
3 The answering system announces the time and day stamp
and the number of messages stored in memory. Then the
message playback automatically begins.
4 You may continue to listen to your massage, or you may
select a command from the following chart.
Command Function
#
then
1
Repeat
#
then
2
Playing your messages
#
then
3
Skipping a message
#
then
4
Deleting a message
#
then
5
Stop message playback
#
then
6
Answering system on
#
then
7
Voice memo record/stop
#
then
8
Outgoing message record/stop
#
then
9
Answer system off
#
then Room monitor
*
5 After all of your messages have played, or the playback time
exceeds 4 minutes, you will hear that the intermittent beeps
indicating that the system is in the command waiting mode.
You may enter another command at this time from the chart
above.
6 When you are finished, hang up to exit the system.
The answering system automatically returns to standby.
32
Remote room monitor
You can call your answering system from any touch-tone phone and
monitor sounds in the room where your base is installed.
1 Call your telephone number.
2 While the answering machine is activated, press
code.
#
and your PIN
3 The answering system begins announcing the time and day.
4 Press
5 Press
6 Press
#
then 5 to stop the messages.
#
then . You hear sounds in the room where your
phone is installed. After 15 seconds, the answering system
returns to the command waiting mode.
select another remote function. Or hang up to exit the system.
The answering system automatically returns to standby.
*
#
then to monitor the room for another 15 seconds. Or
*
33
page/int'com
Changing the digital security code
page/int'com
If the handset battery pack
is completely discharged
or the battery pack
removed, the digital
security code will be lost.
If this happens, a new
security code is set
automatically the next
time the battery pack is
charged.
The digital security code is an identification code used to connect
the handset and the base unit. Normally, setting the code is not
necessary.
The first time you charge your handset, the security code is
automatically set. (See page 3.)
In the rare situation that you suspect another cordless telephone
is using the same security code, you can change the code.
1 Remove the handset from the base
unit. Press .
2 While the handset is producing the
paging sound, hold
while placing the handset in the base
unit. The paging tone stops.
Leave the handset on the base
longer than 3 seconds. A new
random security code is set.
INFORMATION
ADDITIONAL
34
To attach the beltclip
headset
jack
Installing the beltclip
Headset installation
To remove the beltclip
Insert the beltclip into the holes
on each side of the handset.
Press down until it clicks.
Pull both sides of the beltclip to
release the tabs from the holes.
Your phone may be used with
an optional headset. To use
this feature, simply plug any
standard 2.5mm headset plug
into the headset jack. Your
phone is ready for hands-free
conversation.
35
Battery replacement
Note on power sources
Maintenance
and handling
When the operating time
becomes short, even after a
battery is recharged, please
replace the battery.
With normal usage, your
battery should last about one
year.
Please contact your place of
purchase for a replacement
battery.
Power Failure
During the period that the
power is off, you will not
be able to make or receive
calls with the telephone.
RECYCLING NICKELCADMIUM BATTERIES
NICKELCADMIUM
BATTERIES
MUST BE
Ni-Cd
Nickel-cadmium cells are used
in the battery pack. Please
take your used nickelcadmium battery packs to a
store that recycles nickelcadmium batteries.
DISPOSED OF
PROPERLY.
Caution
• Use the specified battery pack.
• Do not remove the battery from the handset to charge it.
• Never throw the battery into a fire, disassemble it, or heat it.
• Do not remove or damage the battery casing.
When slightly dirty
Wipe with a soft, dry cloth.
When very dirty
Wipe with a soft cloth that has
been dampened with diluted,
neutral detergent. Dry with a
dry cloth.
When the charging
terminals become dirty
Wipe with a pencil eraser or
other contact cleaner.
Caution
Do not use paint thinner,
benzene, alcohol, or other
chemical products. Doing
so may discolor the surface
of the telephone and
damage the finish.
36
If your phone is not performing to your expectations, please try
chan
talk
Troubleshooting
these simple steps first.
Symptom
The status light won't
come on when the
handset is placed in
the base unit.
YOUR NEW PHONE
The audio sounds
weak and/or scratchy.
Can't make or receive
calls.
The handset doesn't
ring or receive a page.
Suggestion
• Make sure the AC adapter is plugged
into the base unit and wall outlet.
• Make sure the handset is properly
seated in the base unit.
• Make sure the charging contacts on the
handset and base unit are clean.
• Make sure that the base unit antenna is
in a vertical position.
• Move the handset and or base unit to a
different location away from metal
objects or appliances and try again.
• Press to help eliminate
background noise.
• Make sure that you are not too far from
the base.
• Check both ends of the base unit
telephone line cord.
• Make sure the AC adapter is plugged
into the base unit and wall outlet.
• Disconnect the AC adapter for a few
minutes, then reconnect it.
• Reset the digital security code
(See page 34).
• Make sure is pressed.
• The battery pack may be weak. Charge
the battery on the base unit for 12-15
hours.
• The handset may be too far away from
the base unit.
• Place the base unit away from
appliances or metal objects.
• Reset the digital security code
(See page 34).
TROUBLESHOOTING
37
Symptom
The answering system
does not work.
Messages are
incomplete.
After a power failure,
the outgoing message
is deleted.
No sounds on the base
unit speaker during call
monitoring or message
playback.
Cannot access remote
call-in features from
another touch-tone
phone.
Suggestion
• Make sure the base unit is plugged
in.
• Make sure that the answering system
is turned on.
• The incoming messages may be too
long. Remind callers to leave a
brief message.
• The memory may be full. Delete
some or all of the saved messages.
• Record your greeting again.
The default messages should remain.
• Adjust the speaker volume on the
base unit.
• Make sure you are using the correct
PIN number.
• Make sure that the touch-tone phone
you're using can transmit the tone
for at least two seconds. If it
cannnot, you may have to use
another phone to access your
message.
38
General
Specifications
The EXA 8955 complies with FCC Parts 15 and 68.
Frequency control: PLL
Modulation: Frequency shift keying
Operating temperature: 0
°C to +50°C (+32°F to +122°F)
Base unit
RX frequency:
TX frequency:
Power requirements: 9V 350mA (from AC adapter)
Size:
Weight: Approx. 21 oz. (Approx. 594 g)
902.119 MHz to 905.016 MHz (30 channel)
924.997 MHz to 927.894 MHz (30 channel)
8-49/64 in. (W) x 6-57/64 in. (D) x 2-37/64 in. (H)
(222.5 mm (W) x 175 mm (D) x 65.3 mm (H))
Handset
RX frequency:
TX frequency:
Power requirements:
YOUR NEW PHONE
Size (without antenna):
Weight:
Battery: BT905
Specifications, features, and availability of optional
accessories are all subject to change without prior notice.
924.997 MHz to 927.894 MHz (30 channel)
902.119 MHz to 905.016 MHz (30 channel)
Rechargeable Nickel-Cadmium battery pack
7 in. (W) x 2-17/64 in. (D) x 2 in. (H)
(178 mm (W) x 57.6 mm (D) x 51 mm (H))
Approx. 8.6 oz. (244 g) (including battery)
Capacity 600 mAH, 3.6V
Talk mode 7 hours TYP
Standby mode 7 days TYP
39
SPECIFICATIONS
At Uniden, we’ll take care of you!
If you need any assistance with this product, please call our Customer Hotline at
1-800-297-1023
PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
Our Uniden representatives will be happy to help you with any
matters regarding the operation of this unit, available accessories,
or any other related matters.
Thank you for purchasing a Uniden product.
Hours: M-F 7:00 AM to 7:00 PM CST.
0 - 9
Index
3-way conferencing ..............20
A
Answering device
Features...........................23
Setting up........................24
Using...............................28
B
Base ringer switch ................14
Battery pack
Preparing and
charging ..........................10
Replacement and
handling..........................36
C
Channel.................................12
Connection..............................6
D
Dialing mode ..........................7
Digital security code........3, 34
E, F, G
Ear speaker volume .............14
H
Headset installation..............35
I, J, K, L
Intercom................................21
Installing the beltclip............35
M, N, O
Maintenance..........................36
Making a call ........................12
Memory dialing
Making a call
with memory dialing......18
Erasing a stored
phone number................19
Storing phone
numbers..........................17
Mounting the base unit
INDEX
to a wall ..................................8
Mute ......................................16
P, Q
Package contents....................4
R
Receiving a call ....................13
Redialing a call.....................15
Handset ringer tone .............14
Handset ringer switch..........14
S
Setting up your answering
system
Selecting a PIN code ......26
Selecting the
message record time......26
Setting the clock.............24
Setting ring time
switch..............................27
Setting your greeting......25
Tuerning the answering
systen on/off...................24
Setup
Base unit...........................5
Handset...........................10
Specifications........................39
T
Transferring a call.................22
Troubleshooting....................37
U, V, W, X, Y, Z
Using your answering system
Deleting a message........30
Playing your message ....28
Recording a
conversation ...................31
Remote access
away from home............32
Remote room monitor....33
Repeating a message......29
Skipping a message .......29
Voice memo ....................30
40
41
42
Loading...