Uniden ENR1504 User Manual

TABLE OF CONTENTS

WELCOME.................................................................................6

ENR1504 FEATURES...............................................................7

Internet Access Features ................................................7

LAN Features ..................................................................8

Router/Security Features ................................................8

Configuration & Management Features..........................8

Parental Control Features...............................................9

Advanced Router Features .............................................9

PACKAGE CONTENTS ..........................................................11

FRONT VIEW DETAILS..........................................................12

REAR VIEW DETAILS ............................................................13

QUICK INSTALLATION PROCESS .......................................14

STEP 1: HARDWARE INSTALLATION..........................................14

Installing the Hardware..................................................15

STEP 2: PC CONFIGURATION..................................................16

For Windows 95, 98, and ME........................................17

For Windows 2000 ........................................................18

For Windows NT 4.0......................................................19

For Windows XP............................................................20

STEP 3: BASIC ROUTER CONFIGURATION.................................21

Logging In......................................................................22

Changing the Default Password....................................24

Configuring the Time.....................................................25

Setting Parental Controls ..............................................27

Configuring Basic ISP Connections..............................35

ADVANCED ROUTER CONFIGURATION.............................38

CONFIGURING FOR A STATIC IP ADDRESS................................39

CONFIGURING FOR PPPOE SUPPORT......................................41

ENABLING MAC ADDRESS SPOOFING......................................43

CONFIGURING A FIXED IP ADDRESS FOR A PC.........................45

2

CONFIGURING A PC AS A HOST (PORT MAPPING).....................50

CONFIGURING UNIVERSAL PLUG AND PLAY (UPNP) .................55

CONFIGURING A DMZ.............................................................56

CHANGING THE DHCP CONFIGURATION..................................57

ENABLING DYNAMIC DNS........................................................63

EDITING THE ROUTING TABLE..................................................65

CONFIGURING PACKET FILTERING ...........................................68

ROUTER MAINTENANCE FEATURES..................................74

SYSTEM INFORMATION SCREEN...............................................74

REBOOTING THE ROUTER........................................................77

RESETTING THE ROUTER TO FACTORY DEFAULTS....................78

SYSTEM LOGS ........................................................................79

UPDATING THE FIRMWARE.......................................................83

TROUBLESHOOTING.............................................................84

POWER LED DOES NOT TURN ON ..........................................84

TEST LED STAYS ON .............................................................84

TEST LED DOES NOT COME ON..............................................84

A SINGLE PC CANNOT CONNECT TO THE ROUTER OR THE

INTERNET...............................................................................85

NO PCS CAN CONNECT TO THE INTERNET...............................86

SPECIFICATIONS...................................................................88

LEGAL NOTICE ......................................................................89

IC NOTICE:.............................................................................89

FCC INFORMATION.................................................................89

PRECAUTIONS!......................................................................91

IMPORTANT SAFETY INSTRUCTION...........................................91

Important Electrical Considerations ..............................92

ONE YEAR LIMITED WARRANTY.........................................94

WARRANTOR: UNIDEN AMERICA CORPORATION

(“Uniden”)......................................................................94

GLOSSARY.............................................................................96

MEMO....................................................................................109

TABLE OF FIGURES

Figure 1 Enter Network Password Screen.............................23

Figure 2 System Information Screen.....................................24

Figure 3 Account Configuration Screen.................................25

Figure 4 Time Information Setup Screen...............................26

Figure 5 Parental Controls Screen ........................................27

Figure 6 Network Access Rules Screen................................28

Figure 7 PC Access Rules Screen ........................................29

Figure 8 Add User Rules Screen...........................................30

Figure 9 Restrict Rules Screen..............................................32

Figure 10 Override Password Settings Screen......................34

Figure 11 WAN Configuration, Dynamic IP Screen...............36

Figure 12 WAN Configuration, Static IP Screen....................40

Figure 13 WAN Configuration, PPPoE Screen......................42

Figure 14 MAC Spoofing Screen...........................................44

Figure 15 DHCP Server Screen.............................................46

Figure 16 DHCP, Fixed IP Table Screen...............................47

Figure 17 DHCP, Add Fixed IP Screen .................................47

Figure 18 DHCP, Excluded IP Table Screen.........................49

Figure 19 DHCP, Add Excluded IP Screen ...........................49

Figure 20 Port Mapping Screen.............................................52

Figure 21 Port Mapping, Add Screen ....................................53

Figure 22 UPnP Setup Screen ..............................................55

Figure 23 DMZ Screen...........................................................57

Figure 24 DHCP Server Screen.............................................59

Figure 25 DHCP Server Screen.............................................61

Figure 26 LAN Configuration Screen.....................................62

Figure 27 Dynamic DNS Screen............................................64

Figure 28 Routing Table Screen............................................66

Figure 29 Routing Table, Add Screen ...................................67

Figure 30 Packet Filtering Screen .........................................69

3

4

Figure 31 Packet Filtering, Add Screen.................................70

Figure 32 System Information Screen...................................74

Figure 33 Reboot the Device Screen.....................................77

Figure 34 Reset to Factory Defaults Screen..........................78

Figure 35 Email Logs Screen.................................................80

Figure 36 Logs Screen...........................................................82

Figure 37 Firmware Update Screen.......................................83

TABLE OF TABLES

Table 1 LED Indicators ..........................................................12

Table 2 Commonly Used Well-Known Ports (TCP)...............51

Welcome

Congratulations on your purchase of the
ENR1504 10/100 Fast Ethernet Cable/DSL Router. This
Router is designed and engineered to exacting standards for
reliability, long life and outstanding performance.

With the ENR1504, you can share secure high-speed Internet
access to multiple computers through a single DSL or Cable
modem.

The firewall built into the ENR1504 is ready to provide secure
Internet access to all computers, directly out of the box, (for
Cable/DSL users who receive their WAN IP Address
automatically from their Internet Service Provider or ISP). Just
follow the hardware installation process and you are ready to
surf the web, protected from hackers.

5

For those wanting to activate other features provided in the
ENR1504, setup is easy. Follow the instructions and your
system will be up and running quickly.

This Owner’s Manual will guide you through the hardware
installation and network configuration process.

6

ENR1504 Features

The Uniden ENR1504 10/100 Ethernet Cable/DSL Router
provides many easy-to-use advanced features, described
below.

INTERNET ACCESS FEATURES

• DSL & Cable Modem Compatible: Allows you to
connect to either DSL or Cable modems with Ethernet
supported.

• Share High-Speed Internet Access: Your ISP gives
you a single WAN IP Address that can be shared among
all computers connected to the LAN. This is known as
a Private Network. The computers connected to the
router (LAN) are hidden from the Internet. This process
is called Network Address Translation or NAT.

• PPPoE Support: The ENR1504 supports Point-to-
Point Protocol over Ethernet or PPPoE. If you use a
cable modem or DSL to connect to the Internet, you may
need this feature enabled.

• Keep-Alive: When you use a PPPoE account, your ISP
may disconnect your PC if it remains inactive for a long
period of time. The keep-alive feature sends a data
packet over the connection at a designated time interval
to make sure the Internet connection remains active.

• Dial-on-Demand: For PPPoE accounts, this feature
activates the Internet connection during the boot-up
stage, or only when using the applications which require
Internet access, such as Internet Explorer.

• Static or Dynamic IP Address: Supports both Static
and Dynamic IP Addresses provided by your ISP.

LAN FEATURES

• Four 10/100 Ethernet Ports: 4-port dual-speed
(10/100 Mbps) fast Ethernet switch allows you to create
or extend your LAN.

• Auto MDI/MDI-X: Accepts both straight-through and
crossover networking cables, avoiding the confusion of
which type of cable is necessary.

ROUTER/SECURITY FEATURES

• DHCP Server: Dynamic Host Configuration Protocol
(DHCP) automatically issues LAN IP Addresses to PCs
and other Internet devices on your LAN.

• NAT Protection: Network Address Translation (NAT)
allows all LAN computers to share a single WAN IP
Address while hiding all LAN computers from external
sources.

• Stateful Packet Inspection: All Stateful Internet
Sessions (i.e. TCP) are monitored for malicious and
erroneous packets, protecting your network from
hackers.

• DoS Protection: Denial of Service (DoS) attacks
overload your router with invalid packets and connection
requests, using so many resources that your router
crashes and Internet access is no longer available.
The ENR1504 protects against DoS attacks.

CONFIGURATION & MANAGEMENT FEATURES

• Web-Based Configuration: No software installation is
required to configure the Router

7

8

• Remote Management: Any computer on the LAN can
connect and configure the ENR1504.

• Password Protected Configuration Utility: The
configuration utility is password protected, preventing
unauthorized users from modifying the feature settings.

PARENTAL CONTROL FEATURES

• Internet Access Control: Allows you to enable or
disable any computer on the LAN from accessing the
Internet; you can also determine when and how long
individual computers have access to the Internet.

• Key Word Filtering: Allows you to include or exclude
a list of key words specified for a web address (URL)
and/or that reside on the web site.

ADVANCED ROUTER FEATURES

• VPN Support: The router passes through Virtual
Private Networking (VPN) connections, so it can support
VPNs that use IPSec, L2TP and PPTP without any user
configuration.

• LAN Activity Log: Keeps track of all activity and
attacks on your network. This activity log can be sent to
you via e-mail hourly, daily, weekly or however you want
to review your LAN activity.

• DNS Server: Supports 2 Domain Name Service (DNS)
Servers to relay DNS entries. This speeds up Internet
connections.

• Online Conferencing Support: Supports Internet
Telephony and Conferencing programs.

• DMZ: Allows the Internet unrestricted access to one
computer within your LAN. This allows you to run
programs that are incompatible with firewalls.

• Port Mapping: Allows Internet users to access
Internet servers on your LAN. This allows you to
support a web server or other host from within the
firewall.

9

10

Package Contents

The following items are included with the ENR1504:

• One ENR1504 unit with stand.

• One 7.5V DC power adapter.

• One Easy-Start Installation Guide.

• Owner’s Manual on CD-ROM.

• One Cat-5 cable with RJ-45 connectors.

If any of these items are missing or damaged, immediately
contact your place of purchase or Uniden Customer Service at:
[phone], Monday-Sunday, 24/7.

Front View Details

Table 1 LED Indicators

Label/LED
Indications

Wired LAN
Link/Activity

Ports 1 - 4

WAN
Link/Activity

Test Amber

Power ON

Activity Description

Green
Amber
Blinking

Green
Amber
Blinking

OFF

OFF

The port is connected at 100 Mb/s.
The port is connected at 10 Mb/s.
Data is being transmitted/received.

The port is connected at 100 Mb/s.
The port is connected at 10 Mb/s.
Data is being transmitted/received.

The router is undergoing a power-on
self-test (POST). If the light remains
on, the router failed the POST.

The router passed the POST.
Power is on

Power is off

11

12

Rear View Details

• Reset Button: Pressing this button once performs a soft
reboot, similar to turning the power on and off. However,
if you press and hold the button for approximately 10
seconds, the device will reset to the factory default
settings, erasing any configuration changes you have
made (including the password).

• Ports 1 through 4: These auto-sensing 10/100
Ethernet RJ-45 Jacks ports automatically detect the
speed of any attached Ethernet device and provide a the
correct Ethernet connection. All of these ports are
configured with auto MDI/MDI-X, so they support either
straight or crossover cables, (Cat 5 UTP). Each port
supports a maximum cable length of 100 meters over
category 5 twisted pair cable.

• WAN Port: RJ-45 Interface connects to either the DSL
or Cable modem.

• 7.5V Power Jack: Connects to the Uniden supplied
external power adapter to the power jack.

Quick Installation Process

There are three steps to install your 10/100 Ethernet Router and
create a your own Local Area Network (LAN).

1. Hardware Installation: Through this process you will
physically connect your computers to your router.

2. PC Configuration: For each computer, you will need to
make sure they have the same LAN IP Address (The LAN IP
Address is similar to an area code for making telephone calls.
In order for all the computers to talk to each other, they must
reside in the same area code).

3. Basic Router Configuration: Within this step you can set
your Parental Controls, Passwords, and other features of
your 10/100 Router.

STEP 1: HARDWARE INSTALLATION

NOTE: During the hardware installation process, please

make sure all computers and the router are turned
off until the installation process is complete.

Before installing the ENR1504 you will need the following:

13

• One external DSL or Cable modem with an Ethernet

Port.

• Network Cables with RJ-45 connectors (UTP CAT 5).

• TCP/IP network protocols installed on all PCs. (See

page 85 if you need assistance)

14

INSTALLING THE HARDWARE

4. Connect to the DSL/Cable Modem: Connect one end of
the supplied CAT 5 network cable to the DSL/Cable Modem.
Insert the other end into the ENR1504 port labeled WAN.

5. Connect to the PC’s: Using standard CAT 5 network
cables, connect any one of the four available LAN ports
(labeled 1 through 4) to your PC’s network card or Ethernet
connection (RJ-45 jack).

6. Power on the Router: Plug the power adapter into an AC
power outlet and connect the power supply to the power jack
on the rear of the ENR1504. The power LED should
immediately turn on.

NOTE: The ENR1504 has no “on” switch. It will power on as

soon as the power adapter is connected.

STEP 2: PC CONFIGURATION

In order for your computer to communicate with the ENR1504,
both devices must be on the same LAN, i.e. the first three parts
of their IP addresses must be the same:

The default IP address of the ENR1504 Router is 192.168.1.1.
As a result, your PC’s IP address must start with 192.168.1 as
well. Fill in the last digit with some number other than 1 to
distinguish your computer from the router.

To verify and/or change your PC’s IP address so it is on the
same network, please see the instructions specifically for your
Microsoft operating system: Windows 95, 98, ME, NT, 2000 or
XP.

7. Observe the Power-On Self Test: When the ENR1504
powers on, it conducts a series of hardware diagnostics
called Power-On-Self-Test (POST). While the POST is
running, watch the front panel of the router. The Test LED
should stay ON during the POST. If router passes the
POST, the Test LED will turn off. If the Test LED stays on,
then the router has failed the test.

The hardware installation is complete. Continue to Step 2: PC
Configuration on page 16.

15

NOTES:

- If you are using the default ENR1504 settings and
the default Windows “Obtain an IP address
automatically” (DHCP) settings, no changes are
required.

- By default, the 10/100 Router will act as a DHCP
Server, automatically providing an IP Address and
other related information to each PC on the LAN
when that PC boots up.

- If you receive a Static (Fixed) IP address from your
Cable/DSL provider, write it down along with your
DNS Server information when prompted through the
steps below. You will need to enter the Static IP
address later during the IP Sharing Section of the
Owner’s Manual.

16

FOR WINDOWS 95, 98, AND ME

1. Click on Start, Settings, Control Panel. Double click on
Network.

2. In “The following network components are installed”
box, select the TCP/IP associated with your network adapter.
(If you have only one network adapter installed, you will only
see one TCP/IP listed.) Highlight it and click the
Properties button.

3. In the “TCP/IP Properties” window, select the “IP Address”
tab. If the “Obtain an IP address automatically” is
checked, this computer is ready to communicate with the
ENR1504. If it is not, proceed to step 4.

4. If there is an IP address listed, WRITE DOWN this IP
address on the memo page of this manual (page 109).

5. Select the DNS configuration tab. If there is an IP address
listed on this tab, WRITE DOWN this IP address on the
memo page of this manual (page 109).

NOTE: After you’ve configured your PC to communicate

with the ENR1504, you might need to enter these IP
addresses into the router in order to share your
internet access through your Cable or DSL modem.

6. Select Obtain an IP address automatically.

7. Click the OK button in the “TCP/IP Properties” window, and
click OK in the “Network” window.

8. Restart the computer if asked.

Repeat for each PC on your network. When all of your PCs are
configured, continue to Step 3: Basic Router Configuration on
page 21.

FOR WINDOWS 2000

1. Click on Start, Settings, Control Panel. Double click on
Network and Dial-up Connections.

2. Right click on the Local Area Connection that is associated
with the network adapter you are using and select the
Properties option.

3. In the “Components checked are used by this
connection” box, highlight Internet Protocol (TCP/IP), and
click the “Properties” button. If the “Obtain an IP address
automatically” is checked, this computer is ready to
communicate with the ENR1504. If it is not, proceed to step

4.

4. If there are any IP addresses listed on this screen, WRITE
DOWN these IP addresses on the memo page of this
manual (page 109). There may be an IP address listed
under Use the Following IP Address and one under Use
the Following DNS Server Addresses. Be sure to make a
note of BOTH IP addresses.

NOTE: After you’ve configured your PC to communicate

with the ENR1504, you might need to enter these IP
addresses into the router in order to share your
Internet access through your Cable or DSL modem.

5. Select Obtain an IP address automatically.

6. Click the OK button in the Internet Protocol (TCP/IP)

Properties window, and click the OK button in the Local
Area Connection Properties window.

7. Restart the computer if asked.

Repeat for each PC on your network. When all of your PCs are
configured, continue to Step 3: Basic Router Configuration on
page 21.

17

18

FOR WINDOWS NT 4.0

1. Click on Start, Settings, Control Panel. Double click on
Network.

2. Select the Protocol tab, and double click on TCP/IP
Protocol.

3. When the window appears, select the correct adapter for
your network adapter. If the Obtain an IP address from a
DHCP Server is checked, this computer is ready to
communicate with the ENR1504. If it is not, proceed to step

4.

4. If there is an IP address listed, WRITE DOWN this IP
address on the memo page of this manual (page 109).

5. Select the DNS configuration tab. If there is an IP address
listed on this tab, WRITE DOWN this IP address on the
memo page of this manual (page 109).

NOTE: After you’ve configured your PC to communicate

with the ENR1504, you might need to enter these IP
addresses into the router in order to share your
Internet access through your Cable or DSL modem.

4. Select Obtain an IP address from a DHCP Server.

5. Click the OK button in the TCP/IP Properties window, and
click OK in the “Network” window.

6. Restart the computer if asked.

Repeat for each PC on your network. When all of your PCs are
configured, continue to Step 3: Basic Router Configuration on
page 21.

FOR WINDOWS XP

1. Click on Start, Settings. If your view is already Classic

View, proceed to step 2. Otherwise, switch your view to
Classic View by right clicking your mouse while the cursor is

over the Start button.

2. Double click on Network Connections.

3. Right click on the Local Area Connection that is associated
with the network adapter you are using, and select the
Properties option.

4. In the This connection uses the following items box,
highlight Internet Protocol (TCP/IP). Click the Properties
button. If the Obtain an IP address automatically is
checked, this computer is ready to communicate with the
ENR1504. If it is not, proceed to step 5.

5. If there is an IP address listed, WRITE DOWN this IP
address on the memo page of this manual (page 109).

6. Select the DNS configuration tab. If there is an IP address
listed on this tab, WRITE DOWN this IP address on the
memo page of this manual (page 109).

NOTE: After you’ve configured your PC to communicate

with the ENR1504, you might need to enter these IP
addresses into the router in order to share your
internet access through your Cable or DSL modem.

7. Select Obtain an IP address from a DHCP Server.

8. Click the OK button in the Internet Protocol (TCP/IP)

Properties window. Click the OK button in the Local Area
Connection Properties window.

9. Restart your computer if asked.

19

20

Repeat for each PC on your network. When all of your PCs are
configured, continue to Step 3: Basic Router Configuration
below.

STEP 3: BASIC ROUTER CONFIGURATION

The ENR1504 10/100 Router uses a browser-based
management/configuration interface. Although the router’s
default settings allow most users to connect with no further
configuration, you will need to set the password, time zone, and
any desired parental access control rules. In some cases, you
may have to change a few of the communications settings to
connect to your ISP.

Your router will require more advanced configuration if any of the
following conditions apply:

• Your ISP gives you a static IP address to use for your
computer.

• Your ISP requires PPPoE support.

• Your ISP requires you to have a specific MAC or

hardware address to connect to the network (MAC
address spoofing).

• You want to make sure a particular PC (e.g., a mail
server or a web host) always gets the same IP address
(fixed IP address function).

• You need to run an Internet server or a web host from
within the firewall (port mapping or DMZ functions).

• You want to use the Universal Plug and Play feature
(UPnP).

with your network (MAC address blocking function).

• You need to configure the router’s DHCP settings or
configure the router to operate within a LAN that has an
existing DHCP server.

• You want to route or block data based on information in
each individual data packet (packet filtering feature).

• You want to link your router to a dynamic DNS service.

If none of these conditions apply to you, then the basic
configuration should be all you need. Even if you do need
advanced configuration, you will need to perform the basic
configuration as the first steps of an advanced configuration.

LOGGING IN
Before starting, be sure your computer is correctly configured to

obtain an IP address automatically in the TCP/IP networking
setup. If you have any trouble communicating with the
ENR1504, see Step 2: PC Configuration on page 16.

1. Open a web browser window, Internet Explorer or Netscape.

2. In the location field at the top of the browser window (where
you normally type the web page address), type the following
text exactly as shown:

http://192.168.1.1

3. Hit Enter. The router will display the Enter Network
Password window (see Figure 1).

NOTE: If the enter password window does not display,

double check the hardware setup in Step 1:
Hardware Installation on page 14 and Step 2: PC
Configuration on page 16.

• You want to block an external PC from communicating

21

22

Figure 1 Enter Network Password Screen

4. In the User Name field, enter the following (in upper case):

UNIDEN

5. Leave the Password field blank and click OK. The router will
display the System Information screen.

23

Figure 2 System Information Screen

6. On the System Information screen (Figure 2), note the
hardware version, software version, and boot code version
in the memo section of this manual (page 109) for future
reference.

CHANGING THE DEFAULT PASSWORD

1. In the menu on the left of the screen, click on System
Administration, then Account Configuration. This
displays the Account Configuration screen (see Figure 3).

24

Figure 3 Account Configuration Screen

2. Change the Administrative Login Name and
Administrative Password. Make a note of the login name
and password in the memo section of this manual (page

109).

3. Click Apply. If the router displays a dialogue box that says
“Values are saved. Do you really want to reboot the system
now?” click Cancel. We will reboot the router after all the
changes are made.

NOTE: The new name and password will take effect when

you reboot the router.

CONFIGURING THE TIME

1. In the menu on the left of the screen, click on System
Administration and then Time Information Setup. This
displays the Time Information Setup screen (Figure 4).

Figure 4 Time Information Setup Screen

2. In the Timezone field, select the time zone you are in.

3. If you want to enable the Network Time Protocol on the
router, select Enable in the NTP field. NTP is an Internet
protocol standard that will be used to synchronize Routers
clock to an internet based NTP server such as the U.S.
Naval Observatory Master Clocks in Washington, DC and
Colorado Springs CO.

4. If you enable NTP, enter the NTP Server URL, or select an
NTP server from the NTP Server List.

5. If you want your router to recognize Daylight Savings Time,
select Enable in the Daylight field.

6. Click Apply. If the router displays a dialogue box that says
“Values are saved. Do you really want to reboot the system
now?” click Cancel. We will reboot the router after all the
changes are made.

25

26

SETTING PARENTAL CONTROLS
Parental controls allow you to control Internet access for the

network as a whole or for each PC using its MAC address (a
hardware identification number assigned to an individual PC).

To access parental control features, in the menu on the left of the
screen, click on Firewall/Security and then Parental Controls.
This displays the Parental Controls screen (see Figure 5).

Figure 5 Parental Controls Screen

NETWORK-LEVEL CONTROL
If you want to set access control for the whole network, click

Network Access Rules. This displays the Network Access

Rules screen (see Figure 6).

NOTE: All settings on this screen apply to all computers

connected to the router.

27

Figure 6 Network Access Rules Screen

1. Select the level of Internet access you want to allow for the
network: full Internet access, no Internet access, or access
based on rules. If you click Use Access Control Rules,
configure the rules in the lower half of the screen.

2. If you want to restrict access based on certain keywords,
click Restrict Access Using Keywords. You will define
keywords on the Restrict Rules screen (see page 32).

3. If you want to allow a temporary password override for the
Internet restrictions, click Allow Password Overrides.
You will define keywords on the Set Override Password
screen (see page 33).

4. If you want to restrict access based on the time of day, click
Internet Access Curfew. Enter the time range during

28

which you want to Block or Allow Internet access. (Times
are in 24-hour format, so to block access from 10:00 pm to
6:00 am, select Block from 22:00 to 06:00.)

5. Click Apply. If the router displays a dialogue box that says
“Values are saved. Do you really want to reboot the system
now?” click Cancel. We will reboot the router after all the
changes are made.

PC-LEVEL CONTROL
The router can also set access control based on each PC’s MAC

address. The MAC address is a unique hardware address
assigned to each PC; MAC addresses are a six-part character
code separated by dashes or colons. If you want to set access
control for individual PCs by their MAC addresses, click PC
Access Rules. This displays the PC Access Rules screen (see
Figure 7).

allowed full Internet access (ALLOW ALL), no Internet access
(BLOCK ALL), or Internet access based on a rule (ALLOW
RULE). When you first open this screen, it will be blank except
for the Add, Modify, and Delete buttons at the bottom.

1. To add access control rules to a new PC, click the Add
button. This displays the Add User Rules screen (see
Figure 8).

Figure 7 PC Access Rules Screen

The PC Access Rules screen displays the MAC address of each
PC that has rules associated with it and whether the PC is

29

Figure 8 Add User Rules Screen

NOTE: PCs have full access by default. If you do not add

a PC to the User Rules list, that PC has full access.

2. Enter the MAC Address of the PC you want to create rules
for. Be sure to enter the six separate parts of the MAC
address into the six separate boxes in the field. (If you do
not know the MAC address of the PC, click on DCHP Server

30

at the left of the screen (see X-REF). The bottom of this
screen displays the MAC addresses of all computers
connected to the router.)

10. To change the rules configuration for a PC, select the PC’s
MAC address on the PC Access Rules screen (see Figure 7
on page 29) and click the Modify button.

3. Select the level of Internet access you want to allow for the
network: full Internet access, no Internet access, or access
based on rules. If you click Use Access Control Rules,
configure the rules in the lower half of the screen.

4. If you want to restrict the PC’s access based on certain
keywords, click Restrict Access Using Keywords. You
will define keywords on the Restrict Rules screen (see
page 32).

5. If you want to allow a temporary password override for the
Internet restrictions, click Allow Password Overrides.
You will define keywords on the Set Override Password
screen (see page 33). The override password applies to all
users.

6. If you want to restrict this PC’s access based on the time of
day, click Internet Access Curfew . Enter the time range
during which you want to Block or Allow Internet access.
(Times are in 24-hour format, so to block access from 10:00
pm to 6:00 am, select Block from 22:00 to 06:00.)

7. To restrict this PC to a certain amount of connection time,
under Total Connection Duration Time, click Limit To and
select the number of hours per day this PC is allowed to
access the Internet.

8. Click Apply. If the router displays a dialogue box that says
“Values are saved. Do you really want to reboot the system
now?” click Cancel. We will reboot the router after all the
changes are made.

9. Repeat the process with any other computers you wish to
restrict access for.

11. To delete all rules for a PC, select the PC’s MAC address on
the PC Access Rules screen (see Figure 7 on page 29) and
click the Delete button.

CONFIGURING RESTRICTION RULES
If you want to set access control for individual PCs by their

unique MAC address, click Restrict Rules. This displays the

Restrict Rules screen (see Figure 9).

Figure 9 Restrict Rules Screen

31

32

The Restrict Rules screen allows you to create a list of keywords
for restricting Internet access. You can list keywords to block or
to allow.

NOTE: The same keyword list applies any PCs configured

to use keyword-based restrictions.

1. Under Block/Allow the Keywords for URL Filtering,
select whether you want to create a list of keywords to Block
or to Allow. If you select Block, PCs restricted by this rule
will not be allowed to access sites that match keywords on
the list. If you select Allow, PCs restricted by this rule will
ONLY be allowed access to sites that match keywords on
the list.

2. Under Contain/Match the Keywords for URL Filtering,
select whether you want to restrict URLs that Contain the
listed keywords or exactly Match the listed keywords.

3. Enter the keywords under the Keyword field at the bottom of
the screen.

4. Click Add Keyword to add the keyword to the list.

5. If you want to delete a keyword, highlight the keyword on the
list and click Delete Keyword. If you want to delete all the
keywords from the list, click Clear List.

6. Click Apply. If the router displays a dialogue box that says
“Values are saved. Do you really want to reboot the system
now?” click Cancel. We will reboot the router after all the
changes are made.

CONFIGURING AN OVERRIDE PASSWORD
If you want to set a password to temporarily override Internet

access restrictions, click Set Override Password. This displays
the Override Password Settings screen (see Figure 9).

33

Figure 10 Override Password Settings Screen

1. To activate an override password, click Enable.

2. Enter the password under the Password field. Confirm the
password by entering it again in the Confirm Password
field.

NOTE: For security reasons, the password will not be

visible from this screen. Make a note of the
password in the memo page of this manual (page

109) or some other safe location.

3. If you want the password to expire after a certain number of
uses, click Limit Override Password Usage. Then, enter
the number of times the password will work before it expires.

4. In the Override Duration field, select the number of hours of
Internet access the override password will grant. After this

34