®
ANA 9610
900 MHz Analog
PBX
Cordless Telephone
Operating Guide
One Year Limited Warranty
WARRANTOR: UNIDEN AMERICA CORPORATION(“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the
original retail owner, this Uniden Product to be free from defects in
materials and craftsmanship with only the limitations or exclusions set
out below.
WARRANTY DURATION: This warranty to the original user shall
terminate and be of no further effect 12 months after the date of original
retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modified, altered, or used
as part of any conversion kits, subassemblies, or any configurations not
sold by Uniden, (C) improperly installed, (D) serviced or repaired by
someone other than an authorized Uniden service center for a defect or
malfunction covered by this warranty, (E) used in any conjunction with
equipment or parts or as part of any system not manufactured by
Uniden, or (F) installed or programmed by anyone other than as
detailed by the Operating Guide for this product.
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any time while this warranty is in effect,
warrantor will repair the defect and return it to you without charge for
parts, service, or any other cost (except shipping and handling) incurred
by warrantor or its representatives in connection with the performance
of this warranty. THE LIMITED WARRANTY SET FORTH ABOVE IS
THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE
PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER
WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion
or limitation of incidental or consequential damages so the above
limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state. This
warranty is void outside the United States of America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY:
If, after following the instructions in this Operating Guide you are certain
that the Product is defective, pack the Product carefully (preferably in its
original packaging). Include evidence of original purchase and a note
describing the defect that has caused you to return it, The Product
should be shipped freight prepaid by traceable means, or delivered, to
warrantor at:
Uniden America Corporation
BCS Division
4700 Amon Carter Blvd.
Fort Worth, TX 76155
817-252-3043, 8 a.m. to 5 p.m. Central,
Monday through Friday
Covered under one or more of the following U.S. patents:
®
4,511,761 4,523,058 4,595,795,
4,597,104
4,797,916 4,803,491 5,157,686
5,253,268
and other patents pending.
OMANA9610 ©1997 Uniden America Corporation. Printed in the USA.
All rights reserved.
PRECAUTIONS
Before you read anything else,
please observe the following:
WARNING!
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage to
the unit, DO NOT expose this unit to rain or moisture.
BATTERY WARNING
This equipment contains a Rechargeable Sealed
n
Lead-Acid Battery.
Do not short circuit the battery.
n
n
Do not charge the Rechargeable Sealed Lead-Acid
Battery used in this equipment in any charger other
than the one designed to charge this battery as
specified in this Guide . Using another charger may
damage the battery, or cause the battery to explode.
Handset Controls & Functions
1
2
14
3
4
5
6
7
8
1. Ringer ON/OFF switch
2. Message Display
3. Transfer (
4. Hold (
5. Redial (
6. Pause (
hold
redial
pause
xfer
) Key
) Key
) Key
) Key
7. Numeric Keypad
8. Microphone
bat low
5
8
0
lock
abc
jkl
tuv
oper
msg
chan
3
6
9
#
talk
talk
hold xfer conf flash
redial pause search memo
12
ghi
4
pqrs
7
9. Head Set Jack
10. Conference (
11. Flash (
12. Memo (
13. Search (
14. Talk (
15. Channel/Lock (
16. Volume (
vol
def
mno
wxyz
flash
memo
search
talk
9
15
16
10
11
12
13
) Key
vol
conf
) Key
) Key
chan
) Key
) Key
) Key
) Key
Base Unit Controls & Functions
hold
Key
status
Indicator
page/find
Key
Tone
Pulse
Tone/Pulse slide Switch
TABLE OF CONTENTS
Important Safety Instructions...............................................2
About Your ANA 9610 ..................................................4
Important Electrical Considerations .........................................5
Range ...............................................................5
Telephone Line Problems ................................................5
Radio Interference ......................................................6
More Than One Cordless Telephone .......................................6
Privacy...............................................................6
ANA 9610 Features ....................................................7
Installing Your ANA 9610 ...............................................8
Selecting the Installation Location..........................................8
Connecting the Telephone Line............................................8
Connecting the Telephone Cords ..........................................9
Tone/Pulse Switch.....................................................10
Applying Power to the Base and Charger Units ..............................10
Wall Installation .......................................................12
Attaching the Belt Clip to the Handset......................................17
Installing the Handset Battery Pack........................................18
Charging the Handset Battery Pack .......................................19
Charging Spare Battery Packs ...........................................20
Low Battery Indicator...................................................20
Cleaning the Battery and Charging Unit Contacts.............................21
Using Your ANA 9610 Handset .........................................22
ANA 9610 Handset Controls .............................................23
Using the Handset.....................................................24
Answering a Call ......................................................25
Making a Call.........................................................25
Feature Buttons .........................................................26
Placing a call “on hold” .................................................26
Transferring a Call.....................................................26
Connecting a Conference Call............................................26
Programming the Feature Buttons.........................................27
Function Keys ..........................................................28
Using Your ANA 9610 Memory ..........................................29
Storing a Number......................................................29
Erasing a Stored Number ...............................................30
Dialing with a Stored Number ............................................31
Memory Search .......................................................31
Chain Dialing .........................................................32
Using Your ANA 9610 Base Unit ........................................33
Using the Hold........................................................33
Using the Page/Find ...................................................33
Optional Head Set (EXP9530) ..............................................34
Optional Backup AC Adapter (EXP9505) .....................................35
Using an Optional Second 2500-type Analog Telephone .......................36
Connecting the Desk Telephone. .........................................36
Transferring a Call to the ANA 9610......................................36
Transferring a Call to the Desk Telephone ..................................36
Optional Accessories and Replacement Parts ................................38
Troubleshooting.........................................................39
Specifications...........................................................40
Uniden® is a registered trademark of Uniden America Corporation.
AutoStandby™ and AutoTalk™ are trademarks of Uniden America Corporation.
AutoStandby is a patented invention of Uniden America Corporation.
Important Safety Instructions
When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electrical
shock, and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a dry
cloth for cleaning.
4. Do not use this product near water; for example, near a sink
or in a wet area.
5. Do not place this product on an unstable cart, stand, or
table. The telephone may fall, causing serious damage to
the unit.
6. To protect the product from overheating, do not block or
cover any slots or openings in the base Unit. This product
should never be placed near or over a radiator or heat
register. This product should not be placed in a built-in
installation unless proper ventilation is provided.
7. This product should be operated only from the type of power
source indicated on the marking label.
8. Do not allow anything to rest on the power cord. Do not
locate this product where the cord will be damaged by
persons walking on it.
9. Do not overload wall outlets and extension cords, as this
can result in the risk of fire or electrical shock.
10. Never push objects of any kind into this product through the
Base Unit slots, as they may touch dangerous voltage points
or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this
product. Contact qualified service personnel when some
service or repair work is required. Opening or removing
covers may expose you to dangerous voltages or other risks.
Incorrect reassembly can cause electric shock when the
appliance is subsequently used.
12. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the
operating instructions. Adjust only those controls that are
covered by the operating instructions. Improper adjustment of
other controls may result in damage, and will often require
extensive work by a qualified technician to restore the
product to normal operation.
E. If the product has been dropped, or the cabinet has been
damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of
the leak.
CAUTION: To reduce the risk of fire or injury to persons by the
battery, read and follow these instructions:
1. Use only the appropriate type and size Battery Pack specified in
this Operating Guide.
2. Do not dispose of the Battery Pack in a fire. The cell may
explode.
3. Do not open or mutilate the Battery Pack. Released electrolyte
is corrosive and may cause damage to the eyes or skin. It may
be toxic if swallowed.
4. Exercise care in handling the battery in order not to short the
battery with conducting materials such as rings, bracelets, and
keys. The battery or conductor may overheat and cause burns.
5. Charge the Battery Pack provided with or identified for use with
this product only in accordance with the instructions and
limitations specified in the instruction manual provided for this
product.
6. Observe proper polarity orientation between the Battery Pack
and battery charger.
SAVE THESE INSTRUCTIONS
About Your ANA 9610
Congratulations on your purchase of the Uniden ANA 9610
Cordless Telephone. The ANA 9610 is designed and engineered to
exacting standards for reliability, long life, and outstanding
performance. It is designed to work with a PBX system. To get the
most from your ANA 9610, please read this Operating Guide
thoroughly. To help familiarize you with the features of your cordless
phone, refer to the Handset illustration foldout from the front cover, and
the Base Unit illustration foldout from the rear cover.
Your ANA 9610 includes the following items:
msg
lock
vol
batlow
talk
chan
talk
F4
mute
F3
hold
F2
conf
F1
xfer
def
3
abc
mno
6
12
jkl
5
wxyz
9
ghi
4
tuv
8
#
pqrs
7
oper
0
Base Unit
2 AC Adapters
Charging Stand
Handset Telephone Cord
2 Rechargeable
Batteries
Operating Guide
R
Operating Guide
OMANA 9610
Belt Clip
Wall Plate Adapter
If any of these items are missing or damaged, contact your PBX
Administrator. If your ANA 9610 is not performing to your
expectations, please try the simple steps listed in the Trouble
Shooting Section of this Guide. If you are still unable to resolve the
problem, contact your PBX Administrator.
Important Electrical Considerations
Warning:Please do not attempt to unplug any appliance
during an electrical storm.
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and
damage any device connected to it. This phone is no exception.
Caution: Changes or modifications to this product not
expressly approved by Uniden, or operation of this
product in any way other than as detailed by this
Operating Guide, could void your authority to operate
this product.
Range
Your new phone is designed to achieve the maximum possible range
by transmitting and receiving according to the highest specifications set
forth by the FCC and IC. We have rated this phone to operate at a
maximum distance with the qualification that the range depends upon
the environment in which the telephone is used. Many factors limit
range, and it would be impossible to include all the variables in our
rating. The Maximum Range rating of this phone is meant to be used
as a means of comparison against other range claims.
Telephone Line Problems
The FCC and IC have granted the telephone company the right to
disconnect service in the event that your phone causes problems on
the telephone line. Also, the telephone company may make changes in
facilities and services which may affect the operation of your unit.
However, your telephone company must give adequate notice in
writing prior to such actions to allow you time for making necessary
arrangements to continue uninterrupted service.
If you are having trouble with your telephone service, you must first
disconnect your phone to determine if it is the cause of your problem. If
you determine that it is the cause, you must leave it disconnected until
the trouble has been corrected.
Radio Interference
Radio interference may occasionally cause buzzing and humming
in your cordless Handset, or clicking noises in the Base Unit. This
interference is caused by external sources such as TV, refrigerator,
vacuum cleaner, fluorescent lighting, computer equipment, or
electrical storm. Your unit is NOT DEFECTIVE. If these noises
continue and are too distracting, please check around your office to
see what appliances may be causing the problem. In addition, we
recommend that the Base not be plugged into a circuit that also
powers a major appliance because of the potential for interference.
Be certain that the antenna on the unit is fully extended when
needed.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving
radio signals from another cordless telephone or other source of
interference. If you cannot eliminate this type of interference, you
need to change to a different channel.
Finally, it should be noted that some cordless telephones operate
at frequencies that may cause interference to nearby TVs and
VCRs. To minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top of a TV or
VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the
interference.
More Than One Cordless Telephone
If you want to use more than one cordless telephone in your office,
they must operate on different channels. Press the channel key to
select a channel that provides the clearest communication.
Privacy
Note: Cordless phones are radio devices. Communications
between the Handset and Base Unit of your cordless telephone are
accomplished by means of radio waves which are broadcast over
the open airways. Because of the inherent physical properties of
radio waves, your communications can be received by radio
receiving devices other than your own cordless telephone unit.
Consequently, any communications using your cordless telephone
may not be private.
ANA 9610 Features
Super Long Range 900MHz Digital
n
2-line, 16-digit LCD Display
n
Headset Jack
n
Ringer Volume Control
n
Handset Volume Control
n
Single button access to: CONFERENCE, HOLD, and
n
TRANSFER features
Four Function Keys: PAUSE, FLASH, REDIAL, SEARCH
n
20 Number Memory Store and Search
n
Separate Charging Stand with Spare Battery Charging
n
Capability
Second Spare Battery
n
AutoStandby
n
AutoTalk
n
Vibrator Ringer Alert
n
Easy Installation
n
Out of Range Protection
n
Low Battery Protection System
n
n
Key Pad Lock Feature
n
Wall Mountable separate Base Unit
n
Wall Mountable separate Charging Unit
Installing Your ANA 9610
Selecting the Installation Location
Select a location for the ANA 9610 to avoid excessive heat or
humidity. The Base Unit of your ANA 9610 can be placed on a
desk or tabletop near a standard 120V AC outlet and telephone line
jack. The Base Unit can also be mounted on a standard AT&T or
GTE wall plate using the optional Wall Mount Adapter. If you will
use the ANA 9610 with a Standard 2500 type Telephone Desk
Unit, place the ANA 9610 near that phone. Keep the Base Unit
and Handset away from sources of electrical noise (motors,
fluorescent lighting, computers).
Connecting the Telephone Line
There are two types of phone outlets:
1) Modular Jack
Plug the telephone line cord from the Base Unit into a standard
modular telephone jack. (Note: If you do not have a modular
jack, contact your local telephone company for information on
the installation of these jacks.)
2) Hard-wired Jack
A modular jack converter (not included) is required. You may
need to rewire when connecting the converter (making
color-coded connections).
Note: Your Uniden Telephone Dealer or a telephone supply store
can advise you on the proper adapter or converter.
Connecting the Telephone Cords
The ANA 9610 must be connected to an analog PBX port or a
standard analog telephone line.
CAUTION:
Never install telephone wiring during a lightning storm.
n
Never touch uninsulated telephone wires or terminals unless the
n
telephone line has been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
n
Line in
From
Telephone
Jack
You can also connect a standard 2500-type desk phone to the
ANA 9610:
Connect to the LINE OUT Jack
To Optional
2500-type
Telephone
Tone/Pulse Switch
Be sure the TONE/PULSE switch is in the TONE position.
Tone
Pulse
Note: Most systems are Tone dialing. Check with your PBX
Administrator if you are not sure whether your system is
Tone or Pulse dialing.
Applying Power to the Base and Charger Units
AC
Adapter
Line in
From
Telephone
Jack
Line out
to Standard
2500 type
Desk Phone
Use only the supplied AC Adapter: AD-9500
IMPORTANT! Route the power cord where it will not create a trip
hazard, or where it could become chafed and create a fire or other
electrical hazards.
Note: The AC Adapter furnished with this phone may be equipped
with a polarized line plug (a plug having one blade wider than
the other.) This plug will fit into the power outlet only one way.
If you are unable to insert the plug fully into the outlet, try
reversing the plug.
Do not alter the shape of the
blades of the polarized plug.
Note: If you cannot plug the AC Adapter into the outlet, contact
someone about replacing the outlet.
The unique design of your ANA 9610 allows you to place the
Handset in the Charging Unit with or without the Belt Clip attached.
The Charging Unit also has the ability to charge a second battery with
or without the Handset being charged. The Battery Packs can
automatically be recharged either in or out of the Handset.
AC
Adapter
Use only the supplied AC Adapter: AD-960
Wall Installation
Standard Wall Plate Mounting
These Phones are designed to be mounted on a standard AT&T or
GTE wall plate. To attach the wall mount stand to the Base Unit:
1. Slide the Wall Mount stand
into the notches at the top of
the Base Unit, rotate the Wall
Mount stand down and snap it
into place.
2. Plug the AC Adapter into the Base Unit as previously
described.
3. Place the AC Adapter cord
inside the molded channel of
the Wall Mount stand.
LINE
4. Plug one end of the short telephone cord into the
the Base Unit. Optionally, plug one end of a standard 2500
type desk phone into the
telephone cord(s) inside the molded channel(s) on the bottom
of the Wall Mount stand.
5. Plug the other end of the short telephone cord into the modular
wall jack.
PHONE
jack. Then place the
jack on
6. Place the Base Unit on the posts
of the wall plate and push down
until it’s firmly seated.
7. Plug the AC Adapter into a
standard 120V AC wall outlet.
Note: Do not use an outlet controlled by a wall switch.
Direct Wall Mounting
If you do not have a standard wall plate, you can mount your phone
directly on a wall. Before mounting your phone, consider the following:
n
Select a location away from electrical cables, pipes, or other
items behind the mounting location that could cause a hazard
when inserting screws into the wall.
n
Make sure the wall material is capable of supporting the weight
of the Base Unit.
n
Use #10 screws with anchoring devices suitable for the wall
material where the Base Unit will be placed.
1. Insert two mounting screws 3
15
inches apart. Allow about
16
3
16
of an inch between the wall
and screw heads for mounting
the phone.
2. Plug and secure the AC Adapter cord by following steps 2 and
3oftheStandard Wall Plate Mounting.
3. Plug one end of the telephone
line cord into the
LINE
jack on
the Base Unit. Optionally, plug
one end of a standard 2500
type desk phone into the
PHONE
jack. Then place the
telephone cord(s) inside the
molded channel(s) on the
bottom of the Wall Mount
stand.
4. Place the Base Unit on the
posts of the wall screws and
push down until it’s firmly
seated.
3/16 in.
3 15/16 in.
5. Plug the other end of the short
telephone cord into a telephone
wall jack.
6. Plug the AC Adapter into a standard 120V AC wall outlet by
following step 7 of the Standard Wall Plate Mounting.
Charging Unit Wall Mounting
The Charging Unit is also designed to be wall mounted. you can mount
your phone directly on a wall. Before mounting your charging unit,
consider the following:
Select a location away from electrical cables, pipes, or other
n
items behind the mounting location that could cause a hazard
when inserting screws into the wall.
n
Make sure the wall material is capable of supporting the weight
of the Charging Unit.
n
Use #10 screws with anchoring devices suitable for the wall
material where the Charging Unit will be placed.
1. Insert two mounting screws 1-1/2
3
inches apart. Allow about
16
of an
inch between the wall and screw
heads for mounting the phone.
2. Plug the AC Adapter into the
Charging Unit as previously
described. Wrap the AC Adapter
cord around the strain relief.
3/16"
Strain
Relief
1 1/2"
3. Place the Charging Unit on
the posts of the wall screws
and push down until it’s firmly
seated.
Strain
Relief
4. Plug the AC Adapter into a
standard 120V AC wall outlet.
3/16"
1 1/2"
AC
AC
Adapter
Adapter
Attaching the Belt Clip to the Handset
You can use the Belt Clip to attach the Handset to your belt or pocket
for convenient portability.
1. Snap the tab out of the Belt Clip
notch on the top of the Handset.
2. Slide the clip into the tab slot.
(CAUTION: The Belt Clip is
designed to fit snugly onto the
Handset.)
3. Press firmly until it snaps into
place.
4. To remove, simply press the
retain clip in toward the Belt
Clip blade and slide the clip up
at the same time. Once the
Belt Clip is removed
remember to re-install the
cover tab.
Installing the Handset Battery Pack
1. Remove the battery cover by
pressing the latch and sliding
the cover down and off of the
Handset.
2. Slide the Battery Pack down
into the Handset.
NOTCH
Note: You may have to remove the old battery at this time.
3. Place the cover and slide the
cover up until it latches into the
Handset.
Charging the Handset Battery Pack
The Rechargeable Sealed Lead-Acid Battery Pack must be fully
charged before using your ANA 9610 for the first time. (
Charge the Battery Pack without interruption for 5 hours.
1. Place the Handset in the front slot
of the Charging Unit.
2. Make sure the CHARGE 1
indicator lights. If the CHARGE 1
light doesn’t light, check to see
that the AC Adapter is plugged in,
and that the Handset is making
good contact with the Charging
Unit charging contacts.
Note:
)
Charging Spare Battery Packs
The Charger Unit of your ANA 9610 is equipped to charge the
Spare Battery Pack with or without the Handset in the front slot.
1. Slide the Spare Battery Pack
into the second slot in the
Charging Unit until the
retaining clip snaps over the
top of the pack.
2. Make sure the CHARGE 2
indicator lights. If the
CHARGE 2 indicator doesn’t
light, check to see that the AC
Adapter is plugged in, and that
the Battery Pack is making
good contact with the
Charging Unit charging
contacts.
Note: Charge the Battery Pack without interruption for 8 hours.
3. When charging is complete, press out on the latch and remove
the Battery Pack for use. Or, if you don’t need the Battery
pack immediately, leave it in the Charging Compartment; it will
not overcharge.
Low Battery Indicator
When the Battery Pack in the
Handset is low and needs to be
charged, you will see a message
on the display.
On a Call In Standby Mode
Only the
Handset beeps once every 3 seconds Handset beeps every 15 seconds for
Complete your call as quickly as
possible
Replace Battery pack within 20
seconds to continue call.
talk
button operates.
None of the buttons operate.
15 minutes.
Cannot make call.
Replace Battery Pack before making a
call.
Return the Handset to the Charging Unit for charging or replace the
Handset Battery Pack with another charged Battery Pack.
batt low
Cleaning the Battery and Charging Unit Contacts
To maintain a good charge, it is important to clean all charging
contacts on the Handset, Spare Battery Pack and Charging Unit about
once a month. Use a pencil eraser or other contact cleaner. Do not
use any liquids or solvents.
Using Your ANA 9610 Handset
Before using your ANA 9610, be sure to raise the antenna to the
vertical position.
Note: Operation of the ANA 9610 is performed using the Hand-
set out of the Charging Unit.
ANA 9610 Handset Controls
talk
Condition Action LCD Display
Handset Earpiece Volume
(During a Call)
Ringer Select (Standby
Mode)
Press
vol
the Handset to select a
high or low Earpiece
volume level.
Press
vol
the Handset to select on of
the following settings:
Ring type A (High)
Ring type A (Low)
Ring type B (High)
chan
on the front of
on the front of
vol
No display indications.
Ring Type A
Ring Type A
High
High
Ring Type A
Ring Type A
Low
Low
Ring Type B
Ring Type B
High
High
Ring type B (Low)
Ring Off (Vibrate)
Ring Type B
Ring Type B
Low
Low
Ring Off
Using the Handset
When you pick up the Handset
and press
talk
, you will see:
After the connection has been
made between the Handset and
Base, you will see:
Or, you may see one of the following:
Condition Indicator LCD Screen
No Connection to Base
Unit
Channel Busy Error Tone CHANNEL BUSY
Line in Use Error Tone LINE IN USE
Error Tone
AQUIRING
LI N K
talk
NO SERVICE
If the Handset is at the range limit
of the ANA 9610, or no power is
going to the Base Unit, you may
see:
Take the following action:
During a Call In Standby Mode
Condition
Action
Warning Tone Can’t make or answer calls
Move back in range within 20
seconds or check power to the
Base Unit.
NO SERVICE
(Phone may ring
intermittently)
Move back within range or
check power to the Base
Unit.
Answering a Call
When you receive a call, the Handset
rings and you’ll see:
Handset in the Charging Unit Handset out of Charging Unit
Pick up the Handset. The AutoTalk
feature allows you to answer the call
immediately.
When you finish the call, place the Handset back in the Charging Unit. AutoStandby
automatically hangs up the phone.
—OR–
talk
Press
to hang up the phone
Press
talk
INCOMING
CALL
Making a Call
Press
talk
. The
talk
Icon will
illuminate after the Handset/Base are
connected, and you’ll see:
talk
When you hear a dial tone, enter the
number you are calling. (You can also
dial from memory. See the section on
“Using Memory.”)
talk
5551212
When you finish the call, press the
the phone and put it in AutoStandby.
talk
button again, this will hang up
Feature Buttons
Note: The exact operation of the Feature Buttons depends on how
your PBX system is configured. Contact your PBX
Administrator for more information.
Placing a call “on hold”
Press
hold
. You’ll hear a “beep”
and see:
HOLD
talk
To resume the call, press
holdortalk
Transferring a Call
Press
xfer
(TRANSFER). You’ll
hear a “beep”, and see:
Dial the target number.
When the receiving party answers,
xfer
press
transfer.
to complete the
Connecting a Conference Call
To connect a second party to a
call in progress, press
(CONFERENCE). You’ll hear a
“beep,” and see:
Dial the second party’s number.
conf
.
3410
talk
CONFERENCE
talk
When the other party answers,
conf
press
conversation.
to have a three-way
3410
talk
Programming the Feature Buttons
The Transfer and Conference Keys can be programmed for special
use, such as causing a “Hook Flash” followed by a special number or
function.
xfer
For example — to program the
outside transfers only:
Press
Press
Press
Press
memo
flash
9
memo
.
.
.
.
key for “Hook Flash” and 9 for
PHONE NO.?
F
F9
LOCATION?
xfer
Press
.
STORING
Note: For the ANA 9610, conference and transfer keys are
operated by the Flash Hook function. Please, program you
system transfer or conference code with the assistance of the
PBX System Administrator.
Function Keys
HOLD
Press once, you’ll hear a “beep” and the call is placed on hold.
Press
holdortalk
XFER
Press
xfer
(Transfer), you’ll hear a “beep”.
Dial the target number.
When the receiving party answers, press
CONF
To connect a second party to a call in progress, press
(CONFERENCE). You’ll hear a “beep”.
Dial the second party’s number.
When the other party answers, press
conversation.
FLASH
Press once to cause a “Hook Flash” while on a call.
Press once to program a “Hook Flash” in a Feature Button.
to resume the call (local hold).
xfer
to complete call.
conf
to have a three-way
conf
REDIAL
To dial the last number called, press
will redial the last number called.
talk
, then
redial.
The phone
PAUSE
Press once to program a Pause while storing a number in Memory.
SEARCH
Press to begin Memory Search. (See the following Section for
Memory Search.)
MEMO
Press
memo
Press desired function.
Press memory location (1-20).
Press
memo
.
, then
xfer
.
Using Your ANA 9610 Memory
Use these buttons to operate the
ANA 9610 Memory
Storing a Number
1. Press
memo
beep, and see the message:
. You will hear a
hold xfer conf flash
redial pause search memo
PHONE NO.?
2. Enter the number (up to 16 digits)
you want to store.
PHONE NO.?
5551234
a.To program a Pause in the dialing
pause
sequence, press
3. Press
message:
memo
. You will see the
.
LOCATION?
LOCATION?
12
4. Enter the number (01) -(20) for the
memory location to store. You’ll
hear a confirmation beep and see
the message:
STORING
Note: After pressing memo the second time, you have 20 seconds
to enter the memory location. Otherwise, an error tone
sounds and the unit returns to Standby.
5. The ANA 9610 then returns to Standby mode.
Example: Store 555-1234 in memory location 12:
a.Press
memo
.
PHONE NO.?
b. Enter
c. Press
d. Press
5551234
memo
12
The Handset beeps. This is
confirmation that you have
programmed 5551234 into
memory location 12 and
you see:
The phone then returns to Standby.
.
.
.
Erasing a Stored Number
1. Press
2. Press
memo
memo
.
.
PHONE NO.?
5551234
LOCATION?
LOCATION?
12
PHONE NO.?
DELETE NO.?
01
3. Enter the memory location
number (01) to (20) you want
to clear. You will hear a long
beep and see:
DELETING
Dialing with a Stored Number
Note: The following applies when the phone is in Standby Mode, and
you have already established a connection between Handset
and Base Unit.
1. Press
2. Press
talk
.
memo
.
02
talk
3. Enter the Memory Location
(01 - 20).
8159620
talk
The phone automatically dials the number shown.
Memory Search
You can search all 20 Memory Locations to find the number you need.
Once you have found the number, you can automatically dial that
talk
number by pressing the
1. Press
(If Memory Location 01 doesn’t have a
stored number, search will display the
first stored number.)
search
automatically starts at memory
Location 01.
. Search
key.
MEMORY SEARCH
MEMORY NO.01>
8159620
vol
3. a.Press
next used Programed Memory
Location.
b.You can also press
to a previous used Memory
Location.
again to move to the
chan
to move
MEMORY NO.03>
8159632
c. Pressing the
will move down through the
Memory (20 to 1). Pressing
vol
you will move up through
the Memory (1 to 20). Press
volorchan
desired Memory Location.
4. Once you have the desired
number, press
talk
The
The phone will then
automatically dial the number.
chan
key, you
until you reach the
talk
.
icon appears.
MEMORY NO.20>
9876543210
9876543210
talk
Chain Dialing
You can dial any stored number while you are on a call. This is
sometimes needed for Long Distance Access Codes or Account
Access Numbers.
1. While you are on the call,
search
press
2. Press
3. Once you have the desired
volorchan
to locate the number in
Memory.
number, press
dials the number.
.
talk
as needed
. The phone
MEMORY SEARCH
MEMORY NO.20>
9876543210
9876543210
talk
Using Your ANA 9610 Base Unit
Although most of the ANA 9610 operations are performed at the
Handset, there are two operations performed at the Base Unit.
The
call.
status
LED (2) blinks whenever the Handset is connected to a
1
3
2
Using the Hold
The
hold
button (1) is used in conjunction with a desk top phone to
switch from the Handset to a desk top phone.
1. If you need to use a desk top phone which the ANA 9610 is
connected to, press
top phone.
2. To resume using the Handset, press
press
talk
on the Handset. The Handset resumes functioning as
before.
hold
on the Base unit then pick up the desk
hold
on the Base unit, then
Using the Page/Find
The
page/find
page/find
Note: The Handset Ringer must be on and set to Type A or B in
button (3) is used to locate the Handset. Pressing
will send a ring signal to the Handset.
order for the page/find function to work.
Optional Head Set (EXP9530)
The optional Head Set provides a “Hands-Free” Option for the
ANA 9610. With the Head Set installed, you can use the Belt
Clip to carry the Handset, and conduct a conversation using the
Head Set.
To install the optional Head Set,
open the cover over the
HEADSET Jack and plug the
Head Set in.
No other settings are needed.
Operation of the ANA 9610 using the Head Set is exactly the
same as using the Handset. However, you will hear through the
Head Set earphone, and talk through the Head Set microphone.
The Handset earphone and microphone (mouthpiece) are
disconnected.
Optional Backup AC Adapter (EXP9505)
The Optional Backup AC Adapter provides protection against losing a
call in case of AC Power failure. The Backup Adapter contains a
Battery Pack that provides enough power for you to complete the call
and hang up.
To install the Backup Adapter:
1. Disconnect the Standard AC Adapter from the Base Unit of the
ANA 9610.
2. Plug the AC Adapter into the jack of the EXP9505.
3. Plug the wire from the EXP9505 into the DC IN jack of the
Base Unit.
To Base Unit
From AC
Adapter
Backup
AC Adapter
Using an Optional Second 2500-type
Analog Telephone
Analog Telephone.
A standard 2500-type Desk telephone can be used with the
ANA 9610. Calls can then be answered with the Desk phone
and transferred to the ANA 9610.
Note:A special Security Feature disconnects the Desk phone
whenever the ANA 9610 Handset is in use.
Connecting the Desk Telephone.
Connect a telephone cord from the Desk phone to the LINE OUT
jack on the ANA 9610 Base Unit.
LINE OUT
The Desk phone can now be used to answer or place calls in the
normal manner.
Transferring a Call to the ANA 9610.
1. Press
The call is now transferred to the ANA 9610, and the Desk
phone is disconnected.
hold
on the Base unit,
hang up the desk phone and
talk
press
on the Handset.
talk
chan
vol
Transferring a Call to the Desk Telephone
1. Press
2. Pick up the the Desk phone and press
The ANA 9610 Handset disconnects.
hold
on the ANA 9610 Base Unit.
talk
on the Handset.
Typical Applications
You can use the ANA 9610 together with a standard PBX telephone
to give you effective business communications both at your desk and
away from it. Contact your PBX Administrator for more information
about your System.
You can have your PBX system programmed so the following
sequence occurs:
1. Your PBX telephone rings first.
2. If you don’t answer the PBX telephone after a set number of
rings, the call is automatically transferred to the ANA 9610.
3. If you don’t answer the call after a set number of rings, it is
automatically transferred to your Voice Mail.
Note: It is good practice to keep the number of rings in each case to 2
or 3. This gives you a chance to answer the call, and doesn’t
keep the other party waiting too long.
Optional Accessories and Replacement
Parts
For the following Optional Accessories and Replacement Parts
contact your PBX Administrator.
AC Adapter Telephone Cord
Backup AC Adapter
EXP9505
Base Unit Wall Mount
EXP9660
500 mAh Battery
BT-9000
Head Set
EXP9530
Belt Clip
EXP9602
Operating Guide
R
Operating Guide
OMANA 9610
Charger and AC
Adapter EXP9685
Leather Case
EXP9683
Troubleshooting
If your ANA 9610 Cordless Telephone is not performing to your
expectations, please try these simple steps. If you are still unable to
resolve the problems, contact your PBX Administrator.
Note: Do not attempt to service this unit yourself. All service must be
done by qualified service personnel.
Problem Suggestion
Make sure the AC Adapter is plugged into
Charge light won’t come
on when Handset is
placed in Charging Unit.
Conversation
interrupted frequently.
Warning tone and NO
SERVICE message.
Handset doesn’t ring.
•
the Base Unit and wall outlet.
Make sure Handset is properly seated in
•
Charging Unit.
Make sure the Sealed Lead-Acid Battery
•
Pack is properly placed on the Handset.
Make sure that the charging contacts on
•
the Handset and Charging Unit are clean.
Make sure that the Base Unit antenna is
•
fully vertical.
• Move closer to the Base Unit.
• Check for LOW BAT warning.
• Move closer to the Base Unit.
• Sealed Lead-Acid Battery may be weak.
Charge the Battery Pack for 5-6 hours.
•
Make sure the Base Unit antenna is fully
vertical.
•
The Handset may be too far away from
the Base Unit.
•
Ensure the Ringer ON/OFF switch is in
the ON Position.
Specifications
General: The ANA 9610 complies with FCC and IC parts 15 and
68.
Frequency Control : Phase Lock Loop
Modulation : FM
Operating Temperature : −10° to 50° C
Base Unit
Receive/Transmit Frequency: 902 MHz to 928 MHz
Power Requirements : 10V DC from supplied AC Adapter
Size : 4 1/4 in.Wx71/2in.Dx21/4in.H
Weight : Approx. 15.4 oz.
Handset
Receive/Transmit Frequency: 902 MHz to 928 MHz
Power Requirements : Rechargeable Sealed Lead Acid
Battery Pack
Size : 2 1/4 in.Wx11/2in.Dx81/2in.
H
with antenna
Weight : Approx. 8.8 oz. with battery
Battery : Capacity 500 mAH, 4.0V
Talk Mode : 5 hours (typical)
Standby Mode : 40 hours (typical)
Specifications shown are typical and subject to change without
notice.
Loading...