U-Line U-2175BEVCS-02 Installation Manual

®

INSTALLATION GUIDE

2000 SERIES

GLASS DOOR

REFRIGERATORS

U-2175RCGOL-00

U-2175RCGS-00

U-2175RCGS-01

BEVERAGE

CENTERS

REFRIGERATORS

U-2175RFB-00

U-2175RFS-00

U-2175RFS-01

U-2175RFW-00

REFRIGERATOR/

FREEZERS

U-2115RB-00

U-2115RS-00

U-2115RS-01

U-2115RS-02

U-2115RSOD-00

U-2115RSOD-01

U-2115RW-00

U-2175RCB-00

WINE CAPTAIN®

MODELS

U-2115WCOL-00

U-2115WCS-00

U-2115WCS-01

U-2175WCCOL-00

U-2175WCCOL-02

U-2175WCCOL-60

U-2175WCCS-00

U-2175WCCS-01

U-2175BEVCOL-00

U-2175BEVCOL-02

U-2175BEVCOL-60

U-2175BEVCS-00

U-2175BEVCS-01

U-2175BEVCS-02

U-2175BEVCS-13

U-2175RCB-02

U-2175RCS-00

U-2175RCS-01

U-2175RCS-22

U-2175RCW-00

U-2175RSOD-00

U-2175RSOD-01

U-2175WCCS-02

U-2175WCCS-13

U-2175WCCS-22

U-2275ZWCOL-00

U-2275ZWCS-00

U-2275ZWCS-01

The American Built-In Undercounter Leader Since 1962

U-LINE.COM

Ta b l e o f C o n t e n t s

1 - Safety Precautions

Safety Alert Definitions.........................................................................................................................................1

General Precautions..............................................................................................................................................1

2 - Inspect & Plan

Product Registration .............................................................................................................................................2

Models Covered.....................................................................................................................................................2

Tools / Material Required ....................................................................................................................................2

Exterior Cleaning ...................................................................................................................................................2

3 - Prepare Site

Electrical Specifications.........................................................................................................................................3

Cut-Out Dimensions.............................................................................................................................................3

4 - Product Dimensions

5 - Door Swing Dimensions

Other Site Requirements.....................................................................................................................................6

6 - Doors (Self-Closing)

Door Alignment and Adjustment.......................................................................................................................7

Door Reversability.................................................................................................................................................7

Reversing Black or White Doors.......................................................................................................................8

Reversing Stainless Steel Glass Doors ..............................................................................................................9

7 - Wood Trim Finishing

8 - Door Panel Installation

Custom 1/4'' Thick Door Panel Insert............................................................................................................13

9 - Wood Grille Overlay

Grille Overlay .......................................................................................................................................................14

10 - Overlay Frame

11 - Installation

Leveling Information............................................................................................................................................20

Installation..............................................................................................................................................................20

Black and White Models:........................................................................................................................... 2

Stainless Models:.......................................................................................................................................... 2

2115 Series ................................................................................................................................................... 3

2175 Series ................................................................................................................................................... 3

2275 Series ................................................................................................................................................... 3

2115R, 2115WC(OL) & 2175RC Series................................................................................................ 4

2175BEV, 2175WC & 2275ZWC Series............................................................................................... 5

Side-By-Side Installation............................................................................................................................. 6

Power Supply ............................................................................................................................................... 6

Environmental Requirements................................................................................................................... 6

Staining and final finish application: ...................................................................................................... 12

Final finish-only application: ................................................................................................................... 12

Door Panel Preparation.......................................................................................................................... 13

Panel Dimensions..................................................................................................................................... 13

Door Panel Installation ........................................................................................................................... 13

Preparation................................................................................................................................................ 14

Installation.................................................................................................................................................. 14

Frame Preparation ................................................................................................................................... 17

Prepare the New Overlay Panel........................................................................................................... 18

Attaching the Overlay Panel.................................................................................................................. 18

Assembling Door to Cabinet ................................................................................................................ 19

Relocating the Shelves............................................................................................................................. 20

Installation Troubleshooting.................................................................................................................. 20

NOTICE

DANGER

!

WARNING

!

CAUTION

!

1 Safety Precautions

General Precautions

Use this appliance for its intended purpose only. Follow these
general precautions with those listed throughout this guide:

• PLEASE READ all instructions before installing,
operating, or servicing the appliance.

• Proper installation procedures must be followed when
completing an installation or relocation of a unit. An
INSTALLATION GUIDE for the unit, providing
complete installation information, is available from
U-Line Corporation direct. Consult the installation
guide before any installation begins. U-Line contact
information appears on the rear cover of this guide.

• This unit requires connection to a dedicated 15 Amp
grounded (three-prong), polarized receptacle, installed
by a qualified electrician, compliant with applicable
electrical codes.

Safety Alert Definitions

Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:

Danger means that failure to follow this safety statement will
result in severe personal injury or death.

Warning means that failure to follow this safety
statement could result in serious personal injury or
death.

Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.

DANGER

!

RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.

WARNING

!

SHOCK HAZARD - Electrical Grounding Required.

• Never attempt to repair or perform maintenance on
the unit until the electricity has been disconnected.

• Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.

• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and or loss of property and
or life, and will void the warranty.

• Never use an extension cord to connect power to the
unit.

• Always keep your working area dry.

WARNING

!

Install provided Anti-Tip kit. Serious personal injury
could occur.

CAUTION

!

• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.

• If your model requires defrosting, DO NOT use an ice
pick or other sharp instrument to help speed up
defrosting. These instruments can puncture the inner
lining or damage the cooling unit. DO NOT use any type
of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.

NOTICE

• Do not lift unit by door handle.

• Never install or operate the unit behind closed doors.
Be sure front grille is free of obstruction. Obstructing
free airflow can cause the unit to malfunction and will
void the warranty.

• Failure to clean the condenser every six months can
cause the unit to malfunction. This could void the
warranty.

• Allow unit temperature to stabilize for 24 hours before
use.

• Do not Block any internal Fans.

Use only genuine U-Line replacement parts. Imitation
parts can damage the unit, affect its operation or
performance and may void the warranty.

u-line.com 1

2 Inspect & Plan

Product Registration

You have received a carton containing your U-Line Refrigerator,
Refrigerator Freezer, Beverage Center or Wine Captain® unit
with a package inside containing a Use and Care Guide, a Product
Registration Card, and a water line kit. Please complete and mail
the Product Registration Card or register online at
www.U-LineService.com. Once your unit is installed, keep the Use
and Care Guide and this Installation Guide in a safe place for future
reference.

Models Covered

This installation guide covers the following models.

Tools / Material Required

• Screwdrivers — slotted and Phillips head

(Models ending in OL Only)

• 3/4" overlay frame material

• Cutting Tools

• Drill & Drill Bits

(Optional Door Panel on 2115R(F) or 2175R(F) Black or White Models)

• 1/4" thick door panel material

• Cutting Tools

(Optional WC & BEV Wood Trim Finishing)

• Minwax® Water-Based Wood Stain

• Minwax® Polycrylic® Protective Finish

• Foam Applicator and / or Synthetic Bristle Brush

• 220 grit Sandpaper

• 280 grit Sandpaper

(Optional Overlay kits for Non-OL models)

U-2115RB-00 U-2175RCGS-00

U-2115RS-00 U-2175RCGS-01

U-2115RS-01 U-2175RCS-00

U-2115RS-02 U-2175RCS-01

U-2115RSOD-00 U-2175RCW-00

U-2115RSOD-01 U-2175RFB-00

U-2115RW-00 U-2175RFS-01

U-2115WCOL-00 U-2175RFW-00

U-2115WCS-00 U-2175RSOD-00

U-2115WCS-01 U-2175RSOD-01

U-2175BEVCOL-00 U-2175WCCOL-00

U-2175BEVCOL-02 U-2275WCCOL-02

U-2175BEVCOL-60 U-2275WCCOL-60

U-2175BEVCS-00 U-2175WCCS-00

U-2175BEVCS-01 U-2175WCCS-01

U-2175BEVCS-02 U-2175WCCS-02

U-2175BEVCS-13 U-2175WCCS-13

U-2175RCB-00 U-2175WCCS-22

U-2175RCB-02 U-2275ZWCOL-00

U-2175RCS-22 U-2275ZWCS-00

U-2175RFS-00 U-2275ZWCS-01

U-2175RCGOL-00

Model Panel Kit (Black) Panel Kit (White)

2115R U-OL2115B U-OL2115W

2175R U-OL2175B U-OL2175W

2175RF U-OL2175B U-OL2175W

Exterior Cleaning

Black and White Models:

• Black and White surfaces may be cleaned with a mild detergent

and warm water solution. Do not use solvent-based or abrasive
cleaners. Use a soft sponge and rinse with clean water. Wipe
with a soft, clean towel to prevent water spotting.

Stainless Models:

• Stainless door panels, handles and frames can discolor when

exposed to chlorine gas, pool chemicals, salt water or cleaners
with bleach.

• Keep your Stainless unit looking new by cleaning with a good

quality all-in-one stainless steel cleaner/polish on a monthly
basis. For best results use Claire Stainless Steel Polish and
Cleaner, which can be purchased from U-Line Corporation
(Part numbers 173348).

• Do not clean with steel wool or abrasive pads.

• Do not use cleaners that are not specifically intended

for stainless steel on stainless surfaces (this includes
glass, tile and counter cleaners).

• If any surface discolors or rust appears, clean it quickly with

Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive
cloth. Always clean in the direction of the grain. Always finish
this process with Claire Stainless Steel Polish and Cleaner or
comparable product to prevent further problems.

Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of the
rust may not be possible.

2 u-line.com

CAUTION

!

NOTICE

WARNING

!

NOTICE

3 Prepare Site

24”

1-1/2"

15-1/4"

7"

34-1/8"

to

35"

4"

7"

24"

24-1/4"

34-1/4"

to

35-1/8"

24"

1-1/2"

24-1/4"

7"

Your U-Line product has been designed for either free-standing or
built-in installation. When built-in, your unit does not require
additional air space for top, sides, or rear. However, the front grille
must NOT be obstructed and clearance is required for an
electrical connection in the rear.

• Unit can NOT be installed behind a closed cabinet door.

Electrical Specifications

SHOCK HAZARD — Electrical Grounding Required.

• Never remove the round grounding prong from the
plug and never use a two-prong grounding adapter.

• Never use an extension cord to connect power to the
unit.

Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (three­prong), polarized receptacle that has been placed by a
qualified electrician.

The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A
power supply (normal household current). An individual, properly
grounded branch circuit or circuit breaker is recommended. GFCI
(ground fault circuit interrupter) is usually not required for fixed
location appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be sure to
consult your local codes.

2175 Series

Follow the cut-out drawing The 24-1/4" width allows 1/4" for ease
in installation and removal of the unit. 24" is the cabinet depth in
most installations.

2275 Series

Follow the cut-out drawing The 24-1/4" width allows 1/4" for ease
in installation and removal of the unit. 24" is the cabinet depth in
most installations.

See below for recommended receptacle location.

Cut-Out Dimensions

2115 Series

Follow the cut-out drawing. The 15-1/4" width allows 1/4" for ease
in installation and removal of the unit. 24" is the cabinet depth in
most installations.

u-line.com 3

4 Product Dimensions

23-1/16"

34-1/8"

24"

2175R(C)(F) Black and White Models

2175R(C)(F)S(G) Stainless & Out Door Models

2175R(C)(F)S Overlay Models

24"

24"

34-1/8"

34-1/8"

3-13/16"

23-1/16"

22-5/8"

3-13/16"

3-13/16"

23-1/4"

34-1/8"

15"

15"

34-1/8"

2115R Black / White Models

2115RS Stainless & Outdoor Models

3-13/16"

3-13/16"

23-1/8”

2115WCS Stainless Steel Models

15"

2115WCOL Wood Overlay Models

23-1/2"

*Not Including Wood Overlay Panel

3-13/16"

34-1/8"

34-1/8"

15"

3-13/16"

23-1/4"

2115R Series 2115WC / 2115WCOL Series 21175RC/RCG/RF Series

2115R, 2115WC(OL) & 2175RC
Series

4 u-line.com

34-1/8"

23-15/16"

22-5/8"

34-1/8"

2175BEVCS Stainless Steel Models

2175BEVCOL Wood Overlay Models

23-1/4"

3-13/16"

23-15/16"

3-13/16"

34-1/8"

24"

22-5/8"

34-1/8"

24"

2175WCCS Stainless Steel Models

2175WCCOL Wood Overlay Models

23-1/4"

3-13/16"

3-13/16"

2175BEV, 2175WC & 2275ZWC Series

22-5/8"

24"

34-1/8"

2275ZWCOL Wood Overlay Model

34-1/8"

23-1/4"

24"

2275ZWCS Stainless Steel Model

3-13/16"

3-13/16"

2175BEVC Series

2175WCC Series

2275ZWC Series

u-line.com 5

5 Door Swing Dimensions

1/4" Min.

Wall

21"

Wall

21"

16-1/2" 16-1/2"

2" Min.

90

Door Swing

90

Door Swing

Black and White Models

2115R Models

Stainless Models

Wall Wall

21"

16-1/2"

2" Min.

90

Door Swing

Stainless Steel

21"

16-1/2"

90

Door Swing

Black, White and Wood Overlay

1/4" Min.

2115WC Models

1/4" Min.

Wall

Wall

2" Min.

90

Door Swing

Black and White Stainless Steel

90

Door Swing

21"

25-1/2"

21"

25-1/2"

2175R(F) & 2275WC Models

90

Door Swing

Wall Wall

21"

25-1/2"

90

Door Swing

21"

25-1/2"

Stainless Steel

Wood Overlay

2" Min.

1/4" Min.

2175BEV

90

Door Swing

Wall Wall

21"

25-1/2"

90

Door Swing

21"

25-1/2"

Stainless Steel

2175WC Models

2" Min.

Black, White and Wood Overlay

Units have a zero clearance for the door to open 90°. Stainless
Steel models require 2-1/8" door clearance to accommodate the
handle if installed next to a wall.

Other Site Requirements

Side-By-Side Installation

For a complete refreshment center, install two units side by side:

Cut-out width for a side-by-side installation is the total of the
widths listed under Cut-Out Dimensions in each unit’s Installation
Guide.

No trim kit is required. However, 1/4-inch space needs to be
maintained between the units to ensure unobstructed door swing.

Units must operate from separate, properly grounded electrical
receptacles placed according to each unit’s Electrical Specifications
Requirements

Power Supply

The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A
circuit (normal household current). See Electrical Specifications.

Environmental Requirements

6 u-line.com

The units are designed to operate between 50°F (10°C) and 100°F
(37°C). High ambient temperatures (100°F [37°C] or higher) may
reduce the unit’s ability to reach low temperatures and may also
reduce the ice production rate for those models with icemakers.

If the ambient temperature is expected to drop below 45°F (7°C),
drain all water from the unit to prevent freezing damage, which is
not covered by the warranty.

For best performance, keep the unit out of direct sunlight and away
from heat generating equipment.

In climates where high humidity and dew points are present,
condensation may appear on outside surfaces. This is considered
normal. The condensation will evaporate when the humidity drops.

2115RSOD & 2175SOD Models: For best performance and life
outdoors, place under a counter or provide shelter of some kind.

NOTICE

6 Doors (Self-Closing)

1/8"
(3.175 mm)

1

23

23

1

Door Alignment and Adjustment

Align and adjust the door if it is not level, or is not sealing properly.
If the door is not sealed the unit may not cool properly, or
excessive frost may form in the interior.

• Properly aligned, the door’s gasket should be firmly in

contact with the cabinet all the way around the door
(no gaps). Carefully examine the door’s gasket to ensure
that it is firmly in contact with the cabinet. Also make
sure the door gasket is not pinched on the hinge side of
the door.

• The door will not be flush with the top of the cabinet.

The top edge of the door will be 1/8 in. (3.175 mm)
below the cabinet top.

To align and adjust the door:

1. Compare the top edge of the door (opposite the hinges) to the

top edge of the cabinet and note the type (up or down) of
adjustment needed.

2. Remove the top hinge pivot pin with a Phillips screwdriver and

lift door off bottom hinge pin. Be careful not to lose the door
closer insert sets.

3. Turn the door upside down and inspect the hinge plate mounting

holes. The plate has slotted mounting holes. Loosen but do not
remove the two hinge plate screws (1).

4. If door edge opposite the hinges needs to move up, move plate

toward outside of door (2). If door edge needs to move down,
move plate toward inside of door (3). Repeat until top edge of

4

door is parallel with top of cabinet and tighten screws (1)
securely.

5. After adjustment is complete, remove the door closers from the
bottom hinge, clean thoroughly and apply petroleum jelly to the
mating surfaces of the closers. Be sure that pins on closers align
with holes in the door and bottom cabinet hinge plates. Mount
door and install top hinge pivot pin.

Door Reversability

Location of the unit may make it desirable to mount the door on
the opposite side of the cabinet. Many doors are reversible. See
table below.

Model Reverse Model Reverse

U-2115RB-00 YES U-2175WCCOL-02 YES
U-2115RS-00 NO U-2175WCCOL-60 YES
U-2115RS-01 NO U-2175WCCS-00 YES

U-2115RS-02 NO U-2175WCCS-02 YES
U-2115RSOD-00 NO U-2175WCCS-13 YES
U-2115RSOD-01 NO U-2175WCCS-22 YES

U-2115RW-00 YES U-CLR2160B-00 YES

U-2115WCOL-00 YES U-CLR2160B-40 YES

U-2115WCS-00 YES U-CLR2160S-00 NO
U-2175BEVCOL-00 YES U-CLR2160S-01 NO
U-2175BEVCOL-02 YES U-CLR21060S-40 NO
U-2175BEVCOL-60 YES U-CLR2160S-41 NO

U-2175BEVCS-00 YES U-CLR2160SOD-00 NO
U-2175BEVCS-02 YES U-CLR2160SOD-01 NO

U-2175RCB-00 YES U-CLR2160SOD-40 NO
U-2175RCB-02 YES U-CLR2160SOD-41 NO

U-2175RCGOL-00 YES U-CLR2160W-00 YES

U-2175RCGS-00 YES U-CLR2160W-40 YES

U-2175RCS-00 NO U-CLRCO2175B-00 YES
U-2175RCS-01 NO U-CLRCO2175B-40 YES
U-2175RCS-22 NO U-CLRCO3286S-00 NO

U-2175RCW-00 YES U-CLRCO2175S-01 NO
U-2175RSOD-00 NO U-CO2175FS-01 NO
U-2175RSOD-01 NO U-CO2175FW-00 YES

U-2175WCCOL-00 YES

u-line.com 7

Reversing Black or White Doors

3

1

4

• The hinge hardware will be removed and reinstalled on the
opposite side of the cabinet.

• The top hinge hardware will be reinstalled on the bottom of the
opposite side of the cabinet.

• The bottom hinge hardware will be reinstalled on the top of the
opposite side of the cabinet.

Remove Door

2

1. Hold door to keep it from falling.

2. Remove hinge screw pin (1) from top hinge using a Phillips
screwdriver.

3. Remove door by tilting forward and lifting door off bottom hinge
closer inserts.

4. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.

Remove hole plugs.

Remove plastic screw plugs (three each, top and bottom)
from new hinge location. Save for reinstallation later.

Remove existing top hinge.

Remove existing top hinge (three screws) (2).

(3)

4

Reinstall hinge to bottom opposite.

1. Install the hinge just removed from the top to the BOTTOM
opposite side of the cabinet (three screws) (2).

2. Remove the two door closer inserts (4) from the existing
bottom hinge.

3. Install door closer inserts as shown on the new bottom hinge
(4).

8 u-line.com

Remove preexisting bottom hinge.

1

5

NOTCH

3

1

Screws

Top Of Door

Pivot Plate

Screws

Bottom Of Door

1. Remove the preexisting bottom hinge (three screws) (2).

Reinstall hinge to top opposite.

1. Install the hinge just removed from the bottom to the TOP
opposite side of the cabinet (three screws) (2).

Reinstall Hole Plugs.

1. Install plastic screw plugs (three each, top and bottom) (3) into
holes where hinge hardware was removed.

Reversing Stainless Steel Glass Doors

Remove Door

2

1. Hold door to keep it from falling.

2. Remove hinge screw pin (1) from top hinge using a Phillips
screwdriver.

3. Remove door by tilting forward and lifting door off bottom hinge
closer inserts.

4. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.

Remove hole plugs.

1.

Remove plastic screw plugs from (three each, top and bottom)
(3)

from new hinge location. Save for reinstallation later.

Prepare door for reinstallation.

1. Remove plastic hole plug from top of door handle and reinstall
on opposite side.

2. With bottom of door facing up, remove pivot plate (5) (two
screws).

3. Flip over and install pivot plate on opposite side of door. Ensure
notch in plate faces center.

Install Door.

1. Hold door upright and tilted forward.

2. Lift door on to bottom hinge closer inserts.

3. Tilt door forward into position.

4. Hold door to keep it from falling.

5. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.

Align and adjust the door:

Align and adjust the door, see DOOR ALIGNMENT AND
ADJUSTMENT on page 7.

Remove Stainless Frame

1. Remove two screws from top of door. Save screws for later
installation.

2. Remove pivot plate from bottom of door by removing 2 screws.
Set pivot plate and screws aside for later installation.

u-line.com 9

3. Grasp outer edge of stainless frame and firmly press inside edge

Push Glass

In

Pull Frame

Away

Door Orientation Right Hand Hinge

Logo

Door Orientation Left Hand Hinge

Logo

Pivot Plate

Flat Edge

Door Edge

1

2

4

of glass in while pulling stainless frame in opposite direction.

4. Unhinge frame from door.

3. Swing door into frame.

4. Install screws removed in “Remove Stainless Frame” step 1 to
top of door, opposite handle.

5. Install pivot plat to bottom of door, opposite of handle, using
hardware removed in “Remove Stainless Frame” step 2. Arrange
pivot plate so the flat edge is against the edge of the door.

Orient Hinge

1. Remove existing top hinge (three screws) (2).

Assemble Stainless Frame

1. Prop frame against solid surface, handle side down and away

2. Insert door, logo forward, into frame at a 30° angle. For a right
hand hinge the logo should be to your right. For a left hand hinge
the logo should be to your left.

Reinstall hinge to bottom opposite.

1. Install the hinge just removed from the top to the BOTTOM
opposite side of the cabinet (three screws) (2).

2. Remove the two door closer inserts (4) from the preexisting
bottom hinge.

4

3. Install door closer inserts as shown on the new bottom hinge
(4).

10 u-line.com

Remove existing bottom hinge.

1. Remove the existing bottom hinge (three screws) (2).

Reinstall hinge to top opposite.

1. Install the hinge just removed from the bottom to the TOP
opposite side of the cabinet (three screws) (2).

Reinstall Hole Plugs.

Install plastic screw plugs (three each, top and bottom)

1.
holes where hinge hardware was removed.

Install Door.

1. Hold door upright and tilted forward.

2. Lift door on to bottom hinge closer inserts.

3. Tilt door forward into position.

4. Hold door to keep it from falling.

5. Reinstall hinge screw pin (1) into top hinge using a Phillips
screwdriver.

Align and adjust the door:

Align and adjust the door, see DOOR ALIGNMENT AND
ADJUSTMENT on page 7.

(3)

into

u-line.com 11

CAUTION

!

NOTICE

7

Wood Tri m Fi nis hin g

To prevent permanent damage to the inner liner of the
unit, the wire rack wood trim MUST be removed from the
unit for staining and/or finishing. Allow stain/finish to dry
thoroughly (at least 24 hours) in accordance with the
stain/finish manufacturer’s instructions, prior to re­installing the wood trim inside the cabinet of the unit.
Failure to do so may cause the inner liner of the unit to
have a permanent odor, which is not covered by the
warranty.

• Your model may contain an electronic display panel in

the lowest level trim piece. After removing the trim
screws and gently pulling the trim from its location, a
wiring harness connector will become visible. Unplug
the connector and remove the trim from the interior.

• Glass in door is tinted. Stain may look darker when door

is closed.

Removing Wire Racks

1. Grasp the end of the rack, and gently slide it out until it stops.

2. Remove any bottles stored on the rack.

3. Press the left rack release lever (see above) down, and at the
same time, lift the corresponding right rack release lever up, and
pull the rack out until it is free of the tracks and the cabinet.

4. Do not remove the track side rails from the cabinet.

To insert a rack in the cabinet:

Staining and final finish application:

NOTICE

DO NOT use oil-based stains on wood trim. Vapors from
oil-based stains will permanently penetrate the liner and
will not dissipate over time.

1. Remove all screws securing wood trim to interior parts, and
remove the trim from the cabinet interior.

2. Lightly sand and clean wood.

®

3. Apply Minwax
synthetic bristle brush or a foam applicator. Allow stain to
penetrate about three minutes. Before the stain is dry, take a
stain dampened rag and remove any excess stain remaining.
Wipe towards the grain with medium pressure to achieve the
desired stain color.

4. After two hours, repeat step 2. This will even out the color of
the wood.

5. Allow stain to dry for a minimum of three hours before applying
the final finish.

6. If desired, sand the wood with very fine sandpaper to smooth
the surface after staining.

7. Remove all dust from the wood, and apply one coat of Minwax
Polycrylic® Protective Finish using a synthetic bristle brush to
the wood. Apply this finish in a thin coat following towards the
grain. Apply the finish to the back and sides of the wood first,
and allow it to dry for two hours. Apply the finish to the front
side of the wood next, and allow it to dry for two hours. Sand
with very fine 220 grit sandpaper. Apply two morel coats of
finish in the same manner, but do not sand the trim after applying
the final third coat.

8. Allow the final coat to dry for 24 hours before reinstalling the
trim to the cabinet interior parts.

Water-Based Wood Stain to wood with a

®

Final finish-only application:

1. Remove all screws securing wood trim to interior parts, and

2. Lightly scruff sand the wood trim with 280 or finer grit

3. Remove sanding dust with a clean, dry cloth.

4. The factory-applied seal is compatible with almost all finishes. A

1. Align the left and right rack channels with the tracks in the
cabinet, and ensuring an even track engagement on both sides,
gently push the rack into the cabinet until it stops.

Before reloading the rack, ensure proper operation of the travel
stops in the left and right track rails by pulling the rack out gently
until it completely stops.

12 u-line.com

5. Lightly sand and reapply if desired.

Allow the final coat to dry for 24 hours before reinstalling the trim
to the cabinet interior parts.

remove the trim.

sandpaper.

low odor, water clean up, quick-drying finish such as Minwax
Polycrylic
Polycrylic® is an ultra fast-drying water-based finish). Apply a
thin coat of a clear, protective finish, following the container
label directions.

®

Protective Finish is recommended (Minwax®

®

NOTICE

CAUTION

!

8 Door Panel Installation

Custom 1/4'' Thick Door Panel Insert

Door Panel Preparation

A custom door panel may be inserted into the doorframe. Custom
door panels can be flat or raised, as long as the maximum panel
thickness, where inserted into the door reveal (channel), is no
more than 1/4" thick. For raised panels, the depth of the reveal is
1/4" on all four sides.

Raised panels will reduce the door’s 90° swing/zero
clearance if the unit is installed next to a wall or similar
type of structure.

Panel Dimensions

The door panel must not weigh more than 20 lbs.

Model Width Height

2175R(C)(F) 23-1/32" 27-11/16"

2115R(C)(F) 14-1/32" 27-11/16"

3. Remove the two outside screws holding
door handle. Slightly separate door
handle from door.

4. Pull handle up and off.

5. Slide custom door panel insert into 1/4­inch channel in door front.

NOTICE

Use care not to damage magnet, located on door bottom,
when installing door insert. Do not set door on bottom
edge when pushing insert into place.

6. Holding door gasket out of the way, replace handle on door,
making sure it is seated properly on insert and that screw holes
line up.

Step 3

7. Install two small screws removed in

8. Starting at the corners and working inward, push door gasket
into place on door.

9. Place door on bottom hinge pin and install upper hinge screw.

.

Door Panel Installation

Install the insert as follows:

Use care when handling the insert. Insert edges may be
sharp.

1. Remove top hinge screw pin with Phillips head screwdriver.
Remove door by tilting forward and lifting off bottom hinge pin.

2. Pull door gasket out of groove (top edge of door only). Start in
the middle and pull outward, moving toward the edge. This may
take some force.

u-line.com 13

CAUTION

!

CAUTION

!

NOTICE

9 Wood Grille Overlay

Remove Screw

Remove Screw

Back

Front

Wood Overlay

Grille

24 Inch Models

Application

Area

Back

Front

Wood Overlay

Grille

15 Inch Models

Application

Area

Grille Overlay

Your model’s grille is designed to accept a wood grille overlay. An
overlay may be used to compliment a door overlay and provides a
seamless look for your surrounding decor. Follow the instructions
below to prepare and install your grille overlay. Be sure to read
over this chapter completely before beginning.

Preparation

The grille overlay MUST have venting as shown in the
drawing below. Failure to have proper venting can result in
damage to your model.

The grille overlay may only be installed on indoor units.

1. Prepare your overlay using the dimensions provided in the
figure on page 15 for 24 inch models and page 16 for 15 inch
models. If using a hook and loop style mount, drill hole A will
not be used.

2. If desired, stain and finish your grille to match your surrounding
decor. Follow the stain manufacturers instructions to apply stain
to your overlay.

Hook and Loop Fastener Mount

You may also mount your overlay to your grille using hook and
loop type fasteners. U-Line recommends using 3M® Dual lock®
fasteners. To mount your overlay using a hook and loop fastener
follow the instructions below.

1. Read the instructions provided with your hook and loop
fastener carefully.

2. Apply hook and loop fastener system to the back of the overlay
and front of the grille. Use the shaded areas in the diagram
below for application location.

Installation

The wood overlay grille must be installed in such a
manner that the grille assembly can still be removed from
the unit.

Screw Mount (Recommended)

1. Remove the grille from your unit by removing the two
mounting screws. See below.

2. Lay the back of your grille overlay onto the front of the grille.
Make certain the screw holes and vents are aligned.

3. Slide each of the screws removed in step 1 through the grille
overlay and grille.

4. Mount your new overlay onto your unit by screwing the overlay
back onto the base of your unit.

14 u-line.com

3. Carefully align the wood overlay with the grille and press into
position.

1/4

8-1/2

3-3/32

19-5/8

1/2

1/2

TYP 3X

5/16

TYP 2X

(7/16 )

5/16

10-5/16

11/64

2-1/8

1/2

22-7/8

23-7/8

FULL R

Grille Overlay Dimensions 24 Inch Models

Grille Drawing 24 inch

u-line.com 15

1/4

4-5/32

3-3/32

10-5/8

1/2

1/2

TYP 3X

5/16

TYP 2X

(15/32 )

.275

5-29/32

11/64

2-1/8

1/2

13-7/8

14-7/8

FULL R

Grille Overlay Dimensions 15 Inch Models

Grille Drawing 15inch

16 u-line.com

NOTICE

10 Overlay Frame

9/32

See Detail C

3/4"

Detail C
Scale 2:1

Door bottom
Ø 3/8" x 1/4" deep
Chamfer 1/32" x 45°

Detail A
Scale 2:1

Door top
Ø 3/16" x 11/16" deep

9/32"

3/8"

See Detail A

Dim. B

NOTE: Front view of
wood panel with
right-hand hinge shown
(mirror image
for left-hand hinge)

Section A-A

Scale 2:1
Typ 4 places

NOTE: Final component
is only a picture frame.
No panel inside of rails.
(Excludes -60 Models)

(Excludes -60 Models)

Right-hand
isometric view
shown.
Opposite
for left-hand

A

A

Dim. A

3/4"

2-1/4"

Dimension A Table

Model

Dimension A

2275ZWCOL

2175WCCOL

2175BEVCOL

2115WCOL

23-3/4"

23-3/4"

23-3/4"

14-3/4"

(See Table)

Dimension B Table

Toe KickToe Kick Dim. BDim. B

3-3/4"

3-7/8"

4"

4-1/8"

4-1/4"

4-3/8"

4-1/2"

29-3/4"

29-3/4"

29-5/8"

29-1/2"

29-3/8"

29-1/4"

29-1/4"

Frame Preparation

2115WCOL 2175WCCOL & 2175BEVCOL Models Only

An overlay frame covers the door frame to give a built-in
appearance. Appropriate hardware and a copy of these
instructions will be included with the unit.

The thickness of the overlay panel must be 3/4".

1. Use the following instructions to create or have a wood
overlay panel created for you Wine Captain® or beverage
Center model as shown below.

2. Drill holes for pivot pins, upper door hinge and lower door
hinge as shown.

u-line.com 17

Prepare the New Overlay Panel

NOTICE

The overlay door panel must not weigh more than 20 lbs.
The thickness of the door panel must be 3/4".

1. Place a towel, or similar, soft non-marking material out on a flat
clean surface. Be sure the material is large enough to have the
wood panel not touch the hard mating surface.

2. Lay the wood panel out with the front side of the wood facing
down.

3. Cut the foam tape in to four pieces, two pieces the width of the
overlay and two pieces the height of the overlay.

4. Remove adhesive protection strip from one piece of the cut
foam and align the edge of the foam tape to the inside edge of
the overlay as shown, adhering the foam tape to the overlay. See
below.

2. Carefully lay the door over the wood panel, making sure door is
oriented correctly (top of door with top of wood overlay).

3. Pull door gasket out of the groove completely. Start in the
middle and pull outward, moving towards the corners (see
below). This may take some force, but be careful not to cut or
rip the gasket.

5. Trim each piece of tape immediately after applying it to the
overlay. Do not allow any overlapping of the foam tape. Damage
to the overlay can occur is the foam tape is not trimmed
correctly.

6. If required, attach any optional cabinet hardware to the wood
panel at this time. If an optional cabinet handle is installed, make
sure the mounting screw heads are below (countersunk) the
back surface of the overlay.

Note: After attaching the optional cabinet hardware, additional
supports may be needed to keep panel flat for next steps.

4. After the gasket has been removed, place it on a clean, flat

5. Secure the door to the back of the wood overlay using tape on

Attaching the Overlay Panel

1. Remove the top hinge pivot pin with a Phillips screwdriver and
lift the door off bottom hinge pin. Be careful not to lose the
door closer insert sets. Save pivot pin for use later. See figure
in next column.

18 u-line.com

surface.

all four corners. Make sure all four edges are aligned. (See figure
on next page)

6. Use the door frame holes as a guide to drill pilot holes for the

NOTICE

TAPE

DOOR FRAME

BOTTOM OF
OVERLAY

TOP OF
OVERLAY

ULIN_0418_A

#6 x 1" Pan Head Screws
(10 Total)

Ta pe

Top Of Panel

Depending on installation
bottom of overlay may NOT
align with bottom of door

Door closers

#6x1" pan head screws.

Assembling Door to Cabinet

8. Starting at the corners and working toward the center, push the
door gasket back into place. Make sure the gasket is fully seated
on all four sides and corners.

9. Check the closure assembly on the bottom hinge to be sure it is
seated correctly in the bosses in the hinge.

7. Attach the door to the overlay using #6x1" wood screws.

If you decide to drill pilot holes, remove the wood overlay
from the door, and do not use a drill larger than 7/64". Be
sure not to drill deeper than 3/8". The door frame and
wood overlay must be aligned properly or the door will
not operate correctly.

Note: After attaching the wood to the door, double check the
bottom pivot hole location. If the hole in the pivot bracket is
covered by any wood, chase through the hole with a 11/32" drill to
open hole in door panel. DO NOT drill deeper than 1/4".

10. Position door over closer. Be sure the door hinge plate holes
align with the bosses on the closer (see below). Failure to do so
will result in the door not sitting in the proper position and door
will not align correctly. (Sometimes it is helpful to open the door
180° to have the closer and pivot align correctly.)

11. Holding the door in the closed position, install the pivot post
through the top hinge into the top pivot plate. Tighten securely
with a Phillips screwdriver, making sure post is seated fully.

12. Adjusting the door as needed.

u-line.com 19

11

1

Turn Foot to Adjust

Problem

Solution

A:

Problem

Solution

A:

11 Installation

Leveling Information

It is recommended that the unit is level.

13. Use a level to check
the levelness of the
unit from front to
back and from side
to side. Level should
be placed along top
edge and side edge
as shown.

14. If the unit is not level, adjust the feet on the corners of the unit
as necessary (not available in CO29 models).

Installation

1. Plug in the powercord.

2. Gently push the unit into position. Be careful not to kink the
water supply line or entangle the electrical cord.

3. Re-check the leveling, from front to back and side to side. Make
any necessary adjustments. The unit’s top surface should be
approximately 1/8" below the countertop.

4. Remove the tape from the glass shelves and wipe out the inside
of the unit with a clean, water-dampened cloth.

Relocating the Shelves

Both the glass shelves in the refrigerator and the inner door
shelves can be moved to accommodate your bottles, cans and
containers.

Glass Shelves on Right-Hand Hinge Units

• Open door fully, grasp shelf firmly, lift front edge slightly, and

pull straight out.

• Choose new location and slide shelf onto the appropriate rib.

Glass Shelves on Left-Hand Hinge Units

• Pull shelf out about 6" to clear the wall’s molded protrusion.

• Tilt right-hand edge of shelf up.

• Keeping at this angle and hugging the right wall, pull the shelf

out.

• Choose new location and insert over ribs, tilting right-hand

edge up. Push in, then lower shelf onto ribs.

Door Shelves

15. Check the levelness after each adjustment and repeat the
previous steps until the unit is level.

INSTALLATION TIP

If the room floor is higher than the floor in the cut-out opening,
adjust the rear feet to achieve a total unit rear height of 1/8" less
than the opening’s rear height. Shorten the unit height in the front
by adjusting the front feet. This allows the unit to be gently tipped
into the opening. Readjust the front feet to level the unit after it is
correctly positioned in the opening.

• First pull shelf up at a 45° angle, then straight out.

• Choose new location and line up on bosses. First push straight
in, then down at a 45° angle.

Installation Troubleshooting

The door remains open unless it is pushed closed.

The hinges should be self-closing when the door is open
approximately 8". If this is not the case, make sure the closers are
clean, greased and installed correctly. Also, re-check leveling from
front to back of the unit and readjust if necessary. Make sure that
pivot plate is installed correctly.

The custom overlay door was designed to align with the rest of the
cabinet doors, but the unit has crept forward.

Make sure that the electrical cord and water supply line are not
obstructing the installation.

20 u-line.com

®

INSTALLATION GUIDE

PRODUCT INFORMATION

Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings,
Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable
Energy Guides are available for reference and download at u-line.com.

SERVICE INFORMATION

Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked
Questions are available at u-line.com under Customer Service. You may contact U-Line directly:

GENERAL INQUIRIES:

U-Line Corporation

P.O. Box 245040

Milwaukee, Wisconsin 53224-9540 U.S.A.

Phone [phone]

FAX [phone]

Email: [e-mail]

u-line.com

SERVICE ASSISTANCE:

Phone [phone]

FAX [phone]

Email: [e-mail]

u-lineservice.com

PARTS ASSISTANCE:

E-mail: [e-mail]

BUILDING ON THREE GENERATIONS OF INNOVATION

For over five decades and through three generations, U-Line continues to be the leader in innovation, quality and
performance in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line
has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired
innovation and attention to even the smallest details. We are known and respected for our unwavering dedication
to product design, quality and selection.

In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was the first
to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and determination
to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today. The newest
Uihlein generation continues to build upon the family’s innovative legacy at the Milwaukee, Wisconsin based business
by providing continuity and vision from which new designs and technology continue to be born.

Today the complete U-Line product collection includes Ice Makers, Ice Machines, Wine Captain® Models, Combo®
Models, Refrigerator / Freezers, Refrigerators, Drawer Models and Beverage Centers. The U-Line brand offers
products in the 1000 Series, 2000 Series and the Modular 3000 Series. The 1000 Series offers a more targeted
priced product with appropriate features, while the 2000 Series offers upscale features, advanced technology and
specialized product families. Our Modular 3000 Series provides sleek design and versatile temperature settings with
our U-Select® control. U-Line’s approach to its breadth of products, multiple price points and features allows a
choice and product that will fit any lifestyle.

DESIGNED, ENGINEERED AND ASSEMBLED IN WISCONSIN, USA

The American Built-In Undercounter Leader Since 1962

U-LINE.COM

Publication Number 30282 4/2013 Rev.J

©2013 U-Line Corporation