ULINE H-7033, H-7034, H-7035, H-7598, H-7599 Specifications
...
π
H-7598, H-7599, H-8362
ADJUSTABLE
HEIGHT DESK
TOOLS NEEDED
H-7033, H-7034, H-7035
Para Español, vea páginas 6-10.
Pour le français, consulter les pages 11-15.
1-800-295 -5510
uline.com
Drill 4 mm Hex Wrench
Desktop x 1 Adjustable Frame
Top Support
Bracket x 2
Power Cord x 1
(Included)
with Lifting Columns x 1
Control Box x 1
M6 x 33 mm
Machine Screw x 5
5 mm Hex Wrench
Programmable
Handset x 1
M6 x 15 mm Machine
Screw with Lock
Washer and Flat
Washer x 18
(Included)
PARTS
Foot with Leveling
Glides x 2
Cable
Management
Tray x 2
5 mm x 20 mm
Wood Screw x 11
# DESCRIPTION QTY.
1 Desktop 1
Adjustable Frame with
2
Lifting Columns
3 Foot with Leveling Glides 2
4 Top Support Bracket 2
5 Control Box 1
6 Programmable Handset 1
7 Cable Management Tray 2
8 Power Cord 1
9 M6 x 33 mm Machine Screw 5
M6 x 15 mm Machine Screw with
10
Lock Washer and Flat Washer
11 5 x 20 mm Wood Screw 11
12 4 mm Hex Wrench 1
13 5 mm Hex Wrench 1
18
1
ASSEMBLY
NOTE: Count and inspect all pieces before
disposing of any carton or packing materials.
NOTE: Two-person assembly is recommended.
CAUTION! Adjustable frame is heavy and
care should be used when moving it during
assembly.
1. Place adjustable frame with lifting columns on a
smooth, non-marring surface to prevent scratching.
NOTE: Lifting columns are pre-installed to
adjustable frame and are folded down toward
center of adjustable frame for shipping.
PAGE 1 OF 15 0421 IH-7033
2. Unfold the lifting columns to an upright position.
(See Figure 1)
Figure 1
Lifting
Column
2
ASSEMBLY CONTINUED
3. Insert top support bracket (4) into outside of
adjustable frame (2). Repeat this step on the
opposite side. (See Figure 2)
NOTE: Steel lip with three holes on top support
bracket should be facing down.
Figure 2
2
4
4. Insert two M6 x 33 mm machine screws (9) into holes on
end of adjustable frame to connect adjustable frame
with lifting columns
lightly tighten using 5 mm hex
and top support bracket
wrench (13). Then
and
lightly
tighten two pre-installed M6 x 33 mm machine screws (9)
to secure lifting column. Repeat this step on the
opposite side. (See Figure 3)
NOTE: To prevent alignment issues during this
step, do not tighten completely until all four
machine screws are inserted.
Figure 3
5. Attach foot (3) to lifting column using four M6 x 15 mm
machine screws (10). Tighten using 4 mm hex wrench (12).
(See Figure 4)
Figure 4
Column
12
10
3
Lifting
6. Place desktop (1) upside down on a smooth,
non-marring surface to prevent scratching.
Grommets should be facing down.
7. Place adjustable frame on top of desktop (1). Adjust
position of adjustable frame so that it is centered on
the desktop. (See Figure 5)
NOTE: Adjustable frame is designed to fit desktops
that are 48-72" long and 24-30" wide. Extend
adjustable frame as needed to position desktop.
For 48 x 24" and 60 x 24" desks, top support
brackets should be approximately 1½" from side
edges of desktop and approximately 2½" from
front and back edges of desktop.
For 48 x 30" and 60 x 30" desks, top support
brackets should be approximately 1½" from side
edges of desktop and approximately 5½" from
front and back edges of desktop.
For 72 x 24" desks, top support brackets should
be approximately 6" from side edges of desktop
and approximately 2½" from front and back
9
edges of desktop.
For 72 x 30" desks, top support brackets should
be approximately 6" from side edges of desktop
and approximately 5½" from front and back
edges of desktop.
13
1
Figure 5
PAGE 2 OF 15 0421 IH-7033
ASSEMBLY CONTINUED
8. Attach top support brackets and adjustable frame
to desktop using drill and eight 5 x 20 mm wood
screws (11). (See Figure 6)
Figure 6
11
11
11
11
10. Connect the power for the control box (5) using
the power cord (8). Connect the programmable
handset (6) and lifting column cables into the
control box. (See Figure 8)
5
Figure 8
5
Lifting Column
8
6
Cable
11. Position loose cords underneath the cable
management trays (7). Attach the cable
management trays to the adjustable frame using
eight M6 x 15 mm machine screws (10). Tighten
using 4 mm hex wrench (12). (See Figure 9)
9. Place programmable handset (6) in desired location
on front edge of desktop. Attach using a drill and
two 5 x 20 mm wood screws (11). (See Figure 7)
NOTE: Back of desktop has two grommet holes.
Front of desktop is the opposite side.
Figure 7
6
11
Figure 9
12
10
7
12. Desk is now fully assembled. Using two people,
carefully flip the desk onto the feet.
13. Plug power cord into outlet. Follow operation
instructions to initialize the desk prior to first use.
PAGE 3 OF 15 0421 IH-7033
CONTROLS
OPERATION
USB Charger
24.5
Up
Button
NOTE: The desk must be initialized prior to
first use.
• To initialize, press and hold the down button on the
handset until the desk reaches its lowest height,
slightly raises and stops.
• Release the down button. The desk is now ready to use.
NOTE: The desk may need to be reset from time
to time to work properly. Unplug the power cord
for 20 seconds, plug back in and follow the
initialization process to reset desk.
CAUTION! Make sure there are no obstacles in
the desk's height adjustment path, and make
sure the desk is not touching any walls.
CAUTION! Make sure all cords are at the
appropriate length to accommodate changes
in height.
Down
Button
Setting
Button
Display Four Preset
HEIGHT ADJUSTMENT
• Press the up button to raise the desktop.
• Press the down button to lower the desktop.
• Release button to stop movement.
CAUTION! To avoid overheating, do not move
the desk up and down continuously for over
two minutes within any 20 minute period. If the
heater overheats, OH will be displayed on the
handset. Stop using the desk for 20 minutes
and let it cool down.
Position Buttons
PROGRAMMING PRESET HEIGHT
• Use up and down buttons to move desk to the
desired position.
• Press and hold the setting button and one of the four
preset position buttons simultaneously.
• The handset will display 1CF, 2CF, 3CF and 4CF for
each preset when complete.
• Up to four presets can be programmed.
PROGRAMMING HEIGHT LIMITS
NOTE: Desk is equipped with a height limit function.
This function allows upper and lower height limits
to be programmed. This can be used to prevent
collisions with objects above and below the desk,
such as file pedestals and overhead cabinets.
• Use up and down buttons to move desk to the
desired upper height limit. Press and hold the setting
button and up button simultaneously. The upper
limit is set when HI is displayed. To cancel, press the
same buttons again. The upper limit is cancelled
when HCL is displayed.
• Repeat the process to set the lower limit. The lower
limit is set when LO is displayed. The lower limit is
cancelled when LCL is displayed.
• Always program height limits before programming
preset heights.
SWITCHING BETWEEN INCHES AND CENTIMETERS
• Press the setting button for seven seconds until SET
is displayed, and then press the first preset position
button. The default unit of measurement will be
displayed. Press the up and down button to change
between inches and centimeters.
PAGE 4 OF 15 0421 IH-7033
OPERATION CONTINUED
1
0
uline.com
PROGRAMMING ANTI-COLLISION SENSITIVITY
NOTE: Desk is equipped with a gyroscope with
an anti-collision feature. This feature allows for
various levels of sensitivity to prevent collisions
with objects above or below the desk.
• Press and hold the setting button for seven seconds
until SET is displayed, and then press the third preset
position button to enter the sensitivity setting mode.
• Press the up or down buttons to switch sensitivity
levels. Levels range from 1 to 8 where the higher
levels result in higher sensitivity. The default level is 5.
• Press the setting button to confirm the selection.
LOCKING OPERATION OF DESK
NOTE: Desk is equipped with a locking feature
to prevent operation.
• Press and hold the first and second preset position
buttons simultaneously for seven seconds until LoC
is displayed. The desk is now locked.
• Repeat the process to unlock.
TROUBLESHOOTING
OPERATING ISSUE RECOMMENDATIONS
Desk does not go up or
down.
Check all connections.
Ensure power cord is plugged into the control box and a power outlet.
Unplug the power cord for 20 seconds, plug back in and follow the initialization
process to reset desk.
Columns do not go up
evenly.
Desk does not reset, or
rSt, ER1, ER2 or ER3
displayed on handset.
Desk is unusually noisy.
OH displayed on handset.
If the troubleshooting section does not resolve your problem, contact Uline Customer Service at 1-800-295-5510.
Initialization/Reset Process:
• Press and hold the down button on the handset until the desk reaches its lowest
height, slightly rises and stops.
• Release the down button.
If initialization does not work, press and hold the setting button until "SET" is
displayed on handset. Then, while still pressing setting button, press the fourth
preset position button "IV" until "rSt" is displayed on handset. Press and hold the
down button until the desk reaches its lowest height.
If problem persists, switch motor cables at control box and attempt another reset.
The desk has two-stage legs that produce noise when one leg extends into the
other. To reduce noise, apply silicon lubricant to legs.
Desk is overheated. Stop adjusting desk height for 20 minutes to let desk cool
down.
-800-295-551
PAGE 5 OF 15 0421 IH-7033
Loading...