U-Line H-6499, H-6500 User Manual

π H-6499, H-6500

PORTABLE BLOWER

1-800-295 -5510

uline.com

GROUNDING

This appliance must be grounded. If it should

malfunction or breakdown, grounding provides a path

of least resistance for electrical current to reduce the

risk of electric shock. This appliance is equipped with
a cord having an equipment-grounding conductor
and grounding plug. The plug must be inserted into
an appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.

WARNING! Improper connection of the
equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided
with the appliance. If it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.

IMPORTANT SAFETY INSTRUCTIONS

Read and understand this owner’s manual and
all labels on the unit before operating. Safety is a
combination of common sense, staying alert and
knowing how the unit works. Use this unit only as
described in this manual. To reduce the risk of personal
injury or damage to your unit, use only Sanitaire
recommended accessories.

When using an electrical appliance, basic precautions
should always be followed, including the following:

WARNING! This appliance is for use on a
nominal 120-volt circuit and has a grounding
plug that looks like the plug illustrated below.
(See Figure 1) Make sure that the appliance
is connected to an outlet having the same
configuration as the plug. No adaptor should
be used with this appliance.

GROUNDED OUTLET

GROUNDING PIN

Figure 1

SAFETY

• Do not use a flammable or combustible liquid to
clean a floor.

• Do not use this unit near flammable liquids, gases
or explosive vapors like gasoline or other fuels,
lighter fluids, cleaners, oil-based paints, natural
gas, hydrogen or explosive dusts like coal dust,
magnesium dust, grain dust or gun powder. Sparks
inside the motor can ignite flammable vapors or
dust.

• Keep the cord away from heated surfaces.

WARNING! To reduce the risk of fire, electrical
shock or injury:

• Do not run the unit unattended.

• Use indoors only.

PAGE 1 OF 3 0217 I H -6 4 9 9

• Do not expose to rain. Store indoors in an area
above 32°F, where the machine will not freeze.

• Do not unplug by pulling on cord. To unplug, grasp
the plug.

• Do not use with damaged cord, plug or other parts.

SAFETY CONTINUED

• If the unit is not working as it should, has been
dropped, damaged, left outdoors or dropped into
water, contact Uline Customer Service.

• Do not pull or carry by the cord, use the cord as a
handle, close a door on a cord or pull cord around
sharp edges or corners.

• Do not run the unit over the cord.

• Do not handle the plug or the unit with wet hands.

• Do not store near hazardous materials.

• Do not allow it be used as a toy. Close attention is
necessary when used by or near children.

• To reduce the risk of injury from accidental starting,
unplug power cord before cleaning, making
adjustments or repairing.

• Turn off all controls before unplugging.

• Do not put any object into ventilation openings. Do
not operate with any ventilation openings blocked.
Keep free of dust, lint, hair or anything that may
reduce air flow.

• Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.

• To reduce the risk of falls, use extra care when using
the unit on stairs.

• Do not pick up flammable or combustible liquids,
such as gasoline, or use in areas where they may be
present.

• Do not use an extension cord with this unit.

• If the machine tips over during use, shut it off
immediately, set it upright and wait for the motor to
stop completely.

• Do not use machine in standing water.

NOTE: Save this manual for future reference.

OPERATING INSTRUCTIONS

1. Ensure machine is in a safe operating location. Do
not place machine in a puddle, and make sure it is
protected from drips and splashes.

2. Plug the power cord into a grounded electrical
outlet. Always unwind power cord completely before
operating machine. Inspect power cord for damage
before each use. Replace cord immediately if
damaged.

3. Place the machine in the desired operating position.
(See Figure 2)

a. Horizontal – Dry floors and carpets.

b. Tilted – Dry floor finishes, paint, etc.

c. Vertical – Dry wall and ceiling.

a b c

Figure 2

4. Set the desired speed by turning switch.

5. Check for proper operation before leaving the
machine unattended. Do not move or carry the
machine when it is operating.

6. To shut off machine, turn the switch to the off (O)
position. (See Figure 3)

Figure 3

7. The machine is equipped with an automatic reset
motor overload shutoff thermal sensor to protect
motor from overheating. Should the shutoff thermal
sensor trip, it will reset automatically when the motor
has cooled sufficiently, usually after 15-30 minutes.

PAGE 2 OF 3 0217 I H -6 4 9 9