SolarPoint
4x PoE Smart MPPT Charger
Model: SM-SP-40
Introduction
Thank you for purchasing the Ubiquiti Networks® SolarPoint®
MPPT Controller. This Quick Start Guide is designed to guide you
through installation and includes the warranty terms.
Package Contents
SolarPoint
Installation Requirements
• Phillips screwdriver
• Needle nose pliers
• Shielded Category 5 (or above) cabling should be used for all
wired Ethernet connections.
• We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial‑grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit: www.ubnt.com/toughcable
TERMS OF USE: Shielded Ethernet cable and earth grounding must be used as conditions of product
warranty. TOUGHCable™ is designed for outdoor installations. It is the professional installer’s
responsibility to follow local country regulations, including operation within legal frequency channels,
output power, and Dynamic Frequency Selection (DFS) requirements.
Hardware Overview
Interface
System LED
Reset
Button
Power
Ethernet
Ports
Output
LED
System
LED
Reset
Button
Battery
Terminal
Terminal
Description
Steady green when system is on;
Red when battery polarity is reversed.
There are two methods to reset the SM‑SP‑40
to factory defaults:
• Runtime reset (recommended) The SM‑SP‑40
should be running after bootup is complete.
Press the Reset button and the LED will turn
off as the SM‑SP‑40 reboots.
• Factory reset Press and hold the Reset
button for eight seconds to restore factory
default settings to the SM‑SP‑40.
Battery Terminal
Power Terminal
Ethernet Ports
Output LED
Four‑pin terminal block for NTC and battery
Two‑pin terminal block for power (24VDC out)
Supports 10/100 Fast Ethernet connections
and passive 24V, 2‑pair PoE output.
Steady green when power is enabled.
Hardware Installation
Pole Mounting
1. Open the Metal Strap and feed it through the mounting slots
on the back of the SolarPoint.
2. Wrap the Metal Strap around the pole. Use a 7 mm socket
wrench to turn the screw clockwise and securely fasten the
strap to the pole.
Opening the Port Cover
1. Press down and slide the port cover forward.
2. Lift the port cover up.
3. Remove the four‑pin connector from the terminal block using
the special tool attached to the underside of the port cover.
4. Place a crimp connector on one end of the wire.
5. Use a pair of needle nose pliers to crimp the connector onto
the end of the wire.
6. Insert the crimped wire into one of the open slots on the
four‑pin connector. Using a phillips screwdriver, secure the wire
to the connector by tightening the screw until it stops.
7. Repeat steps four through six until the connector is fully
occupied with all four wires.
8. Attach the NTC and battery cable.
Connecting Ethernet
1. Connect an Ethernet cable to one of the Ethernet ports.
Note: PoE is disabled by default.
2. When you are finished, close the port cover.
Specifications
SM‑SP‑40
Dimensions 202 x 186 x 50 mm (7.95 x 7.32 x 1.97")
Weight 650 g (1.43 lb)
Enclosure Characteristics UV‑Resistant Polycarbonate
Processor QCA9533
System Memory 512 DDR2
Storage 16 MB Flash; 64 MB EEPROM
Antenna Internal Polarity 2.4G PCB Band
Max. Power Consumption 5W
Max. Battery Charge 7A
Networking Interface (4) 10/100 Fast Ethernet Ports
Management Interface Ethernet + Wi‑Fi (2.4 GHz)
Button Reset
LEDs System; Output
Power Source Solar H4
PV Input 10‑60V
Operating Temperature ‑20 to 50° C (‑4 to 122° F)
Certications
FCC/IC/CE
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can be
submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified may result in improper operation, damage to
the equipment or pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be
provided only by a qualified service technician.
3. The equipment requires the use of the ground wire as a part of the safety
certification, modification or misuse can provide a shock hazard that can result in
serious injury or death.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s)
furnished hereunder (the “Product(s)”) shall be free from defects in material and
workmanship for a period of one (1) year from the date of shipment by UBIQUITI
NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and
exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI
NETWORKS, at its discretion, to repair or replace any Product that fails to conform to
the above warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty period of
any repaired or replaced Product shall not extend beyond its original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto, except by
Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as
approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical,
electromagnetic or electrical stress, including lightning strikes, or accident;
(V ) has been damaged or impaired as a result of using third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti
label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA.
In addition, the above warranty shall apply only if: the product has been properly
installed and used at all times in accordance, and in all material respects, with the
applicable Product documentation; all Ethernet cabling runs use CAT5 (or above),
and for outdoor installations, shielded Ethernet cabling is used, and for indoor
installations, indoor cabling requirements are followed.
Returns
No Products will be accepted for replacement or repair without obtaining a Return
Materials Authorization (RMA) number from UBIQUITI NETWORKS during the
warranty period, and the Products being received at UBIQUITI NETWORKS’ facility
freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products
returned without an RMA number will not be processed and will be returned freight
collect or subject to disposal. Information on the RMA process and obtaining an RMA
number can be found at: www.ubnt.com/support/warranty
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS,
ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND
HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION
OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING,
BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF
MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A
PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY WARRANTIES ARISING
FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH
SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI
NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT
OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO
LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS
INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS
AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR
ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS,
CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the
operation of the Products will be error‑free or that operation will be uninterrupted.
In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any
nature or description relating to system performance, including coverage, buyer’s
selection of products (including the Products) for buyer’s application and/or failure of
products (including the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI
OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT,
LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE,
OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY,
CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions of implied warranties
or conditions, so the above exclusion may not apply to you. You may have other
rights that vary from country to country, state to state, or province to province. Some
countries, states and provinces do not allow the exclusion or limitation of liability for
incidental or consequential damages, so the above limitation may not apply to you.
EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY
STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED
IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the
International Sale of Goods shall not apply to any transactions regarding the sale of
the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and complies with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operations of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense. This radio
transmitter (FCC ID: SWX‑SMSPW) has been approved by FCC.
ISED Canada
CAN ICES‑3(A)/NMB‑3(A)
This device complies with ISED Canada licence‑exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
This radio transmitter (IC: 6545A‑SMSPW) has been approved by ISED Canada.
CAN ICES‑3(A)/NMB‑3(A)
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Le présent émetteur radio (IC : 6545A‑SMSPW) a été approuvé par ISDE Canada.
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être installé en considérant une
distance de séparation de toute personnes d’au moins 20cm et ne doivent pas être
localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.
Australia and New Zealand
Warning: This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
CE Marking
CE marking on this product represents the product is in compliance with all directives
that are applicable to it.
RoHS/WEEE Compliance Statement
English
European Directive 2012/19/EU requires that the equipment bearing this symbol on
the product and/or its packaging must not be disposed of with unsorted municipal
waste. The symbol indicates that this product should be disposed of separately from
regular household waste streams. It is your responsibility to dispose of this and other
electric and electronic equipment via designated collection facilities appointed by
the government or local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and human health. For more
detailed information about the disposal of your old equipment, please contact
your local authorities, waste disposal service, or the shop where you purchased the
product.
Deutsch
Die Europäische Richtlinie 2012/19/EU verlangt, dass technische Ausrüstung, die
direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist,
nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das
Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere
elektrische und elektronische Geräte über die dafür zuständigen und von der
Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative
Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere
Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die
örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei
dem Sie das Produkt erworben haben.
Español
La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio
aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión debe separarse de los
residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad
suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través
de los puntos de recogida que ponen a su disposición el gobierno y las autoridades
locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo
a evitar posibles consecuencias negativas para el medio ambiente y la salud de las
personas. Si desea obtener información más detallada sobre la eliminación segura
de su aparato usado, consulte a las autoridades locales, al servicio de recogida
y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el
producto.
Français
La directive européenne 2012/19/UE exige que l’équipement sur lequel est apposé
ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures
ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter
ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens
de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de
lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et
la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de
traitement des déchets, ou l’endroit où vous avez acheté le produit.
Italiano
La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate
con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme
ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve
essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario
smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche
mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici
locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze
potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in
Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di
smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.
Declaration of Conformity
български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че този тип
радиосъоръжение SM-SP-40 е в съответствие с Директива 2014/53/ЕС. Цялостният
текст на ЕС декларацията за съответствие може да се намери на следния интернет
адрес:
www.ubnt.com/compliance
Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa
SM-SP-40 u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti
dostupan je na sljedećoj internetskoj adresi:
Čeština [Czech] Tímto UBIQUITI NETWORKS prohlašuje, že typ rádiového zařízení
SM-SP-40 je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k
dispozici na této internetové adrese:
Dansk [Danish] Hermed erklærer UBIQUITI NETWORKS, at radioudstyrstypen SM-SP-40 er
i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklæringens fulde
tekst kan findes på følgende internetadresse:
Nederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type
radioapparatuur SM-SP-40 conform is met Richtlijn 2014/53/EU. De volledige tekst van
de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:
www.ubnt.com/compliance
English
Hereby, UBIQUITI NETWORKS declares that the radio equipment type
in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.ubnt.com/compliance
Eesti keel [Estonian] Käesolevaga deklareerib UBIQUITI NETWORKS, et käesolev
raadioseadme tüüp SM-SP-40 vastab direktiivi 2014/53/EL nõuetele. ELi
vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil:
www.ubnt.com/compliance
Suomi [Finnish] UBIQUITI NETWORKS vakuuttaa, että radiolaitetyyppi SM-SP-40 on
direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen
teksti on saatavilla seuraavassa internetosoitteessa:
Français [French] Le soussigné, UBIQUITI NETWORKS, déclare que l’équipement
radioélectrique du type SM-SP-40 est conforme à la directive 2014/53/UE. Le texte
complet de la déclaration UE de conformité est disponible à l’adresse internet suivante:
www.ubnt.com/compliance
Deutsch [German] Hiermit erk lärt UBIQUITI NETWORKS, dass der Funkanlagentyp
SM-SP-40 der Richtlinie 2014/53/EU entspricht. Der vollständige Text der
EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:
www.ubnt.com/compliance
Ελληνικά [Greek] Με την παρούσα ο/η UBIQUITI NETWORKS, δηλώνει ότι ο
ραδιοεξοπλισμός SM-SP-40 πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της
δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:
www.ubnt.com/compliance
Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a SM-SP-40 típusú
rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelőségi nyilatkozat
teljes szövege elérhető a következő internetes címen:
Íslenska [Icelandic] Hér með lýsir UBIQUITI NETWORKS yfir því að SM-SP-40 er í samræmi
við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB
samræmisyfirlýsing er að finna á eftirfarandi netfangi:
Italiano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di
apparecchiatura radio SM-SP-40 èconforme alla direttiva 2014/53/UE. Il testo completo
della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet:
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
SM-SP-40
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
is
Latviešu valoda [Latvian] Ar šo UBIQUITI NET WORKS deklarē, ka radioiekārta SM-SP-40
atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā
interneta vietnē:
Lietuvių kalba [Lithuanian] Aš, UBIQUITI NET WORKS, patvirtinu, kad radijo įrenginių tipas
SM-SP-40 atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas
šiuo interneto adresu:
Malti [Maltese]
SM-SP-40
tiġi kkonsultata minn www.ubnt.com/compliance
Norsk [Norwegian]
samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den
fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse:
www.ubnt.com/compliance
Polski [Polish] UBIQUITI NETWORKS niniejszym oświadcza, że typ urządzenia radiowego
SM-SP-40 jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest
dostępny pod następującym adresem internetowym:
Português [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o
presente tipo de equipamento de rádio SM-SP-40 está em conformidade com a Diretiva
2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte
endereço de Internet:
Română [Romanian] Prin prezenta, UBIQUITI NET WORKS declară că tipul de
echipamente radio SM-SP-40 este în conformitate cu Directiva 2014/53/UE. Textul
integral al declarației UE de conformitate este disponibil la următoarea adresă internet:
www.ubnt.com/compliance
Slovenčina [Slovak]
SM-SP-40 je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii
na tejto internetovej adrese:
Slovenščina [Slovenian]
skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na
naslednjem spletnem naslovu: www.ubnt.com/compliance
Español [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo
radioeléctrico SM-SP-40 es conforme con la Directiva 2014/53/UE. El texto completo
de la declaración UE de conformidad está disponible en la dirección Internet siguiente:
www.ubnt.com/compliance
Svenska [Swedish] Härmed försäkrar UBIQUITI NETWORKS att denna typ av
radioutrustning SM-SP-40 överensstämmer med direktiv 2014/53/EU. Den fullständiga
texten till EU-försäkran om överensstämmelse finns på följande webbadress:
www.ubnt.com/compliance
www.ubnt.com/compliance
www.ubnt.com/compliance
B’dan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta’ tagħmir tar-radju
huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformità tista’
UBIQUITI NETWORKS erklærer herved at utstyret
www.ubnt.com/compliance
www.ubnt.com/compliance
UBIQUITI NETWORKS
www.ubnt.com/compliance
UBIQUITI NETWORKS potrjuje, da je tip radijske opreme
týmto vyhlasuje, že rádiové zariadenie typu
SM-SP-40
er i
SM-SP-40
www.ubnt.com
Ubiquiti Networks, Inc.
685 Third Avenue, 27th Floor
New York, NY 10017
USA
Support help.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com
©2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the
Ubiquiti U logo, the Ubiquiti beam logo, sunMAX, SolarPoint, TOUGHCable, and UNMS
are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States
and in other countries. All other trademarks are the property of their respective owners.
AJ092818
Loading...