Two Brothers Racing Monster 696 User Manual
Installation Instructions
V.A.L.E.
2009 Ducati
VARIABLE AXIS LOCKING EXHAUST
Monster 696
V.A.L.E.™ Dual Slip-on Exhaust System with M-2 Canisters
Part # 005-2490406DV, 005-2490407DV, 005-2490408DV
Parts List
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a centerstand
or ideally a service lift.
2. Remove mufer joint pipe springs.
TM
3. Remove mufer mounting bolts.
4. Remove left and right mufers.
6. Install left mufer using the OEM hardware and springs.
7. Install right mufer using the OEM hardware and springs.
8. Adjust mufer alignment.
9. Tighten the 8 X-Ring bolts.
10. Tighten mufer mounting bolts.
Qty. Description Part Number
2 Mufer Canister Varies
1 Slip-on Tube left 005-24904L
1 Slip-on Tube right 005-24904R
1 HARDWARE KIT 005-249-3
2 X-Ring Kit 005-7-2-3KIT
1 TBR Sticker Kit 015-10212
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualied motorcycle
technician. If you have any doubts as to your ability to install this performance
part, please consult with your local motorcycle dealer. Read all instructions rst
before starting installation. Make sure the motorcycle and exhaust system are
completely cool before starting the installation. Also, make sure the bike is secure
on a centerstand or ideally a service lift during installation. Be sure to save all stock
components for possible use later.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as
is” without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for
a particular purpose and disclaims all responsibility for consequential and incidental damages or any other losses
arising from the use of these products or parts.
5. Install TBR slip-on tubes to mufers by attaching the
X-Ring to the mufers using the 6x14mm socket head cap
screws and lock washers provided. Leave loose for now.
11. Double check all your work.
12. Before you run the bike, clean off all ngerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Also,
remove any plastic lm from the name badge(s) and or
canister clamp(s). Run the bike and enjoy. It is normal for
some white smoke to appear the rst time you start the
bike. This is packing/manufacturing oil from inside the
pipe burning off. Check for gaps or leaks. If you nd a leak,
a little high temperature silicon sealant should x it. After
50 to 100 miles, recheck all fasteners for tightness.
Continued on pg. 2
V.A.L.E.
2009 Ducati
VARIABLE AXIS LOCKING EXHAUST
Monster 696
V.A.L.E.™ Dual Slip-on Exhaust System with M-2 Canisters
Part # 005-2490406DV, 005-2490407DV, 005-2490408DV
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue
after a few heat cycles, this is a normal characteristic of high quality stainless steel.
Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft,
clean cloth.
TM
Titanium Header System: Polished titanium pipes will experience color shift ranging
from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright nish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the berglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon ber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the berglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon ber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters at the rst signs of packing material deterioration. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon ber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Qty. Description Part Number
2 Mufer Canister Varies
1 Slip-on Tube left 005-24904L
1 Slip-on Tube right 005-24904R
1 HARDWARE KIT 005-249-3
2 X-Ring Kit 005-7-2-3KIT
1 TBR Sticker Kit 015-10212
Loading...