Two Brothers Racing KFX50 User Manual

2007 Kawasaki
KFX50
Comple te Exha ust Sys tem wit h M-6 Caniste r Part # 0 05-169 0104M
Make sure the ATV is completely cool before starting
1. the installation. Make sure the ATV is secure with parking brake on.
Remove right side engine cover (black). Push pin in the
2. inside of holder and pull outside out.
Installation Instructions
Use a small amount of supplied high temp sealant
6. inside of muffler at pipe joint. Slide muffler into place and tighten to frame with 8x30mm Flange Bolt.
Re-install the right side engine cover.
7.
Before you run the bike, clean off all fingerprints and
8. dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 1 to 2 hours of riding recheck all fasteners for tightness.
Parts List
Qty. Description Part Number
1 M-6 Muffler Canister 005-169-204 1 SS Header Assembly 005-16901H 1 HARDWARE KIT 005-169-3 1 8x30mm Flange Bolt 005-FB830 1 8mm Flange Nut 005-FN8 1 Permatex High Temp Sealant 031-P22072 2 Two Brothers Racing Decals 015-10208-A
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualied
motorcycle technician. If you have any doubts as to your ability to install this performance part, please consult with your local motorcycle dealer. Read
all instructions rst before starting installation. Make sure the vehicle and exhaust system are completely cool before starting the installation. Also, make sure the vehicle is secure on a centerstand or ideally a service lift during installation. Be sure to save all stock components for possible use later.
Warranty
Two Brothe rs Racing p roducts are intended fo r closed co urse compet ition purpo ses only, and therefore are sold “a s is” without warranty. Two B rothers Rac ing specifi cally discla ims any war ranties of merchantabi lity or fit ness for a particular purpose and discla ims all res ponsibility for conseq uential and incidental damages or any other losses aris ing from the use of thes e products or parts.
Remove OEM exhaust pipe.
3.
Do not use the gasket between the header and
4. cylinder head. Make sure header pipe collar sits down
into recess before tightening header flange. (It may be easier to see by standing ATV up on rear bumper.
Use the supplied 8mm Flange Nut to secure head pipe
5. to mid-pipe bracket using OEM bolt.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal characteristic of high quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve. TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve. TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038 Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two Brothers Racing does not provide a warranty for burned canisters.
2007 Kawasaki
KFX50
Comple te Exha ust Sys tem wit h M-6 Caniste r Part # 0 05-169 0104M
005-1690104M
Qty. Description Part Number
1 M-6 Muffler Canister 005-169-204 1 SS Header Assembly 005-16901H 1 HARDWARE KIT 005-169-3 1 8x30mm Flange Bolt 005-FB830 1 8mm Flange Nut 005-FN8 1 Permatex High Temp Sealant 031-P22072 2 Two Brothers Racing Decals 015-10208-A
Loading...