Page 1
Installation Instructions
TM
2009-15 BMW
V.A.L.E.
V ARIAB L E A X I S L OCK I N G E X H A U S T
R1300S
Slip-O n Exhaust Sy stem
Part # 0 05-2650406V / 005-2650407V / 005-2650408V
Parts List
Qty. Description Part Number
1 Muffler Canister Varies
1 Muffler Canister Clamp Varies
1 Stainless Steel S-bend Tube 005-26504S
1 HARDWARE KIT 005-265-3
1 X-Ring Kit 005-7-2-3KIT
4 6x14mm Sock et Head Cap Screws 005-SH614
1 TBR Sticker Kit 015-10212
IMPORTANT - PLEASE READ CAREFULLY
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a centerstand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and theref ore are sold “as is”
without warr anty. Two Brothers Racing specifically disclaims any warranties of mer chantability or fitness f or a partic ular
purpose and disclaims all responsibility for consequential and incidental damag es or any other losses arising from the use
of thes e products or parts .
1. Make sure the bike is completely cool before starting
the installation. Make sure the bike is secure on a
centerstand or ideally a service lift.
2. Remove heat shield.
3. Loosen muffler joint clamp.
4. Remove muffler mounting bolt.
5. Install TBR slip-on tube to TBR muffler using the
supplied socket head cap screws, lockwashers and
X-Ring provided. Leave loose for now.
6. Slide rubber lined muffler clamp over TBR muffler.
7. Install TBR muffler assembly to motorcycle using the
OEM hardware. Leave loose for now.
8. Align muffler and tighten muffler joint clamp.
9. Tighten X-Ring bolts in a cross pattern.
10. Tighten muffler mounting strap.
11. Remove clip-nuts from OEM muffler assembly and
install on TBR slip-tube.
12. Re-install OEM heat shield.
13. Double check to make sure that all hardware is
tightened.Carefully double check your work to
insure that all hardware is securely fastened. If you
are using bags on motorcycle make sure you have
adaquate clearance between muffler and bags to
keep from causing damage, this is not covered
under w
arranty.
14. Before you run the bike, clean off all fingerprints
and dirt, as any oily residue will etch the metal and
become somewhat permanent when the system
gets hot. Also, remove any protective plastic
from the name badges on the muffler canister(s)
or the muffler clamp(s). Run the bike and enjoy.
It is normal for some white smoke to appear
the first time you start the bike. This is packing/
manufacturing oil fro
m inside the pipe burning
off. After 50 to 100 miles, recheck all fasteners for
tightness.
Page 2
V.A.L.E.
2009 BMW
V ARIAB L E A X I S L OCK I N G E X H A U S T
R1300S
Slip-O n Exhaust System
Part # 0 05-2650406V / 005-265 0407V / 00 5-2650408V
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place.
For cleaning use a mild spray cleaner. Always apply cleaner or
polish with a soft, clean cloth.
Stainless Header System: Polished stainless steel pipes will turn
a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel.
TM
Carbon Fiber Mufflers: Always make sure the fiberglass packing
inside is in good condition and not burned out, as exhaust heat
inside an empty canister will deteriorate the Carbon Fiber sleeve.
TBR sells repack kits (TBR part # 005-10038) that include new rivets and repack material as well as a drill bit (#30), making it easy
to do yourself. Also, NEVER dyno test your bik e with carbon fiber
mufflers installed - the intense heat and lack of cooling air can
quickly cause the CF material to burn. Two Brothers Racing does
not provide a warranty for
Aluminum Mufflers: Use an aluminum or mag wheel polish such
as Mother’s to restore the bright finish to factory spec.
burned carbon fiber.
Qty. Description Part Number
1 Muffler Canister Varies
1 Muffler Canister Clamp Varies
1 Stainless Steel S-bend Tube 005-26504S
1 HARDWARE KIT 005-265-3
1 X-Ring Kit 005-7-2-3KIT
4 6x14mm Sock et Head Cap Screws 005-SH614
1 TBR Sticker Kit 015-10212
Loading...