Turbo Air TGIM-23 Installation Manual

GLASS DOOR ICE MERCHANDISERS

Please read this manual completely before attempting to install or operate this equipment!

An asterisk(*) in a model number means the external finish of cabinet, black & white color, and each model is identical except the aesthetic difference which doesn't affect the performance.

Model No. :

TGIM-23* TGIM-49*

SIGN PANEL

DOOR ASSEMBLY

FRONT VIEW FRONT VIEW SIDE VIEW

SIGN PANEL

EVAPORATOR FAN

DOOR ASSEMBLY

DOOR

HANDLE

SHELF(F)

BOTTOM GRILLE

CONDENSER COIL

MOTOR BLADE

EVAPORATOR FAN MOTOR

CONDENSER FAN MOTOR

EVAPORATOR COIL

BACK SPACER

SHELF(U)

COMPRESSOR

CONTENTS

1. SPECIFICATIONS

PAGE

........................................................................................

2. SERIAL NUMBER

........................................................................................

3. NOTICE TO CUSTOMER / INSTALLATION ............................................... 3

4. CLEANING

5. BASIC OPERATION

6. BEFORE REQUESTING SERVICE

7. WARRANTY

...................................................................................................

.................................................................................

5~9

...........................................................

.........................................................................................

11~12

SPECIFICATIONS

GLASS DOOR ICE MERCHANDISERS

MODEL COMP H.P. Amp / watt V/Hz REFRIGERANT

CRATED WEIGHT

TGIM-23*1/3 6.5A / 820W(defrosting input) (110-120)V~ / 60Hz R-134a 376lbs

TGIM-49*

11.8A / 1160W(defrosting input) (110-120)V~ / 60Hz R-404A 587lbs

SERIAL NUMBER

The serial number can be found on the data label located inside the unit.

Please retain this serial number for service purposes.

Turbo air

NOTICE TO CUSTOMER

Loss or spoilage of products in your refrigerator/freezer is not covered by warranty. In addition to following recommended installation procedures, you must run the refrigerator/ freezer 24 hours prior to usage.

INSTALLATION

1. GOOD AIR CIRCULATION

- Please make sure to avoid any partition and object which may stop the air flow.

- Please make sure there is enough space for air circulation to the rear of the unit. Recommended space between the rear of the unit to the wall is at least 5 inches.

2. PLACE ABOVE STRONG FOUNDATION

- Please make sure that the floor where the unit will be placed can support the total weight plus any other contents that it may hold.

3. DO NOT PLACE NEAR HEAT

- Please make sure to avoid hot corners and locations near stoves.

- High ambient temperature will significantly reduce cooling efficiency.

4. INDOOR USAGE ONLY

- This unit is designed and tested for indoor use only.

- Outdoor usage will void its warranty.

5. STABILIZATION

- Turn leg levelers counter clockwise as necessary in order to properly level cooler.

6. LEVELING

- Please make sure that the unit levels from the front to the back and side to side.

7. Unit should be on dedicated outlet.

Turbo air

CLEANING

1. CLEANING STAINLESS STEEL INTERIOR AND EXTERIOR

: Damage to stainless steel finish due to improper use of cleaning products or

non- recommended products is NOT covered under this product's warranty.

• Do

- Use warm, soapy water and a soft, clean cloth or sponge.

- Rinse surfaces with clean, warm water and dry immediately to avoid water spots.

• DO NOT USE

- Abrasive or harsh cleaners

- Ammonia

- Chlorine bleach

- Concentrated detergents or solvents

- Metal or plastic-textured scouring pads

- Vinegar-based products

- Citrus-based cleaners

2. CLEANING THE CONDENSER FINS

- To maintain proper refrigeration performance, the condenser coil must be free of dust, dirt, and grease. This will require periodic cleaning. condenser fins should be cleaned at least every three months (90 days) or as needed.

3. CLEAN THE GASKET

- The door gasket should be cleaned frequently to maintain proper sealing.

4. CHECK AFTER CLEANING

- Check the unit again for safety.

- Check that the unit is operating properly.

CAUTION

1. POWER CORD

- Please make sure that the power cord is connected to the proper voltage.

- A protected circuit of the correct voltage and amperage must be run for connection of the line cord.

- Turn ‘off’ the power switch before disconnecting the power cord, whenever performing maintenance functions or cleaning the refrigerated cabinet.

- Compressor warranties are void if compressor burns out due to low voltage.

2. RE-STARTING

- If disconnected, wait for 5 minutes before re-starting.

Turbo air

+ 9 hidden pages