Wireless Tire Pressure and Temperature
Monitoring System Monochrome Display Manual
Wide Screen Monochrome Display
Model #: TST-507-D-M
Thank you for purchasing the TST Tire Pressure Monitoring System. With minimal care, your new TPMS will
provide reliable service for many years. Please read and understand the information contained within this manual.
Keep this manual for future reference.
Telephone: 770.889.9102
Website: www.tsttruck.com
Document #: TST-Doc-507 WSD-M Manual-(C)
TST-Doc-507 WSD-M Manual-(C)
INDEX
Page 1 - Display Features
Page 2 - Display Components and Controls
Pages 3 - 6 - Programming Sensor Codes Into the Display
-Automatic Code Learning (Option #1)
-Pressure Coding (Option #2)
-Manual Coding (Option #3)
Page 7 - Display Installation
Page 7 - Display Buttons
Page 8 - Parameter Settings (Pressure & Temperature)
Page 9 - High Temperature and High Pressure Settings
Page 10 - Low Pressure Alarm Settings
Page 11 - Restore Display Factory Parameters
Page 11 - Display Alerts - Out of Parameter/Fast Leaks
Page 12 - Display Alerts - Sensor Low Battery Alert
Page 13 - Other Functions
Pages 14 - 15 - Additional Functions
Page 16 - Troubleshooting Tips
Pages 16 - 19 - Common Questions
Page 19 - Display Specifications
TST-Doc-507 WSD-M Manual-(C)
DISPLAY FEATURES
1)Large, wide screen LCD display of pressure and temperature.
2)Options for Color or Monochrome screen.
3)Suction cup and cradle mount included.
4)Integrated lithium battery that is rechargeable.
5)Wake-up activation of monitor when in motion.
6)Automatic monitor illumination in dark conditions.
7)Programmable high and low pressure alarm thresholds.
8)Programmable high temperature alarm.
9)Visual and audible warning alarms when temperature or pressure exceeds thresholds.
10)Multiple pressure units: PSI, BAR.
11)Selectable temperature unit: °C or °F.
12)Program up to 110 tires.
13)Tire pressure and temperature is displayed simultaneously for quick viewing of each tire.
14)The trailer tires can be electronically removed from the screen when not towing.
15)The towing vehicle tires can be electronically removed from the screen when parked.
16)Push button programming.
17)A fully charged display will continuously operate 5-7 days on battery power.
18)Temperature and pressure settings are configured “per axle.”
1
TST-Doc-507 WSD-M Manual-(C)
DISPLAY COMPONENTS IN KIT
|
Power Adapter |
Monochrome Display |
Suction Cup Mount |
Cradle Mount
DISPLAY CONTROLS
Display Holder
GO
SET
BACK
PressureUnit:BARorPSI,user-selectabletemperatureunit:
C° or F°, user-selectable.
2
TST-Doc-507 WSD-M Manual-(C)
PROGRAMMING SENSOR CODES INTO THE DISPLAY
Note: Yoursensorswillbeginreadingassoonasthey are coded into the display. Once you go back to the main screen by pushing the “BACK” button twice, you may hear an alarm and see a pressure reading of “0”. Simply press the (+) button quickly to silence the alarm.
Note: It is recommended to label each sensor first with the provided numbering code stickers, similar to the following pattern, before you code the sensors. This allows you to know which sensor is programmed to which tire position. You can also write in your sensor number pattern.
Or use your own numbering pattern:
3
TST-Doc-507 WSD-M Manual-(C)
AUTOMATIC CODE LEARNING (option #1)
Note: CodeallthesensorstothedisplayBEFOREscrewing them onto the tire valve stem unless otherwise noted.
1.Push and hold the “SET” button until it beeps. You are now in the programming mode. The “HI PRESSURE SET” parameter will blink at the bottom of the screen. Push the (+) button and scroll through the parameters until “LEARN ID” appears.
2.Quickly press and release the “SET” button. The first tire onthedisplaywillblink.Ifyouwanttoprogramadifferent tire,pressthe(+)buttontomovetothecorrecttire.Push the “SET” button again and “FFF FFF” will flash. Put the sensor for that tire position next to the display and press the “GO” button. The display will capture the sensor code and show it on the screen. Again, push and release the“SET”buttontosavethecodetothatposition.When coded correctly, a single beep will be heard and a six (6) digit code will be shown.
3.Use the (+) button to move to the next tire position you want to program. Again, press the “SET” button and “FFF FFF” will blink. Put the sensor for that tire position next to the display and press the “GO” button to capture the sensor code. Press “SET” again to save.
4.When you are finished programming all of your sensors, press the “BACK” button to return to the parameter at the bottom of the screen. Use the (+) or (-) buttons to scroll to another parameter, if necessary. If finished programming, press the “BACK” button again to go to the Main Screen. (Your sensors will begin reading “0” pressure and will alarm. Press the (+) button to silence the alarm while you continue your set-up).
4
TST-Doc-507 WSD-M Manual-(C)
Note: To delete a single sensor code:
Press the “SET” button until it beeps (approx. 3 seconds). Push the (+) button and scroll through the parameters until “LEARN ID”appears.Pressandreleasethe“SET”button.Usethe(+)or(-) buttons to scroll to the tire you wish to remove. Press the “Set” button to select that tire. It will start flashing. Press the “Back” button for3seconds. Youwill hear3beeps. Thecodewill change to“FFFFFF”whichwillbeflashing.Press“SET”once.Theflashing will stop and the ID code will be deleted.
Note: To delete all of the tire codes:
Press the “BACK” button for 6 seconds. You will hear 6 beeps. “DEL ALL” will appear on the screen. Press “SET” once. You will hear one beep. “FFF FFF” will appear. All ID codes are deleted.
Note: When in the coding mode, the display will time-out within approximately one (1) minute if no buttons are pushed. At that point, you will have to start the coding process again.
Note: Be sure the sensor being coded is at least two feet away from the other sensors.
PRESSURE CODING (option #2)
1.Be sure your sensors are numbered. Screw the sensors partly onto each valve stem in the order you numbered them. Do NOT screw them down far enough to hear air hissing out.
2.Push the “SET” button until it beeps. You are now in the programming mode. The “HI PRESSURE SET” parameter willblinkatthebottomofthescreen.Pushthe(+)button and scroll through the parameters until “LEARN ID” appears.
3.Quickly press and release the “SET” button. The first tire on the display will blink. If you want to program a
5
TST-Doc-507 WSD-M Manual-(C)
different tire, press the (+) button to move to the correct tire.Pushthe“SET”buttonagainand“FFFFFF”willflash.
4.Tighten the sensor down on the corresponding tire valve stem. The ID code will display and flash.
5.TosavetheIDcodesetting.Press“SET”once.Itwillbeep and sensor code is saved.
6.To remove the ID code setting, Press “BACK” once. “FFF FFF” will re-appear. The setting will not be saved.
7.Press “BACK” twice to return to the main screen.
MANUAL CODING (option #3)
Note: This method is mainly used to program sensor codes from an old monitor to a new monitor if you do not have the sensors available.
1.Push the “SET” button until it beeps. You are now in the programming mode. The “HI PRESSURE SET” parameter willblinkatthebottomofthescreen.Pushthe(+)button andscrollthroughtheparametersuntil“SETID”appears.
2.Quickly press and release the “SET” button. The first tire onthedisplaywillblink.Ifyouwanttoprogramadifferent tire,pressthe(+)buttontomovetothecorrecttire.Push the“SET”buttonagainandthefirstdigitof“FFFFFF”will flash. Press the (+) button to select the correct number or letter. Press “GO” to move to the next position. Press the (+) button to change to the correct number or letter. Continue this procedure until all six digits are changed.
3.Press “SET” once to save the new codes. You will hear a beep and the code will stop flashing.
6
Loading...