T&S Brass B-0850 Installation Manual

Limited One Year Warranty

T&S warrants to the original purchaser (other
than for purposes of resale) that such product is
free from defects in material and workmanship
for a period of one (1) year from the date of
purchase. During this one-year warranty period,
if the product is found to be defective, T&S shall,
at its options, repair and/or replace it. To obtain
warranty service, products must be returned
to...

T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department

2 Saddleback Cove

Travelers Rest, SC 29690

Shipping, freight, insurance, and other
transportation charges of the product to T&S
and the return of repaired or replaced product
to the purchaser are the responsibility of the
purchaser. Repair and/or replacement shall be
made within a reasonable time after receipt by
T&S of the returned product. This warranty does
not cover Items which have received secondary
fi nishing or have been altered or modifi ed after
purchase, or for defects caused by physical
abuse to or misuse of the product, or shipment
of the products.
Any express warranty not provided herein, and
any remedy for Breach of Contract which might
arise, is hereby excluded and disclaimed. Any
implied warranties of merchantability or fi tness
for a particular purpose are limited to one year in
duration. Under no circumstances shall T&S be
liable for loss of use or any special consequential
costs, expenses or damages.
Some states do not allow limitations on how
long and implied warranty lasts or the exclusion
or limitation of incidental or consequential dam­ages, so the above limitations or exclusions may
not apply to you. Specifi c rights under this war-
ranty and other rights vary from state to state.

Installation and

Maintenance

Instructions

B-0850 & B-0865 and
B-2992 Series

LAVATORY FAUCETS

Deutsch: Installations- und
Wartungsanleitungen

Español: la Instalación y las

Instrucciones de
Mantenimiento

P/N: 098-003113-45 Rev.6
Date: 10-13-09
Drawn: TEH
Checked: JRM 10-28-09
Approved: JHB 10-28-09

Français: les Instructions

d’Installation et
d’Entretien

Exploded View

38

25

26

28

27

24

36

31

30

23

29

21

20

19

12

18

17

16

11

13

6

35

34

33

32

22

20

19

18

10

17

16

9

8

37

39

74

13

7

15

14

13

3

2

6

5

1

14

15

13

* Some items are listed for instructional purposes

and may not be sold as separate parts.

2

Part Number Guide

Faucet Assemblies

1 Asm, Rigid GN Swivel Yoke 8” CC 005973-40
2 Locknut, Yoke 000956-45
3 Washer, Swivel Yoke - Bottom 000993-45
4 Yoke, Swivel *
5 Washer, Yoke Star 000982-45
6 O-Ring, Knuckle Joint 001062-45
7 Nipple 000342-20
8 O-Ring, Swivel Yoke - Center 001068-45
9 Washer, Swivel Yoke - Top 000994-45
10 Washer, Shank 000999-45
11 Locknut 002954-45
12 Center Body 000136-40
13 Nut, Coupling 000958-20
14 Washer 000981-45
15 Washer, Beveled Sleeve 001091-45
16 Body, Faucet *
17 Locknut, Body Bottom 000960-20
18 Washer, Nipple 001006-45
19 Washer, Body 002290-45
20 Locknut, Body Top 000959-20
21 Asm, Eterna RH Spindle 006478-40
22 Asm, Eterna LH Spindle 006477-40

23 Escutcheon 001257-45

Handle Assemblies

24 Handle, Lever Zinc - Cold w/ Blue Index & Screw 001636-45
Handle, Lever Zinc - Hot w/ Red Index & Screw 001637-45
Handle, Lever Zinc - Blank w/ Screw 001638-45
25 Four Arm Handle 002521-45
26 Dome Handle - Cold 001784-40
Dome Handle - Hot 001783-40
27 Index, Button, Blue (Cold) 001660-45
Index, Button, Red (Hot) 001661-45
28 Screw, Lever Handle 000922-45
29 Handle, Wrist Action, 4” 000078-40
Handle, Wrist Action, 6” 000079-40
30 Screw, Handle 000925-45
31 Index, Snap-In, Blue (Cold) 001686-45
Index, Snap-In, Red (Hot) 001194-45

Nozzle Assemblies

32 Asm, Nozzle GN with Tip 120X
Asm, Nozzle GN with Rosespray *
33 Gooseneck Nozzle 000398-40
34 Rosespray B-0103
35 Washer, GN Tip 001043-45
36 Tip, Faucet 000861-25
37 Spout, 5” Cast (Shank & Aerator) 012602-40
38 Aerator B-0199-03

39 Shank *

3

[2.5cm Ø]

[3.5cm Ø]

[3.5cm Ø]

[20 to 30cm]

[10 to 15cm]

1” Ø

1-3/8 Ø

1-3/8 Ø

4” to 6”

8” to 12”

HOT

HOT & COLD CENTER SECTIONS

CAN BE AT ANGLE

THEN FAUCET WILL
FIT X WITH STD. 1/4”

IPS CROSS PIPES

FURNISHED

X

Y

SPOUT

IF Y IS

1/2”

8”

1”

7-3/4”

1-1/2”

7-3/8”

2”

7”

COLD

General Instructions

Installation:

1. Turn off water supply and drain
lines. Drill (3) three holes in sink
or countertop where you are install­ing faucet assembly. See illustration
below:

12

1

2

3. Install no.12 (shank) through the
center hole in sink or deck. Reinstall
no.10 and fi rst no.11 as shown:

12

10

11

9

6

greased

hand
tighten

4. Screw second no.11 (about half
way up shank) and slide no.9 and
no.6 (greased) up onto bottom of
no.12 shank.

Installation: (Nozzle)

Note: Nozzle should be installed
fi rst.

1. Apply Tefl on tape or pipe joint
compound to threaded end of
no.32/33.

2. Tighten no.32/33 fi rmly by hand
into no.12.

Center Body

2. Remove no.2 from no.12 by loos­ening with a wrench. Disassemble all
parts from no.1.

Hot / Cold Side Valves

5. Remove no.21/22, no.20, and
no.19 from no.16. (No.17 and
no.18 remain on no.16.)

15

4

14

21/22

20

19

18
17

16

13

General Instructions

6. Remove no.13, no.14 and no.15
from no.16. Assemble the previous
items onto arm of no.7, as shown in
illustration below. Both side valves.

16

13,14,15

7

7. Insert no.7 into no.16, loosely
tighten no.13 onto threads by hand.
Do this for both hot and cold valves.

7

4 (grooves
should face
downward)

13

Cold Side

16

Hot Side

4
(grooves should
face upward)

8. Insert no.16 up through underside
of sink or lavatory and fi t no.4 onto
no.12. (Make sure greased no.6 is in
place.)

9. Loosely tighten no.17 and no.18
against bottom of sink. Do this for

both sides.

16

18

17

12

6

4

10. Reinstall no.19 and no.20 onto
no.16 at top of sink. Loosely tighten
by hand. Do this for both sides.
(Make sure greased no.8 is in place.)

16

20

19

6

8

4

Final Assembly of Center Body
(No.12) Section:

11. Reinstall second no.6, no.3, no.5
and no.2 onto no.12. Make necessary
adjustments to allow proper position­ing of no.1.

1

3

2

10

9

13

2

11

12

12

6

5

.85 to .88

12. Tighten no.10 and (top) no.11
on underside of lavatory sink with a
wrench.

13. Tighten no.2 on bottom of no.12
with a wrench.

14. Tighten no.17 and no.18 on both
no.16’s underneath lavatory sink, also
tighten no.19 and no.20 on top side of
lavatory sink, with a wrench.

5