True TWC-24-OP, TWC-24-OPG, TUR-24-OPG, TBC-24-OP, TBC-24-OPG Use And Care Manual / Installation Instructions
...
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
USE AND CARE MANUAL / INSTALLATION INSTRUCTIONS
TWC, TBC, TUR Models (All overlay models - OP/OPG included)
WINE CABINETS, BEVERAGE CENTERS
AND UNDERCOUNTER REFRIGERATORS
www.true-residential.com
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
CONTENTS
UNCRATING INFORMATION / INSTALLATION MANUAL
Ownership 2
Safety Precautions 2
Disposal of Old Refrigerator 2
CFC Disposal 2
Uncrating 3
Cabinet Cleaning 3
How to Connect to Electricity 4
Leveling Refrigeration Equipment 4
Installing Anti-Tip Brackets 5
Overlay Models Only - OP/OPG 6-13
Installing True Signature Louver Grill 14-15
Start-up & Temperature Control 16
Shelving Operation 16-17
Drawer Divider Installation & Operation 17
General Maintenance 18
Replacement Parts 18
Installation Specifications
(TWC, TBC, & TUR Door Units) 19
Installation Specifications (TUR Drawer Units) 20
TUR Plan View 21
Tapper Unit Installation under counter tops 22
Installing Draft Standard and Hook Up 23-24
Pressure 25
Tapping 25
Draft Beer Problems 25
Changing CO
2 & Pressure Adjustment 26
Cleaning Instructions for Draft Towers 27
Troubleshooting 28
Frequently asked Questions 29
Stainless Steel Equipment Care and Cleaning 30
Warranty 31
Specifications are subject to change without notice.
1
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
OWNERSHIP
To ensure that your unit works properly from the first day, it
must be installed properly. We highly recommend a trained
refrigeration mechanic and electrician install your True unit.
The cost of a professional installation is money well spent.
Before you start to install your True unit, carefully inspect it for
freight damage. If damage is discovered, immediately file a
claim with the delivery freight carrier. True is not responsible
for damage incurred during shipment.
If you have any questions about the installation, please contact
your True dealer or True Technical Service Department at 1-800325-6152. Please have your model and serial number(s) available
when you call our Service Department.
SAFETY PRECAUTIONS
• This refrigerator must be properly installed and located in
accordance with the installation instructions before it is used.
• Do not allow children to climb, stand or hang on the shelves
in the refrigerator. They could damage the refrigerator and
seriously injure themselves.
PROPER DISPOSAL OF THE OLD
REFRIGERATOR
Child entrapment and suffocation are not problems of the past.
Junked or abandoned refrigerators are still dangerous, even if
they will sit for “just a few days”. If you are getting rid of your old
refrigerator, please follow the instructions below to help prevent
accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
CFC DISPOSAL
Your old refrigerator may have a cooling system that used CFC’s
(chlorouorocarbons). CFCs are believed to harm stratospheric
ozone. If you are throwing away your old refrigerator, make sure
the CFC refrigerant is removed for proper disposal by a qualified
service. If you intentionally release this CFC refrigerant, you can
be subject to fines and imprisonment under provisions of the
environment legislation.
• Do not store or use gasoline or other ammable vapors and
liquids in the vicinity of this or any other appliance.
• Keep hands away from the “pinch point” areas (gaps between
the doors and between the doors and cabinet). Small areas
are not necessarily safe.
• Unplug the refrigerator before cleaning and making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
• Setting temperature control to off removes power from the
condensing unit, it does not remove power from other circuits
(for example, interior lights).
• It is recommended to store the keys to the door lock away from
the cabinet to prevent accidental entrapment.
2
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
UNCRATING
Tools Required:
• Cutting utensil (utility knife)
• Hammer
• Crowbar
• Phillips head screwdriver
The following procedure is recommended for uncrating the unit:
A. Move your unit as close to the final location as possible before
removing the wooden skid.
B. Remove nails securing cardboard box to the wooden skid.
Then discard any outer packaging (cardboard, clear plastic).
(See images 1-3). Inspect for concealed damage. Again,
immediately file a claim with the freight carrier if there is damage.
IMPORTANT - Remove wooden block with Phillips head
screw driver before removing refrigerator from pallet.
C. Remove skid by carefully lifting the refrigerator off and place
skid aside. (See images 3-4).
D. Remove clear plastic coating from cabinet.
E. Open the unit and remove any packing material--styrofoam,
tape, and any other material used for shipping purposes. (See
images 5-7).
CABINET CLEANING
A. The exterior may be wiped clean with mild soap and water.
A good stainless cleaner is recommended on stainless steel
models.
CAUTION
Do not use any steel wool, abrasive or chlorine based products to
clean stainless steel surfaces.
B. The interior of the cooler should be cleaned periodically and
we recommend a mild solution of baking soda and water which
will help reduce any inherent odors. Do not use harsh cleaners
on any surface of the interior. For cleaning stainless steel see the
Stainless Steel Equipment Care and Cleaning section on page
30.
NOTE: Keys for coolers are provided at the time of sale.
Image 1.
Image 2. Remove nails securing
cardboard box to skid.
Image 3. Wood shipping block
protects door and door hinge.
Image 4. Move unit to its final
location before removing from
wooden skid.
Image 5.
Image 6.
Image 7.
3
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
HOW TO CONNECT TO
ELECTRICITY
Do not, under any circumstances, cut or remove the third
(ground) prong from the power cord. For personal safety, this
appliance must be properly grounded.
Before your new unit is connected to a power supply, check the
incoming voltage with a volt meter. If anything less than 100% of
the rated voltage for operation is noted, correct immediately.
The power cord of this appliance is equipped with a 3-prong
(grounding) plug which mates with a standard 3-prong
(grounding) wall outlet to minimize the possibility of electric shock
hazard from this appliance. A 115V AC, 60 Hz, 15 amp circuit
breaker and electrical supply are required.
Have the wall outlet and circuit checked by a qualified electrician
to make sure the outlet is properly grounded.
If the outlet is a standard 2-prong outlet, it is your personal
responsibility and obligation to have it replaced with the properly
grounded 3 prong wall outlet.
Do not use an extension cord or two prong adaptor. Electrical
ground is required on this appliance.
The refrigerator should always be plugged into its own individual
electrical outlet, which has a voltage rating that matches the
rating plate. This provides the best performance and also
prevents overloading house wiring circuits which could cause a
fire hazard from overheated wires. Never unplug your refrigerator
by pulling on the power cord. Always grip plug firmly and pull
straight out from the outlet.
LEVELING REFRIGERATION EQUIPMENT
A. Set unit in its final location. Be sure there is adequate
ventilation in your room.
B. Proper leveling of your True refrigerator is critical to operating
success (for non-mobile models). Effective condensate removal
and door operation will be effected by leveling. Adjust leg
levelers on the front or rear of the cabinet if the unit needs to be
lowered or raised.
C. The refrigerator should be leveled from the interior of the unit
front to back and side to side with a level. (See illustration 1). If
the refrigerator is not level, adjust the stainless steel leg levelers.
The leg levelers can be adjusted by turning to reach the desired
leveling height. (See image 1.)
D. Free plug and cord from back of refrigerator. Do not plug in.
E. The unit should be placed close enough to the electrical
supply so that extension cords are never used.
Warning
Compressor warranties are void if the unit is more than 7 ft.
(2.1m) from plug-in connection or if an extension cord is used.
Repair or replace immediately all power cords that have become
frayed or otherwise damaged. Do not use a cord that shows
cracks or abrasion damage along its length or at either end.
When moving the refrigerator away from the wall, be careful not
to roll over or damage the power cord.
Illustration 1.
Image 1. If the front of the cabinet needs to be lowered or
raised adjust the leg levelers.
4
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
INSTALLING ANTI-TIP BRACKETS
REQUIRED FOR STACKED AND DRAWER UNITS
Tip Over Hazard: A child or adult can tip the refrigerator and
may cause property or bodily harm. Connect anti-tip brackets
to the rear feet of the unit. Reconnect the anti-tip bracket if the
product is moved. Failure to follow these instruction can result
B C
in property or bodily harm.
Read all installation instructions first. Install the anti-tip brackets
to hold both rear legs of the stack combo or drawer refrigerator.
Follow these steps to secure the brackets to the oor before
moving the unit into final operating position.
Contact a qualied oor covering installer for the best procedure
of drilling mounting holes through your type of oor covering.
Before moving the unit, take precautions to protect the oor
covering.
938786
A
ANTI-TIP BRACKET KIT:
A - 2 Anti-tip brackets (937355)
B - 4 Masonary 3/16” screws (937357)
C - 4 Wood #12 - 2” screws (937356)
Determine the location of the unit. From the front of the
determined location of the lower louver grill measure back
21 3/4”. From the determined side of the unit measure over
13/16”. This is where the back and outer side of the bracket
should sit. Using the bracket as a template mark the holes
for drilling. (See illustration 1).
To mount the anti-tip bracket to a wood oor, drill pilot holes for
each of the bracket holes (4 total). To mount the anti-tip bracket
to concrete or ceramic oor use a masonry bit to drill pilot holes.
Align anti-tip bracket holes with the holes in the oor. Fasten
anti-tip bracket with screws provided using the brass colored
screw for wood, or blue colored masonry screw for concrete.
Move unit into final position making sure rear leveling legs slide
into the anti-tip brackets.
13
/16”
Bracket Locator
13
/16”
21
3
/4”
/4”
3
21
Grill (front)
Illustration 1.
5
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
INSTALLATION SPECIFICATIONS
These dimensions are for overlay (OP/OPG) models only!
WARNING:
Please go to page 19 for non-overlay dimensions before
installing any models.
True’s Wine Cabinets and Beverage Center are designed to be
inserted into a cabinet opening or free standing.
When installing the Wine Cabinet or Beverage Center into a rough
opening make sure there is a properly prepared opening for door
swing clearance and electrical placement. Flush mounted version
needs extra clearance on width opening.
ROUGH
OPENING
HEIGHT
Min 341/4" - Max 35"
ROUGH
OPENING
DEPTH
25"
ROUGH OPENING
WIDTH
1
/2"
24
1
/2" needed in back
of unit for plug.
2315/16"
TOP VIEW
*Flush mounted
version with extra
clearance on
width opening.
Front View of
refrigerator
between
cabinets.
*2417/32"
221/16"
SIDE VIEW
1
/4"
45˚ Opening
*Shown 45˚ angle
where door kicks out
and amount it extends
outside of the cabinet.
2315/16"
TOP VIEW
471/8"
34"335/32"
FRONT VIEW
291/2"
DOOR
HEIGHT
25
1
/16"
* Includes 3/4" cabinet panel -
33/8"
supplied by others.
Height Dimension +/- 1/2".
6
OVERLAY (OP/OPG) INSTALLATION
DRAWERED MODELS
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
ROUGH
OPENING
HEIGHT
Min 341/4” - Max 35”
Front View of
refrigerator
between
cabinets.
ROUGH
OPENING
DEPTH
25"
ROUGH OPENING
WIDTH
24"
1
/2" needed in back of
unit for plug.
Top View of refrigerator
between cabinets.
3
/4"
22 1/16"
SIDE VIEW
24 13/32"
34"
23 15/16"
FRONT VIEW
Height Dimension
+
/- 1/2".
14 1/2"
14 1/2"
4 7/16"
TOP VIEW
20 31/32"
1
43
/32"
7
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
OVERLAY (OP/OPG) INSTALLATION
INSTALLING OVERLAY MODELS FOR GLASS DOOR
& SOLID DOOR MODELS
Models
Solid Door Glass Door Drawered
TWC-24-OP TWC-24-OPG TUR-24D-OP
TUR-24-OP TUR-24-OPG
TBC-24-OP TBC-24-OPG
Cut Out Dimensions (WxDxH)
241/2" x 25" x 341/4" to 35" 241/2" x 25" x 341/4" to 35" 24" x 25" x 341/4" to 35"
*Height dimensions are minimum 333/4" to maximum 35".
2413/32"
1
22
/16"
34"
These dimensions are for overlay (OP/OPG) models only!
Please go to page 19 for non-overlay dimensions before
True’s Overlay Models are designed to be inserted into a
cabinet opening or free standing.
WARNING:
installing any models.
Solid Door Panel Dimensions
Door Panel Width 2313/16"
Door Panel Height 291/2"
Door Panel Depth
Door Panel Weight 10 lb. max
3
/4” max
Glass Door Panel Dimensions
Door Panel Width 2313/16"
Door Panel Height 291/2"
3
Door Panel Depth
Door Panel Weight 10 lb. max
Rail/Style Dimension 2" min
/4" max
Drawer Panel Dimensions
13
/16"
Drawer Panel Width
Drawer Panel Height 14
Drawer Panel Depth
Drawer Panel Weight 10 lb. max
23
1
3
/4" max
/2"
Height Dimension +/- 1/2".
8
29
1
/2"
2313/16"
13
/16"
17
6"
Back of overlay panel
.965"
(3 sides)
solid door
3
/4"
6"
.840"
14
3
/4"
23
1
/2"
29
1
/2"
2313/16"
13
/16"
17
6"
Back of overlay panel
.965"
(3 sides)
glass door
3
/4"
6"
.840"
14
3
/4"
23
1
/2"
OVERLAY (OP/OPG) INSTALLATION
INSTALLING OVERLAY MODELS FOR DRAWERED MODELS
.965"
(top, left, right)
27/8"
115/8"
14
1
/2"
WINE AND BEVERAGE CABINET USE AND CARE MANUAL
2413/32"
2321/32"
1
22
/16"
.965"
(top, left, right)
.840"
(bottom)
Back of overlay panel
6"
1713/16"
3
/4"
2313/16"
34"
drawers
Height Dimension +/- 1/2".
9
Loading...