Troybilt TB32CS, 41AC132C063 Owner’s Manual

perator's Manual

®

Electric Trimmer

Model TB32CS

0®

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

P/N 769-00428 Rev 2 (10/02)

PRINTED IN USA

Content Page

Calling Customer Support .................................................... 2

Rules for Safe Operation ..................................................... 3

4now Your Unit ....................................................... 6

Assembly Instructions ....................................................... 7

Operating Instructions ....................................................... 8

Maintenance and Repair Instructions .......................................... 11

Cleaning and Storage ....................................................... 13

Accessories and Replacement Parts ........................................... 13

Troubleshooting Chart ...................................................... 14

Specifications .......................................................... 15

Warranty Information ....................................................... 16

Parts List .................................................... Inside Back Cover

This operator's manual is an important part of your new trimmer. It will help you assemble, prepare and maintain the unit
for best perforrnance, please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the equipment and copy the
information from it in the space provided below. ]-his information is very important i[ you need help from oUt Customer
Support Department or an authorized dealer.

• You can locate the model number Onthe unit. A sample model plate is explained below. For future reference,
please copy the model number and the serial number of the equipment in the space below.

Serial Humber Model!Parent Part Humber

Copy the model / parent part

number here:

Ser.No:

Illllllllllllllllllllllllllllllllllllllllllllllllllcopyt.eserio,numberhere:

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of

this unit, please ca!! the Custome r Support Department.

Ca1!,1.(330)-558-7220 or 1.(866)-840-6483 to reach a Customer Support representative. Please have your

_7"_ unit s model number and serial number ready when you call. See previous Section to locate this information.

you will be asked to enter the Serial number in order to process your call.

2

The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention

and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper
accident prevention measures.

SYMBOL MEANING ]

DANGER: Failure to Obey a safety warning I

will result in serious injury to yourself or to I
others. Always follow th e safety precautions I
to reduce the risk Of fire, e ectr c shock and

personal injury. J

I SYMBOL MEANING ]

A SAFETY ALERT SYMBOL: Indicates danger,

Aiik warning or caution. Attention is required in

order to avoid serious personal injury. May be

used in conjunction with other symbols or
p ctographs.

NOTE: Advises you of information or instructions Vital

to the operation or maintenance of the
equipment.

READ ALL INSTRUCTIONS

DANGER: When using electric gardening

appliances, basic safety precautions should
always be followed to reduce the risk of fire,

electric shock and personal injury. Carefully
read and understand the entire operators

manual before using your trimmer. Pay close
attention to the operating instructions and
safety warnings.

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.

• Inspect the unit before use. Replace damaged parts.

Make sure all fasteners are in place and secure.
Replace cutting attachment parts that are cracked,

chipped or damaged in any way. Make sure the
cutting attachment is properly installed and securely
fastened. Be sure the cutting attachment shield is

properly attached, and positioned as recommended.
Failure to do so can result in personal injury to the

operator and bystanders, as well as damage to the

unit.

• Use only 0.080 inch (2.03 mm) diameter genuine
factory parts replacement line. Never use metal-

reinforced line, wire or rope. These can break off and
become dangerous projectiles.

• Be aware of the risk of injury to the head, hands and feet.

I ,#IL IWARNING: Failure toobeya safety warning l

,_IL |can result in injury to yourself and others. I

|Always follow the safety precautions to |
| reduce the risk of fire, electric shock and

| personal injury. |

CAUTION: Failure to obey a Safety warning
may result in property damage or personal
injury to yourself or to others. Always follow I

the safety precautions to reduce the risk of
fre, electric shock and persona njury. J

Clear the area to be cut before each use. Remove all
objects such as rocks, broken glass, nails, wire or

string. They can be thrown or become entangled in the
cutting attachment. Clear the area of children,

bystanders, and pets. At a minimum, keep all children,
bystanders and pets outside a 50-foot (15 m.) radius;

there still may be a risk to bystanders from thrown
objects. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the motor
and cutting attachment immediately.

This unit was not designed to be used as a
brushcutter. Do not attach or operate this unit with any

type of brushcutting blade or brushcutting attachment.

ELECTRICAL SAFETY WARNINGS

• Since the tool is double-insulated, a 2-wire extension
cord (an extension cord without a ground) may be

used. A 3-wire extension cord (an extension cord with
a ground) that uses a NEMA type connector (parallel

blade, U ground) is recommended. Extension cords
are available from your local retailer. Use only round-

jacketed extension cords approved for outdoor use.

WARNING: To reduce the risk of electrical I

shock, use only SW-A, SOW-A, STW-A, I
STOW-A, SJW-A, SJQW-A, SJTW-W or

SJTOW-A cord types. ]

• This tool is double-insulated. Use only identical
replacement parts when servicing. Repair or replace

damaged cords.
To reduce the risk of electrical shock, this unit has a

polarized plug (one blade is wider than the other). This
unit will fit with apolarized plug in one way only. If the
plug does not fit fully into the unit, reverse the plug. If

it still does not fit, use a cord with the correct
connection. Do not modify the unit in any way.

3

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR

120 VOLT APPLIANCES USING 0-6 AMPS

cord length (ft.) 25 50 100 150

Wire size (AWG) 16 16 16 i4

• CORD SETS: Make sure your cord set is in good

condition, with a cord that is heavy enough to carry
the current that your unit will draw. An undersized cord

set will cause a drop in line voltage resulting in a loss

of power, as well as overheating. The table shown

above illustrates the correct size to use depending on
the cord length and nameplate amperage rating. If in
doubt, use the next heavier size line gauge. The

smaller the gauge number, the heavier the cord. To

prevent the cord from disconnecting from the unit, use
the cord hook shown in the Operating Instructions.

• Do not abuse the power cord. Do not pull or carry the
unit by the cord, use the cord as a handle, close a

door on the cord, or pull the cord around sharp edges
or corners. Keep the cord away from heated surfaces,
oil and sharp edges.

• Ground Fault Circuit Interrupter (GFCl) protection
should be provided on the circuit(s) or outlet(s) that will

be used for the unit. Use receptacles with built-in
GFCl protection for an extra measure of safety.

• A nameplate on your unit indicates the voltage used.
Never connect the unit to an AC voltage that differs

from this voltage.

• Inspect all extension cords and the unit power

connection periodically. Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Repair or replace the cords if

any defects appear.

• Avoid dangerous environments. Never operate your unit
in damp or wet conditions. Moisture is a shock hazard.

• Do not use the unit in the rain.

• Do not handle the plug or the unit with wet hands.

WHILE OPERATING

• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards. Also wear

ear/hearing protection when operating this unit. Wear

a face or dust mask if the operation is dusty. Long
sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not

wear loose clothtng, jewelry, short pants, sandals or
go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming/ines extended, and the proper line
installed. Do not extend the trimming line beyond the
length of the shield.

• Adjust the D-handle to your size to provide the best grip.

• Be sure the cutting attachment is not in contact with
anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Do not carry around a unit
that is plugged in with your finger on the trigger switch.

Be sure the switch is in the off position when plugging

in the unit.

• Use the right tool. Only use this tool for the purpose
intended.

• Do not overreach. Always keep proper footing and
balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on all handles or grips.

• Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it is rotating.

• Do not operate the motor faster than the speed needed
to cut, tnm or edge. Do not run the motor at high

speed when you are not cutting.

• Always stop the motor when cutting is delayed or
when walking from one cutting location to another.

• If you strike or become entangled with a foreign object,
stop the motor immediately and check for damage. Do
not operate before repairing damage. Do not operate
the unit with loose or damaged parts.

• Stop and switch the unit to off and unplug it during
matntenance, repair or cutting attachment

replacement.

• Use only genuine factory replacement parts when
servicing this unit. These parts are available from your

authorized service dealer. Do not use unauthorized
parts, accessories or attachments. Using unauthorized

parts may lead to serious injury, damage to the unit
and a voided warranty.

• Keep the unit clean of vegetation and other materials.
They may become lodged between the cutting
attachment and shield.

OTHER SAFETY WARNINGS

• Disconnect the unit from the power supply when it is idle,
when you are storing or transporting it, when you are

servicing it, and when you are changing attachments.

• Store the unit in a dry area, locked up to prevent
unauthorized use or damage, and stored in a high
place out of the reach of children.

• Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use. See the Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

4

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING SYMBOL MEANING

• THROWN OBJECTS AND
ROTATING CUTTER CAN

Indicates danger, warning or caution. //._

• SAFETY ALERT SYMBOL _/_

May be used in conjunction with other //

symbols or pictographs.

• WARNING - READ

OPERATOR'S MANUAL

CAUSE SEVERE INJURY

WARNING: Do not operate without

the cutting attachment shield in place.
Keep away from the rotating cutting

attachment.

©

{_ • WEAR EYE AND HEARING

Read the operator's manual(s) and follow

all warnings and safety instructions.

Failureto do so can result in serious injury

to the operator and/or bystanders.

PROTECTION

WARNING: Thrown objectsand loud

noise can cause severe eye injury and
hearing loss. Wear eye protection

meeting ANSI Z87.1 standards and ear
protection when operating this unit.

Use a full face shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders,
especially children and pets, at least

50 feet (15 m) from the operating area.

• SPEED SWITCH

Indicates "HIGH" or "FASTEST"
speed.

• SPEED SWITCH

Indicates "LOW" or "SLOWEST"
speed.

• SHARP BLADE

WARNING: Sharp blade on cutting

attachment shield. To prevent serious
injury, do not touch line cutting blade.

5

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Decorative trimming around trees, fences, etc.

Other optional accessories may be used with the
TB32CS. Refer to Operating the EZ-Link System for a list

of add-ons.

Shoulder Strap Clip _

D-Handle

Motor Housing

Plug

HousingG_

\

Two Speed

Switch

Shaft Housing

Hi

LO

Switch Trigger

Cutting Attachment

Shield

Line Cutting Blade

Cutting Attachment

6