Triumph Adler FAX 525 User Manual

Page 1

Page 2

English

Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer.

This product complies with the requirements of the Council Directives 89/336/EEC (EMC), 73/23/EEC (LVD) and 1999/5/EC (R&TTE), as amended where applicable, on the approximation of the laws of the member states relating to Electromagnetic Compatibility, Low Voltage and Radio & Telecommunications Terminal Equipment.

Page 3

Table of contents

English

Table of contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Notes, cautions and warnings

Chapter 1 - Introduction

Features Product options

Component identification

Control panel keys and indicators

Signal tones

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MFP option kit ISDN

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Components

One touch keypad

Dialling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Selecting functions and programming

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Chapter 2 - Installation

Getting started

Where to install your fax machine Unpacking Setting up

Installing paper trays and stackers

Installing the toner cartridge

Connecting a telephone line

Connecting a telephone, handset or answering machine

Connecting the power cable Loading paper Setting the clock Setting answering mode

Answering mode options

Changing answering mode Fax machine identification

Setting fax machine identification Setting language Connecting to a PBX MFP function

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . . . . 13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

. . . . . . . . . . . . . . . . . . . . . . . .16

. . . . . . . . . . . . . . . . . . . . . . . .18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

. . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

. . . . . . . . . . . . . . . . . . . . . . . .29

iii

Page 4

English

Chapter 3 - Dial Directories

Programming One Touch keys Chain dialling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Programming Auto Dial numbers Programming groups

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Chapter 4 - Basic Operations

Preparing documents

Document size

Multiple page documents Loading documents Sending fax to a single location

Search key dialling

Real-time dialling

Redialling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Confirming results

Stopping a transmission Receiving faxes manually Receiving faxes in memory

Memory reception

No paper reception

No toner reception

Cancelling messages stored in memory Rejecting unsolicited fax messages Power failures and memory Making copies

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Making copies using manual paper feeder Using voice request

Initiating voice request

Answering voice request

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

. . . . . . . . . . . . . . . . . . . . . . . . . . 39

. . . . . . . . . . . . . . . . . . . . 46

. . . . . . . . . . . . . . . . . . . . . . . . . . 46

. . . . . . . . . . . . . . . . . . 48

Chapter 5 - Advanced Operations

Sending faxes to multiple locations and/or groups Delayed sending of faxes

Sending delayed faxes to single locations

Sending delayed faxes to groups and/or multiple individual

locations

Cancelling delayed transmission Confidential faxes

Sending confidential faxes

Receiving confidential faxes

Creating confidential mailbox

. . . . . . . . . . . . . . . . . . . . . .50

. . . . . . . . . . . . . . . 50

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

. . . . . . . . . . . . . . . . . . . 53

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

. . . . . . . . . . . . . . . . . . . . . . . . . . 57

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Page 5

English

Closing confidential mailbox

Changing mailbox password

Printing confidential faxes Relay broadcasting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Relay initiating station

Relay key station

Relay broadcast report

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Initiating relay broadcast Polling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Polling transmission

Polling reception

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Cancelling polling transmission

Standard one-time/bulletin polling ITU bulletin polling

Printing bulletin messages Dual access

While sending faxes

While receiving faxes

While making copies

While printing reports

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

. . . . . . . . . . . . . . . . . . . . . . . . . . 67

. . . . . . . . . . . . . . . . . . . . .67

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Chapter 6 - Programming

Customising features and operations

Viewing your current settings

User function settings

User function settings list Changing user function settings Setting distinctive ring

Personal mailboxes

Creating personal mailbox (polling) Closing personal mailbox (polling)

Forward number programming Memory password

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Creating a memory password Changing a memory password Deleting a memory password

Restricted Access

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Creating a restricted ID password Changing a restricted ID Closing a Restricted ID

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

. . . . . . . . . . . . . . . . . . . . . . . . . 70

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

. . . . . . . . . . . . . . . . . . . . . . . . . . 78

. . . . . . . . . . . . . . . . . . . . . . .79

. . . . . . . . . . . . . . . . . . . . . . . .80

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

. . . . . . . . . . . . . . . . . . . . . . . . . . . 82

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

. . . . . . . . . . . . . . . . . . . . . . . . .83

Page 6

English

Dial Parameter Settings

Dial parameter settings list Changing dial parameter settings

Chapter 7 - Reports

Understanding reports

Activity report Broadcast confirmation report Active memory files report Telephone directory Configuration report Message confirmation report Confidential reception report Broadcast entry report Power outage report Protocol dump

Printing reports

Printing message confirmation report Printing other reports

Codes used in reports

Result codes Communication codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

. . . . . . . . . . . . . . . . . . . . . . . . . 86

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

. . . . . . . . . . . . . . . . . . . . . .91

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

Chapter 8 - Problem Solving

Clearing document jams Clearing printing paper jams Replacing the toner cartridge Replacing the image drum unit Reading print counters Shipping the fax machine Problem checklist

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Display panel messages

Normal display Error messages

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

Appendix A - Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . 93

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

. . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Appendix B - ISDN G4 Option

Specifications ISDN programming flow

Term definitions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113

. . . . . . . . . . . . . . . . . . . . . . . . .112

Page 7

English

Other settings

ISDN dial mode (user setting 30)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

. . . . . . . . . . . . . . . . . . . . . . . .113

ISDN dial mode (communication parameter) Speech receive (user setting 31) Other related functions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Display message examples

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

. . . . . . . . . . . . . . . . . . . . . . . . .114

Appendix C - MFP PC Interface Kit

Index

MFP option kit

As a PC printer: As a PC Scanner: PC Fax Modem

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117

. . . . . . . . . . . . . . . 114

. . . . . . . . . . . . . . . . . . . 116

vii

Page 8

English

Notes, cautions and warnings

Note: A note appears in this manual like this. A note provides

additional information to supplement the main text which may help you to use and understand the product.

CAUTION:

A caution appears in this manual like this. A caution provides additional information which, if ignored, may result in equipment malfunction or damage.

WARNING

A WARNING APPEARS IN THIS MANUAL LIKE THIS. A WARNING

PROVIDES ADDITIONAL INFORMATION WHICH, IF IGNORED,

MAY RESULT IN A RISK OF PERSONAL INJURY.

viii

Page 9

Chapter 1 - Introduction

This fax machine uses advanced Light Emitting Diode technology to transfer received and copied images to plain paper. It is designed to make the sending and receiving of faxes a fast and trouble free process.

Features

The fax machine includes the following features:

• 10 One Touch keys for automatic, single-key dialling of preprogrammed telephone numbers.

• 100 AUTO DIAL numbers for automatic dialling of additional preprogrammed telephone numbers.

English

• 10 Groups can be programmed to allow you to transmit a document to multiple locations with a single selection.

• A search feature to allow you to look for preprogrammed telephone numbers by name.

• Halftone transmission in up to 64 shades of grey.

• Fax communication at up to 33 600 bits per second.

• Automatic redial and page re-transmission when a telephone number is busy or when problems occur in communication.

• Advanced transmission and reception features, including delayed transmissions, transmission to multiple locations, confidential transmission and reception, relay broadcast initiate and polling.

• Advanced memory transmission and reception features, including automatic reception into memory with or without password printing.

• Reports to help you keep track of the operations and settings of your fax machine.

• Automatic power save mode.

• Answering modes for manual and automatic fax reception, automatic switching between incoming voice and fax messages and allows an answering machine to be connected in series to the telephone line after the fax machine.

Chapter 1 - Introduction 1

Page 10

English

• A closed network feature to allow you to limit who can send faxes to your fax machine, or to limit both where faxes can be sent to and received from.

• Your fax machine can also make 50 copies of an original document using standard weight (80 gsm) paper.

• 4 MB of built-in memory.

• During transmissions, your fax machine will begin scanning data into memory as it begins dialling (Instant Dialling), thus saving time since it does not wait for a connection on the receiving end.

• Advanced dual access feature allowing you to load and prepare documents for transmission while your fax machine is sending or receiving another message.

• High speed scanning of original documents.

• Restricted operation of your fax machine by using a four digit password.

Product options

MFP option kit

This option allows your fax machine to communicate with a computer. See Appendix C for more information.

ISDN

This option allows your fax machine to send and receive digital communications. See Appendix B for more information.

Chapter 1 - Introduction 2

Page 11

Component identification

Your new fax machine package should contain the following items:

1. Fax machine main unit

2. Document tray

3. Paper tray/copy stacker

4. AC power cable

5. Telephone line cable

6. Document stacker

7. Image drum unit (inside main unit)

8. Toner cartridge

9. User’s Guide (this manual) CD

English

10. Safety/Installation Instructions (not illustrated)

If anything appears missing or damaged, please contact your supplier as soon as possible.

Chapter 1 - Introduction 3

Page 12

Components

English

1. Paper tray/copy stacker - Load up to 100 sheets of paper into this

tray. Up to 30 sheets of received faxes or finished copies are stacked on top of this tray.

2. Document tray - Holds original documents that are to be faxed or

copied.

3. Document guides - Adjust these guides to the page width of the

documents that are to be faxed or copied.

4. One-Touch keypad

5. Manual paper feeder - Load paper into this slot when you want to

use a type of paper different from the paper in the paper tray.

6. Document stacker - Supports documents that have been faxed or

copied.

7. Control panel

Chapter 1 - Introduction 4

Page 13

English

8. PC Connector - Connect the computer cable into this connector.

9. LINE terminal - Terminal for connecting the unit to a telephone

line.

10. TEL terminal - Terminal for connecting the fax machine to an

external telephone or answering machine.

Note: Only one terminal is available and when the ISDN option is

installed voice communication is not supported.

11. Power switch

12. AC power inlet - Connect the AC power cable, supplied with your

fax machine, into this inlet.

Chapter 1 - Introduction 5

Page 14

English

13. LED print head - This black bar is the part of your fax machine

which writes received or copied images onto the image drum unit. You should clean this bar each time you change your toner cartridge.

14. Toner cartridge - This black cylinder, installed inside the image

drum unit, contains the black powder which is the ink for your fax machine. You will need to install a new toner cartridge when the REPLACE TONER CART message appears on the display.

15. Image drum unit - The image drum unit contains the green

photosensitive drum which receives images from the LED print head and transfers them to the printing paper. You will need to install a new drum unit when the REPLACE DRUM CART message appears on the display.

Chapter 1 - Introduction 6

Page 15

Control panel keys and indicators

1. LCD panel: Refer to this liquid crystal display (LCD) panel for

instructions and information while your fax machine is operating or while you are programming your fax machine.

English

2. Transmit resolution/

YES key: This key changes the resolution

used for transmitting documents. Use STD for standard originals, FINE and EX.FINE for detailed or small print originals, and PHOTO for originals that include colours or many shades of grey. You will also use this key as the

YES key when making

selections or to move your cursor while programming.

3. Type of original/NO

key: This key selects document contrast

after loading a document for transmission. Use LIGHT for originals that are too light, NORMAL for documents with good contrast, and DARK for originals that are too dark. You will also use this key as the NO

key when making selections or to move your cursor

while programming.

4. Auto Rec key: This key sets the answering mode of your fax

machine. The answering mode controls how your fax machine answers incoming calls and receives faxes. The display of your fax machine always indicates your current selection. See Setting the Answering Mode in Installation for more information about the answering modes available in your fax machine.

5. Email key: This key allows you to perform the email function. See

Appendix D for more information

Chapter 1 - Introduction 7

Page 16

English

6. Search key: The One Touch keys and Auto Dial numbers can be

programmed to have a name or location ID associated with their telephone numbers. Using this key by itself or in combination with the numeric keypad, you can search for these numbers alphabetically. You can also use the Search key to search for unassigned One Touch keys and Auto Dial numbers.

7. Hook/V. Request key: During a fax communication, pressing this

key tells the operator at the other fax machine that you want to talk at the end of your transmission or after reception of any page has been completed. To use this feature both fax machines must have an external telephone connected. To answer a voice request, press this key after lifting your telephone handset. When no fax communication is taking place, pressing this key opens the telephone line for manual dialling (not available in some countries). You will hear the dialling tone through the speaker of your fax machine.

Note 1: With the ISDN option installed, pressing this key for manual

dialling is not possible. Nor will a dialling tone be heard when this key is pressed.

Note 2: With the ISDN option installed, voice communication is not

supported.

8. Redial key: Pressing this key manually redials the last number

dialled on your fax machine.

Note: If your fax machine has been set to enter power save mode

(after the fax machine has been inactive for three minutes), the manual redial function does not work.

Chapter 1 - Introduction 8

Page 17

English

9. Auto Dial key: Auto Dial numbers are abbreviated numbers for

rapid dialling. Rather than dialling the entire telephone number, you can enter a 2-digit code to Auto Dial number instead. You can also use the Location IDs (names) associated with Auto Dial numbers to search for these locations by name using the Search key. This key is also used in combination with the #/Group Key to select preprogrammed groups when sending faxes to multiple locations.

10. Select Function key: Using this key activates the advanced

transmission and reception functions of your fax machine to obtain reports and for programming. To select a function, press the Select Function key, then press the One Touch key labelled with the function you want to use. While programming or selecting other functions, pressing the Select Function key a second time takes you directly back to the stand-by mode of your fax machine.

11. Copy key: After loading a document, press this key to make a copy.

When no documents are loaded, press this key once to obtain a Message Confirmation Report about your last transmission on the LCD Display Panel and a second time to receive a printed report. You can also use the Copy key as a short-cut for programming One Touch keys and Auto Dial numbers. After you have loaded a document and manually dialled a telephone number, press Copy so you can instantly program that number into an unassigned One Touch Key or Auto Dial number.

Chapter 1 - Introduction 9

Page 18

English

12. Stop key: This key cancels any operation currently in progress and

turns off the Alarm indicator. After loading paper, press this key to cancel alarm conditions after the condition has been corrected. During programming, pressing the Stop key takes you back step-bystep through the programming functions you have already selected.

13. Start key: Pressing the Start key initiates the operation indicated on

the display or confirms information you have entered into the display. While the fax machine is in power save mode, press the Start key to exit power save mode.

14. Alarm indicator: This indicator glows red and an alarm sounds

notifies you of any problem that occurs. To turn the alarm indicator off, press the Stop key and correct the problem.

15. Plus (+) key (One Touch key 8): Each fax number you enter or

program into your fax machine can be up to 32 digits long. When a number is longer than 32 digits, it is possible to dial this number using combinations of One Touch keys, Auto Dial numbers or the numeric keypad. When programming a chain dial number into a One Touch key or Auto Dial number, press the Plus key at the end of the first part of the number to indicate to the fax machine that this is a chain dial number. When programming TSI/CSI and call back numbers into your fax machine, this key is used to enter a “+” symbol.

Note: With the ISDN option installed, chain dial numbers can be

programmed but cannot be used.

Chapter 1 - Introduction 10

Page 19

English

16. Pause key (One Touch key 7): Use this key on the One Touch

keypad to enter automatic three second pauses in dialling when programming telephone numbers. For example, you may want to use this key to tell your fax machine to wait for an outside or international line to open. Pauses in telephone numbers are marked by a “P” symbol.

17. Space key (One Touch key 5): Use this key on the One Touch

keypad to enter spaces while programming or to erase previously programmed information. Unlike the Pause key, spaces are used for easier reading only and have no effect on dialling.

18. One Touch keypad: For a description of all the functions of the

One Touch keypad, see the following section “One Touch keypad”.

19. One Touch labels: After programming a location into a One Touch

key, write the name of the location on the One Touch label. Lift off the plastic cover and use a pencil to write in the name, then replace the cover.

20. #/Group key: Once you have programmed some One Touch keys

or Auto Dial numbers, use this key to create groups to allow you to send the same fax to multiple locations. After you have loaded a document, press the Auto Dial key and use this key to select the group you want to send your fax to.

Chapter 1 - Introduction 11

Page 20

English

21. 0/Unique key: When dialling, use this key to enter a “0”. When

programming your Sender ID or a Location ID, you can use this key to enter a variety of unique characters, e.g. ! # & ’ ( ) * + , - . / : ; = ?

· ä ß ñ ö ü Æ Å Ø æ å ø

22. Numeric keypad: When dialling, these twelve keys work like the

keypad on a telephone. You will also use the keypad to enter numbers, letters and other characters while programming. After pressing the Search key, you can also use the numeric keypad to alphabetically search for the names of locations programmed into your fax machine.

23. Ton e k ey: If your fax machine is set to pulse dialling, this key

allows you to switch the dialling operation of your fax machine from pulse to tone dialling during your current call. You can also use this key while programming to create numbers with mixed pulse-then-tone operation.

Note: This function is not available in some countries.

24. Caps key (One Touch key 1): In “Character string” input, when

CAPS is showing on the display, pressing this key allows you to execute a case shift.

25. Delete key (One Touch key 6): In “Character string” and “Numeric

string” input, pressing this key will delete the character indicated by the cursor.

Chapter 1 - Introduction 12

Page 21

One touch keypad

The One Touch keys are an important tool on your fax machine. You will use them for quick, one-touch dialling, and to access the functions and programming options of your fax machine.

Dialling

To use a One Touch key for dialling, press the appropriate One Touch key. For each key, you can program up to two telephone numbers: a primary number, which will always be dialled first, and an alternate number, which will be automatically dialled if the first number is busy or if there is no answer. You can also use the Location IDs (names) associated with One Touch keys to search for these locations by name using the Search key.

Selecting functions and programming

English

You will also use One Touch keys for selecting special transmission and reception functions, obtaining reports and programming. To select a function from the One Touch keypad, press the Select Function key, then press the corresponding One Touch key.

1/Delayed TX key: Using this key sends a fax at a later time and date, which you can specify for up to three days later.

2/Print Operation key: Using this key prints out a confidential received document stored in the memory of your confidential personal box number after entering your 4-digit password. If memory reception mode is set on your fax machine, use this key to print faxes that have been received in memory. Also, use this key to print any bulletin polling messages that have been stored in memory.

Note: Changing the answering mode of your fax machine

automatically prints out any non-confidential faxes that have been received into memory.

Chapter 1 - Introduction 13

Page 22

English

3/Confidential TX key: Using this key sends a confidential document to a personal mailbox (a memory storage area) in the receiving fax machine.

4/Relay Initiate TX key: Using this key sets up a relayed fax transmission. During a relayed fax transmission, your fax machine initiates the transmission by sending a document to a second fax machine, which then broadcasts the message to a number of other fax machines.

5/Polling key: Using this key sets your fax machine to scan and store documents in memory, then wait for another fax machine to call and request a document to be sent (polling transmission). When no document is loaded on the document table, using this key calls another fax machine and requests it to send the documents it has loaded into memory (polling reception).

6/Report Print key: Using this key manually prints reports from your fax machine.

7/Counter Display key: Your fax machine keeps track of the number of pages it has printed and scanned. Using this key checks the print and scan counters of your fax machine and resets the drum counter of your fax machine after replacing the image drum unit.

8/Location Program key: Using this key programs One Touch keys, Auto Dial numbers and groups into your fax machine.

9/User Program key: Using this key allows you to program identification information of your fax machine; set the clock of your fax machine; set up mail boxes for confidential message reception; change your fax machine function settings and dial parameters; program passwords for printing messages stored in memory; program forwarding number and, if fitted, ISDN parameters and to restrict the use of your fax machine.

10/Printer Cleaning key: Using this key prints a cleaning page for clearing any accumulated toner from the image drum of your fax machine.

Signal tones

Your fax machine emits a number of sounds to inform you of specific conditions.

Key Select Tone: This is a short beep that occurs each time you press a key.

Error Tones: If you press a wrong or inappropriate key, your fax machine will emit three short beeps. If your fax machine experiences a

Chapter 1 - Introduction 14

Page 23

English

problem during communications, it will emit three long beeps. Press the Stop key to turn the error tone off, then print a Message Confirmation Report to check the source of the problem by pressing the Copy key twice with no documents loaded.

Voice Request Tone: During a fax session, either you or the person at the remote fax machine can initiate a voice request. When the person at the remote fax machine either initiates or answers your voice request, your fax machine emits a repetitive warbling sound.

End of Session Tone: At the end of every successful fax session, your fax machine emits a short beep to inform you that there were no errors or problems in the communication.

Off-Hook Alarm Tone: If your fax machine is equipped with a handset and if the handset is left off the hook, your fax machine will emit an intermittent warbling sound. To turn off the sound, hang up the handset or press the Stop key.

Chapter 1 - Introduction 15

Page 24

Chapter 2 - Installation

Getting started

To install your new fax machine, follow the instructions from “Unpacking” to “Setting the Fax Identification”. You must complete these steps for your fax machine to operate properly.

If you have purchased an option package for your fax machine, refer to the documentation you received with that option.

Where to install your fax machine

1. Install your fax machine in a dust-free location away from direct

sunlight.

English

2. Allow several centimetres on each side of the fax machine to ensure

adequate ventilation.

3. Make sure that both power and telephone outlets are available

nearby.

4. Choose a location where the relative humidity is between 20% and

80%, and where the temperature is between 10 °C and 32 °C.

Chapter 2 - Installation 16

Page 25

Unpacking

Before you begin, make sure that all items listed below are included in your package. Remove the contents from the carton placing them on a sturdy surface.

English

1. Fax machine unit

2. Toner cartridge

3. Image drum unit (inside facsimile unit)

4. Power cable

5. Telephone line cable

6. Paper tray/Copy stacker

7. Document tray

8. Document stacker

9. This User's Guide (CD)

Note: A telephone handset, handset cradle and handset cable may also

be included. If any items are missing, notify your supplier immediately for a replacement. Keep your packing materials and carton in case you ever need to ship or transport the machine.

CAUTION:

Do not ship the fax machine with the image drum unit and toner cartridge installed. Refer to Shipping the Fax Machine later in this user’s guide.

Chapter 2 - Installation 17

Page 26

Setting up

Installing paper trays and stackers

1. Slot the tabs of the paper tray/copy stacker into the rearmost slots in

the top of the fax machine until the tabs lock into place.

2. Insert the document tray into the long horizontal slot on the top of

the unit until it locks into place.

English

3. Slot the tabs of the document stacker into the slots at the front of the

fax machine until the tabs lock into place.

Chapter 2 - Installation 18

Page 27

Installing the toner cartridge

1. Open the top cover.

2. Grasp the control panel. Pull upward and toward you until the

control panel releases, then swing it out of the way.

English

3. Carefully remove the protective sheet from the document feeder.

CAUTION:

Never expose the image drum unit to light for more than 5 minutes. Never expose the image drum unit to direct sunlight. Always hold the image drum unit by the ends. Never touch the surface of the green drum inside the image drum unit.

4. Lift the image drum unit out and keeping the image drum unit out of

direct sunlight. DO NOT touch the green surface of the drum.

Chapter 2 - Installation 19

Page 28

English

5. Carefully remove the protective sheet from the image drum unit.

6. Place the image drum unit back into your fax machine. Ensure that

the tabs on both sides of the image drum are inserted correctly as shown. Then press down firmly on both ends of the image drum until it snaps into place.

7. Remove the protective plastic cover from the toner well in the

image drum unit.

WARNING

BE CAREFUL WHEN HANDLING THE TONER CARTRIDGE. DO

NOT LET TONER SPILL ONTO YOUR CLOTHING OR OTHER

POROUS MATERIALS. IF YOU EXPERIENCE ANY PROBLEMS

WITH TONER, REFER TO THE SAFETY INSTRUCTIONS AT THE

BEGINNING OF THIS USER'S GUIDE.

Chapter 2 - Installation 20

Page 29

English

8. Remove the toner cartridge from its package and gently shake it

from side to side to distribute the toner. Then carefully peel the white plastic tape from the bottom of the toner cartridge.

CAUTION:

Be careful not to insert the toner cartridge backwards into the image drum unit.

9. With the ridged sides facing up and the coloured lever on your right,

insert the toner cartridge into the image drum unit. Slide the left end of the cartridge in first, then lower the right end into place.

10. Once the toner cartridge is in place, push the coloured lever all the

way forward to secure it and release the toner.

Chapter 2 - Installation 21

Page 30

English

11. Close the top cover of the fax machine until it snaps into place.

12. Close the control panel by pressing down until the cover snaps into

place.

Connecting a telephone line

1. Insert one end of the telephone cable into the LINE terminal at the

back of the machine.

2. Insert the other end of the telephone cable into your wall telephone

socket.

Note: Now, you can connect either an external telephone, the external

handset option or an answering machine to your fax machine. See the instructions below.

Chapter 2 - Installation 22

Page 31

Connecting a telephone, handset or answering machine

1. Insert one end of the telephone cable into the TEL1 terminal on the

back of the fax machine.

2. Insert the other end of the telephone cable into the socket in your

telephone, handset or answering machine.

Note 1: To connect both an answering machine and a telephone, first

connect your answering machine to your fax machine and then insert your telephone’s cable into the telephone socket on your answering machine.

English

Note 2: You will need to have the TAD mode feature turned on for an

answering machine to work with your fax machine. See Setting the Answering Mode later in this user’s guide.

Note 3: When the ISDN option is installed, an external telephone or

answering machine cannot be connected because voice communication is not supported on this fax machine when using ISDN.

Connecting the power cable

CAUTION:

Before connecting power, ensure that the power switch is OFF (“0” is in depressed position)

1. Insert the power cable into the power inlet socket located on the

back of the fax machine.

Chapter 2 - Installation 23

Page 32

2. Connect the unattached end of the power cable into an earthed AC

power outlet.

3. Switch your fax machine on using the power switch. The time and

current answering mode will appear on the display. Your fax machine is now in stand-by mode, ready to send or receive faxes.

Loading paper

Your fax machine can hold up to 100 sheets of standard weight (80 gsm) paper. For best results, use paper specially made for laser printers or photocopiers.

Your fax machine automatically reduces the vertical length of the page images it receives to fit on the paper loaded in your fax machine (down to 75% of the original length). For example, if a document created originally on legal-size paper is received, your fax machine reduces the received pages to fit on A4 or letter-size paper.

English

Note: Your fax machine is set at the factory to use A4 paper. If you

intend to use a different paper size, change the PAPER SIZE user function setting to match your new paper size. See Programming later in this user’s guide for instructions.

1. Adjust the right paper guide to the width size of your paper.

2. Remove the paper from its wrapper (up to 100 sheets). Note the

“print side” notice printed on the label. Fan the paper.

CAUTION:

Be sure to grasp the paper tightly to avoid slipping of the uppermost sheet of paper.

Chapter 2 - Installation 24

Page 33

3. Insert sheets of paper into the paper tray, print side down.

Note: When loading paper, it is recommended to insert more than ten

sheets of paper into the paper tray to prevent a “no-feed” response from the fax machine.

4. Adjust the left paper guide so that it is aligned to the paper width.

Setting the clock

Follow these instructions to set the time and date on your fax machine.

English

1. Press the Select Function key.

2. Press the 9/User Program One Touch key.

3. On the numeric keypad, press 3. The display will show 3:CLOCK

ADJUSTMENT.

4. Press the

and time.

5. Using the numeric keypad, enter the new date and time.

6. Press the

7. Press the Select Function key to finish.

YES key. The display will show the currently set date

YES key to confirm your entry.

Setting answering mode

Your fax machine has a number of answering modes which determine how it handles incoming calls (both fax and voice). The current answering mode appears on your fax machine’s stand-by display.

Note: When the ISDN option is fitted, Manual Receive Mode (TEL),

Telephone/Fax Auto Switch Mode (T/F) and Telephone Answering Device Mode (TAD) cannot be used because voice communication is not supported on this fax machine when using ISDN.

Chapter 2 - Installation 25

Page 34

Answering mode options

The answering mode which is best for you will vary depending on how you use your fax machine and what external telephone devices are connected to it. Read through the answering modes listed here, then follow the instructions below.

Auto Receive Mode [FAX]: If your fax machine is connected to a telephone line reserved only for fax communications, use the Auto Receive mode. Your fax machine will assume all incoming calls are fax messages and automatically receive all incoming fax messages.

Manual Receive Mode [TEL]: If you use the same line for both fax and telephone calls and the majority of your incoming calls are telephone calls, then the TEL answering mode is your best choice. Each time someone calls, your fax machine rings like a telephone. You can answer from either an external handset or from an external telephone connected to your fax machine. If you pick up the handset and hear fax machine tones (normally a short peep every three seconds), press the Start key to receive the fax. If you do not answer the phone and someone tries to send you a fax message, your machine will not accept it.

English

Note: Some older types of fax machines do not send CNG (calling)

tones and the line may be silent when you answer a call in TEL answering mode.

If you answer a call using a telephone connected to the same telephone line, but not connected directly to your fax machine, you can remotely tell your fax machine to start fax reception by entering a two digit remote receive number using the telephone keypad. See Remote Receive in Programming later in this user’s guide.

Telephone/Fax Auto Switch Mode [T/F]: When incoming calls are a mixture of fax and telephone calls, your best choice is the Telephone/Fax Auto SW mode. In this mode, your fax machine detects whether the incoming call is a fax or voice call. When the call is from another fax machine, your machine will switch to fax mode and receive the message. When the call is a voice call, your fax machine will ring like a telephone. If you do not answer, your fax machine will switch back to fax mode to allow the calling party to manually send a fax.

Note 1: Only use this mode if the telephone is located close to your fax

machine. After the initial ring, the telephone falls silent, but the fax machine continues ringing.

Chapter 2 - Installation 26

Page 35

English

Note 2: If the telephone is connected in parallel with the fax machine, the

fax machine cannot detect that the telephone has been picked up and will start auto reception while your conversation is in progress.

Telephone Answering Device Mode [TAD]: Use this mode if you have connected an answering machine to your fax machine. When a call is received and is not answered, your answering machine activates and is ready to send out your recorded outgoing message. At the same time, your fax machine monitors the incoming call to check if the call is a fax or voice call. If the incoming call is a fax call, your fax machine will receive the fax and no voice message will be recorded on your answering machine. If the incoming call is a voice call, then your fax machine will not activate and the calling party will be able to leave a voice message on your answering machine.

Note: In some countries, the Telephone Answering Device mode is

normally turned off. To have it turned on, contact your supplier.

Memory Reception Mode [MEM]: Use this answering mode if you want incoming faxes to be stored in the memoryD-0.0cTD-0.0019( )6(iy)-5.6(rr)-4.4( )6(iax)-5.6(e)6(machi-5.6(ene )nd no t]TJT*-0.0011 Tc0.1917 Tw[(nimmediael)-5(2(sy p-4.8(d)1.19i)-5.2(sn1.12te:d. Y-4.4(du )-6(wannt)-5.82h)1(2(edn)]TJ14.6724 0 TD-0.0021 Tc0.1016 Tw[(yue thie Ping )-6(aOpertion ifuncion i-6(tho]TJ-14.4724 01.1976 TD-0.0009 Tc0.0381 Tw[(nping )ut))ndymessage theathave)been ]TJ15.6329 0 TD-[ )-6(rto)rd in the memoryD To hprevet)]TJ-14.6329 01.1976 TD-0.0008 Tc0.27389Tw[(ansy data eceive)d fromrbeng fping]TJ14.676050 TD-0.001 Tc-.273 Tw[(yed ahile )our fax machine ws

Chapter 2 - Installation 27

Page 36

Changing answering mode

Follow these instructions to change the answering mode of your fax machine.

1. Press the Auto Rec key. Your fax machine displays your current

answering mode.

2. Press the Auto Rec key again. Your fax machine switches to the

next answering mode.

3. Continue pressing the Auto Rec key until the answering mode you

want appears on the display. After a short pause, your fax machine programs the new answering mode and returns to stand-by mode displaying the new answering mode setting.

Note: If a password has been set in the Memory Reception mode, you

will need to enter the password in order to disable the Memory Reception mode.

English

Fax machine identification

Fax machines use the information you will enter here to identify themselves during communications. In most countries programming this information into your fax machine is a legal requirement. The information you will enter here includes:

TSI/CSI: This is the telephone number of your fax machine. This number appears on displays and reports of other fax machines you are communicating with. This number may also be printed at the top of faxes you send to other fax machines.

Sender ID: This is a descriptive title and is usually the location of your fax machine or the name of your company or office. The Sender ID is printed at the top of every fax you send. You can enter up to 32 characters. The first 16 characters of your Sender ID is also used as your Personal ID, which may appear on displays or reports of other fax machines you are communicating with.

Note: Some fax machines do not print your TSI/CSI on their received

pages. To make sure that your TSI/CSI is always printed, you can include your fax number as part of your Sender ID.

Call Back Number: The Call Back Number is a telephone number (not a fax number) which the operator of the remote machine can use to reach you. If you use the voice request function while you are transmitting to

Chapter 2 - Installation 28

Page 37

another fax machine and no one is there to answer, your fax machine will automatically send a cover letter with a call back message. The call back message is printed on a separate sheet with the message “Please call back” and a telephone number where you can be reached. The call back number entered here is the number that appears on the call back message.

Setting fax machine identification

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. On the numeric keypad, press 4. The display shows 4:SYSTEM

DATA PRG.

English

4. Press the

YES key. The display shows NO=<TSI/CSI>,

ID=<SENDER ID>.

5. After the display clears, enter the full telephone number of your fax

machine using the numeric keypad up to twenty characters.

Note: Use the Location Prog or 8/+ One Touch key to enter a “+”

character before the number, which is a generally recognised method of indicating the international access code before the country dialling code. The 9/Space One Touch key is used to enter spaces in a number.

6. Press the Start key to save your entry.

7. Enter your Sender ID. This is a descriptive title up to 32 characters

long. Refer to the instructions below.

To do this Use

Enter numbers Numeric keypad. Press once for each number required. Enter spaces Space One Touch key Enter hyphens Hyphen One Touch key Enter alphabetic

characters

Enter a unique character

Move the cursor to make corrections

Chapter 2 - Installation 29

Locate the character you want on the numeric keypad. Press that key repeatedly until the character appears.

Press the 0/Unique key repeatedly until the character you want appears. The following characters are available: ! # & ’ ( ) * + , - . / : ; = ? · ä ß ñ ö ü Æ Å Ø æ å ø

Press

YES or X NO keys.

Page 38

8. Press the Start key to save your entry. The display shows

NO=<CALL BACK NO.>.

9. After the display clears, use the numeric keypad to enter the

telephone number you want to use for call back messages. Enter up to 20 characters.

Note: Use the Location Prog or 8/+ One Touch key to enter a “+”

10. Press the Start key to save your entry.

11. Press the Select Function key to finish.

Setting language

English

Your fax machine comes with multiple languages installed, which appear on the display and in reports. Follow the instructions below to switch languages.

Note: Your supplier may be able to provide you with additional

languages.

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

YES key. The display shows FUNCTION NO. [ ].

3. Press the

4. Using the numeric keypad, enter 14. This display shows 14:USER

LANGUAGE [****] YES (

) NO (X).

Note: [****] indicates which language your fax machine is already

using.

key to switch to the other installed language.

5. Press the NO

6. To accept the language change, press the

W YES key.

7. Press the Select Function key to finish.

Chapter 2 - Installation 30

Page 39

English

Connecting to a PBX

A PBX (Private Branch Exchange) is a private telephone system used to route internal calls. If you have to dial a prefix (access) number to get an outside line, then your line is connected to a PBX.

If you are connecting your fax machine to a PBX, follow the instructions below. These setting changes allow your fax machine to identify your PBX’s outside line dial prefix digits in the numbers that you program or dial in your fax machine. After it dials the prefix digits, your fax machine will wait until it sees that an outside line is available before dialling the rest of the number.

CAUTION:

In some countries you may require service assistance to make these changes. Also, some PBX installations may require additional adjustments to your fax machine. If you continue to have difficulty with fax communication after following these steps, contact your supplier.

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. On the numeric keypad, press 2. The display shows 2:DIAL

PARAMETER.

4. Press the

YES (

5. Press the NO

) NO (X)

(

6. Press the

YES (

7. Press the NO

YES key until the display shows PBX LINE [OFF]

) NO (X)

key. The display changes to PBX LINE [ON] YES

YES key until the display shows DIAL PREFIX [OFF]

) NO (X)

key. The display changes to DIAL PREFIX [ ]

ENTER 4DIGITS.

8. Using the numeric keypad, enter the number you normally dial from

your PBX to obtain an outside line. If the number is less than 4 digits, press the 9/Space key repeatedly until the display changes.

9. Press the

10. Press the Select Function key to finish.

Chapter 2 - Installation 31

YES key.

Page 40

Note 1: The Dial Prefix number for your PBX line must be included in all

outside telephone numbers you program into your fax machine or dial with the numeric keypad.

Note 2: To later turn off the PBX line and Dial Prefix functions, follow

Steps 1-7 above. At Step 8, press the 9/Space key four times, then continue with Steps 9-10.

MFP function

To use your fax machine as a PC printer/fax/scanner, you will need to install optional Multi-Function Peripheral (MFP) software into your computer. A PC connector and PC interface board may be included in your fax machine as standard equipment. For details on how to install the hardware and software necessary to use your fax machine as an MFP, please refer to the documentation that comes with the MFP software.

English

Chapter 2 - Installation 32

Page 41

Chapter 3 - Dial Directories

Programming One Touch keys

Your fax machine has ten One Touch keys for rapid dialling. You can store up to two fax numbers with 32 digits for each One Touch key, a main number and an alternate number. The alternate number is used if the main number is busy or does not answer. You can also enter a 15-character Location ID (name) for each One Touch key.

Note 1: To find One Touch keys which are not yet programmed, you may

repeatedly press the Search key during step 2.

Note 2: If all your One Touch keys are programmed, searching

automatically looks for the first unassigned Auto Dial number.

English

1. Press the Select Function key, then press the 8/Location Program

One Touch key. The display shows LOCATION PROGRAMMING ENTER (SRCH, OT, A/D, #)

2. Press a One Touch key to program and the display briefly shows

NO=<FAX NO.>, ID=<LOCATION ID> or a previously programmed fax number and location ID.

3. After the display clears, enter the main fax number as follows:

To do this Use

Enter numbers Numeric keypad (press once). Enter spaces Space One Touch key Enter hyphens Hyphen One Touch key

Enter pauses

Switch from pulse to tone dialling for part of the call

Move the cursor to make corrections

Pause key (i.e. to wait for long distance or outside lines)

*/Tone key

Press

YES or X NO keys.

4. Press the Start key.

Chapter 3 - Dial Directories 33

Page 42

English

5. Enter the Location ID. This is a descriptive title up to 15 characters

long. Refer to the instructions below.

To do this Use

Enter numbers Numeric keypad (press once). Enter spaces Space One Touch key

Enter alphabetic characters

Enter a unique character

Enter two characters using the same key

Move the cursor to make corrections

Locate the character you want on the numeric keypad. Press that key repeatedly until the character appears.

Press the 0/Unique key repeatedly until the character you want appears. The following characters are available: ! # & ’ ( ) * + , - . / : ; = ? · ä ß ñ ö ü Æ Å Ø æ å ø

Press the NO

Press

YES or X NO keys.

key to move to the next character.

6. Press the Start key. The display shows NO=<OR LOCATION>.

7. Enter the alternate fax number. Refer to the instructions following

Step 3.

8. The display shows G3 COMMUN. SPEED [33.6]. Press the NO

key to adjust the speed and the

YES key to select it.

Note: If you are experiencing problems communicating with a remote

location, try lowering the FAX SPEED or turning on ECHO PROTECTION.

9. The display shows G3 ECHO PROTECTION [OFF]. Press the

key to change the setting and the

YES key to select it.

Note: If the ISDN option is installed, the display will show ISDN DIAL

MODE (G4). Press the for this One Touch key or press the NO dial mode and then press the

10. After pressing the

YES key, the display automatically shows

YES key to select G4 as the dial mode

key to change to G3

YES key to select it.

LOCATION PROGRAMMING ENTER (SRCH, OT, A/D, #)

11. To continue programming One Touch keys, go back to Step 2. If

you are finished programming, press the Select Function key.

12. Lift off the plastic cover above the One Touch label. Using a pencil,

write in the name for your newly programmed One Touch key and replace the cover.

Chapter 3 - Dial Directories 34

Page 43

Note: If you want to delete any programming for a One touch key,

follow steps 1 - 2 and at step 3, press the 9/Space key until the number is deleted, then press the Start key and continue with Step 11.

Chain dialling

Each fax number that you enter or program into your fax machine can be up to 32 digits long. If you need to dial a number which is longer than 32 digits, then you can use the chain dial feature.

To create a chain dial number, program the first 31 digits of the number into a One Touch key or Auto Dial number. Then press the 8/+ One Touch key to make this a chain dial number. Next, program the rest of the number into another One Touch key or Auto Dial number. You can, if so desired, leave the second part of the number unprogrammed and enter it manually on the numeric keypad.

English

To use a chain dial number, select the One Touch key or Auto Dial number programmed with the first part of the chain dial number. The display will show PRESS OT/AD/SRCH KEY. Then select the One Touch key or Auto Dial number programmed with the second part of the chain dial number. If the second part of the chain dial number was not programmed, enter it manually on the numeric keypad. Press the Start key to begin sending the fax.

Note: When the ISDN option is fitted, chain dial numbers can be

programmed but cannot be used.

Programming Auto Dial numbers

Your fax machine has 100 Auto Dial numbers available for quick, 3-digit selection and dialling. For each Auto Dial number, you can enter a fax number up to 32 digits long and a Location ID (name) up to 15 characters long.

Note: To find Auto Dial numbers which are not yet programmed, you

may repeatedly press the Search key during step 2.

1. Press the Select Function key, then press the 8/Location Program

One Touch key. The display shows LOCATION PROGRAMMING ENTER (SRCH, OT, A/D, #)

2. Press the Auto Dial key.

Chapter 3 - Dial Directories 35

Page 44

3. Using the numeric keypad, enter a 3 digit number (001-100) for the

Auto Dial number you want to program.

4. The display briefly shows NO=<FAX NO.>, ID=<LOCATION ID>

or a previously programmed fax number and location ID.

5. Enter the fax number. Refer to the instructions below.

To do this Use

Enter numbers Numeric keypad (press once). Enter spaces Space One Touch key

English

Enter pauses

Switch from pulse to tone dialling for part of the call

Move the cursor to make corrections

Pause key (i.e. to wait for long distance or outside lines)

*/Tone key

Press

YES or X NO keys.

6. Press the Start key.

7. Enter the Location ID. This is a descriptive title up to 15 characters

long. Refer to the instructions below.

To do this Use

Enter numbers Numeric keypad (press once). Enter spaces Space One Touch key

Enter alphabetic characters

Enter a unique character

Locate the character you want on the numeric keypad. Press that key repeatedly until the character appears.

Press the 0/Unique key repeatedly until the character you want appears. The following characters are available: ! # & ’ ( ) * + , - . / : ; = ? · ä ß ñ ö ü Æ Å Ø æ å ø

Enter two characters using the same key

Move the cursor to make corrections

8. The display shows G3 COMMUN. SPEED [33.6]. Press the NO

key to adjust the speed and the

Note: If you are experiencing problems communicating with a remote

location, try lowering the FAX SPEED or turning on ECHO PROTECTION.

9. The display shows G3 ECHO PROTECTION [OFF]. Press the NO

X key to change the setting and W

Chapter 3 - Dial Directories 36

Press the NO

Press

YES or X NO keys.

key to move to the next character.

YES key to select it.

Page 45

Note: If the ISDN option is installed, the display will show ISDN DIAL

MODE (G4). Press the for this One Touch key or press NO mode and then press the

10. After pressing the

YES key to select G4 as the dial mode

key to change to G3 dial

YES key to select it.

YES key, the display automatically shows

LOCATION PROGRAMMING ENTER (SRCH, OT, A/D, #)

11. To continue programming AUTO DIAL numbers, go back to Step

3. If you are finished programming, press the Select Function key.

Note: If you want to delete any programming for an Auto Dial number,

follow Steps 1 - 4. At Step 5, press the 9/Space key until the number is deleted, then press the Start key and continue with Step 11.

Programming groups

English

Once you have programmed some One Touch keys or Auto Dial numbers, you can then program these numbers into groups to allow you to send the same fax to multiple locations. You can program up to 10 groups using a maximum of 80 numbers for all 10 groups into your fax machine.

1. Press the Select Function key, then press the 8/Location Program

One Touch key. The display shows LOCATION PROGRAMMING ENTER (SRCH, OT, A/D, #)

2. On the numeric keypad, press the # key. The display shows GROUP

SETTING [ ] ENTER 1-10

3. Using the numeric keypad, enter the group number (1-10) you want

to program.

4. The display shows the number of your current group and SELECT

LOC.(S) YES (STR/LOC.) EXIT (

). You can now add a location

to your group (or delete a location from it). Refer to the instructions below.

To do this Use

Add a One Touch location Press the One Touch key. Press Start to add it to the group.

Add an Auto Dial location

Delete a One Touch location

Chapter 3 - Dial Directories 37

Press Auto Dial. Enter a 3 digit Auto Dial number. Press Start to add it to the group.

Press the One Touch key. Press Start to delete it from the group.

Page 46

To do this Use

English

Delete an Auto Dial location

Search for a location by name to add or delete

Press Auto Dial. Enter a 3 digit Auto Dial number. Press Start to delete it from the group.

Press the Search key repeatedly until the location you want appears.Press Start to add it to the group. Press Start to delete it from the group.

5. After you have completed your selection (by pressing the Start

key), the display again shows SELECT LOC.(S) YES (STR/LOC.) EXIT (

). Continue to add or delete locations from your group.

Each group can contain up to a maximum of all of the One Touch and Auto Dial locations available on your fax machine.

6. When you are finished programming your group, press the NO

key. The display shows LOCATION PROGRAMMING ENTER (SRCH, OT, A/D, #).

7. To program another group, go back to Step 2. If you are finished,

press the Select Function key.

Note: After programming a group, you can check the locations

programmed into the group by carrying out Steps 1 - 3. At Step 4, repeatedly press the Start key to view all the programmed locations. To delete a location, press the NO

key.

Note: The locations programmed into groups can be printed. See

Telephone Directory in Reports later in this user’s guide.

Chapter 3 - Dial Directories 38

Page 47

Chapter 4 - Basic Operations

Preparing documents

• Try to use good quality documents for your transmissions. Documents that are typed or created in felt-tip black ink on white (or light) paper work best.

• Do not send documents which are not rectangular.

• Never use documents that have wet or sticky surfaces, wrinkles, staples or paper clips. However, your fax machine can transmit documents that have been subject to normal wear, such as documents with staple holes, letter folds and minor corner folds.

English

• If you are not sure how a document will fax, try making a copy first on your fax machine (load the document face down and press the COPY key).

• If your documents are very creased, torn, or crinkled, make a copy on a photocopier and send the copy instead. You can also use a photocopier to enlarge or reduce documents before sending.

Document size

All documents must have a minimum width of 148 mm and a minimum length of 128 mm. Documents cannot be wider than 216 mm or longer than 356 mm.

Multiple page documents

Your fax machine can scan paper with a base weight between 60 gsm and 105 gsm. You can load up to 20 sheets of standard 80 gsm paper (e.g. photocopier paper) at the same time. If you use a heavier paper, you can load up to 15 sheets. For very heavy paper, manually load sheets and send pages sheet-by-sheet.

When loading several pages for transmission, paper thickness should be between 0.08 mm and 0.13 mm. For single page transmission, paper thickness can be between 0.06 mm and 0.15 mm.

Chapter 4 - Basic Operations 39

Page 48

Loading documents

To prevent paper jams and problems during scanning, neatly stack your documents, aligning their edges, before loading. Do not load documents of different sizes at the same time and do not force the documents in to the document feeder to prevent multiple feeding and paper jams.

Note: You can load and prepare to transmit a document while your fax

machine is still sending or receiving another message (as long as the document feeder is clear). To do this, load the document, select your location and press the Start key. Your document will be scanned into memory and sent when the current communication ends.

1. Adjust the document guides to the width of the paper you are using.

English

2. Neatly stack your documents, then insert them face down into the

document feeder. If necessary, readjust the document guides for a snug fit.

3. Your fax machine will grip the documents and pull the bottom page

into the machine.

YES key to set the

4. If necessary, use the Transmit Resolution or

resolution of your document.

Chapter 4 - Basic Operations 40

Page 49

English

Original Document Set RESOLUTION to

Normal office documents Standard (STD) Documents with small type or other fine details Fine/Ex. Fine Documents with photos or many shades of grey Photo

5. If necessary, use the Type of Original or NO X key to set the level

of contrast in your document.

Original Document Set TYPE OF ORIGINAL to

Normal contrast Normal Contrast is too light Light Contrast is too dark Dark

6. Your documents are now ready for faxing or copying.

Sending fax to a single location

1. Load your documents.

2. Select a location. Refer to the instructions below.

To dial using Do this

A One Touch key Press the One Touch key.

An Auto Dial number

Numeric keypad

An external telephone

3. If necessary, press the Start key to begin the transmission. Refer to

the table below to understand some of the messages you may see during a typical fax transmission

Press the Auto Dial key, then enter the 3 digit Auto Dial number on the numeric keypad.

Dial as you would on a normal telephone. If you make a mistake,

YES key to go back and re-enter the number.

press the

Pick up the handset of your external telephone and dial the number of the machine you wish to transmit to. If the receiving fax machine is in automatic reception mode, you will hear a high-pitched tone. If a person answers the phone, ask them to press the Start key on their fax machine.

Chapter 4 - Basic Operations 41

Page 50

Message Explanation

The Personal ID or TSI/CSI of the remote location. If this is not

(location)

DIALLING Your fax machine is dialling the number. CALLING The line is ringing. SENDING Your fax machine is sending the message. RESULT = OK The fax was sent successfully.

COMMUN. ERROR

programmed in the remote location, the Location ID or telephone number you entered will identify the location during transmission.

If you see this or another error message, a problem occurred during the communication. Try resending the fax. Refer to Problem Solving for assistance.

Note: When the ISDN G4 option is installed, if a fax number is entered

with the numeric keypad, the fax machine shows the current transmission mode G3 or G4. To select the current setting, press the

YES key. To change the current setting, press the NO

key first and confirm this new setting with the W YES key.

English

Search key dialling

If you are not sure which One Touch key or Auto Dial number contains the location you want to communicate with, use the Search key to look through an alphabetical list of all of the Location IDs programmed into your fax machine.

1. When selecting locations, press the Search key. The display will

show ENTER 1’ST CHAR.

2. Repeatedly press the Search key to look through the entire list of

locations in alphabetical order, or locate the letter you want on the numeric keypad, and press that key repeatedly to look through Location IDs beginning with that letter.

3. Press the Start key as soon as the desired location appears on the

display.

Chapter 4 - Basic Operations 42

Page 51

Real-time dialling

Normally, your fax machine dials the entire number of the location you have selected at one time. Occasionally, it may be necessary to dial numbers in real time (one digit at a time). If your fax machine is equipped with a handset, you can dial in real time by picking up the handset or press the Hook/V. Request key.

Note: Real-time dialling with use of the Hook/V. Request key is not

available in some countries. Also, when the ISDN option is fitted, real-time dialling is not available.

Redialling

If the line is busy or if there is no answer, your fax machine waits and then automatically redials the number. Also, if your fax machine is transmitting from memory and a communication error occurs, it automatically redials the number and tries to send the fax again. You can redial a number manually at any time by pressing the Redial key.

English

Confirming results

After transmission, press the Copy key once (with no documents loaded) to see a report confirming your transmission on your fax machine’s display. To print the report, press the Copy key a second time. See “Chapter 7 - Reports” for more information.

Stopping a transmission

To stop a transmission while it is in progress, follow the instructions below.

1. Press the Stop key twice. The display will show STOPPED.

2. If documents are stuck part way through the document feeder, you

may see the following message on the display RELOAD DOCUMENT. Press the Stop key again. Your fax machine feeds the document the rest of the way through the document feeder.

Note: If your fax machine cannot feed your document through the

document feeder, refer to Problem Solving.

Chapter 4 - Basic Operations 43

Page 52

Receiving faxes manually

Note: Receiving faxes manually is not possible when the ISDN option

is fitted.

Your fax machine receives faxes automatically unless the fax machine has been set to the manual receive [TEL] mode. If your fax machine is set to the manual receive [TEL] mode, follow the instructions below.

1. When your telephone or fax machine rings, pick up the telephone

handset. If the call is a voice call, start speaking to the caller.

2. If the call is a fax call, or if a person wishes to fax you a document

after having a conversation, press the Start key.

3. When MANUAL START appears on the display, hang up the

handset.

Note: You can also tell your fax machine to start fax reception by

entering your 3 digit code for remote receive using your telephone keypad. Refer to Remote Receive.

English

4. After you receive the fax, a long beep tells you that the reception

was successful.

Receiving faxes in memory

Your fax machine automatically receives messages into memory and does not immediately print them in the following situations.

Memory reception

When your fax machine has been set to Memory Reception Mode [MEM], any received faxes are stored in the memory of your fax machine and are not automatically printed. The display shows MSG. IN MEMORY if any faxes have been received during memory reception mode.

When you change the reception mode of your fax machine, any nonconfidential fax messages stored in memory are automatically printed.

If you want to print any fax messages stored in memory without changing the reception mode, carry out the following:

1. Press the Select Function key.

2. Press the 2/Print Operation One Touch key. The display shows

PRINT MEMORY MSG?

Chapter 4 - Basic Operations 44

Page 53

3. Press the W YES key. The stored message begins printing.

Note: If a memory reception password has been set, you will have to

enter this password to print any messages stored in memory. See “Creating Memory Password “in “Programming”.

When all messages have been printed, your fax machine automatically returns to memory reception mode.

No paper reception

When your fax machine has run out of paper, a NO PAPER, REPLACE PAPER message appears on the display. Your fax machine continues to receive faxes into memory when it has run out of paper. Your fax machine automatically prints out any messages received in memory when the paper is replaced and the Stop key is pressed.

No toner reception

English

When your fax machine is running low on toner, it displays a TONER LOW, REPLACE TONER CART. message. Rather than risk printing an unreadable message, your fax machine automatically receives faxes into memory if user setting 22:NO TONER MEM. RX has been set to ON.

If your fax machine has received a message in memory because toner is low, MSG. IN MEMORY appears on the display. To print out a message stored in memory when toner is low, follow the instructions below.

1. Press the Select Function key.

2. Press the 2/Print Operation One Touch key. The display will show

PRINT MEMORY MSG?

3. Press the

W YES key and stored messages will begin printing.

Note 1: If a memory reception password has been set, you will have to

enter this password to print any messages stored in memory.

Note 2: Even if you see a TONER LOW message on your fax machine,

you may be able to use the 2/Print Operation One Touch key to continue printing faxes, but the print quality cannot be guaranteed. Replace the toner cartridge as soon as possible.

Chapter 4 - Basic Operations 45

Page 54

Cancelling messages stored in memory

It is also possible to erase messages received in memory without printing them.

1. After you have followed the instructions to print out messages

stored in memory, the display shows MSG. IN MEMORY, PRINTING.

2. To erase the message instead of printing it, press the Stop key. The

display shows CANCEL?

English

3. Press the

W YES key to erase the message from the memory of

your fax machine.

Rejecting unsolicited fax messages

The closed network option allows you to limit the locations your fax machine can communicate with. Using this function, you can set your fax machine to refuse to receive any faxes from locations whose telephone numbers are not programmed into your One Touch keys or Auto Dial numbers. Use of this function allows you to reject any unsolicited faxes such as advertising.

Note: In some countries, this function cannot be set by the user. Please

contact your supplier for assistance.

You can also set your fax machine not to send faxes to locations whose telephone numbers are not programmed into your One Touch keys or Auto Dial numbers.

The available settings are limit reception only (RX), limit both transmission and reception (T/R), and no limitation on transmission or reception (OFF). To use the closed network function, follow the instructions below.

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Press the

4. Using the numeric keypad, enter 08. The display shows

08:CLOSED NETWORK and the current setting of this function.

5. Press the NO

display.

Chapter 4 - Basic Operations 46

YES key. The display shows FUNCTION NO.[ ]

key until the setting you want appears in the

Page 55

6. Press the W YES key to confirm the new setting.

7. Press the Select Function key to finish.

Power failures and memory

If power is interrupted to your fax machine, the following problems occur:

• Any messages your fax machine has scanned into memory, but not yet transmitted, are lost.

• Any messages your fax machine has received into memory, but not yet printed, are lost.

• If you have loaded documents onto the document feeder of your fax machine, any dialling or transmission settings are lost.

Your fax machine prints a power outage report to inform you of a power failure. Use this report to determine which received messages you may have lost and which transmissions you may have to resend. Refer to Reports for more information.

English

Making copies

Your fax machine can also be used to make copies. You can make up to 50 copies at one time. Your fax machine automatically makes all copies in FINE mode. STD, EX.FINE and PHOTO mode can be selected manually by pressing the

1. Load the documents to be copied.

2. Press the Copy key. The display shows PRG. NO. OF COPIES

[1SETS]. If you want to make just one copy, you are finished. Your fax machine waits a moment, then begins copying.

3. To make multiple copies, enter the number of copies you want to

make on the numeric keypad. Then press the Copy key again. Your fax machine begins making the required number of copies.

Note: When the message PRG. NO. OF COPIES is displayed, the

degree of print resolution can be changed.

W YES key.

Chapter 4 - Basic Operations 47

Page 56

Making copies using manual paper feeder

The manual paper feeder of your fax machine allows you to make copies on a different type of paper than what is normally kept in the paper tray of your fax machine. To make copies using the manual paper feeder, follow the instructions below.

1. Load the documents to be copied.

2. Insert a sheet of paper, printing side up, into the manual paper

feeder slot until you feel the fax machine grab hold of the paper.

English

3. Press the Copy key.

Note: It is recommended to make single copies only when using the

manual paper feed slot. This will prevent any possible paper feed jams from occurring.

Using voice request

The voice request feature allows you to have a conversation with a person at a remote fax machine during a fax communication. Either the sender or receiver of the fax can initiate a voice request.

If you are sending a fax, you can answer a voice request only after all pages have been transmitted. If you are receiving a fax, you can answer a voice request after reception of each page.

You will know if the person on the other fax machine has issued a voice request when you hear a warbling tone. If you do not respond in approximately six seconds, the voice request is automatically cancelled.

Note 1: You will need to have either an attached handset or an external

telephone to use the voice request function.

Note 2: The voice request feature is not available if fax communication

takes place at speeds higher than 14,400 bps.

Chapter 4 - Basic Operations 48

Page 57

Initiating voice request

1. When the display shows SENDING or RECEIVING, press the

Hook/V. Request key.

2. When the other party answers your request, your fax machine emits

a repetitive warbling sound. The display shows LIFT HANDSET AND PRESS VOICE REQUEST.

3. Lift your handset and press the Hook/V. Request key.

Note 1: If you press your Hook/V. Request key to initiate a voice request

during transmission, but no one is there to answer, your fax machine automatically sends a call back message to the remote site giving a telephone number where you can be reached.

Note 2: A call back message is only sent if you have programmed a call

back number into your fax machine. Refer to Setting Fax Identification.

English

Note 3: To be able to initiate a voice request during transmission, user

function 17:MEM./FEEDER SW. must be set to FEED and 25:INSTANT DIALLING must be set to OFF. While initiating a voice request during reception, these settings are ignored.

Answering voice request

Lift your handset and press the Hook/V. Request key.

Chapter 4 - Basic Operations 49

Page 58

English

Chapter 5 - Advanced Operations

Sending faxes to multiple locations and/or groups

If you want to send the same fax to more than one location, carry out the following steps:

1. Load your document.

2. Select your first group or location as follows. The next group or

individual location must be selected within three seconds.

Select location using Do this

A group

A One Touch key

Auto Dial number

A number dialled on the numeric keypad

Press the Auto Dial key and then # key in the numeric keypad. Then enter the code number of the group you want to use.

Press the One Touch key. If display asks for confirmation of your selection, press the Start key.

Press Auto Dial key, then enter the 3 digit Auto Dial code number on the numeric keypad. If display asks for confirmation of your selection, press the Start key.

Dial as you would on a normal telephone and press the Start key. If the ISDN G4 option is fitted, the fax machine shows the current transmission mode G3 or G4. To select the current setting, press the W YES key. To change the current setting, press the NO X key first and confirm this new setting with the W YES key.

Note: If you want to send a fax to groups and individual locations, the

groups must be selected first.

3. When selecting another group, do not press the Auto Dial key, but

immediately press the # key and enter the code number for the next group you want to select.

4. Repeat Steps 2 to 3 until you have finished selecting groups and

individual locations.

Note: Up to 10 fax locations can be entered using the numeric keypad.

5. When you have finished selecting groups and/or individual

locations, quickly press the Start key and the display changes to ENTRY IS OK? DIAL (START) CHECK (

Chapter 5 - Advanced Operations 50

). If your entries are

Page 59

English

OK, press the Start key. Your fax machine then scans your document and begins to transmit to your selected locations.

6. When you have finished selecting your groups and individual

locations and you DO NOT press the Start key, the display shortly shows MULTI LOCATION xxxxxx

Note: xxxxxx indicates the locations you have selected. If your

locations exceed the capacity of the display, then only the first locations are shown on the second line of the display, e.g. #1, 03, *02, 4568; #1 indicates Group 1; 03 indicates One Touch key 03; *02 indicates Auto Dial 02; 4568 are the first four digits of a number entered using the numeric keypad.

7. If you want to confirm your entries by printing a report, press the

key and the display shows PRINT ENTRY REPORT?.

Press the

YES key and your fax machine prints a report showing

the locations you have selected. After printing the report, the display changes to CHECK LOCATION(S).

If your entries are OK, press the NO ENTRY IS OK? DIAL (START) CHECK (

key and the display shows

)

If your entries are OK, press the Start key. Your fax machine then scans your document and begins to transmit to your selected locations.

8. If you do not want to print a report, but want to confirm your

entries, press the NO

key and the display shows PRINT ENTRY

REPORT?

Then press the NO

key and the display changes to CHECK

LOCATION(S).

To check your selected locations, press the Start key and the display shows the first location you have entered xxxxxx OK (START) CLEAR (

)

Note: xxxxxx indicates the first location entered into your fax machine.

Keep pressing the Start key until you have checked all the locations you have entered until the display again shows CHECK LOCATION(S).

If your entries are OK, press the NO ENTRY IS OK? DIAL (START) CHECK (

Chapter 5 - Advanced Operations 51

key and the display shows

)

Page 60

English

If your entries are OK, press the Start key. Your fax machine then scans your document and begins to transmit to your selected locations.

9. If you want to cancel an entered location when checking locations,

press the NO CLEAR (

key when the display shows xxxxxx OK (START)

)

Note: xxxxxx indicates the location entered into your fax machine

which you may want to cancel.

The displayed location is cancelled and the display shows the next

key each time you want

location you have entered. Press the NO

to cancel a location entered into your fax machine. Press the Start key if the displayed location is OK and to move onto the next location you have entered into your fax machine.

10. If you want to add another group or location after checking the

groups and locations you have entered, select your new group or location when the display shows CHECK LOCATION(S).

Delayed sending of faxes

The delayed transmission feature allows you to send documents at a specified date and time, and frees you from the need to manually start the transmission. You can program a delayed transmission to occur at any time on the day of your transmission, or at any time over the next three days.

You can program your fax machine to send delayed faxes from the document feeder or from memory. Refer to the table below to decide which method you want to use.

Features and limitations From feeder From memory

Number of locations One Multiple Fax machine can be used for other transmissions while a

delayed fax is waiting to be sent.

Note: Sending a delayed fax from your fax machine does depend on the

settings of the user function 17:MEM./FEEDER SW.

No Yes

With user function 17:MEM./FEEDER SW. set to FEED and you are sending a delayed fax to a single location, only one delayed fax can be programmed for transmitting. Your document remains on the document feeder after programming the delayed transmission to a single location.

Chapter 5 - Advanced Operations 52

Page 61

This means that you cannot use your fax machine to send other faxes until your delayed fax has been sent.

With user function 17:MEM./FEEDER SW. set to MEM, a maximum of five individual faxes can be programmed into the memory of your fax machine for sending at a later date and time. After programming your delayed transmissions to single locations, your document is scanned into memory to wait for the programmed date and time. This setting allows you to continue to send other faxes from your fax machine.

If you send delayed faxes to groups and/or individual multiple locations, the setting of 17:MEM./FEEDER SW. is ignored. Delayed faxes are automatically scanned into memory.

Sending delayed faxes to single locations

1. Load the document you wish to send.

English

2. Press the Select Function key.

3. Press the 1/Delayed TX One Touch key. The display shows

DELAYED TX DATE and today’s date.

4. Press the

YES key and go to Step 7 if transmission is to occur

later today. If the transmission is to occur up to three days later, press the NO

key. The display shows DELAYED TX DATE [/]

PRG. DATE 0-9.

5. Using the numeric keypad, enter the date on which you wish the

transmission to begin. The display changes to DELAYED TX DATE [xx/xx] YES (

) NO (X).

Note: [xx/xx] indicates the date you have entered using the numeric

keypad.

YES key. The display shows DELAYED TX TIME [/]

6. Press the

PRG. TIME 0-9

7. Using the numeric keypad, enter the time on which you wish the

transmission to begin. The display changes to DELAYED TX TIME [xx/xx] YES (

W) NO (X).

Note 1: [xx/xx] indicates the time you have entered using the numeric

keypad.

Note 2: Enter the time using the 24-hour clock, i.e., 8:00 a.m. would be

entered as 08:00 and 8:00 p.m. would be entered as 20:00.

Chapter 5 - Advanced Operations 53

Page 62

8. Press the W YES key. The display shows SELECT LOCATION(S).

9. Select your location as follows.

Select location using Do this

English

A One Touch key

Auto Dial number

A number dialled on the numeric keypad

Press the One Touch key. If display asks for confirmation of your selection, press the Start key.

Press the Auto Dial key, then enter the 3 digit Auto Dial code number on the numeric keypad. If the display asks for confirmation of your selection, press the Start key.

Note 1: If user function 17:MEM./FEEDER SW. has been set to FEED

and you are sending a delayed fax to a single location, your document remains on the document feeder until your programmed date and time. This prevents you from sending further faxes until your delayed fax has been sent.

Note 2: If user function 17:MEM./FEEDER SW. has been set to MEM

and you are sending a delayed fax to a single location, your document is scanned into memory. When the programmed date and time is reached, your document is sent.

10. Repeat the above procedure if you want to send another delayed

fax. Please note that you can only program a maximum of five delayed transmissions into the memory of your fax machine.

Sending delayed faxes to groups and/or multiple individual locations

1. Load the document you wish to send.

2. Press the Select Function key.

3. Press the 1/Delayed TX One Touch key. The display shows

DELAYED TX DATE and today’s date.

4. Press the

later today. If the transmission is to occur up to three days later, press the NO PRG. DATE 0-9.

W YES key and go to Step 7 if transmission is to occur

X key. The display shows DELAYED TX DATE [/]

Chapter 5 - Advanced Operations 54

Page 63

English

5. Using the numeric keypad, enter the date on which you wish the

transmission to begin. The display changes to DELAYED TX DATE [xx/xx] YES (

) NO (X).

Note: [xx/xx] indicates the date you have entered using the numeric

keypad.

6. Press the

YES key. The display shows DELAYED TX TIME [/]

PRG. TIME 0-9

7. Using the numeric keypad, enter the time on which you wish the

transmission to begin. The display changes to DELAYED TX TIME [xx/xx] YES (

) NO (X).

Note 1: [xx/xx] indicates the time you have entered using the numeric

keypad.

Note 2: Enter the time using the 24-hour clock, i.e., 8:00 a.m. would be

entered as 08:00 and 8:00 p.m. would be entered as 20:00.

YES key and select your first group or location as

8. Press the

follows. The next group or individual location must be selected within three seconds.

Select location using Do this

A group

A One Touch key

Auto Dial number

A number dialled on the numeric keypad

Press the Auto Dial key and then # key in the numeric keypad. Then enter the code number of the group you want to use.

Press the One Touch key. If the display asks for confirmation of your selection, press the Start key.

Press the Auto Dial key, then enter the 3 digit Auto Dial code number on the numeric keypad. If the display asks for confirmation of your selection, press the Start key.

Dial as you would on a normal telephone. If the ISDN G4 option is fitted, the fax machine shows the current transmission mode G3 or G4. To select the current setting, press the W YES key. To change the current setting, press the NO X key first and confirm this new setting with the W YES key.

Note: If you want to send a fax to groups and individual locations, the

groups must be selected first.

9. When selecting another group, do not press the Auto Dial key, but

immediately press the # key and enter the code number for the next group you want to select.

10. Repeat Steps 8 to 9 until you have finished selecting groups and

individual locations.

Chapter 5 - Advanced Operations 55

Page 64

English

Note: Up to ten fax locations can be entered using the numeric keypad.

11. When you have finished selecting groups and/or individual

locations, quickly press the Start key and the display changes to

ENTRY IS OK? DIAL (START) CHECK (

12. If your entries are OK, press the Start key. Your fax machine then

scans your document and begins to transmit to your selected locations.

13. When you have finished selecting your groups and individual

locations and you DO NOT press the Start key, the display shortly shows MULTI LOCATION xxxxxx.

Note: xxxxxx indicates the locations you have selected. If your

14. If you want to confirm your entries by printing a report, press the

key and the display shows PRINT ENTRY REPORT?.

Press the

YES key and your fax machine prints a report showing

the locations you have selected. After printing the report, the display changes to CHECK LOCATION(S).

If your entries are OK, press the NO ENTRY IS OK? DIAL (START) CHECK (

key and the display shows

If your entries are OK, press the Start key. Your fax machine will then scan your document and begin to transmit to your selected locations.

15. If you do not want to print a report, but want to confirm your

entries, press the NO

key and the display shows PRINT ENTRY

REPORT?.

Then press the NO

key and the display changes to CHECK

LOCATION(S).

To check your selected locations, press the Start key and the display shows the first location you have entered xxxxxx OK (START) CLEAR (

Note: xxxxxx indicates the first location entered into your fax machine.

Chapter 5 - Advanced Operations 56

Page 65

English

Keep pressing the Start key until you have checked all the locations you have entered until the display again shows CHECK LOCATION(S) YES (STR/LOC.) EXIT (

If your entries are OK, press the NO ENTRY IS OK? DIAL (START) CHECK (

key and the display shows

If your entries are OK, press the Start key. Your fax machine will then scan your document and begin to transmit to your selected locations.

16. If you want to cancel an entered location when checking locations,

press the NO CLEAR (

key when the display shows xxxxxx OK (START)

Note: xxxxxx indicates the location entered into your fax machine

which you may want to cancel.

The displayed location will be cancelled and the display will show

key each time

the next location you have entered. Press the NO

you want to cancel a location entered into your fax machine. Press the Start key if the displayed location is OK and to move onto the next location you have entered into your fax machine.

17. If you want to add another group or location after checking the

groups and locations you have entered, select your new group or location when the display shows CHECK LOCATION(S).

18. If your entries are OK, press the NO

ENTRY IS OK? DIAL (START) CHECK (

key and the display shows

If your entries are OK, press the Start key. Your fax machine will then scan your document into the memory of your fax machine and wait until the programmed date and time is reached before sending your message.

Cancelling delayed transmission

To cancel a delayed transmission from the document feeder or from memory before it has been sent, follow the instructions below.

1. Press the Stop key. The display shows COMMUNICATION

CANCEL.

2. Press the

telephone number of the first delayed transmission currently loaded in your fax machine xxxxxx CANCEL (

W YES key. The display shows the Location ID or

W) OTHER (X).

Chapter 5 - Advanced Operations 57

Page 66

English

Note 1: xxxxxx indicates the location of a delayed transmission to a

single location or the first location of a delayed transmission to multiple locations.

Note 2: If you have programmed standard one-time polling or standard

bulletin polling into your fax machine, the display shows WAITING TO BE POLLED before the delayed transmissions. If

key first.

this is the case, press the NO

3. Press the

displayed. If more than one delayed transmission has been programmed into your fax machine, press the NO location of the delayed transmission you want to cancel appears, then press the

4. If the delayed transmission was a feeder transmission, press the

Stop key again to remove the document from the document feeder.

YES key to cancel the delayed transmission that is

key until the

YES key to cancel.

Confidential faxes

Fax machines are often placed in public places where anyone can look through received faxes. To overcome this, use the confidential fax feature when sending and/or receiving confidential faxes.

You can send and receive confidential faxes to and from other fax machines with personal mail boxes. However, the International Telecommunications Union (ITU) has now created a worldwide standard that uses ITU sub-addressing to allow fax machines or PC fax software from different manufacturers to send and receive confidential faxes.

When sending confidential faxes, you must know in advance the mail box number, or ITU sub-address, of the recipient you are sending the message to. Ask the person who is receiving the fax to tell you their mail box number, or ITU sub-address.

A receiving fax machine stores the message in a confidential mail box or ITU sub-address protected by a password and will not print any confidential faxes until the correct password is entered.

Sending confidential faxes

1. Load the document you wish to send.

2. Press the Select Function key.

Chapter 5 - Advanced Operations 58

Page 67

3. Press the 3/Confidential TX One Touch key. The display will ask

you to enter the number of the confidential mail box, or ITU subaddress, on the receiving fax machine.

4. Using the numeric keypad, enter the number of the confidential

mail box, or ITU sub-address, you are transmitting to and press the START key. The display shows SELECT LOCATION.

5. Select your location as follows.

Select location using Do this

A One Touch key Press the One Touch key.

Auto Dial number

A number dialled on the numeric keypad

Press Auto Dial key, then enter the 3 digit Auto Dial code number on the numeric keypad.

Dial as you would on a normal telephone.

Note: You cannot send a confidential fax to a group or multiple

individual locations.

English

6. Press the Start key and your fax machine will begin sending the

fax.

Receiving confidential faxes

Before you can receive confidential faxes, you have to create a confidential or personal mailbox on your fax machine that is password protected (see below). You then have to tell the person sending the confidential fax your mailbox number.

When your fax machine receives a confidential fax, it stores the fax in your personal mailbox. Your fax machine will automatically print a Confidential RX Report to indicate that a confidential fax has been received and is waiting to be printed. Also MSG. IN MEMORY appears on the display after receipt of a confidential fax.

Creating confidential mailbox

Create a confidential or personal mailbox on your fax machine as follows. This fax machine can have a maximum of eight confidential mailboxes.

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

Chapter 5 - Advanced Operations 59

Page 68

English

3. Using the numeric keypad, press number 5. The display shows

5:PERSONAL BOX PRG.

4. Press the

YES key and the display shows PERSONAL BOX NO.

[ ] ENTER 1 - 8.

5. Using the numeric keypad, enter the number (single digit between 1

and 8) of the personal mailbox you want to use and press the

YES key. The display normally shows PERSONAL BOX [CLOSE] YES (

6. Press the NO

[CONF] YES (

) NO (X).

key until the display shows PERSONAL BOX

) NO (X).

Note: If you cannot select [CONF], then the mailbox number you have

selected already contains a bulletin polling message. If you get the message ILLEGAL OPERATION, then the mailbox number you have selected already contains a confidential message in memory. Please select another personal box number to use.

YES key and the display shows PRG PASSWORD

7. Press the

[ ] ENTER 4DIGITS.

8. Using the numeric keypad, enter a four digit password and press the

YES key to confirm your entry. The display again shows

PERSONAL BOX NO. [ ] ENTER 1 - 8.

9. Continue to create personal mailboxes or press the Select Function

key to finish.

Closing confidential mailbox

Closing a confidential or personal mailbox created on your fax machine is as follows:

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 5. The display shows

5:PERSONAL BOX PRG.

4. Press the

[ ] ENTER 1 - 8.

5. Using the numeric keypad, enter the number of the personal

mailbox you want to close and the display shows PERSONAL BOX [CONF] YES (

W YES key and the display shows PERSONAL BOX NO.

W) NO (X).

Chapter 5 - Advanced Operations 60

Page 69

English

Note: If the message ILLEGAL OPERATION is displayed, the personal

mailbox you are trying to close contains messages. You must print any messages before closing the personal mailbox.

key until the display shows PERSONAL BOX

6. Press the NO

[CLOSE] YES (

) NO (X).

7. Press the

YES key and the display shows DELETE PERSONAL

BOX.

8. Press the

YES key to close the personal mailbox and the display

again shows PERSONAL BOX NO. [ ] ENTER 1 - 8.

9. Continue to close personal mailboxes created on your fax machine

or press the Select Function key to finish.

Changing mailbox password

Changing the password for a confidential or personal mailbox created on your fax machine is as follows:

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 5. The display shows

5:PERSONAL BOX PRG.

4. Press the

YES key and the display shows PERSONAL BOX NO.

[ ] ENTER 1 - 8.

5. Using the numeric keypad, enter the number of the personal

mailbox you want to close and the display shows PERSONAL BOX [CONF] YES (

) NO (X).

Note: If the message ILLEGAL OPERATION is displayed, the personal

mailbox you are trying to close contains messages. You must print any messages before closing the personal mailbox.

YES key and the display shows PRG PASSWORD

6. Press the

[XXXX] ENTER 4DIGITS.

7. Using the numeric keypad, enter a new four digit password and

press the

W YES key to confirm your entry. The display again

shows PERSONAL BOX NO. [ ] ENTER 1 - 8.

8. Press the Select Function key to finish.

Chapter 5 - Advanced Operations 61

Page 70

Printing confidential faxes

Each time your fax machine receives a confidential fax, it prints a Confidential RX Report telling you which personal box number has received a confidential fax. Printing a confidential fax from a personal box is as follows:

1. Press the Select Function key.

2. Press the 2/Print Operation One Touch key. The display shows

PRINT PERSONAL BOX?.

English

3. Press the

[ ] ENTER 0 - 8.

4. Using the numeric keypad, enter the number of the personal box

then press the PASSWORD [ ] ENTER 4DIGITS.

Note: If the personal mailbox you have selected contains no messages,

the display shows NO DATA IN MEMORY.

5. Using the numeric keypad, enter your four digit password then

press the

Note: If you want to clear the personal mailbox without waiting for the

message to be printed, press the Stop key at this point. The display changes to CANCEL? YES ( YES key and the message is cleared from the personal mailbox.

W YES key and the display shows PERSONAL BOX NO.

W YES key. The display changes to PRG.

W YES key. The received confidential fax starts printing.

) NO (X). Press the

Relay broadcasting

Relay broadcasting is where one fax machine, which is the relay initiating station, sends a document to another fax machine. The receiving fax machine, which is the relay key station, then re-sends (broadcasts) the document to a number of other locations.

Relay initiating station

Your fax machine can act as the relay initiating station which starts the relay broadcast by sending the original documents. Before programming your fax machine to initiate a relay broadcast, you need to obtain the following information from the operator of the fax machine you intend to use as a relay key station:

Chapter 5 - Advanced Operations 62

Page 71

Relay Password: This is the relay key word (up to 20 digits) which is programmed into the relay key station.

Relay Group Numbers: These numbers (up to 20 digits) are the code numbers of locations or groups of locations programmed into the relay key station.

Relay key station

The relay key station is the fax machine which receives the original fax message and then automatically relays or broadcasts the message to other fax machines. For this feature to be available, the relay key station must be a fax machine that has a sub-function for relay request.

Relay broadcast report

After a relay broadcast is completed, it is possible for the relay key station to send a message back to your fax machine confirming the success of the relay broadcast. For this function to work, the telephone number of your fax machine must be programmed into the Auto Dial list of your fax machine with the Auto Dial code number 70.

English

Initiating relay broadcast

1. Load the document you wish to relay.

2. Press the Select Function key.

3. Press the 4/Relay Initiate TX One Touch key. The display shows

RELAY PASSWORD.

4. Using the numeric keypad, enter a password of up to 20 digits,

which is the same as the relay password programmed into the relay key station.

Note: If you are initiating a relay broadcast to another relay key

key. Using the numeric keypad, enter the

station, press the NO 4-digit password of the other relay key station.

5. Press the Start key. The display shows REMOTE LIST NO.

6. Using the numeric keypad, enter a number of up to 20 digits which

corresponds to a relay group programmed into the relay key station.

Note: If you are initiating a relay broadcast to another relay group,

press the NO

number of the other relay group.

key. Using the numeric keypad, enter the 2-digit

Chapter 5 - Advanced Operations 63

Page 72

7. Press the Start key and the display changes to SELECT

LOCATION.

8. Select the location of the relay key station as follows:

Select location using Do this

A One Touch key Press the One Touch key.

Auto Dial number

A number dialled on the numeric keypad

Press Auto Dial key, then enter the 3 digit Auto Dial code number on the numeric keypad.

Dial as you would on a normal telephone.

9. Press the Start key. Your fax machine will begin sending the fax.

Polling

When you normally send faxes, you load your document into your fax machine, select a location and, if required, press the Start key to begin sending the document. However, sometimes it is more useful to be able to simply load your document into your fax machine and set it to wait for the another fax machine to call and collect the document. This is called setting your fax machine to be polled, or polling transmission. Calling another fax machine to receive documents someone else has loaded into their fax machine is called polling reception.

English

There are two standards for polling. Standard polling is to an old standard that is used by many, but not all manufacturers and ITU selective polling, which is the latest standard. Your fax machine supports both standards.

ITU selective polling allows you to retrieve documents from individual mailboxes or ITU sub-addresses from a fax machine that meets the standard for ITU selective polling.

Polling transmission

1. Load the document for polling.

2. Press the Select Function key.

3. Press the 5/Polling One Touch Key. The display shows BULLETIN

POLL.

4. For standard one-time polling, press the NO

17:MEM./FEEDER SW. has been set to FEED (see Programming), your document remains on the document feeder and waits for it to

X key. If user function

Chapter 5 - Advanced Operations 64

Page 73

English

be retrieved by the remote party. If the user function is set to MEM, your document is scanned into memory document and waits for it to be retrieved by the remote party. In both cases, the message WAITING TO BE POLLED appears on the display.

Note 1: Standard one-time polling uses the personal mailbox number of

0 to store the document in the memory of your fax machine. After your fax machine has been polled and the document has been sent, mailbox 0 is automatically cleared.

Note 2: If you get the message ALREADY EXIST on the display, then

mailbox 0 is already in use for standard one-time polling or standard bulletin polling. Either cancel the standard one-time polling or standard bulleting polling or use ITU bulletin polling.

YES key and the display

5. For standard bulletin polling, press the

changes to PERSONAL BOX NO. [ ] ENTER 0-8.

Note: Standard bulletin polling uses the personal mailbox number of 0

to store the document in the memory of your fax machine. After your fax machine has been polled and the document has been sent, your document remains in mailbox 0 allowing the document to retrieved more than once.

6. Using the numeric keypad, enter 0 for the personal mailbox you

YES key. Your document is then

want to use and press the

scanned into the memory of your fax machine and the message WAITING TO BE POLLED appears on the display.

Note: If you get the message ALREADY EXIST appearing on the

display, then the mailbox 0 is already in use for standard onetime polling or standard bulletin polling. To set up a new standard bulletin polling, you can either cancel the standard one-time polling or standard bulletin polling or use ITU bulletin polling as described below.

YES key and the display

7. For ITU bulletin polling, press the

changes to PERSONAL BOX NO. [ ] ENTER 0-8.

8. Using the numeric keypad, enter a number between 1 and 8 for the

personal mailbox you want to use and press the

YES key. Your

document is then scanned into the memory of your fax machine and the message BULLETIN MSG. IN MEM appears on the display.

Note 1: If you get the message ILLEGAL OPERATION appearing on the

display, then the personal mailbox you have selected is already

Chapter 5 - Advanced Operations 65

Page 74

in use as a confidential mailbox. Please select another personal mailbox to use.

Note 2: If you get message OVERWRITE appearing on the display, then

the personal mailbox you have selected is already in use for ITU bulletin polling. You can select another personal mailbox to use or over write the bulletin message already in the personal mailbox.

Note 3: After your fax machine has been polled and the document has

been sent, your document remains in mailbox allowing the document to retrieved more than once.

Polling reception

When carrying out polling reception, the fax machine you are polling should be able to carry out standard polling transmission or ITU polling transmission.

English

1. With no documents loaded, press the Select Function key.

2. Press the 5/Polling One Touch Key. The display shows NO.=<

MAIL BOX NO. >.

3. Press the Start key when the fax machine you are contacting

supports standard polling.

4. If the fax machine you are contacting supports ITU polling, using

the numeric keypad enter the number of the mailbox or ITU subaddress on the fax machine you are polling and press the Start key. The display changes to POLLING RX SELECT LOCATION.

5. Select the location of the fax machine you are polling as follows:

Select location using Do this

A One Touch key Press the One Touch key.

Auto Dial number

A number dialled on the numeric keypad

Press Auto Dial key, then enter the 3 digit Auto Dial code number on the numeric keypad.

Dial as you would on a normal telephone.

6. Press the Start key. Your fax machine will begin polling the remote

fax machine.

Chapter 5 - Advanced Operations 66

Page 75

Cancelling polling transmission

Standard one-time/bulletin polling

Cancelling a standard one-time polling transmission or a standard bulletin polling transmission is as follows:

1. Press the Stop key. The display shows COMMUNICATION

CANCEL.

English

2. Press the

POLLED CANCEL (

3. Press the

W YES key and the display changes to WAITING TO BE

W) OTHER (X).

W YES key and the polling transmission is cancelled.

ITU bulletin polling

To cancel an ITU bulletin polling transmission, you have to close the personal mailbox as follows:

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 5. The display shows

5:PERSONAL BOX PRG.

4. Press the

W YES key and the display shows PERSONAL BOX NO.

[ ] ENTER 1 - 8.

5. Using the numeric keypad, enter the number of the personal

mailbox you want to close and press the shows PERSONAL BOX [POLL] YES (

W YES key. The display

W) NO (X).

6. Press the NO

[CLOSE] YES (

7. Press the

BOX.

8. Press the

Printing bulletin messages

If you want to check any bulletin messages stored in a personal mailbox, you can print the messages as follows:

1. Press the Select Function key.

Chapter 5 - Advanced Operations 67

X key until the display shows PERSONAL BOX

W) NO (X).

W YES key and the display shows DELETE PERSONAL

YES key and the personal mailbox is closed.

Page 76

English

2. Press the 2/Print Operation One Touch key. The display shows

PRINT PERSONAL BOX [ ] YES (

) NO (X).

3. Press the

[ ] ENTER 0 - 8.

4. Using the numeric keypad, enter the number of the personal box

then press the message stored in the personal mailbox.

Note: Standard one-time polling messages cannot be printed.

YES key and the display shows PERSONAL BOX NO.

YES key. Your fax machine then prints the

Dual access

The advanced dual access feature of your fax machine allows you to load and prepare documents for transmission while your fax machine is sending or receiving another message, or automatically printing reports. This feature increases your productivity and reduces the time you must spend waiting for other operations to finish.

While sending faxes

After your fax machine has finished scanning a document into memory and is transmitting from memory, you can:

• Load another document and prepare it for transmission.

• Continue to load documents as long as there is memory available on your fax machine. When the first transmission is complete, the next fax is automatically sent.

• Make copies.

While receiving faxes

While your fax machine is receiving faxes, you can:

• Load another document and prepare it for transmission.

• Continue to load documents as long as there is memory available on your fax machine. When the first transmission is complete, the next fax is automatically sent.

• Continue to receive faxes while earlier messages are being printed if your fax machine has been set to memory reception mode.

Chapter 5 - Advanced Operations 68

Page 77

While making copies

While you are making copies with your fax machine, you can:

• Continue to receive faxes while copies are being printed if your fax machine has been set to memory reception mode.

While printing reports

While your fax machine is automatically printing reports, you can:

• Continue to receive faxes while reports are being automatically printed if your fax machine has enough memory available. When the report has finished printing, your received fax message is then printed.

• Continue to load documents as long as there is memory available on your fax machine. After the report is printed, your fax is automatically sent.

English

Chapter 5 - Advanced Operations 69

Page 78

Chapter 6 - Programming

Customising features and operations

Many features and functions of your fax machine have settings which can be changed to customise the operations of your fax machine. Because each country has different regulations, you may not be able to access all of the settings listed below. If you have trouble changing a setting, contact your supplier for assistance.

Viewing your current settings

Follow these instructions to obtain a configuration report showing your fax machine’s current settings.

English

1. Press the Select Function key.

2. Press the 6/Report Print One Touch key. The display show

1:ACTIVITY REPORT.

3. Using the numeric keypad, press 5. The display shows

5:CONFIGURATION.

4. Press the

5. Press the Select Function key to finish.

YES key and the report will begin printing.

User function settings

User function settings allow you to customize the general operation of your fax machine. Refer to the list below to determine which settings you may need to change, then refer to Changing User Function Settings to make the change.

Note: Depending on local telephone regulations, some of the following

user function settings may not be available.

User function settings list

01:MCF. (SINGLE-LOC.): This function automatically prints a Message Confirmation Report after each single location transmission or polling transmission. Available settings are on and off.

Chapter 6 - Programming 70

Page 79

English

02:MCF. (MULTI-LOC.): This function prints a general Message Confirmation Report and a detailed Broadcast Confirmation Report after each multiple location transmission. Available settings are on and off.

03:ERR. REPORT (MCF.): This function automatically prints a Message Confirmation Report each time an error occurs during a transmission or polling transmission operation. Available settings are on and off.

04:IMAGE IN MCF.: When a Message Confirmation Report is automatically printed, this function adds a portion of the first page your fax machine transmitted. This is printed at the bottom of the message confirmation report. Available settings are on and off.

Note: This image function only becomes effective if user function

17:MEM./FEEDER SW. is set to MEM and/or user function 25:INSTANT DIALLING is set to ON.

05:SENDER ID: This function controls the printing of your fax machine’s Sender ID on the faxes you send. When turned on, your fax machine’s Sender ID, date and time will be printed on each page slightly outside the image area of your document. When turned off, your Sender ID, date and time will not be printed. However, some fax machines will print your TSI/CSI.

06:MONITOR VOLUME: This function sets the volume your fax machine uses for telephone line monitoring sounds during dialling. Available settings are LOW, MID, H-MID, HIGH and OFF.

07:BUZZER VOLUME: This function sets the volume of the various beep and alarm tones your fax machine emits during operations. Available settings are low, middle and high.

08:CLOSED NETWORK: This function allows you to program your fax machine to refuse to receive faxes from or transmit faxes to locations whose telephone numbers have not been programmed into your fax machine’s One Touch keys or Auto Dial numbers. Using this function, you can set up a closed network of fax machines. If you do not want your fax machine to transmit faxes to or receive faxes from locations outside your network, select T/R. If you only want your fax machine to refuse to receive faxes from outside your network, select RX. Available settings are OFF, T/R and RX

09:TX MODE DEFAULT: This function allows you to change your fax machine’s default type of original, transmit and copy resolution settings. Unless you select otherwise using the Transmit Resolution/

YES or

Chapter 6 - Programming 71

Page 80

English

Type of Original/NO

X keys, your fax machine is set to use the STD and

NORMAL settings. If you are constantly sending faxes which require some other combination of transmission modes, use this function setting to change the default transmission modes to any other combination of settings. While you are programming, the new default combinations will appear on the LEDs above the Transmit Resolution/

Original/NO

key.

YES or Type of

10:T/F TIMER PRG.: When set to the telephone/fax answering mode, your fax machine automatically distinguishes between incoming voice and fax calls. If the incoming call is a voice call, your fax machine will ring to tell you to pick up the handset. If you do not answer, your fax machine automatically switches back to facsimile mode to allow the calling party to manually send a fax. The T/F TIMER function controls how long your fax machine waits before switching back to fax mode. Available settings are 20 seconds or 35 seconds

11:RING RESPONSE: This function controls how long your fax machine waits before answering an incoming telephone call when your fax machine is set to auto receive or telephone/fax auto switch answering modes. The available settings are 1 ring, 5 seconds, 10 seconds, 15 seconds or 20 seconds.

Note: If your fax machine is set to telephone/fax auto switch answering

mode, it is recommended that you set ring response to one ring.

12:DISTINCTIVE RING: Distinctive ringing is a service offered by some telephone services that allow you to have different numbers on one line, each with its own distinctive ring. In this way, when you get an incoming call, you can identify what number is being called by the ring pattern. Your local telephone service can provide you with more information about this service and if it is available. If available, this service is usually offered as a monthly charge to your normal telephone bill. To use this function, refer to Setting Distinctive Ring.

Note: If the ISDN G4 option is installed, T/F Timer Prg., Ring

Response and Distinctive Ring are not available.

13:PAPER SIZE: This function allows you to tell your fax machine what size of paper you are using in the paper tray and manual paper feed of your fax machine. Available settings are A4, letter, legal 13, legal 14, executive, A5, A6 and JIS B5.

14:USER LANGUAGE: This function allows you to switch between the two languages programmed into your fax machine

Chapter 6 - Programming 72

Page 81

English

15:INCOMING RING: This function controls the telephone ringing sound your fax machine makes when a call comes in. When this function is set to off, your fax machine will not ring during incoming calls. When set to on, your fax machine only rings when set to manual receive mode or 11:RING RESPONSE is set to 5 to 20 seconds (except 1 ring). When set to DRC, your fax machine rings for each incoming call with the same tone, even if you have function 12:DISTINCTIVE RING set to on. Available settings are ON, OFF and DRC.

Note: DRC is only available if the setting of user function

12:DISTINCTIVE RING is available. Also, when set to OFF,

there is no effect on ringer in telephone/fax auto switch answering mode.

16:REMOTE RECEIVE: When you receive an incoming call, this function allows you to remotely tell your fax machine to switch from telephone to fax mode to receive an incoming fax. To use this function, use the keypad of a handset or an external telephone to enter the code number of remote receive you have programmed into your fax machine. Available settings are off, 00, 11, 22, 33, 44, 55, 66, 77, 88, 99, ** and ##. This function only works if your telephone system is a tone dialling system.

17:MEM./FEEDER SW.: This function controls how your fax machine normally transmits fax messages to one location. Either scanning the document into memory first and then start dialling, or by transmitting directly from the document feeder after dialling. Available settings are MEM. and FEED.

Note: The setting of 17:MEM./FEEDER SW. only becomes effective if

user function 25:INSTANT DIALLING is set to OFF. If 25:INSTANT DIALLING is set to ON, all documents are scanned upon call origination.

18:POWER SAVE MODE: This function substantially reduces the amount of power your fax machine consumes when it is not in use. When this function is on, your fax machine automatically switches to power save mode after it has been idle for three minutes. When this occurs, your display shows POWER SAVE MODE PRESS “Start” to exit.

While in this mode, your fax machine automatically switches back to full operation after you press the Start key, when the telephone rings, when the telephone handset is lifted, or when a document is loaded. Available settings are on and off.

Chapter 6 - Programming 73

Page 82

English

Note: If you have purchased the optional MFP software and you have

connected your fax machine to a PC, it is recommended that you turn 18:POWER SAVE MODE off. Your PC cannot switch your fax machine back to full operation.

19:ECM FUNCTION: The error correction mode function helps your fax machine to improve communication in areas where telephone line conditions are poor. Available settings are ON and OFF.

Note 1: When using ECM, the transmitting fax machine automatically

checks the data as it is sent. If the receiving fax machine cannot verify the transmission, the transmitting fax machine will retransmit as necessary. Using ECM also increases transmission time because the data is checked as it is transmitted.

Note 2: When you set ECM to off, maximum fax communication in G3

mode is 14,400 bps.

20:REMOTE DIAGNOSIS: The remote diagnostics feature allows a service person to remotely dial and service your fax machine. Available settings are on and off.

21:PC/FAX SWITCH: When your fax machine is set to answer in PC Receive Mode and your optional MFP software is set to receive fax messages, all incoming calls are transferred directly to your PC. However, if you are experiencing a problem with your PC, you can tell your fax machine to receive and print faxes locally by setting this function to on. Available settings are on and off.

22:NO TONER MEM. RX: With this function turned on, your fax machine automatically receives and stores messages in its memory when toner is low. When turned off, messages print even if toner is low or empty. Available settings are on and off.

Note: The off setting allows time for you to replace the toner cartridge,

but quality of printing may become poor as the toner cartridge is exhausted.

23:MEM. FULL SAVE: With single location transmission and 17:MEM./FEEDER SW. set to MEM and 25:INSTANT DIALLING is

set to off, and with multiple location transmission, call origination starts after an entire document is read into memory. If during this process memory becomes full, a MEMORY OVERFLOW message is shown in the display and the display changes to SEND SCANNED PAGES.

Chapter 6 - Programming 74

Page 83

English

Press the NO X key, your fax machine gives an alarm, the scanning of your document stops and the display shows MEMORY OVERFLOW REFER TO USER GUIDE.

Press the Stop key and the remaining pages of your document are removed from your fax machine. The pages of your document that were scanned into memory are automatically deleted from the memory.

Press the

YES key and all pages of your document that were scanned

into memory will be sent. After the scanned pages have been sent, the display changes to RELOAD DOCUMENT.

After you have reloaded your document, you can send the remaining pages of your document with another fax transmission.

If this function is set to on and you DO NOT press the NO

key within

one minute of the message SEND SCANNED PAGES, your fax machine automatically starts sending the scanned pages. If this function is set to off and you DO NOT press the NO

key within one minute, your scanned

pages are cleared from the memory.

Available settings for this function are on and off.

24:CONTINUOUS TONE: With this function on, your fax machine will emit a continuous tone after receiving a message. Pressing the Stop key turns off the tone. Set this function to off and your fax machine will emit a short beep after receiving a fax message. Available settings are on and off.

25:INSTANT DIALLING: Set this function to start reading documents upon call origination when transmitting to a single location. Available settings are on and off.

26:RESTRICT ACCESS: Select whether or not you want restricted access. Turning on this function renders your restricted ID registration active. Available settings are on and off.

27:WIDTH REDUCTION: Turning this function on enables you to print received data at a slightly reduced width. Available settings are on and off.

28:TONER SAVE: This function allows you to select whether to use toner saving during facsimile printing when the remote sending fax machine has selected Fine or Extra Fine resolution. The settings are ON and OFF.

29:CNG COUNT: This function allows you to switch to a fax reception mode at a certain CNG signal quantity (1-5) when the unit is operating in FAX, TAD or TEL/FAX modes.

Chapter 6 - Programming 75

Page 84

English

Note: CNG Count is not supported when the ISDN G4 option is

installed.

30:600DPI FAX TX: This function allows you to enable 600dpiread when Ex.FINE is selected for the TX RESOLUTION. The settings are ON and OFF.

31:ISDN DIAL MODE:

Set to G3 - The call originates in G3 mode when dialled from the

numeric keypad. Speech Analogue transmission is requested from the network.

Set to G4 - The call originates in G4 mode when dialled from the numeric keypad. Non-restricted digital transmission is requested from the network.

Note: This function is only active when the ISDN option board is

installed.

32: SPEECH RECEIVE:

Set to OFF - incoming voice transmissions from the network will

not be answered.

Set to ON - incoming voice transmissions from the network will be answered.

33: OPTION I/F MODE:

Set to MFPI - Your machine operates in MFPI Mode

Set to SCN. - Your machine operates in “Flatbed Scanners” Mode

and ‘Down Load Print’ Mode (Down load a print that is connected to a Flatbed Scanner and direct-couples to a PC).

Set to NET - Your machine operates in “Down Load Print” Mode. (Down Load Print via a Network Server)

Note 1: After changing the setting of this function, you must reboot your

machine.

Note 2: This function is only active when the 1284 option board is

installed.

Chapter 6 - Programming 76

Page 85

English

34: PAPER SIZE CHECK: This mode is enabled only when your machine operates in “Down Load Print” mode.

Set to ON - your machine detects any paper size error when the paper size specified by the down loaded command and that set at the terminal differ.

Set to OFF - it does not detect the above paper size error.

Note 1: With Option I/F Mode set to ‘MFPI’, this function is disabled.

Note 2: This function is only active when the 1284 option board is

installed.

35: PRINT JOB T.O.: In “Down Load Print” and “Flatbed Scanner” modes, when data-transfer interruption (due to Centronics I/F malfunction etc.) results in time-out, the data-transfer monitoring timer automatically switches the machine from Print Mode to FAX Stand-by Mode to prevent print operation from being locked. The set values of data-transfer timeout are 5 sec., 30 sec., and 5 min. where 30 sec. is set as default.

Note 1: With Option I/F Mode set to ‘MFPI’, the function is disabled.

Note 2: This function is only active when the 1284 option board is

installed.

36: FLATBED TX MODE: This function selects the default resolution for FAX TX when a Flatbed Scanner is connected.

Set to STD - Transmission with 8 dots/mm x 7.7 lines/mm resolution.

Set to FINE - Transmission with 300 x 300-dpi resolution.

Note 1: With Option I/F Mode set to ‘MFPI’, the function is disabled.

Note 2: This function is only active when the 1284 option board is

installed.

37: FLATBED TX T.O: This function selects a timeout to wait between pages for receive data in FAX TX when a Flatbed Scanner is connected. The set values of timeout are off, 30 sec., and 1 min.

Note 1: With Option I/F Mode set to ‘MFPI’, the function is disabled.

Note 2: This function is only active when the 1284 option board is

installed.

Chapter 6 - Programming 77

Page 86

38: HALF SIZE SCAN: This function selects handling of the lower half of the reading data when a small size document was read from the Flatbed Scanner.

Set to OFF - Does not discard data.

Set to ON - Discards lower half data.

Note 1: With Option I/F Mode set to ‘MFPI’, the function is disabled.

Note 2: This function is only active when the 1284 option board is

installed.

Changing user function settings

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

English

3. Press the

YES key. The display shows FUNCTION NO.[ ].

4. Using the numeric keypad, enter the 2-digit number of the function

you want to change. This display then shows the name of the selected function.

5. Press the NO

function, then press the

key to cycle through the settings for the user

YES key to confirm your selection. The

name of the next user function appears in the display.

Note: If you are changing your fax machine’s TX MODE DEFAULT

settings, the new settings will appear on the LEDs above the

Transmit Resolution/

YES and the Type of Original/NO

6. To select another user function, press the Stop key and return to

step 4.

7. Press the Select Function key to finish.

Setting distinctive ring

Note: In some countries, distinctive ring service is not available from

the local telephone company.

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

Chapter 6 - Programming 78

Page 87

English

3. Press the X

YES key. The display shows FUNCTION NO.[ ]

ENTER 01-29.

4. Using the numeric keypad, enter 12. The display shows

12:DISTINCTIVE RING [OFF] YES (

5. Press the NO

RING [SET] YES (

6. Press the

key. The display changes to 12:DISTINCTIVE

) NO (X).

YES key. The display changes to SETUP FAX RING

) NO (X).

CALL FAX NUMBER NOW.

7. Using a separate telephone line, immediately dial the number

assigned to the fax machine (you must do this within 90 seconds). When your fax machine begins to ring, the display changes to AUTO DETECTING RING PATTERN.

Your fax machine then automatically detects and remembers its assigned ring pattern. When your fax machine has finished programming its ring pattern, the display shows DISTINCTIVE RING SET RESULT=OK.

After detecting and remembering the ring pattern, the display changes to DISTINCTIVE RING [ON] YES (

8. Press the

YES key to confirm your selection.

) NO (X).

9. Press the Select Function key to finish.

Note: Occasionally, your fax machine may not be able to detect the

ring pattern on its first try. If this happens, the display changes to DISTINCTIVE RING SET RESULT=NG. If this happens, follow the above instructions again.

Personal mailboxes

Personal mailboxes are used to store messages in memory of your fax machine for bulletin polling or receiving confidential faxes.

Note: To use a personal mailbox for confidential messages, refer to

Confidential Faxes in Advanced Operations.

Creating personal mailbox (polling)

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

Chapter 6 - Programming 79

Page 88

English

3. Using the numeric keypad, press number 5. The display shows

5:PERSONAL BOX PRG.

4. Press the

YES key and the display shows PERSONAL BOX

NO. [ ] ENTER 1 - 8.

5. Using the numeric keypad, enter the number (between 1 and 8) of

the personal mailbox you want to use and the display shows PERSONAL BOX [CLOSE] YES (

6. Press the NO

key and the display changes to [CONF], [POLL]

and [CLOSE] in that order. Keep pressing the NO display shows PERSONAL BOX [POLL] YES (

7. Press the

YES key and a personal mailbox is created for polling.

) NO (X).

key until the

) NO (X).

8. Press the Select Function key to finish.

Closing personal mailbox (polling)

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 5. The display shows

5:PERSONAL BOX PRG.

4. Press the

YES key and the display shows PERSONAL BOX

NO. [ ] ENTER 1 - 8.

5. Using the numeric keypad, enter the number of the personal

mailbox you want to close and the display shows PERSONAL BOX [POLL] YES (

6. Press the NO

[CLOSE] YES (

7. Press the

BOX YES (

8. Press the

YES key and the display shows DELETE PERSONAL

YES key to close the personal mailbox and the display

) NO (X).

key until the display shows PERSONAL BOX

) NO (X).

again shows PERSONAL BOX NO. [ ] ENTER 1 - 8.

9. Continue to close personal mailboxes created on your fax machine

or press the Select Function key to finish.

Chapter 6 - Programming 80

Page 89

Forward number programming

1. Press the Select Function key.

2. Press the 9/User Program One-Touch key. The display will show

1:FUNC. PROGRAMMING.

3. On the numeric keypad, press 6. The display shows 6:FORWARD

NO. PRG.

English

4. Press the

NO.).

5. Enter the number using the numeric keypad and press the Start key.

6. Press the Select Function key to finish.

Note To select forwarding of incoming non-confidential fax messages,

press the Auto Rec. key until the Forwarding mode, FWD, appears in the display.

YES key and the display shows NO= (FORWARDING

Memory password

When your fax machine has been set to Memory Reception Mode, you can protect the printing of stored messages by using a password.

Creating a memory password

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 7. The display shows

7:MEM. PASSWORD PRG.

4. Press the

[ ] ENTER 4DIGITS.

5. Using the numeric keypad, enter a four digit password and the

display changes to PRG. PASSWORD [xxxx] YES (

Note: [xxxx] indicates the four digit password you have entered.

6. Press the

PASSWORD PRG.

7. Press the Select Function key to finish.

Chapter 6 - Programming 81

YES key and the display shows PRG PASSWORD.

W) NO (X).

YES key and the display changes to 7:MEM.

Page 90

Changing a memory password

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 7. The display shows

7:MEM. PASSWORD PRG.

English

4. Press the

[XXXX] ENTER 4DIGITS.

5. Using the numeric keypad, enter a new four digit password and the

display changes to PRG. PASSWORD [xxxx] YES (

Note: [xxxx] indicates the four digit password you have entered.

6. Press the

PASSWORD PRG.

7. Press the Select Function key to finish.

YES key and the display shows PRG PASSWORD.

W) NO (X).

YES key and the display changes to 7:MEM.

Deleting a memory password

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 7. The display shows

7:MEM. PASSWORD PRG.

4. Press the

[XXXX] ENTER 4DIGITS.

5. To delete the password, press the 9/Space One Touch key and the

display changes to DELETE PASSWORD? YES (

6. Press the

7. Press the Select Function key to finish.

Restricted Access

Your fax machine can be programmed to restrict the use of your fax machine to designated individuals or departments. Please note that for restricted or department ID to work, user function 26:RESTRICT ACCESS must first be set to ON.

Chapter 6 - Programming 82

YES key and the display shows PRG PASSWORD.

) NO (X).

YES key and the password is deleted.

Page 91

Creating a restricted ID password

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press * key. The display shows

*:RESTRICT ID PRG.

English

4. Press the

YES key and the display shows DEPARTMENT NO.

[ ] ENTER 01-24.

5. Using the numeric keypad, enter a two digit code and the display

changes to ENTER ID [ ] ENTER 4DIGITS.

6. Using the numeric keypad, enter a four digit password and the

display changes to ENTER ID [xxxx].

Note: [xxxx] indicates the four digit password you have entered.

YES key and the display changes to DEPARTMENT

7. Press the

NO. [ ] ENTER 01-24.

8. Press the Select Function key to finish or continue to create

department ID numbers.

Changing a restricted ID

1. Using the numeric keypad, enter your four digit password.

2. Press the Select Function key.

3. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

4. Using the numeric keypad, press * key. The display shows

*:RESTRICT ID PRG.

5. Press the

[ ] ENTER 01-24.

6. Using the numeric keypad, enter the two digit code of the

department ID you want to change and the display changes to ENTER ID [XXXX] ENTER 4DIGITS.

7. Using the numeric keypad, enter the required four digit password

and the display changes to ID CLOSE.

Chapter 6 - Programming 83

YES key and the display shows DEPARTMENT NO.

Page 92

8. Press the NO X key and the display changes to ENTER ID [ ]

ENTER 4DIGITS.

9. Using the numeric keypad, enter a new four digit password and then

press the

YES key. The display changes to DEPARTMENT NO.

[ ] ENTER 01-24.

10. Press the Select Function key to finish or continue to change

department IDs.

Closing a Restricted ID

1. Using the numeric keypad, enter your four digit password.

2. Press the Select Function key.

3. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

English

4. Using the numeric keypad, press * key. The display shows

*:RESTRICT ID PRG.

5. Press the

YES key and the display shows DEPARTMENT NO.

[ ] ENTER 01-24.

6. Using the numeric keypad, enter the two digit code of the

department ID you want to close and the display changes to ENTER ID [XXXX] ENTER 4DIGITS.

7. Using the numeric keypad, enter the required four digit password

and the display changes to ID CLOSE.

8. Press the

YES key and the display changes to DEPARTMENT

NO. [ ] ENTER 01-24.

9. Press the Select Function key to finish or continue to close

department IDs.

Dial Parameter Settings

These functions allow you to control the way your fax machine dials telephone numbers. Refer to Dial Parameter Settings List to determine which settings you may need to change, then refer to Changing Your Dial Parameter Settings to make the change.

Note: Some settings are not available in some countries. If you have

trouble accessing a dial parameter setting listed here, contact your supplier for assistance.

Chapter 6 - Programming 84

Page 93

Dial parameter settings list

REDIAL TRIES: This function controls how many times your fax machine automatically redials a number which is busy or which does not answer. Available settings are from 0 to 10 tries

REDIAL INTERVAL: The function controls how long your fax machine waits between each automatic redial attempt. Available settings are from 1 to 6 minutes.

DIAL TONE DETECT: This function allows your fax machine to wait for and detect a dial tone before proceeding with dialling. Available settings are on and off.

BUSY TONE DETECT: This function allows your fax machine to detect a busy tone when sending a fax. Available settings are on and off.

MF(TONE)/DP(PULSE): This function controls what method your fax machine uses for dialling. Two dialling methods are in common use. DP, or dial pulse dialling, uses monotone pulses to dial a number (like a rotary telephone). MF, or multi-frequency dialling (touch tone), uses different tones to dial a number. Available settings are MF and DP.

English

PULSE DIAL RATE: If your fax machine is set to pulse dialling, this function controls how quickly your fax machine sends out dialling pulses (the dial pulse rate varies in different countries). Available settings are 10 pps, 16 pps and 20 pps.

PULSE MAKE RATIO: Available settings are 33%, 39% and 40%.

PULSE DIAL TYPE: If your fax machine is set to pulse dialling, this

function controls the type of pulse dialling used (different types of pulse dialling are used in different countries). Available settings are N, 10-N and N+1.

MF(TONE) DURATION: If your fax machine is set to tone dialling, this function controls the duration of the tones used for dialling (the tone duration varies in different countries). Available settings are 75 ms, 85 ms, and 100 ms.

PBX LINE: Turn this function on if your fax machine is connected to a PBX. Once this function has been turned on and the dial prefix function has been programmed, your fax machine will recognize the dial prefix number you use in your PBX to get an outside line. After it dials your dial prefix number, your fax machine pauses to wait for an outside line before dialling the rest of the telephone number. Available settings are on and

Chapter 6 - Programming 85

Page 94

off. See Connecting to a PBX in the Installation chapter for instructions on changing this setting.

FLASH/NORMAL: If your fax machine is connected to a PBX, this function tells your fax machine about the type of PBX line your fax machine is connected to. Available settings are normal (N) and flash (F).

AUTO START: When this function is turned on, your fax machine automatically begins dialling as soon as you have selected a location by pressing a One Touch key or entering an Auto Dial code. You do not have to press the Start key. Available settings are on and off.

DIAL PREFIX: If your fax machine is connected to a PBX, use this function to tell your fax machine what access number is used to obtain an outside line from your PBX. You can enter up to 4 digits. See Connecting to a PBX in Installation for instructions on changing this setting.

Changing dial parameter settings

English

1. Press the Select Function key.

2. Press the 9/User Program One Touch key. The display shows

1:FUNC. PROGRAMMING.

3. Using the numeric keypad, press number 2. The display shows

2:DIAL PARAMETER.

4. Press the

YES key until the display shows the dial parameter you

want to change.

5. Repeatedly press the NO

key until the setting you want appears

in the display.

6. Press the

YES key to confirm your selection. The name of the

next dial parameter setting will appear in the display.

7. Press the Select Function key to finish.

Chapter 6 - Programming 86

Page 95

Chapter 7 - Reports

Understanding reports

Your fax machine provides a variety of useful reports which help you understand the current settings, programming and operations of your fax machine. Refer to the reports listing below to determine which reports you may want to print, then refer to Printing Reports for instructions on printing a report.

Activity report

The activity report provides a communication record of your fax machine. Information provided on this report includes:

English

• The total amount of time your fax machine spent sending faxes and the total amount of time spent receiving faxes.

• The date, time and duration (S,R-TIME) of each transmission or reception.

• The name or telephone number of the fax machine you were communicating with (DISTANT STATION ID). If you were sending a fax, the Personal ID or telephone number of the remote fax machine that received the document will be printed. If the remote fax machine does not have a Personal ID or telephoned number programmed, the Location ID or telephone number you entered will be printed. If you were receiving a fax, the Personal ID or telephone number of the remote fax machine that sent the document will be printed. If you were receiving a fax and the remote fax machine does not have a Personal ID or telephone number programmed, no data is printed.

• The communication mode used for each transmission or reception.

• The number of pages sent or received.

• The result of each communication.

• Service codes.

Note: This report does not contain the results of fax messages which

were received without errors and printed immediately, i.e. only transmissions, receptions with errors and memory receptions are recorded.

Chapter 7 - Reports 87

Page 96

Broadcast confirmation report

Use this report to confirm the results of a multiple-location transmission (or broadcast). Information provided on this report includes:

• The date and time at which the broadcast started.

• The total amount of time used to complete the broadcast.

• For each location, the Location ID or telephone number, the number of pages sent and the result of the communication.

Note: If there have been no transmissions to multiple locations

(broadcast) then this report cannot be printed.

Active memory files report

The active memory files report provides a list of all fax messages stored in the memory of your fax machine, either documents waiting for transmission or documents which have been received and not yet printed. Information provided on this report includes:

English

• RECEPTION: prints out memory reception information. ENTRIES lists the number of received messages stored up in your facsimile unit’s memory. PAGES lists the total number of pages received.

• PERSONAL BOX: prints out set up status of your mailboxes (Confidential, Bulletin Polling). MODE describes the mailbox types. ENTRIES lists the number of received messages stored up in each mailbox. PAGES lists the total number of pages in each mailbox.

• POLLING TX/RX: prints out information on standard one-time polling transmission and standard bulletin polling transmission. Polling reception in Redialling Wait mode is also listed with the initiation date and time and the remote fax machine number or name.

• TRANSMISSION: prints out information on Delayed Fax and Redialling Wait transmissions.

Note: If there are no fax messages stored in the memory of your fax

machine, this report cannot be printed.

Telephone directory

This report provides a complete listing of all of the telephone numbers programmed into the One Touch keys, Auto Dial codes and groups of your fax machine. The information includes:

Chapter 7 - Reports 88

Page 97

• The Location ID and main fax number (TEL NO) for each One Touch key.

• The alternate number (OR) for each One Touch key.

• The G3 echo protection and communication speed settings for each One Touch key and Auto Dial code. If the G4 ISDN option is fitted, G3 or G4 will also be indicated.

• The Location ID and fax number (TEL NO) for each One Touch key and Auto Dial code.

• A listing of all of the One Touch keys and Auto Dial codes included in each group.

Configuration report

The configuration report provides a list of the current operational settings of your fax machine that can be set by you. The information includes:

English

• The current settings of all your fax machine’s user functions.

• The Sender ID (ID=), fax number (TEL NO.) and call back number (CALL BACK NO.) currently programmed into your fax machine.

• The current dial parameter settings of your fax machine.

Message confirmation report

This report provides information about your last single location fax transmission or polling transmission. Information in this report includes:

• The date of the communication.

• The total amount of time your fax machine spent sending (S,RTIME).

• The Personal ID or telephone number of the fax machine you were sending a fax to (DISTANT STATION ID). If the remote fax machine does not have a Personal ID or telephone number programmed, the Location ID or telephone number you entered is printed.

• The communication mode used.

• The number of pages sent or received.

• The result of the communication.

• Service codes.

Chapter 7 - Reports 89

Page 98

• Depending on the settings of your fax machine, a portion of the page will be printed after the report (see 04:IMAGE IN MCF. in Programming).

Confidential reception report

This report is automatically printed each time your fax machine receives a confidential message into a mailbox. Information in this report includes:

• The date the message was received.

• The total amount of time your fax machine spent receiving the message (S,R-TIME).

• The Personal ID or telephone number of the fax machine you were communicating with (DISTANT STATION ID). If the Personal ID or telephone number has not been programmed by the sending fax machine, no DISTANT STATION ID is recorded.

English

• The number of the mailbox into which the message was received.

• The number of pages received.

• The result of the communication.

• Service codes.

Broadcast entry report

Each time you program a multiple-location transmission (or broadcast), your fax machine gives you the option of printing this report to confirm your entries. Information in this report includes:

• The Location ID or telephone number of the One Touch keys and AUTO DIAL codes you have selected.

• Telephone numbers you have manually entered using the numeric keypad.

Power outage report

If the electrical power to your fax machine has been interrupted and your fax machine had delayed transmissions or messages received into memory, your fax machine automatically prints a power outage report to alert you that fax messages have been lost.

Chapter 7 - Reports 90

Page 99

Protocol dump

In the event of a communications failure, the protocol dump report can be printed out manually. This report can be helpful in analysing the cause of the communication failure. Send this report to the supplier or service centre if so requested.

Printing reports

Printing message confirmation report

After transmission, press the Copy key once (with no documents loaded) to see a report confirming your last transmission on the display of your fax machine. To print the report, press the Copy key a second time.

Printing other reports

English

1. Press the Select Function key.

2. Press the 6/Report Print One Touch key. The display shows

1:ACTIVITY REPORT.

3. Press the NO

X key repeatedly until the report you want to print

appears on the display.

4. Press the

W YES key. The report will begin printing.

5. Press the Select Function key to finish.

Codes used in reports

Result codes

The following codes indicate the results of communications.

Code Explanation

BUSY The line of the remote location was busy or there was no answer. CANCL A confidential message was erased after being held in memory for 10 days. COMP. A multiple-location transmission was completed. COVER The machine’s cover was opened during the communication. NO Transmission or reception failed due to a communications error. OK Transmission or reception was completed successfully.

Chapter 7 - Reports 91

Page 100

Code Explanation

PUNIT There is a problem with the printing unit. Contact service representative.

English

R_JAM

S_JAM A document jam occurred in the machine sending the fax. STOP Stop key was pressed, ending the session.

A paper jam occurred while receiving a fax, when the machine was unable to receive the entire message in memory.

Communication codes

The following codes indicate the communication mode used for a communication.

Code Explanation

TX A communication initiated by your fax machine.

POLL RX Polling reception POLL TX Polling transmission POLL=** Bulletin polling transmission (** is the mailbox number) CONF=** Confidential reception (** is the mailbox number) FWD-T Forwarding transmission

A communication initiated by a remote fax machine.

FWD-R Forwarding reception B.C. Broadcast transmission

Chapter 7 - Reports 92

Triumph Adler FAX 525 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual