INSTRUCTION HANDBOOK
DC 2215
As an ENERGY STAR Partner, UTAX GmbH, a company of TA Triumph-Adler AG,
has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
The ENERGY STAR program is an energy reduction plan introduced by the United
States Environmental Protection Agency in response to environmental issues and for
the purpose of advancing the development and utilization of more energy efficient
office equipment.
* ENERGY STAR is a U.S. registered mark.
This Instruction Handbook is also refering to a 18 ppm (pages per minute) copier, which has not
been launched by TA. The TA 2215 is referred to as the 15 ppm copier.
All rights reserved. No part of this material may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including photocopying, recording
or by any information storage and retrieval system, without permission in writing from
the Publisher.
Legal Restriction On Copying
• It may be prohibited to copy copyrighted material without permission of the copyright
owner.
• It is prohibited under any circumstances to copy domestic or foreign currencies.
• Copying other items may be prohibited.
Please read the instruction handbook before using the copier. Keep it close to the copier for easy
reference.
The sections of this handbook and parts of the copier marked with symbols are safety warnings meant to
protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the copier.
The symbols and their meanings are indicated below.
DANGER: Indicates that serious injury or even death will very possibly result from insufficient attention to
or incorrect compliance with the related points.
WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect
compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to
or incorrect compliance with the related points.
Symbols
The m symbol indicates that the related section includes safety warnings. Specific points of attention are
indicated inside the symbol.
................... [General warning]
................... [Warning of danger of electrical shock]
................... [Warning of high temperature]
The
symbol indicates that the related section includes information on prohibited actions. Specifics of the
prohibited action are indicated inside the symbol.
.................... [Warning of prohibited action]
.................... [Disassembly prohibited]
The ● symbol indicates that the related section includes information on actions which must be performed.
Specifics of the required action are indicated inside the symbol.
.................... [Alert of required action]
.................... [Remove the power plug from the outlet]
.................... [Always connect the copier to an outlet with a ground connection]
Please contact your service representative to order a replacement if the safety warnings in the handbook are
illegible or if the handbook itself is missing. (fee required)
CONTENTS
CHAPTER 1
IMPORTANT! PLEASE READ FIRST... 1-1
CAUTION LABELS ...................................1-1
INSTALLATION PRECAUTIONS ..............1-2
PRECAUTIONS FOR USE ....................... 1-3
CHAPTER 2
NAMES OF PARTS ............................... 2-1
(1) Main body ............................................2-1
(2) Operation panel ...................................2-4
CHAPTER 3
PREPARATIONS BEFORE USE .......... 3-1
1. How to load paper.......................................3-1
(1) Precautions for loading paper..............3-1
(2) Loading paper into the drawer .............3-1
(3) Loading paper into the multi-bypass....3-2
2. How to set originals ....................................3-5
(1) Setting originals into the DF ................3-5
(2) Setting an original on the platen ..........3-6
3. Replacing the toner container and
waste toner tank .........................................3-7
CHAPTER 6
COPIER DEFAULT SETTING ............... 6-1
1. Default settings ...........................................6-1
2. How to make default settings......................6-7
CHAPTER 7
WHEN A PROBLEM OCCURS ............. 7-1
1. Error display................................................7-1
2. When paper misfeeds .................................7-4
(1) Misfeed location indications.................7-4
(2) Cautions...............................................7-4
(3) Removal procedures............................7-5
3. Troubleshooting ..........................................7-9
CHAPTER 8
CLEANING AND SPECIFICATIONS..... 8-1
1. Cleaning the copier .....................................8-1
2. Specifications..............................................8-2
CHAPTER 4
BASIC OPERATIONS ...........................4-1
1. Basic copying procedure ............................4-1
2. Enlargement/reduction................................4-3
(1) Zoom copy ...........................................4-3
(2) Standard zoom copy............................4-3
3. Energy saver (auto preheat) function .........4-4
4. Auto shut-off function ..................................4-4
CHAPTER 5
FUNCTIONS .......................................... 5-1
1. Layout copying............................................5-1
2. Sort copying................................................5-4
i
MAKING FULL USE OF THE MACHINE'S ADVANCED FUNCTIONS
1 Various functions for making enlarged and
reduced copies
■ Enlarging/reducing copies to any size
in the 50 - 200% range
<Zoom copy mode> (page 4-3)
3 Making one copy from two or four originals
<Layout copy> (page 5-1)
* The 15 ppm copier requires the optional
memory copy board.
■ Making copies using the magnification
ratios preset in the copier
<Standard zoom mode> (page 4-3)
4 Sorting automatically
<Sort copy> (page 5-4)
* The 15 ppm copier requires the optional
memory copy board.
2 Making clear reproductions of
photographs
<Copy quality selection> (page 4-1)
5 A full range of optional equipment is
available
■ Drawer
A drawer of the same type as the
copier drawer can be added.
* This drawer is equipped with a cover
on the left side for removing misfed
paper.
■ Memory copy board (for 15 ppm
copier)
This memory copy board is required in
order to use various functions of this
copier, such as layout copying and sort
copying. Up to 30 originals of 6% black
coverage can be scanned with this
board.
* The 18 ppm copier comes standard
with a memory copy board installed.
ii
■ Printer board
If the printer board is installed, this
copier can be used as a printer. For
details, see the instruction handbook
for this option.
■ Printer network board
If the network board is installed along
with the optional printer board, this
copier can be used as a network
printer, allowing access from multiple
computers. For details, see the
instruction handbook for this option.
CHAPTER 1 IMPORTANT! PLEASE READ FIRST.
CAUTION LABELS
Caution labels have been attached to the copier at the following locations for safety purposes.
BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing toner.
Label 2
High temperature inside. Do not touch
parts in this area, because there is a
danger of getting burned.....................
Label 1
High voltage inside. NEVER touch
parts in this area, because there is a
danger of electric shock. .....................
Label 3
Drive mechanism inside. Do not touch
parts in this area, because there is a
danger of injury....................................
NOTE: DO NOT remove these labels.
1-1
INSTALLATION PRECAUTIONS
■Environment
CAUTION
• Avoid placing the copier on or in locations which are
unstable or not level. Such locations may cause the
copier to fall down or fall over. This type of situation
presents a danger of personal injury or damage to the
copier. .........................................................................
• Avoid locations with humidity or dust and dirt. If dust
or dirt become attached to the power plug, clean the
plug to avoid the danger of fire or electrical shock. ....
• Avoid locations near radiators, heaters, or other heat
sources, or locations near flammable items, to avoid
the danger of fire.........................................................
• To keep the copier cool and facilitate changing of
parts and maintenance, allow access space as shown
below.
Leave adequate space, especially around the left
cover, to allow air to be properly ventilated out of the
copier. .........................................................................
Rear:
1113/16", 30 cm
Left:
1911/16",
50 cm
Right:
1113/16",
30 cm
■Power supply/Grounding the copier
WARNING
• DO NOT use a power supply with a voltage other
than that specified. Avoid multiple connections in the
same outlet. These types of situations present a
danger of fire or electrical shock.................................
• Plug the power cord securely into the outlet. If
metallic objects come in contact with the prongs on
the plug, it may cause a fire or electric shock.............
• Always connect the copier to an outlet with a ground
connection to avoid the danger of fire or electrical
shock in case of an electric short. If an earth
connection is not possible, contact your service
representative. ............................................................
Other precautions
• Connect the power plug to the closest outlet possible
to the copier.
• The power supply cord is used as the main
disconnect device. Ensure that the socket/outlet is
located/installed near the equipment and is easily
accessible.
■Handling of plastic bags
WARNING
• Keep the plastic bags that are used with the copier
away from children. The plastic may cling to their
nose and mouth causing suffocation. .........................
Front:
3
39
/8", 100 cm
Other precautions
• Adverse environmental conditions may affect the safe
operation and performance of the copier. Install in an
air-conditioned room (recommended room
temperature: around 68°F(20°C), humidity: around
65%RH) and avoid the following locations when
selecting a site for the copier.
. Avoid locations near a window or with exposure to
direct sunlight.
. Avoid locations with vibrations.
. Avoid locations with drastic temperature fluctuations.
. Avoid locations with direct exposure to hot or cold air.
. Avoid poorly ventilated locations.
1-2
PRECAUTIONS FOR USE
■Cautions when using the copier
WARNING
• DO NOT place metallic objects or containers with
water (flower vases, flower pots, cups, etc.) on or
near the copier. This of situation presents a danger of
fire or electrical shock should they fall inside..............
• DO NOT remove any of the covers from the copier as
there is a danger of electrical shock from high voltage
parts inside the copier.................................................
• DO NOT damage, break or attempt to repair the
power cord. DO NOT place heavy objects on the
cord, pull it, bend it unnecessarily or cause any other
type of damage.
These types of situations present a danger of fire or
electrical shock. ..........................................................
• NEVER attempt to repair or disassemble the copier or
its parts as there is a danger of fire, electrical shock
or damage to the laser. If the laser beam escapes,
there is a danger of it causing blindness. ...................
• If the copier becomes excessively hot, smoke
appears from the copier, there is an odd smell, or any
other abnormal situation occurs, there is a danger of
fire or electrical shock. Turn the main switch OFF (O)
immediately, remove the power plug from the outlet
and contact your service representative. ....................
• If anything harmful (paper clips, water, other fluids,
etc.) falls into the copier, turn the main switch OFF
(O) immediately. Next, remove the power plug from
the outlet to avoid the danger of fire or electrical
shock. Then contact your service representative. ......
• DO NOT remove or connect the power plug with wet
hands, as there is a danger of electrical shock...........
• ALWAYS contact your service representative for
maintenance or repair of internal parts. ......................
CAUTION
• DO NOT pull the power cord when removing it from
the outlet. If the power cord is pulled, the wires may
become broken and there is a danger of fire or
electrical shock. (ALWAYS grasp the power plug
when removing the power cord from the outlet.) ........
• ALWAYS remove the power plug from the outlet when
moving the copier. If the power cord is damaged,
there is a danger of fire or electrical shock. ................
• If the copier will not be used for a short period of time
(overnight, etc.), turn the main switch OFF (O).
If it will not be used for an extended period of time
(vacations, etc.), remove the power plug from the
outlet for safety purposes during the time the copier is
not in use. ...................................................................
• ALWAYS hold the designated parts only when lifting
or moving the copier. ..................................................
• For safety purposes, ALWAYS remove the power
plug from the outlet when performing cleaning
operations. ..................................................................
• If dust accumulates within the copier, there is a
danger of fire or other trouble. It is therefore
recommended that you consult with your service
representative in regard to cleaning of internal parts.
This is particularly effective if accomplished prior to
seasons of high humidity. Consult with your service
representative in regard to the cost of cleaning the
internal parts of the copier. .........................................
Other precautions
• DO NOT place heavy objects on the copier or cause
other damage to the copier.
• DO NOT open the front cover, turn off the main
switch, or pull out the power plug during copying.
• During copying, some ozone is released, but the
amount does not cause any ill effect to one's health.
If, however, the copier is used over a long period of
time in a poorly ventilated room or when making an
extremely large number of copies, the smell may
become unpleasant. To maintain the appropriate
environment for copy work, it is suggested that the
room be properly ventilated.
• When lifting or moving the copier, contact your
service representative.
• Do not touch electrical parts, such as connectors or
printed circuit boards. They could be damaged by
static electricity.
• DO NOT attempt to perform any operations not
explained in this handbook.
• CAUTION : Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
• Do not open any cover or turn the power off while the
motor inside can be heard regardless of the condition
of the copier.
■Cautions when handling
consumables
CAUTION
• Avoid inhalation, ingestion, skin or eye contact. If
ingestion occurs, dilute stomach contents thoroughly
with water and seek medical treatment. If skin contact
occurs, wash with soap and water. If contact with
eyes occurs, flush thoroughly with water and seek
medical treatment. ......................................................
• Prolonged inhalation of excessive dusts may cause
lung damage. Use of this product, as intended, does
not result in inhalation of excessive dusts. .................
• Keep away from children. ...........................................
• Do not incinerate toner and toner containers.
Dangerous sparks may cause burn. ...........................
Other precautions
• Always read the safety instructions which are
included in the box or printed on the container when
handling consumables.
• Dispose of the toner or toner containers in
accordance with Federal, State and Local rules and
regulations.
• Store consumables in a cool, dark location.
• If the copier will not be used for an extended period of
time, remove the paper from the cassette, return it to
its original package and reseal it.
1-3
@0
fl
›‹ (
CHAPTER 2 NAMES OF PARTS
(1) Main body
18 ppm copier 15 ppm copier
6
9
8
!
123
12°
5
4
7
¤
fi
9
8
4
7
¤
fi
!
@0
fl ›‹
(
2-1
%
⁄
$ # ‡
^
)
*
&
1 DF (Document Feeder)
(Open/close to set the original on the platen.)
2 Original table
(Place the originals here.)
3 Original insertion guides
(Adjust the guides to the width of the originals.)
4 DF open/close handle
(Hold this handle when opening and closing the DF.)
5 Original eject cover
(Copied originals are stored here.)
6 DF original switchback cover
(Open this cover to remove a misfed original from the DF.)
7 Operation panel
(Contains the keys and indicators for operating the copier.)
8 Left cover handle
(Hold to open the left cover.)
9 Left cover
(Open when a paper misfeed occurs.)
0 Multi-Bypass
(Load paper here when copying onto small-size or special paper.)
! Insert guides
(Align the guides with the paper width when loading paper on the
multi-bypass.)
@ Support guide
(Pull out when loading paper into the multi-bypass.)
# Toner container
$ Waste toner tank
% Cleaning shaft
(Pull out and push back in several times after toner container
replacement or when copy images are soiled with toner.)
^ Front cover
(Open to replace the toner container and waste toner tank.)
& Main switch
(Turn ON (|) before starting to make copies.)
* Copy storage section
(Copied paper is stored here.)
( Drawer
(Holds up to 250 sheets of standard paper [standard paper as
specified by our company].)
) Platen
(Set originals here for copying. Place originals face-down with the
edges aligned with the size scales on the left and rear sides of the
platen.)
⁄ Original size scales
(Be sure to align the original with these when setting the original
on the platen.)
¤ Length guide
(Adjust to the length of the paper to be set in the drawer.)
‹ Width guide
(Adjust to the width of the paper to be set in the drawer.)
› Width adjustment lever
(Hold the lever and adjust the width guide to the width of the paper
to be set in the drawer.)
fi Length guide storage section
(Store the length guide here when it is not used.)
fl Drawer bottom plate
(Push down when loading paper.)
‡ Handles for transport
(The handles are located on the right and left sides of the copier.
Hold these two handles when moving the copier.)
— Original holder (15 ppm copier)
(Copied originals are ejected onto this holder.)
CHAPTER 2 NAMES OF PARTS
2-2
CHAPTER 2 NAMES OF PARTS
Inch specifications
European metric specifications
9* ^() 0!
4
1236 587@%& #$⁄
9* ^() 0!
4
Asia and Oceania metric specifications
1236 587@%& #$⁄
9* ^() 0!
4
1236 587@%& #$⁄
2-3
CHAPTER 2 NAMES OF PARTS
(2) Operation panel
1 Start key (indicator)
(Press to start copying. Copying is possible when the indicator is lit
green.)
2 Stop/Reset key
(Stop: Interrupts or aborts copying and printing.
Reset: Cancels settings and returns the copier in the initial mode.)
3 Size Select key
(Press when copying using the standard zoom mode. See page
4-3.)
4 Data/On-line indicator
(Lights while using the optional printer function or receiving data
from a computer.)
5 Printer key
(Press to use the optional printer function.)
6 Number of Copies/Zoom (+) key
(Press to increase the number of copies or magnification ratio.)
7 Number of Copies/Zoom (-) key
(Press to decrease the number of copies or magnification ratio.)
8 Zoom Input/Enter key
(Press when copying using the zoom copy mode. See page 4-3.)
9 Copy quantity/magnification display
(Displays the number of copies to be made and magnification ratio
for reduction/enlargement copying. When displaying a
magnification ratio, % will light.)
0 Add Toner indicator
(Flashes when the level of toner becomes low; lights when toner is
used up. See page 3-7.)
! Memory Overflow/Data Error indicator
(Lights when the memory becomes full while scanning originals.
Also lights when an error occurs while using the optional printer
function.)
@ Paper Select key
(Press to select a drawer or the multi-bypass. The indicator for the
selected paper source will light.)
# Upper drawer indicator
(Lights when the upper drawer is selected; flashes when a paper
misfeed occurs or paper is used up.)
$ Lower drawer indicator
(Lights when the optional lower drawer is selected; flashes when a
paper misfeed occurs or paper is used up.)
% Multi-bypass indicator
(Lights when the multi-bypass is selected; flashes when a paper
misfeed occurs or paper is used up.)
^ DF indicator
(Lights green when an original is placed in the DF; lights red when
an original misfeed occurs.)
& Misfeed indicator
(Lights when a misfeed occurs.)
* Image mode selection key
(Press to select the type of the original.)
( 2 in 1/4 in 1 key
(Press when using the 2 in 1 or 4 in 1 function. See page 5-1.)
) Sort key (indicator)
(Press to sort copies into separate sets. See page 5-4.)
⁄ Copy exposure adjustment keys
(Press the left key to make the copy density lighter; press the right
key to make it darker.)
● Initial mode (at the end of warm-up or when the Reset key is
pressed)
In the initial mode, the upper drawer is selected as the paper feed
drawer, the number of copies is set to “1” and the image mode is
set to “Text & Photo”.
* If the optional drawer is installed, the drawer selected in the initial
mode can be changed (see “Default drawer” on page 6-2).
* The image mode selected in the initial mode can be changed
(see “Image mode” on page 6-1).
● Auto clear function
About 90 seconds after copying stops, the copier will automatically
return to the same settings as those after warm-up. (However, the
exposure mode will not change.) Copying can be performed at the
same settings (copy mode, number of copies and exposure) if
copying is started before the auto clear function clears settings.
● Automatic drawer switching function
If two drawers contain paper of the same size and the paper in one
drawer runs out during copying, this function switches paper feed
from the empty drawer to the full drawer without interrupting
copying.
* This function requires the optional drawer.
* The automatic drawer switching function can be disabled (see
“Automatic drawer switching” on page 6-2).
2-4
CHAPTER 3 PREPARATIONS BEFORE USE
1. How to load paper
Paper can be loaded into the drawer and the multi-bypass.
(1) Precautions for loading paper
After unpacking the paper, ruffle it several times and then load into the
tray.
(2) Loading paper into the drawer
Up to 250 sheets of standard paper (64 to 80 g/m2/standard paper as
specified by our company) or colored paper can be loaded into the
drawer.
Press the drawer bottom plate down and lock it there.
2
Holding the width adjustment lever, move it to align the width
3
guide with the required paper width.
Paper sizes are marked inside the drawer.
Set the drawer paper size according to the size of paper to be loaded
(see “Upper drawer paper size” and “Lower drawer paper size
(optional)” on pages 6-2, 6-3 and 6-7). It is set to 8 1/2" x 11" (letter)/
A4 at the factory.
(Inch specifications)
* The drawer can hold paper of 8 1/2" x 14" (legal), 8 1/2" x 11" and 5
1/2" x 8 1/2" (vertical) sizes.
(Metric specifications)
* The drawer can hold paper of A4, A5 (vertical) and folio sizes.
Pull the drawer out toward you as far as it will go.
1
* If the optional drawer is installed, do not pull more than one
drawer out at a time.
While squeezing the presses on the sides, remove the length
4
guide and then insert it into the holes of the required paper
length.
Paper sizes are marked inside the drawer.
3-1
CHAPTER 3 PREPARATIONS BEFORE USE
* If the paper reaches the right-hand wall of the drawer, the
length guide is not used. Store it in the space shown in the
illustration.
Set the paper flush against the left-hand wall of the drawer.
5
Gently push the drawer back in.
6
* Check that the paper is kept under the claw of the drawer. If
not, reload the paper.
NOTE
Leaving paper out of its package under high temperature and high
humidity conditions may lead to problems caused by ambient
moisture. After loading paper into drawers, store the remaining paper
sealed in the paper storage bag. Also, before leaving the copier in
disuse for a prolonged period of time, remove the paper from the
drawer(s) and seal it in the paper storage bag to protect it from
moisture.
IMPORTANT
* Load paper so that it is kept under the claw of the drawer.
* When loading paper into the drawer, make sure that the copy side is
facing upward (the copy side is the side facing upward when the
package is opened.)
* Check that the length and width guides securely contact the paper. If
there is a gap, adjust the position of the length or width guide to
close it.
* Load paper all at once and do not add paper until all sheets are
used up. If you add paper to a drawer that still contains paper, a
paper misfeed may occur.
* Do not use paper with curls, creases, folds, or with rough or uneven
edges caused by improper cutting.
Depending on the type, cut condition, or storage condition of the
paper, copied paper may become extremely curled or a paper
misfeed may occur. Should such problems occur, remove the paper
from the drawer and turn the paper upside down.
(3) Loading paper into the multi-bypass
Standard paper (60 - 160 g/m2/standard paper as specified by our
company), colored paper and special paper can be loaded into the
multi-bypass.
The multi-bypass can hold up to 50 sheets of standard paper of 64 to
80 g/m2.
(Inch specifications)
The multi-bypass can hold paper of any size from 8 1/2" x 14" (legal)
to 5 1/2" x 8 1/2" (vertical).
(Metric specifications)
The multi-bypass can hold paper of any size from folio to A6 (vertical).
The types of special paper that can be used with the multi-bypass and
the number of sheets that can be loaded are as follows:
• Transparencies: 1 sheet
• Standard paper (160 g/m2): 1 sheet
* When copying onto special paper, be sure to use the multi-bypass.
Open the multi-bypass.
1
3-2
CHAPTER 3 PREPARATIONS BEFORE USE
Pull out the support guide.
2
Adjust the insert guides to the width of the paper to be
3
loaded.
IMPORTANT
* When loading paper into the multi-bypass, make sure that the copy
side is facing downward. (The copy side is the side facing upward
when the package is opened.) If the leading edge of the paper is
curled, straighten it out before loading the paper in the multi-bypass.
* Do not leave paper loaded in the multi-bypass when it is not used. If
you do, a paper misfeed may occur.
* When loading paper into the multi-bypass, place it lengthwise as
shown in the illustration. Do not load paper widthwise.
Copier
Copier
Insert the paper along the insert guides as far as it will go.
4
● Setting the paper size for the multi-bypass
Set the paper size for the multi-bypass according to the paper to be
loaded.
When you select the multi-bypass by pressing the Paper
1
Select key, the multi-bypass indicator flashes and the current
paper size of the multi-bypass is indicated on the copy
quantity/magnification display.
(Inch specifications)
-L-: Legal, letter
-S-: Statement
XXX: Setting of non-standard size paper width for multi-
bypass
(Metric specifications)
-A4: A4
-A5: A5
-A6: A6
-FL: Folio
XXX: Setting of non-standard size paper width for multi-
bypass
* Setting of non-standard size paper width for multi-bypass
will not be displayed if “OFF” is selected in “Turning multibypass non-standard size paper setting ON/OFF” (see
page 6-3).
3-3
(English text panel) (Symbol panel)
CHAPTER 3 PREPARATIONS BEFORE USE
Select the paper size by changing the display indication
2
using the Paper Select key.
(Inch specifications) (Metric specifications)
The display indication can also be changed using the
Number of Copies/Zoom (+) key or Number of Copies/Zoom
(-) key.
(English text panel) (Symbol panel)
Open the multi-bypass.
1
Pull out the support guide.
2
Press the Zoom Input/Enter key. The multi-bypass indicator
3
will light and normal copying enabled.
(English text panel) (Symbol panel)
● Setting envelopes
When using the optional printer function, envelopes can be set in the
multi-bypass.
Adjust the insert guides to the width of the envelope to be
3
loaded.
Set the envelope with the print side face-down and the flap
4
toward you and then insert it along the insert guides as far as
it will go.
* Incorrectly loading envelopes can result in printing in the
wrong orientation or on the wrong side.
NOTE
The types of envelopes that can be used are COM-10, Monarch, DL
and C5. Up to 6 envelopes can be loaded in the multi-bypass at a
time.
3-4
CHAPTER 3 PREPARATIONS BEFORE USE
2. How to set originals
(1) Setting originals into the DF
Precautions for the use of DF
Do not use any of the originals given below with the DF. Also do not
set originals with punch holes or tear-off strips positioned as the
leading edge.
• Transparency films
• Carbon paper and extremely creased or folded originals, originals of
soft material such as vinyl
• Non-square originals, wet originals, originals with adhesive tape or
glue
• Originals bundled with a paper clip or staple (if inevitable, remove
the paper clip or staple and straighten out the creases and folds
before setting the originals)
• Clipped out originals, originals with slippery surfaces
• Originals with still-wet whiteout
• Originals with creases (if inevitable, straighten out the creases
before setting the originals)
● 18 ppm copier
The DF automatically feeds multiple sheet originals one by one for
scanning.
Originals that can be used with the DF
(Inch specifications)
• Sheet originals only
• Original weights: Single-sided original of 50 to 120 g/m
• Original sizes: 8 1/2" x 11", 5 1/2" x 8 1/2" (vertical), 8 1/2" x 14"
• Capacity:
Up to 30 sheets of standard paper of 50 to 80 g/m
As many sheets of standard paper of 80 to 120 g/m2 (excluding
80 g/m2) as can be loaded up to the limit indicated on the sticker
attached on the rear original insertion guide
1 sheet of special paper (art paper, thermal paper)
2
2
Setting originals
Adjust the original insertion guides to the original size.
1
* Before setting the originals in the DF, check that no original
from the previous operation remains on the original eject
cover. Originals remaining on the original eject cover may
cause an original misfeed.
Set the originals on the original table in correct sequence
2
with the side to be copied facing upward. Securely insert the
leading edge of the originals into the DF as far as they will
go.
(Metric specifications)
• Sheet originals only
• Original weights: Single-sided original of 50 to 120 g/m
• Original sizes: A4, A5 (vertical), folio
• Capacity:
Up to 30 sheets of standard paper of 50 to 80 g/m
As many sheets of standard paper of 80 to 120 g/m2 (excluding
80 g/m2) as can be loaded up to the limit indicated on the sticker
attached on the rear original insertion guide
1 sheet of special paper (art paper, thermal paper)
2
2
IMPORTANT
Do not set originals exceeding the limit indicated on the sticker
attached on the rear original insertion guide. Setting more originals
than specified may cause an original misfeed.
3-5
CHAPTER 3 PREPARATIONS BEFORE USE
● 15 ppm copier
When an original is set in the DF, copying will automatically start (see
“DF auto start” on page 6-3).
* Enlargement and reduction copying is not possible when the DF is
used.
Originals that can be used with the DF
(Inch specifications)
• Sheet originals only
• Original weights: Single-sided original of 50 to 120 g/m
• Original sizes: 8 1/2" x 11", 8 1/2" x 14"
• Capacity: 1 sheet
(Metric specifications)
• Sheet originals only
• Original weights: Single-sided original of 50 to 120 g/m
• Original sizes: A4, folio
• Capacity: 1 sheet
Setting an original
* Before setting an original in the DF, check that no original remains
on the original holder. Originals remaining on the original holder may
cause an original misfeed.
* The original holder can hold up to 10 originals.
Set the original against the rear of the DF with the side to be copied
facing downward.
2
2
(2) Setting an original on the platen
When using an original that cannot be set in the DF, such as a book
or magazine, open the DF and place it on the platen.
Holding the DF open/close handle, open the DF.
1
* Before opening the DF, check that no original is present on
the original table or original eject cover. If present, the
originals may fall off when the DF is opened.
Set the original with the side to be copied facing downward.
2
Be sure to align a corner of the original with the rear left
corner of the platen.
* On rare occasions, the copy image may become slightly distorted
when the DF is used depending on the condition of the original. If
this problem occurs, make copies by placing originals on the platen.
IMPORTANT
When copying two or more originals, wait until the preceding original
is completely ejected before setting another original in the DF. Setting
an original while another original is being ejected may cause an
original misfeed.
IMPORTANT
15 ppm copier
Do not touch the gear near the rear left corner of the platen. If you do,
your hands may be soiled or injury may result.
CAUTION
DO NOT leave the document feeder open as there is a
danger of personal injury.
3-6
CHAPTER 3 PREPARATIONS BEFORE USE
3. Replacing the toner container and waste toner tank
When the level of toner becomes low, the Add Toner indicator flashes.
If you continue copying with the Add Toner indicator flashing, the
indicator eventually remains lit and a toner replacement message will
be printed out. When the message is printed, replace the toner
container and waste toner tank immediately. Be sure to replace the
waste toner tank when replacing the toner container. Use the new
waste toner tank that is supplied with the toner container.
The toner replacement message is as follows:
“Replace waste toner tank at the time of toner container exchange
surely, and do charge wire cleaning.”
* Replenish toner only when the Add Toner indicator is lit.
(English text panel) (Symbol panel)
Open the front cover.
1
Remove the waste toner tank.
2
CAUTION
Do not incinerate toner and toner containers. Dangerous
sparks may cause burns.
WARNING
High voltage is present in the charger section. Take
sufficient care when working in this area, as there is a
danger of electrical shock.
Close the opening of the waste toner tank with its seal.
3
1 2
CAUTION
Do not incinerate toner and toner containers. Dangerous
sparks may cause burns.
3-7
CHAPTER 3 PREPARATIONS BEFORE USE
Slide the toner container to the left and then pull it out toward
4
you.
WARNING
High voltage is present in the charger section. Take
sufficient care when working in this area, as there is a
danger of electrical shock.
Gently pull the cleaning shaft out as far as it will go and push
5
it back in 2 to 3 times.
Install the toner container.
7
* First insert the toner container into the copier as far as it will
go and then slide it to the right as indicated by the marked
arrows.
Install the waste toner tank.
8
IMPORTANT
Do not pull the cleaning shaft with force or pull it out completely.
Hold the new toner container vertically and tap the top 15
6
times. Turn the container upside-down and tap the top 15
times. Then, hold the container horizontally and shake it from
side to side 10 times.
NOTE
If the waste toner tank is not installed correctly, the front cover will not
close.
Close the front cover.
9
Toner replenishment requires 2 to 3 minutes.
NOTE
If the Add Toner indicator does not turn off 2 to 3 minutes after the
start of toner replenishment, repeat step 6.
3-8
CHAPTER 4 BASIC OPERATIONS
1. Basic copying procedure
1
(English text panel) (Symbol panel)
4-1
1. Warm-up
Turn the main switch ON (|). When warm-up ends, the Start indicator
lights.
* If you set an original and press the Start key before warm-up ends,
copying automatically starts at the end of warm-up.
(English text panel) (Symbol panel)
2
2. Function selection
Set copy functions as desired.
(English text panel) (Symbol panel)
3
4. Copy quality selection
Copy quality can be selected according to the original type. Press the
image mode selection key to light the respective indicators.
To adjust automatically: Auto Exp. indicator
Text and photo originals: Text & Photo indicator
Photo originals: Photo indicator
Text originals: Text indicator
* The copy exposure can be adjusted in all image modes (see "Auto
exposure adjustment", "Text and photo original exposure
adjustment", "Text original exposure adjustment" and "Photo original
exposure adjustment" on pages 6-1 and 6-2).
* The image mode used in the initial mode can be selected (see
"Image mode" on page 6-1).
(English text panel) (Symbol panel)
4-2
When the Auto Exp., Text & Photo, Photo and Text indicators are all
turned off, the copier is in the economy mode. In the economy mode,
the image density becomes lighter to reduce toner consumption. Use
this mode when high quality printing is not required.
3. Paper size selection
Select the paper source that contains the paper to be used from the
upper drawer, lower drawer (optional) and multi-bypass using the
Paper Select key.
* The drawer to be selected by default can be specified (see "Default
drawer" on page 6-2).
4-1
5
CHAPTER 4 BASIC OPERATIONS
4-2
CHAPTER 4 BASIC OPERATIONS
2. Enlargement/reduction
(1) Zoom copy
The zoom ratio can be set to any value from 50 to 200% in 1%
increments.
Press the Zoom Input/Enter key. The zoom ratio appears on
1
the copy magnification display, with "%" lit.
(English text panel) (Symbol panel)
(2) Standard zoom copy
Copying is possible using the ratios preset in the copier.
Available ratios
(Inch specifications)
200%:
129%: 5 1/2" x 8 1/2" P 8 1/2" x 11"
100%: Initial setting
78%: 8 1/2" x 14" P 8 1/2" x 11"
50%:
(Metric specifications)
200%:
141%: A5 P A4
100%: Initial setting
70%: A4 P A5
50%:
Press the Size Select key. The zoom ratio appears on the
1
copy magnification display, with "%" lit.
(Inch specifications) (Metric specifications)
Change the displayed zoom ratio using the Number of
2
Copies/Zoom (+) key or Number of Copies/Zoom (-) key.
(English text panel) (Symbol panel)
Press the Zoom Input/Enter key. The zoom ratio will be set
3
and the display indication changes from the magnification to
the number of copies.
(English text panel) (Symbol panel)
Each time you press the Size Select key, the standard zoom
2
ratios appear on the copy magnification display in order.
Display the desired zoom ratio.
(English text panel) (Symbol panel)
Press the Zoom Input/Enter key. The zoom ratio will be set
3
and the display indication changes from the magnification to
the number of copies.
4-3
3. Energy saver (auto preheat) function
CHAPTER 4 BASIC OPERATIONS
This function automatically puts the copier in the sleep mode if no
copying operation is performed for a certain period of time (5 to 45
minutes). In sleep mode, “---” is displayed on the copy quantity/
magnification display and all other indicators are turned off.
* To resume copying after the energy saver (auto preheat) function
has been activated, press any of the operation section keys. The
length of time that the copier uses to recover from the energy saver
(auto preheat) function can be selected between within 10 seconds
(priority to recovery) and within 30 seconds (priority to power save).
(See “Auto preheat time” on page 6-4 and “Preheat recovery time”
on page 6-5.)
(English text panel) (Symbol panel)
4. Auto shut-off function
This function automatically turns the main switch OFF (O) if no
copying operation is preformed for a certain period of time (15 to 120
minutes). To make copies again, set the main switch to the ON (|)
position.
* If the optional printer board is installed, copying will be enabled
when any of the operation keys is pressed or data is received from
the computer.
● Auto shut-off function
The auto shut-off function is a power-saving feature which
automatically turns OFF (O) the main switch when a certain time
elapses without copying being performed. Copiers are generally in the
standby mode more than operation mode, and power consumption in
the standby mode occupies a large part of overall consumption.
Having the copier turn OFF (O) automatically reduces unnecessary
power consumption in the standby mode or at night when the copier
is left on. The result is a lower electricity bill.
* To change the time until the auto shut-off function starts, see “Auto
shut-off time” on page 6-4. To cancel the auto shut-off function, see
“Auto shut-off” on page 6-4.
4-4
CHAPTER 5 FUNCTIONS
1. Layout copying
Two or four originals can be combined into a single copy.
The borderline of each original can also be marked with a solid line or
dotted line.
* The 15 ppm copier requires the optional memory copy board to
perform layout copying.
* The default borderline can be set (see “Layout (borderline)” on page
6-4).
* The original and copy paper must be a standard size.
● 2 in 1
Use this mode to copy two originals onto one sheet.
(When scanning the originals individually, originals are arranged in the
order of 1 and 2.)
Setting originals
(18 ppm copier)
Original
P
L
(15 ppm copier)
Original
Original setting location
DF Platen
P
L
Original setting location
DF Platen
P
L
P
L
P
L
P
L
5-1
CHAPTER 5 FUNCTIONS
● 4 in 1
Use this mode to copy four originals onto one sheet.
(When scanning the originals individually, originals are arranged in the
order of 1, 2, 3 and then 4.)
* In the 4 in 1 mode, the page arrangement can be selected (see
"Layout (4 in 1)" on page 6-3).
Setting originals
(18 ppm copier)
Original
Original setting location
DF Platen
To change the type of the borderline, hold down the 2 in 1/4
1
in 1 key for 5 seconds. “F17” appears on the copy quantity
display and then a number appears. The number displayed
indicates the type of the borderline as follows:
1: None
2: Solid line
3: Dotted line
(English text panel) (Symbol panel)
Press the Number of Copies/Zoom (+) key or Number of
2
Copies/Zoom (-) key and change the number to select the
type of the borderline.
(English text panel) (Symbol panel)
P
L
(15 ppm copier)
Original
P
P
P
L
Original setting location
DF Platen
P
P
L
Press the Zoom Input/Enter key. The number of copies
3
appears on the display.
(English text panel) (Symbol panel)
L
L
L
5-2
CHAPTER 5 FUNCTIONS
Press the 2 in 1/4 in 1 key to light the 2 in 1 indicator or 4 in 1
4
indicator.
(English text panel) (Symbol panel)
Set the originals.
5
*Before setting originals on the platen, make sure they are in
the correct sequence.
*With the 15 ppm copier, if “ON” is selected for “DF auto
start”, scanning starts automatically when an original is set
in the DF (see page 6-3). Proceed to step 7.
When scanning of the first original ends, “1” (number of
7
scanned originals) appears on the display. Place the next
original. When using the platen, press the Start key. Repeat
the same procedure for all the originals.
(English text panel) (Symbol panel)
When scanning of all the originals ends, press the Zoom
8
Input/Enter key or 2 in 1/4 in 1 key. Copying will start.
(English text panel) (Symbol panel)
Press the Start key.
6
*If originals are set in the DF on the 18 ppm copier, originals
are scanned one by one and copied.
(English text panel) (Symbol panel)
5-3
2. Sort copying
CHAPTER 5 FUNCTIONS
Copies can be sorted into the required number of sets by storing
original images in the memory before performing copying.
* The 15 ppm copier requires the optional memory copy board to
perform sort copying.
Press the Sort key to light the indicator.
1
*With the 18 ppm copier, the Sort indicator automatically
turns on when originals are set in the DF.
(English text panel) (Symbol panel)
Press the Start key.
4
*If originals are set in the DF on the 18 ppm copier, originals
are scanned one by one and copied.
(English text panel) (Symbol panel)
When scanning of the first original ends, “1” (number of
5
scanned originals) appears on the display. Place the next
original. When using the platen, press the Start key. Repeat
the same procedure for all the originals.
(English text panel) (Symbol panel)
Set the number of copies to be made.
2
Set the originals.
3
*When using the platen, make sure that the originals are in
the correct sequence.
*With the 15 ppm copier, if “ON” is selected for “DF auto
start”, scanning starts automatically when an original is set
in the DF (see page 6-3). Proceed to step 5.
When scanning of all the originals ends, press the Zoom
6
Input/Enter key or Sort key. Copying will start.
(English text panel) (Symbol panel)
5-4
CHAPTER 6 COPIER DEFAULT SETTING
1. Default settings
The state the copier is in at the end of warm-up or when the Reset key is pressed is called the initial mode, and the function settings that are
automatically set for the initial mode are called the default settings. The default settings can be changed according to how you wish to use the
copier.
Setting codes are provided for the default setting items that have selection items. Only the number of the setting code appears on the copy quantity
display. See the “Setting code” column in the table below for the meanings of those numbers. Initial settings are indicated with an asterisk (*).
Default code
F01
F02
F03
F04
F05
Setting item
User status report
Image mode
Exposure steps
Auto exposure adjustment
Text and photo original exposure
adjustment
Setting contents
Prints the details of the default settings.
Selects the image mode at power-on.
Changes the number of exposure steps for the manual
exposure mode.
Adjusts the overall exposure when using the auto
exposure mode. The larger the setting code number, the
darker the copy density.
Adjusts the exposure for when text and photo original is
selected for the image mode. The larger the setting code
number, the darker the copy density.
Setting code
1: Auto Exposure
2: Text & Photo*
3: Photo
4: Text
1: 3 steps*
2: 5 steps
1: 1 Light
2: 2
3: 3*
4: 4
5: 5 Dark
1: 1 Light
2: 2
3: 3*
4: 4
5: 5 Dark
6-1
CHAPTER 6 COPIER DEFAULT SETTING
Default code
F06
F07
F08
F09
Setting item
Photo original exposure
adjustment
Text original exposure
adjustment
Default drawer
Automatic drawer switching
Setting contents
Adjusts the exposure for when photo original is selected
for the image mode. The larger the setting code number,
the darker the copy density.
Adjusts the exposure for when text original is selected
for the image mode. The larger the setting code number,
the darker the copy density.
Specifies the paper feed drawer to be selected
automatically when warm-up ends or when the Reset
key is pressed.
* This setting item will not be displayed if the optional
drawer is not installed.
Sets whether or not to use the automatic drawer
switching function (see page 2-4).
* This setting item will not be displayed if the optional
drawer is not installed.
Setting code
1: 1 Light
2: 2
3: 3*
4: 4
5: 5 Dark
1: 1 Light
2: 2
3: 3*
4: 4
5: 5 Dark
1: Upper drawer*
2: Lower drawer
1: ON*
2: OFF
F10
Upper drawer paper size
Sets the size of paper loaded in the upper drawer.
(Inch)
1: 8 1/2" x 14"
2: 8 1/2" x 11"
3: 5 1/2" x 8 1/2"
(Metric)
1: A4
2: A5
3: Folio
6-2
CHAPTER 6 COPIER DEFAULT SETTING
Default code
F11
F12
F13
Setting item
Lower drawer paper size
(optional)
Turning multi-bypass nonstandard size paper setting ON/
OFF
Non-standard size paper width
setting for multi-bypass
Setting contents
Sets the size of paper loaded in the lower drawer.
* This setting item will not be displayed if the optional
drawer is not installed.
Set to “ON” when using non-standard size paper with
the multi-bypass.
Sets the paper width for the multi-bypass to use non
standard size paper.
* The maximum paper length is 14"/355.6 mm.
* This setting item will not be displayed if “OFF” is
selected in “Turning multi-bypass non-standard size
paper setting ON/OFF”.
Setting code
(Inch)
1: 8 1/2" x 14"
2: 8 1/2" x 11"
3: 5 1/2" x 8 1/2"
(Metric)
1: A4
2: A5
3: Folio
1: ON
2: OFF*
(Inch)
4.13" to 8.50" (4.13" *)
(Metric)
105 to 216 mm (105 mm*)
* The maximum width of the
print area is 210 mm, with
respect to the paper
centerline.
F14
F15
F16
Copy limit
DF auto start
Layout (4 in 1)
Limits the number of copies that can be made at a time.
Set to “OFF” when not wanting copies to be made
automatically when an original is placed in the DF.
* This setting item is not displayed on the 18 ppm copier.
When using the 4 in 1 layout copying function (see page
5-1), the page arrangement can be selected.
1 Originals of landscape orientation
Original insertion direction
2 Originals of portrait orientation
Original insertion direction
1 to 99 copies (99 copies*)
1: ON*
2: OFF
1: Landscape
2: Portrait*
6-3
* With the 15 ppm copier, this setting item will not be
displayed if the optional memory copy board is not
installed.
CHAPTER 6 COPIER DEFAULT SETTING
Default code
F17
F18
F19
Setting item
Layout (borderline)
Silent mode
Auto shut-off
Setting contents
Selects the type of borderline for layout copying (see
page 5-1).
* With the 15 ppm copier, this setting item will not be
displayed if the optional memory copy board is not
installed.
Selects the length of time from when copying ends to
when entering the silent mode, which stops the motors
inside the copier. When “0 seconds” is selected, the
motors stop immediately after copying has been
finished.
Turns the auto shut-off function (page 4-4) ON or OFF.
The auto shut-off function automatically turns the main
switch OFF if copying is not performed for a certain
period of time.
* If auto shut-off interferes with your copying operations,
turn this function OFF. It is recommended to set a
longer interval for triggering the auto shut-off rather
than turn it OFF.
Setting code
1: None*
2: Solid line
3: Dotted line
1: 0 seconds
2: 5 seconds
3: 10 seconds*
4: 15 seconds
5: 30 seconds
1: ON*
2: OFF
F20
F21
Auto preheat time
Auto shut-off time
Selects the length of time from when copying ends to
when the energy saver (auto preheat) function (page
4-4) is triggered.
Selects the length of time from when the copier is not
used to when the auto shut-off function (page 4-4) turns
the main switch OFF automatically. The auto shut-off
function can also be turned OFF. If turned OFF, this
setting cannot be made (see “Auto shut-off”).
* This setting item will not be displayed if “OFF” is
selected for “Auto shut-off”.
* It is recommended to set a long period of time to
trigger the auto shut-off if the copier is used frequently,
and set a short period of time if the copier is used only
occasionally.
* For how to cancel the auto shut-off function, see “Auto
shut-off”.
1: 5 minutes
2: 10 minutes
3: 15 minutes*
4: 20 minutes
5: 25 minutes
6: 30 minutes
7: 35 minutes
8: 40 minutes
9: 45 minutes
1: 15 minutes
2: 30 minutes*
3: 45 minutes
4: 60 minutes
5: 75 minutes
6: 90 minutes
7: 105 minutes
8: 120 minutes
6-4
CHAPTER 6 COPIER DEFAULT SETTING
Default code
F22
F23
F24
Setting item
Preheat recovery time
Viewing total counter value
Toner counter report
Setting contents
Selects the mode of the energy saver (auto preheat)
function (page 4-4) from the recovery priority mode and
power save priority mode. The length of time that the
copier uses to recover from the energy saver (auto
preheat) function can be selected between within 10
seconds (recovery priority mode) and within 30 seconds
(power save priority mode).
Displays the total number of copies made.
The total number of copies are displayed on the copy
quantity display three digits at a time.
Example
When the total number of copies is 1,234
“---” R “001” R “234”
* The total counter value can also be checked in the
following way:
1 Hold down the Stop/Reset key for 5 seconds.
2 The total counter value is displayed.
Prints a report on the toner consumption ratio.
Using this toner consumption ratio, you can manage
when the toner container needs replacing. If the toner
consumption ratio is very high, it is recommended to
combine the use of the economy mode (page 4-1) with
the regular use.
Setting code
1: Recovery priority mode
2: Power save priority
mode*
F25
F26
Toner replacement message
output setting
Paper feed shifting adjustment
(upper drawer)
When the toner is used up and toner container
replacement is required, a message requesting the user
to replace the toner container will be printed. Select
“OFF” when not printing the message.
Adjusts displacement of the copy image.
1: ON*
2: OFF
-3.0 to 3.0 (0*) in increments
of 0.1
6-5
CHAPTER 6 COPIER DEFAULT SETTING
Default code
F27
F28
F29
F30
Setting item
Paper feed shifting adjustment
(lower drawer)
Paper feed shifting adjustment
(multi-bypass)
Inch/metric specifications setting
Folio length setting (drawer)
Setting contents
Adjusts displacement of the copy image.
* This setting item will not be displayed if the optional
drawer is not installed.
Adjusts displacement of the copy image.
* Be sure to use 8 1/2" x 11" (letter)/A4 paper.
Switches the copier specifications setting between inch
and metric.
* Since the specifications setting is made at the factory,
it is not necessary to make this setting under normal
circumstances.
* If "A" and "011" alternate on the copy quantity display,
the copier initializes the data to remedy an error. If this
occurs, make the specifications setting.
When folio is selected as the paper size, this sets the
length of folio.
* This setting item is available only when metric is
selected for the copier specifications.
Setting code
-3.0 to 3.0 (0*) in increments
of 0.1
-3.0 to 3.0 (0*) in increments
of 0.1
1: Inch
2: Metric
3: Metric (Japan)
1: 210 mm*
2: 216 mm
F31
Folio length setting (bypass)
When folio is used, this sets the length of folio.
* This setting item is available only when metric is
selected for the copier specifications.
200 to 216 mm (210 mm*)
6-6
CHAPTER 6 COPIER DEFAULT SETTING
2. How to make default settings
Hold down both of the copy exposure adjustment keys for 3
1
seconds. "F00" (default code) appears on the copy quantity
display.
(English text panel) (Symbol panel)
The default code changes each time the Number of Copies/
2
Zoom (+) key or Number of Copies/Zoom (-) key is pressed.
Select a default code by referring to the table shown in "1.
Default settings".
(English text panel) (Symbol panel)
When the report is printed out, the display returns to that for
4
step 2. To make other settings, perform the respective
procedures (see below). To end the making of default
settings, proceed to step 17.
Enter the paper width by pressing the Number of Copies/
5
Zoom (+) key or Number of Copies/Zoom (-) key. The paper
width can be set from 4.13" to 8.50" (105 to 216 mm).
(Inch specifications) (Metric specifications)
Press the Zoom Input/Enter key. The display returns to that
6
for step 2. To end the making of default settings, proceed to
step 17.
Press the Zoom Input/Enter key.
3
If "F01" or "F24" is selected, a report will be printed out.
Proceed to step 4.
If "F13" is selected, proceed to step 5.
If "F14" is selected, proceed to step 7.
If "F26", "F27" or "F28" is selected, proceed to step 9.
If "F31" is selected, proceed to step 13.
If a code other than the above is selected, proceed to step
15.
(English text panel) (Symbol panel)
Enter the copy limit (99 copies or lower) by pressing the
7
Number of Copies/Zoom (+) key or Number of Copies/Zoom
(-) key.
(English text panel) (Symbol panel)
Press the Zoom Input/Enter key. The display returns to that
8
for step 2. To end the making of default settings, proceed to
step 17.
6-7
CHAPTER 6 COPIER DEFAULT SETTING
Press the Start key. The image pattern shown in the
9
illustration will be printed out.
* When adjusting paper feed shifting of the multi-bypass, be
sure to use 8 1/2" x 11" (letter)/A4 paper.
Image center
Fold the paper precisely into two to obtain the center line of
10
the paper and then compare it with the center line of the
image.
Adjust the value using the Number of Copies/Zoom (+) key
11
or Number of Copies/Zoom (-) key. Adjustment can be made
between -3.0 and 3.0 (changing the value by 0.1 moves the
image center line by 0.1 mm).
Press the Zoom Input/Enter key. The display returns to that
14
for step 2. To end the making of default settings, proceed to
step 17.
The setting code changes each time the Number of Copies/
15
Zoom (+) key or Number of Copies/Zoom (-) key is pressed.
Select a setting code by referring to the table shown in “1.
Default settings”.
(English text panel) (Symbol panel)
Press the Zoom Input/Enter key. The display returns to that
16
for step 2. To end the making of default settings, proceed to
the next step.
+
1
–
2
If the image looks like 1, increase the value.
If the image looks like 2, decrease the value.
Press the Zoom Input/Enter key. The display returns to that
12
for step 2. To end the making of default settings, proceed to
step 17.
Set the length of folio (200 to 216 mm) by pressing the
13
Number of Copies/Zoom (+) key or Number of Copies/Zoom
(-) key.
(English text panel) (Symbol panel)
Press the Stop/Reset key. The display indication changes
17
from the default code to the number of copies.
(English text panel) (Symbol panel)
* You can also end the making of default settings by pressing
the Zoom Input/Enter key when “F00” is displayed.
6-8
CHAPTER 7 WHEN A PROBLEM OCCURS
1. Error display
When any of the indications listed in the table below appears on the operation panel, take the corrective action as instructed.
Indication
“A” and “100” alternate on the copy quantity
display.
“C” and “610”, “620”, “630” or “710” alternate
on the copy quantity display.
“A” and “310”, “400” or “401” alternate on the
copy quantity display.
Action
Turn the main switch OFF and ON and check that the lamp under the platen
turns on during copying.
If the lamp turns on, leave the power turned on for approximately 1 hour. If the
same indication appears again, contact your service representative.
If the lamp does not turn on, contact your service representative.
Contact your service representative.
Turn the main switch OFF and ON. If the same indication appears again, contact
your service representative.
Page
––
––
––
7-1
CHAPTER 7 WHEN A PROBLEM OCCURS
Indication
“A” and “011” alternate on the copy quantity
display.
“A” and “040”, “041” or “043” alternate on the
copy quantity display.
The Add Toner indicator flashes.
Action
An error message will automatically be printed out. Turn the main switch OFF
and ON.
If this indication appears, the copier initializes the data to remedy the error. Make
the specifications setting (F29 Inch/metric specifications setting) before using the
copier again.
If the same indication appears again, print a user status report and contact your
service representative with the details on the report.
The error message is as follows:
“Default data was initialized. Need initial setting to use the machine. Input F29:
User Code. cf. User manual.”
When you installed the memory copy board/DIMM, it was not installed correctly.
Check the installation of the memory copy board/DIMM and turn the main switch
OFF and ON. If the same indication appears when the memory copy board/
DIMM is installed correctly, remove the memory copy board/DIMM, print a user
status report and contact your service representative with the details on the
report.
Copying is still possible for some time with the indicator flashing but it will
eventually be disabled. Replace the toner container and waste toner tank as
soon as possible.
Page
6-6
6-7
6-1
6-7
3-7
“AP” appears on the copy quantity display.
“PF” appears on the copy quantity display.
“E07” appears on the copy quantity display.
“E30” appears on the copy quantity display.
Toner is being replenished inside the copier. Wait a few minutes.
* Although the lamp under the platen may remain lit while “AP” is displayed, it is
not a problem.
• A paper misfeed occurred in the drawer of the flashing indicator. Remove the
misfed paper.
• The drawer of the flashing indicator is not inserted correctly. Close the drawer
securely.
• There is no paper in the drawer of the flashing indicator. Load paper.
The set paper size is different from that of the paper used. Check the paper size
setting and the actual paper size, and set the paper size to the size of the actual
paper or use a paper of the set size.
Installation may not have been performed correctly. Install the copier again by
referring to the installation manual.
––
7-4
3-1
3-3
6-2
6-3
6-7
––
7-2
CHAPTER 7 WHEN A PROBLEM OCCURS
Indication
“E70” appears on the copy quantity display.
“E71” appears on the copy quantity display.
“E72” appears on the copy quantity display.
“E90” appears on the copy quantity display.
Action
While using the DF, the last of the ejected originals failed to be copied. Set that
original back onto the original table and resume the copying operation.
Originals that were not copied can be copied. Set all the ejected originals back
onto the original table and resume the copying operation.
While using the DF, an original is still in the original insertion section. Remove
that original and set it back onto the original table and then resume the copying
operation.
The memory is full.
To make copies of the scanned originals:
Press the Enter key. All the scanned originals will be copied. When copying
ends, set the remaining originals and press the Start key. The copying operation
resumes.
To make copies from the beginning again:
Press the Reset key, reduce the number of originals and repeat copying
operation again.
Page
7-7
7-8
7-7
7-8
7-7
7-8
––
“J98” appears on the copy quantity display.
“OP” appears on the copy quantity display.
“OP1” appears on the copy quantity display.
“OP2” appears on the copy quantity cover.
Open the drawer and left cover and check for any misfed paper. If the same
indication appears, contact your service representative.
The front or left cover is open. Close the cover.
The DF original switchback cover is open. Close the cover.
The left cover of the optional drawer is open. Close the cover.
7-4
––
––
––
7-3
CHAPTER 7 WHEN A PROBLEM OCCURS
2. When paper misfeeds
If a paper misfeed occurs, copying will stop. An indication signaling a paper misfeed appears on the operation panel and an indicator lights showing
the location of a paper misfeed. Remove the misfed paper by referring to “(3) Removal procedures” on page 7-5, with the main switch in the ON (|)
position.
1
4
23
(1) Misfeed location indications
1 Misfeed in paper feed section (page 7-5)
“PF” appears on the copy quantity display and the upper drawer
indicator, lower drawer indicator or multi-bypass indicator flashes
green.
2 Misfeed in left cover (page 7-5)
“J15”, “J20”, “J22”, “J30”, “J40”, “J50” or “J95” appears on the copy
quantity display and the misfeed indicator lights red.
3 Misfeed in DF (page 7-7)
“J70”, “J72” or “J73” appears on the copy quantity display and the
DF indicator lights red.
* When “E70”, “E71” or “E72” is displayed, see page 7-3.
4 Misfeed in drawer <optional> (page 7-8)
“J15” appears on the copy quantity display and the lower drawer
indicator flashes green.
(2) Cautions
WARNING
High voltage is present in the charger section. Take
sufficient care when working in this area, as there is a
danger of electrical shock.
CAUTION
The copier’s fixing unit is extremely hot. Take sufficient
care when working in this area, as there is a danger of
getting burned.
* When “J98” is displayed, see page 7-3.
* Do not reuse misfed paper.
* If paper is torn during removal, be sure to remove all loose scraps
from inside the copier, or they could cause misfeed later.
* After misfed paper has been removed, warm-up will begin. The
misfeed indicator will turn off and the copier will return to the same
settings prior to the misfeed.
7-4
CHAPTER 7 WHEN A PROBLEM OCCURS
(3) Removal procedures
1 Misfeed in paper feed section
● Misfeed in drawer
If the upper drawer indicator flashes green when the drawer is used, a
misfeed has occurred in the drawer. Remove the misfed paper using
the procedure given below.
NOTE
If a paper misfeed occurs in the lower drawer, remove the misfed
paper using the same procedure.
Open the drawer.
1
Remove the misfed paper while taking care not to tear it.
2
*If the paper should be torn, remove all the scraps from the
inside the copier.
● Misfeed in multi-bypass
If the multi-bypass indicator flashes green when the multi-bypass is
used, a misfeed has occurred in the multi-bypass. Remove the misfed
paper using the procedure given below.
Remove all the paper remaining in the multi-bypass.
1
Check that the indicator showing the location of the paper
2
misfeed has turned off and re-load the paper into the multibypass.
2 Misfeed in left cover
If the misfeed indicator lights red, a misfeed has occurred in the left
cover. Remove the misfed paper using the procedure given below.
Open the multi-bypass.
1
3
7-5
Close the drawer slowly.
*Check that the paper is kept under the claw of the drawer. If
not, reload the paper.
Open the left cover.
2
CHAPTER 7 WHEN A PROBLEM OCCURS
WARNING
High voltage is present in the charger section. Take
sufficient care when working in this area, as there is a
danger of electrical shock.
CAUTION
The copier’s fixing unit is extremely hot. Take sufficient
care when working in this area, as there is a danger of
getting burned.
Holding the green handles, lower the two fixing section
3
release levers.
IMPORTANT
The drum 1 is highly sensitive to light and dirt. Be careful not to
expose it to strong light such as room lighting or to touch the drum
with the hands.
1
Holding the green handle, open the ejection guide.
5
Remove the misfed paper while taking care not to tear it.
4
If the paper is not easy to remove, proceed to the next step.
If the paper is removed successfully, proceed to step 9.
*If the paper should be torn, remove all the scraps from the
inside the copier.
CAUTION
The copier’s fixing unit is extremely hot. Take sufficient
care when working in this area, as there is a danger of
getting burned.
Remove the misfed paper while taking care not to tear it.
6
7-6
CHAPTER 7 WHEN A PROBLEM OCCURS
Close the ejection guide.
7
Lift the fixing section release levers.
8
3 Misfeed in DF
If the DF indicator lights red, a misfeed has occurred in the DF.
Remove the misfed original using the procedure given below.
● 18 ppm copier
Remove all the originals from the original table.
1
Open the DF original switchback cover.
2
NOTE
If the fixing section release levers are lowered, the left cover does not
close.
Close the left cover and multi-bypass.
9
Pull the drawer out and check that no paper is misfed.
10
Close the drawer slowly.
11
Remove the misfed original.
3
Close the DF original switchback cover.
4
Set the misfed original together with those moved back onto
the original table and resume the copying operation.
7-7
● 15 ppm copier
Remove the original on the original table to the right or left,
1
whichever direction that is easier to remove the original.
Place the original on the original table again and resume the
2
copying operation.
4 Misfeed in drawer <optional>
If the lower drawer indicator flashes green, a misfeed has occurred in
the lower drawer. Remove the misfed paper using the procedure
given below.
CHAPTER 7 WHEN A PROBLEM OCCURS
Open the left cover of the optional drawer.
1
Remove the misfed paper while taking care not to tear it.
2
*If the paper should be torn, remove all the scraps from the
inside the copier.
Close the left cover of the optional drawer.
3
7-8
CHAPTER 7 WHEN A PROBLEM OCCURS
3. Troubleshooting
If trouble occurs, carry out the applicable checks and actions given below.
If the trouble persists, print out a user status report and contact your service representative.
Trouble
Nothing lights on the
operation panel when the
main switch is turned ON.
No copies come out when
the Start key is pressed.
Copies come out blank.
Checks
Is the power plug connected to an AC
outlet?
Is there any indication appearing on the
operation panel?
Are the originals set correctly?
Action
Connect the plug to an AC outlet.
Perform the corrective action corresponding
to the indication.
When setting originals on the platen, place
them face-down.
18 ppm copier
When setting originals in the DF, place them
face-up.
15 ppm copier
When setting an original in the DF, place it
face-down.
Page
––
7-1
3-6
3-5
3-6
Copies come out too light.
Is the copier in the auto exposure mode?
Is the copier in the Photo, Text & Photo or
Text mode?
Is the Add Toner indicator lit?
Is paper wet?
To change the overall exposure, perform
auto exposure adjustment.
Adjust the exposure to the correct degree
using the copy exposure adjustment keys.
To change the overall exposure, perform the
exposure adjustment for each mode.
Replace the toner container.
Replace the paper with new paper.
6-1
6-7
4-2
6-1
6-2
6-7
3-7
3-1
7-9
CHAPTER 7 WHEN A PROBLEM OCCURS
Trouble
Copies come out too dark.
Copies are dirty.
Copy image is askew.
Checks
Is the copier in the auto exposure mode?
Is the copier in the Photo, Text & Photo or
Text mode?
Is the platen or the DF dirty?
Are the originals set correctly?
Action
To change the overall exposure, perform
auto exposure adjustment.
Adjust the exposure to the correct degree
using the copy exposure adjustment keys.
To change the overall exposure, perform the
exposure adjustment for each mode.
Clean the platen and/or the DF.
Open the front cover, pull out and push back
in the cleaning shaft.
When setting an original on the platen, be
sure to align a corner of it with the rear left
corner of the platen.
Page
6-1
6-7
4-2
6-1
6-2
6-7
8-1
3-7
3-6
Misfeed occurs frequently.
Is the paper set correctly in the drawer(s)?
Is paper curled, folded or wrinkled?
Is there any misfed paper or loose scraps of
paper remaining inside the copier?
Is the set paper size different from that of the
paper used?
18 ppm copier
When setting originals in the DF, be sure to
adjust the original insertion guides to the
original size.
15 ppm copier
When setting an original in the DF, be sure
to align the original to the rear of the DF. If
copy images become askew when originals
are correctly placed in the DF, make copies
by placing originals on the platen.
Set paper properly.
Replace the paper with new paper.
Carry out the appropriate procedure to
remove the paper.
Set the paper size to the size of the actual
paper, or use a paper of the set size.
3-5
3-6
3-1
3-1
7-4
3-3
6-2
6-3
6-7
The Add Toner indicator
does not turn off after toner
replenishment.
Printing cannot be
preformed from a computer
when the optional printer
board is installed.
Has the new toner container been shaken
sufficiently?
Is the printer board installed correctly?
Shake the toner container again.
Install the printer board correctly.
3-7
––
7-10
CHAPTER 8 CLEANING AND SPECIFICATIONS
1. Cleaning the copier
CAUTION
For safety purposes, ALWAYS remove the power plug from
the outlet when performing cleaning operations.
Lift open the DF. Wipe the shaded areas shown in the below
illustrations with a soft cloth dampened with alcohol or a mild
detergent.
* Never use thinner or other organic solvents for this purpose.
IMPORTANT
15 ppm copier
Do not touch the gear near the rear left corner of the platen. If you do,
your hands may be soiled or injury may result.
* If black lines appear on the copy image when the DF is used, the slit
glass a is soiled.
a
8-1
CHAPTER 8 CLEANING AND SPECIFICATIONS
2. Specifications
Type ............................................................................... Desk-top
Original table .................................................................. Fixed type
Copying system ............................................................. Indirect electrostatic
Originals ......................................................................... DF (18 ppm copier): Sheets of paper (Maximum original size: 8 1/2" x 14"/folio)
DF (15 ppm copier): Sheets of paper (8 1/2" x 11", 8 1/2" x 14"/A4, folio)
Platen: Sheets of paper, books, 3-dimensional objects (Maximum original size: 8 1/2" x 14"/
folio)
Copy sizes ..................................................................... 8 1/2" x 14", 8 1/2" x 11", 5 1/2" x 8 1/2"
A4, A5 (vertical), A6 (vertical), folio
Print margin loss: 0.5 - 5.5 mm
Copying speed ............................................................... Same-size copying 8 1/2" x 11"/A4: 18 copies/min. (18 ppm copier)
15 copies/min. (15 ppm copier)
Warm-up time................................................................. Within 30 seconds (at room temperature of 68°F/20°C, humidity 65%RH)
From energy saver (auto preheat) mode: Within 10 seconds [priority to recovery], within 30
seconds [priority to power save] (at room temperature of 68°F/20°C, humidity 65%RH)
First copy speed............................................................. Approximately 6.3 seconds (8 1/2" x 11"/A4, original placed on the platen)
Zoom ratios .................................................................... Any ratio between 50 and 200% (in increments of 1%)
Memory .......................................................................... 16 MB (optional for the 15 ppm copier)
Image storage memory: 11.5 MB (approximately 30 8 1/2" x 11"/A4 originals of 6% black
coverage can be saved)
Bitmap memory: 4.5 MB
Resolution ...................................................................... Reading: 600 x 600 dpi
Writing: 600 x 600 dpi
Paper feed system ......................................................... Automatic feeding from the drawer
(1 drawer, capacity 250 sheets [80 g/m2/standard paper as specified by our company]) and
multi-bypass (capacity 50 sheets [80 g/m2/standard paper as specified by our company])
Copy paper .................................................................... Drawer: Standard paper (64 - 80 g/m2)
Multi-bypass: Standard paper (60 - 160 g/m2), special paper (colored paper, letterhead,
etc.), envelopes (COM-10, Monarch, DL, C5) [when using the printer function only]
Continuous copying ....................................................... 1 - 99 sheets
Light source ................................................................... Rare gas lamp
Developing system......................................................... 2-componet, reverse developing
Fixing system ................................................................. Heat roller
Cleaning system ............................................................ Blade
Photoconductor .............................................................. OPC
Functions and modes..................................................... Auto exposure adjustment, photo mode, economy mode, zoom copy mode, standard zoom
mode, auto shut-off function, energy saver (auto preheat) function, self-diagnosis function,
layout copying*, sort copying*
* The 15 ppm copier requires the optional memory copy board.
Power source ................................................................. 120 V AC, 60 Hz, 9 A
220 - 240 V AC, 50/60 Hz, 4.8 A (average 2.5 A)
Dimensions .................................................................... 18 ppm copier: 19 9/16" (W) x 19 9/16" (D) x 17 1/2" (H)
497 mm (W) x 497 mm (D) x 445 mm (H)
15 ppm copier: 19 9/16" (W) x 19 9/16" (D) x 14 13/16" (H)
497 mm (W) x 497 mm (D) x 376 mm (H)
Weight ............................................................................ 18 ppm copier: Approx. 59.4 lbs (27 kg)
15 ppm copier: Approx. 55 lbs (25 kg)
Noise emission............................................................... 70 dB (A)
Required space .............................................................. 19 9/16" (W) x 19 9/16" (D)
497 mm (W) x 497 mm (D)
Optional equipment ........................................................ Drawer, memory copy board (standard for the 18 ppm copier), printer board, printer network
board
(Specifications are subject to change without notice.)
8-2
Laser Safety
Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine is hermetically
sealed within the protective housing and external cover. In the normal operation of the product by user, no radiation can leak from the
machine.
This machine is classified as Class 1 laser product under IEC 825.
CAUTION
Performance of procedures other than those specified in this manual may result in hazardous radiation exposure.
This label is attached to the laser scanner unit inside the machine and is not in a user access area.
The labels shown below are attached on the rear side of the machine.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
CAUTION!
The power plug is the main isolation device! Other switches on the equipment are only
functional switches and are not suitable for isolating the equipment from the power source.
VORSICHT!
Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gerät sind
nur Funktionsschalter und können nicht verwendet werden, um den Stromfluß im Gerät
zu unterbrechen.
WARNING
This is Class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
* The above warning is valid only in Australia and New Zealand.
DECLARATION OF CONFORMITY
89/336/EEC, 73/23/EEC and 93/68/EEC
We declare under our sole responsibility that the product to which
this declaration relates is in conformity with the following specifications.
Limits and methods of measurement for immunity
characteristics of information technology equipment
Limits and methods of measurement for radio interference
characteristics of information technology equipment
Limits for harmonic currents emissions
for equipment input current
Limitation of voltage fluctuations and flicker in low-voltage
supply systems for equipment with rated current
Safety of information technology equipment,
including electrical equipment
Radiation Safety of laser products, equipment classification,
requirements and user's guide
16A per phase EN61000-3-2
16A EN61000-3-3
TO
EN55024
EN55022 Class B
EN60950
EN60825-1
E1
Loading...