Triumph-Adler DC2060, DC2080 Basic Manual

Instruction Handbook

Basic

DC 2060 | 2080

Digital Multifunctional

System

This Operation Guide is for models DC 2060 and DC 2080. In this guide, DC 2060 refers to the
60 cpm (copies per minute) model and DC 2080 to the 80 cpm model.

NOTE: This Operation Guide contains information that corresponds to using both the inch and
metric versions of these copiers.

The inch versions of these copiers are shown in the screens in this guide. If you are using the
metric version, use the messages provided for the inch version as reference only. In the body
text, only the inch messages are given if these versions differ only in capitalization. When there
is even a slight difference in the message, we have listed the information for the inch version
followed, in brackets, by the corresponding information for the metric version.

Take Advantage of Advanced Functions

For information on basic copying, refer to Chapter 3 of the Operation Guide.

Selecting Image Quality

Enjoy crisp, high-quality copies, even
of photographs.

Manual Zoom

Reduce or enlarge original images by
25 to 400 % (25-200 % with the
document processor).

25 %

400 %

Adjusting Exposure

Freely adjustable copy exposure
level.

Preset Zoom

One-touch selection of
magnifications.

70%
75%

90%
106%
127%
141%
200%

50%
64%
77%

78%
121%
129%
154%
200%

Auto Zoom

Reduce or enlarge original images to
fit your selected paper size.

11 × 17": 129 %

1/2 × 11"

8

A3: 141 %
5

A4

1/2 ×81/2": 64 %

A5: 70 %

XY Zoom

Select vertical and horizontal
magnification individually.

Height

Width

Duplex Mode

Create two-sided copies
automatically from any kind of
original.

5

4

3

2

1

2

Split Mode

Copy double-sided or two-page
originals onto separate sheets

Sort Mode

Make separate sets in the quantity of
your choice.

automatically.

5

3

4

1

21

1

2

1

1

2

2

3

2

1

3

2

1

3

2

1

3

2

1

i

Read more about these sophisticated functions in Chapter 1 of the Advanced Operation Guide.

Auto Paper Selection

Automatic selection of paper to
match the original.

Margin Mode

Set up blank margin or gutter space
for your binding needs.

Page Numbering

Print sequential page numbers on the
copies.

Offset Mode

Handy option to stack sets in
alternating orientations.

3

3

2

1

2

1

3

2

1

1

Centering Originals

Customize output by centering the
image on the page.

Cover Mode

Use a distinctive front and/or back
cover.

Combine Mode

Combine two or four originals on a
single page.

3

2

Border Erase

Eliminate unnecessary borders on
the original for cleaner output.

Form Overlay

Copy images from separate originals
together onto one sheet.

A

B

C

D

E

A

-1-

-2-

Booklet from Sheets

Create booklets from separate
originals.

B

C

D

E

-3-

-4-

-5-

3

1

4

2

Booklets from Booklets

Reproduce booklets just as they are.

2

1

Memo Mode

Add space for notes next to copied
images.

ii

Batch Scanning

Copy high-volume originals in a
single copy job.

200

100

1

Proof Mode

Copy a test sheet before a
high-volume job.

2

1

1

3

2

1

2

1

Repeat Copy

Produce more copies as needed after
making the initial copies.

3

3

Backing Sheets for Transparencies

Use paper as backing sheets when
printing transparencies for projectors.

Inverted Copying

Invert both black and white and color
images.

Multi-Page Forms

Great for bound originals made up of
several sheets.

Auto Rotation

Automatically match the orientation of
originals.

Mirror Image

Create mirror images of originals.

Programmed Copying

Store commonly used settings.

EcoPrint (Economy Printing) Mode

Use toner more efficiently as
necessary.

Auto Selection Mode

Easily handle originals of different
sizes.

iii

Programming Multi-Part Jobs

Simply specify your series of special
copying needs-such as cover pages,
internal cover pages...

7

8

5

6

3

4

1

2

and zooming or border erase for
particular pages...

3

21

4

load the originals, and voila!
Automated copying of your detailed
jobs.

7

5

2

8

5

6

3

4

1

Read more about these handy document/output management functions in Chapter 2 of the Advanced Operation
Guide.

Form Box

Add and manage graphics for
compositing.

Shared Data Box

Easily store commonly used
documents...

Synergy Print Box

Just add common documents... to make them instantly available later

in combination with other copying
jobs.

to produce them later as needed
without the original.

Output Management

Control and modify the copying order
of originals

1
2
3
4

1
4
3
2

iv

Features for Easier Copying

Job Accounting Mode: Refer to

Chapter 3 of the Advanced Operation
Guide.

Use department codes to manage
total copy volume.

Weekly Timer: Refer to Chapter 3 of
the Advanced Operation Guide.

Auto Power on/off.

Language Setting: Refer to
Selecting the Language on
page 2-20.

Choose the correct message display
language.

DeutschEnglish

OFF

A B C

ON

Read about our full line of useful Optional Equipment on page 4-1.

Side Feeder Document Finisher (When equipped with a multi-job tray

and folding unit)

Key Counter Printer Kit Scanner Kit

Security Kit

v

vi

Legal and Safety Information

Please read this information before using your copier. This chapter provides information on the
following topics:

• Legal Information...viii

• Energy Star Program...ix

• Safety Conventions in This Guide...x

• Caution Labels...xii

• Installation Precautions...xiii

• Precautions for Use...xiv

vii

Energy Star Program

We have determined as a participating company in the International Energy Star Program that
this product is compliant with the standards laid out in the International Energy Star Program.

About the International Energy Star Program

International Energy Star Program has as its basic goals the promotion of efficient energy use
and the reduction of the environmental pollution that accompanies energy consumption by
promoting the manufacture and sale of products that fulfill program standards.

International Energy Star Program standards require that copies come equipped with a Low
Power Mode where energy consumption is reduced after a certain amount of time elapses since
the device was last used, as well as an Off Mode where the device automatically turns itself off
after there is no activity within a set amount of time. When the copier includes printer and fax
functions, the printer and fax must enter a Low Power Mode where power consumption is
automatically reduced after a certain amount of time elapses since they were last used, and they
must also support a Sleep Mode where power consumption is reduced to a minimum when
there is no activity within a set amount of time. This product is equipped with the following
features as a result of its compliance with International Energy Star Program standards.

Low Power Mode

The device automatically enters Low Power Mode when 15 minutes have passed since the
device was last used. The amount of time of no activity that must pass before Low Power Mode
is activated may be lengthened. Refer to Low-Power Mode on page 3-19 for more information.

Off Mode

The device automatically enters Off Mode when 90 minutes have passed since the device was
last used. The amount of time of no activity that must pass before Off Mode is activated may be
lengthened. For more information refer to Sleep Mode on page 3-20.

Sleep Mode (If the copier has printer and/or facsimile function)

The device automatically enters Sleep Mode when 90 minutes have passed since the device
was last used. The amount of time of no activity that must pass before Sleep Mode is activated
may be lengthened. For more information refer to Sleep Mode on page 3-20.

Automatic 2-Sided Copy Function

The Energy Star Program encourages the use of 2-sided copying which reduces the load on the
environment and this device includes 2-sided copying as a standard function. For example, by
copying two 1-sided originals onto a single sheet of paper as a 2-sided copy, it is possible to
lower the amount of paper used. For more information refer to Duplex Mode on page 3-11.

Paper Recycling

The Energy Star Program encourages the use of environmentally friendly recycled paper. Your
sales or service representative can provide information about recommended paper types.

ix

Safety Conventions in This Guide

Please read this Operation Guide before using the copier. Keep it close to the copier for
easy reference.

The sections of this guide and parts of the copier marked with symbols are safety warnings
meant to protect the user, other individuals and surrounding objects, and ensure correct and
safe usage of the copier. The symbols and their meanings are indicated below.

DANGER: Indicates that serious injury or even death will very possibly result
from insufficient attention to or incorrect compliance with the related points.

WARNING: Indicates that serious injury or even death may result from
insufficient attention to or incorrect compliance with the related points.

CAUTION: Indicates that personal injury or mechanical damage may result from
insufficient attention to or incorrect compliance with the related points.

Symbols

The symbol indicates that the related section includes safety warnings. Specific points of
attention are indicated inside the symbol.

.... [General warning]

.... [Warning of danger of electrical shock]

.... [Warning of high temperature]

The symbol indicates that the related section includes information on prohibited actions.
Specifics of the prohibited action are indicated inside the symbol.

.... [Warning of prohibited action]

.... [Disassembly prohibited]

x

The z symbol indicates that the related section includes information on actions which must be
performed. Specifics of the required action are indicated inside the symbol.

.... [Alert of required action]

.... [Remove the power plug from the outlet]

.... [Always connect the machine to an outlet with a ground connection]

Please contact your service representative to order a replacement if the safety warnings in this
Operation Guide are illegible or if the guide itself is missing. (fee required)

xi

Caution Labels

Caution labels have been attached to the copier at the following locations for safety purposes.
Be sufficiently careful to avoid fire or electric shock when removing a paper jam or when
replacing toner.

Label 1, 2

High temperature inside. Do not
touch parts in this area, because
there is a danger of getting burned.

Label 3

High voltage inside. Never touch parts
in this area, because there is a danger
of electric shock.

Label 8, 9

Do not touch the support area for the document
processor as there is a danger that your fingers
or other objects may become caught or pinched,
and this can result in injury.

Label 4, 10

High temperature inside. Do not touch
parts in this area, because there is a
danger of getting burned.

Label 5, 6, 7

High temperature inside. Do not touch parts in this area, because there is a danger of getting burned.

NOTE: Do not remove these labels.

xii

Installation Precautions

Environment

Caution

Avoid placing the copier on or in locations which are unstable or not level. Such
locations may cause the copier to fall down or fall over. This type of situation presents
a danger of personal injury or damage to the copier.

Avoid locations with humidity or dust and dirt. If dust or dirt become attached to the
power plug, clean the plug to avoid the danger of fire or electrical shock.

Avoid locations near radiators, heaters, or other heat sources, or locations near
flammable items, to avoid the danger of fire.

To keep the copier cool and facilitate changing of parts and maintenance, allow
access space as shown below. Leave adequate space, especially around the rear
cover, to allow air to be properly ventilated out of the copier.

3 15/16"
10 cm

23 5/8"
60 cm

39 3/8"
100 cm

Always use the caster stoppers to stabilize the copier once it is in place to keep it
from moving and/or falling over and causing injury.

27 9/16"
70 cm

Other precautions

Adverse environmental conditions may affect the safe operation and performance of
the copier. Install in an air-conditioned room (recommended room temperature: around 73.4 °F
(23 °C), humidity: around 50 %) and avoid the following locations when selecting a site for the
copier.

• Avoid locations near a window or with exposure to direct sunlight.

• Avoid locations with vibrations.

• Avoid locations with drastic temperature fluctuations.

• Avoid locations with direct exposure to hot or cold air.

• Avoid poorly ventilated locations.

xiii

If the floor is delicate against casters, when this product is moved after installation, the floor
material may be damaged.

During copying, some ozone is released, but the amount does not cause any ill effect to one’s
health. If, however, the copier is used over a long period of time in a poorly ventilated room or
when making an extremely large number of copies, the smell may become unpleasant. To
maintain the appropriate environment for copy work, it is suggested that the room be properly
ventilated.

Power supply/Grounding the copier

Warning

Do not use a power supply with a voltage other than that specified. Avoid multiple
connections in the same outlet. These types of situations present a danger of fire or
electrical shock.

Plug the power cord securely into the outlet. If metallic objects come in contact with
the prongs on the plug, it may cause a fire or electric shock.

Always connect the copier to an outlet with a ground connection to avoid the danger
of fire or electrical shock in case of an electric short. If an earth connection is not
possible, contact your service representative.

Other precautions

Connect the power plug to the closest outlet possible to the copier.

The power supply cord is used as the main disconnect device. Ensure that the socket/outlet is
located/installed near the equipment and is easily accessible.

Handling of plastic bags

Warning

Keep the plastic bags that are used with the copier away from children. The plastic
may cling to their nose and mouth causing suffocation.

Precautions for Use

Cautions when using the copier

Warning

Do not place metallic objects or containers with water (flower vases, flower pots,
cups, etc.) on or near the copier. This of situation presents a danger of fire or
electrical shock should they fall inside.

Do not remove any of the covers from the copier as there is a danger of electrical
shock from high voltage parts inside the copier.

xiv

Do not damage, break or attempt to repair the power cord. Do not place heavy
objects on the cord, pull it, bend it unnecessarily or cause any other type of damage.
These types of situations present a danger of fire or electrical shock.

Never attempt to repair or disassemble the copier or its parts as there is a danger of
fire, electrical shock or damage to the laser. If the laser beam escapes, there is a
danger of it causing blindness.

If the copier becomes excessively hot, smoke appears from the copier, there is an
odd smell, or any other abnormal situation occurs, there is a danger of fire or
electrical shock. Turn the main power switch off ({ position) immediately, be
absolutely certain to remove the power plug from the outlet and then contact your
service representative.

If anything harmful (paper clips, water, other fluids, etc.) falls into the copier, turn the
main power switch off ({ position) immediately. Next, be absolutely certain to remove
the power plug from the outlet to avoid the danger of fire or electrical shock. Then
contact your service representative.

Do not remove or connect the power plug with wet hands, as there is a danger of
electrical shock.

Always contact your service representative for maintenance or repair of internal parts.

Caution

Do not pull the power cord when removing it from the outlet. If the power cord is
pulled, the wires may become broken and there is a danger of fire or electrical shock.
(Always grasp the power plug when removing the power cord from the outlet.)

Always remove the power plug from the outlet when moving the copier. If the power
cord is damaged, there is a danger of fire or electrical shock.

If the copier will not be used for a short period of time (overnight, etc.), turn the main
switch off ({). If it will not be used for an extended period of time (vacations, etc.),
remove the power plug from the outlet for safety purposes during the time the copier
is not in use.

Always hold the designated parts only when lifting or moving the copier.

For safety purposes, always remove the power plug from the outlet when performing
cleaning operations.

If dust accumulates within the copier, there is a danger of fire or other trouble. It is
therefore recommended that you consult with your service representative in regard to
cleaning of internal parts. This is particularly effective if accomplished prior to
seasons of high humidity. Consult with your service representative in regard to the
cost of cleaning the internal parts of the copier.

Do not leave the document processor open as there is a danger of personal injury.

Other precautions

Do not place heavy objects on the copier or cause other damage to the copier.

Do not open the front cover, turn off the main power switch, or pull out the power plug during
copying.

xv

When lifting or moving the copier, contact your service representative.

Do not touch electrical parts, such as connectors or printed circuit boards. They could be
damaged by static electricity.

Do not attempt to perform any operations not explained in this handbook.

Caution: Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.

Do not look directly at the light from the scanning lamp as it may cause your eyes to feel tired or
painful.

This copier comes equipped with an HDD (hard disk). Do not attempt to move the copier while
the power is still on; Since any resulting shock or vibration may cause damage to the hard disk,
be sure to turn off the power before attempting to move the copier.

Cautions when handling consumables

Caution

Do not attempt to incinerate the toner container or the waste toner box. Dangerous
sparks may cause burns.

Keep the toner container and the waste toner box out of the reach of children.

If toner happens to spill from the toner container or the waste toner box, avoid
inhalation and ingestion, as well as contact with your eyes and skin.

• If you do happen to inhale toner, move to a place with fresh air and gargle
thoroughly with a large amount of water. If coughing develops, contact a
physician.

• If you do happen to ingest toner, rinse your mouth out with water and drink 1 or 2 cups of
water to dilute the contents of your stomach. If necessary, contact a physician.

• If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any
remaining tenderness, contact a physician.

• If toner does happen to get on your skin, wash with soap and water.

Do not attempt to force open or destroy the toner container or the waste toner box.

Other precautions

After use, always dispose of the toner container and the waste toner box in
accordance with Federal, State and Local rules and regulations.

If the copier will not be used for an extended period of time, remove the paper from the cassette
and the MP tray (multi-purpose tray), return it to its original package and reseal it.

Don’t store the unit in a place exposed to:

• Direct sunlight

• High or rapidly variable temperature or humidity (limit: 104 °F or 40 °C)

xvi

Laser Safety (Europe)

Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted
inside this machine is hermetically sealed within the protective housing and external cover. In
the normal operation of the product by user, no radiation can leak from the machine.

This machine is classified as Class 1 laser product under IEC 60825.

Caution: Performance of procedures other than those specified in this manual may result in
hazardous radiation exposure.

These labels are attached to the laser scanner unit inside the machine and are not in a user
access area.

The label shown below is attached on the left side of the machine.

xvii

Safety Instructions Regarding the Disconnection of Power

Caution: The power plug is the main isolation device! Other switches on the equipment are only

functional switches and are not suitable for isolating the equipment from the power source.

VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem
Gerät sind nur Funktionsschalter und können nicht verwendet werden, um den Stromfluß im
Gerät zu unterbrechen.

DECLARATION OF CONFORMITY

TO

89/336/EEC, 73/23/EEC and 93/68/EEC

We declare under our sole responsibility that the product to which
this declaration relates is in conformity with the following specifications.

Limits and methods of measurement for immunity
characteristics of information technology equipment EN55024

Limits and methods of measurement for radio interference
characteristics of information technology equipment EN55022 Class B

Limits for harmonic currents emissions
for equipment input current 16A per phase EN61000-3-2

Limitation of voltage fluctuations and flicker in low-voltage
supply systems for equipment with rated current 16A EN61000-3-3

Safety of information technology equipment,
including electrical equipment EN60950

Radiation Safety of laser products, equipment classification,
requirements and user’s guide EN60825-1

xviii

SAFETY OF LASER BEAM (USA)

1. Safety of laser beam

This copier has been certified by the manufacturer to Class 1 level under the radiation
performance standards established by the U.S.DHHS (Department of Health and Human
Services) in 1968. This indicates that the product is safe to use during normal operation and
maintenance. The laser optical system, enclosed in a protective housing and sealed within the
external covers, never permits the laser beam to escape.

2. The CDRH Act

A laser-product-related act was implemented on Aug. 2, 1976, by the Center for Devices and
Radiological Health (CDRH) of the U.S. Food and Drug Administration (FDA). This act prohibits
the sale of laser products in the U.S. without certification, and applies to laser products
manufactured after Aug. 1, 1976. The label shown below indicates compliance with the CDRH
regulations and must be attached to laser products marketed in the United States. On this
copier, the label is on the left.

3. Optical unit

When checking the optical unit, avoid direct exposure to the laser beam, which is invisible.
Shown at below is the label located on the cover of the optical unit.

4. Maintenance

For safety of the service personnel, follow the maintenance instructions in the other section of
this manual.

5. Safety switch

The power to the laser unit is cut off when the upper front cover is opened.

xix

Safety Instructions Regarding the Disconnection of Power

Caution: The power plug is the main isolation device! Other switches on the equipment are only

functional switches and are not suitable for isolating the equipment from the power source.

Attention: Le débranchement de la fiche secteur est le seul moyen de mettre l’appareil hors
tension. Les interrupteurs sur l’appareil ne sont que des interrupteurs de fonctionnement: ils ne
mettent pas l’appareil hors tension.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION — The changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

* The above warning is valid only in the United States of America.

MERCURY WARNING

THE LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

xx

xxii

Introduction

This Operation Guide contains the following chapters:

1Part Names

Identifies copier parts and operation panel keys.

2 Preparing to Copy

Explains how to load paper and originals.

3 Basic Operation

Describes the procedures for basic copying.

4 Optional Equipment

Introduces the convenient optional equipment available for this copier.

5 Maintenance

Describes cleaning and toner replacement.

6 Troubleshooting

Explains how to handle error messages, paper jams, and other problems.

Appendix

Lists the copier specifications.

xxiii

Guides Included

The following guides are included with this copier. Refer to the proper guide for your needs.

Operation Guide (This Guide)

Describes how to load paper, basic copier operations, and troubleshooting.

Advanced Operation Guide

Covers copying details in depth as well as default settings.

Conventions in This Guide

The following conventions are used depending on the nature of the description.

Convention Description Example

Bold Indicates operation panel keys. Press the Start key.

[Regular] Indicates touch panel keys. Press [Basic].

Italic Indicates touch panel messages. Ready to copy is displayed.

NOTE Indicates supplemental information or

operations for reference.

NOTE: -

IMPORTANT Indicates items that are required or

prohibited so as to avoid problems.

IMPORTANT: -

xxiv

Contents

Take Advantage of Advanced Functions ......................................................................................i

Legal and Safety Information ........................................................................................................................ vii

Legal Information ......................................................................................................................viii

Energy Star Program .................................................................................................................. ix

Safety Conventions in This Guide ...............................................................................................x

Caution Labels .......................................................................................................................... xii

Installation Precautions .............................................................................................................xiii

Precautions for Use .................................................................................................................. xiv

Introduction .................................................................................................................................................xxiii

Guides Included ......................................................................................................................xxiv

Conventions in This Guide ......................................................................................................xxiv

1 Part Names ..................................................................................................... 1-1

Copier .......................................................................................................................................1-2

Document Processor ................................................................................................................1-4

Internal Parts ............................................................................................................................1-5

Operation Panel .......................................................................................................................1-6

Touch Panel .............................................................................................................................1-7

2 Preparing to Copy .......................................................................................... 2-1

Loading Paper ..........................................................................................................................2-2

Specifying Paper Type and Size to the Cassettes and MP Tray ..............................................2-8

Loading Originals ...................................................................................................................2-16

Selecting the Language .........................................................................................................2-20

3 Basic Operation ............................................................................................. 3-1

Basic Copying Procedures .......................................................................................................3-2

Selecting Image Quality ...........................................................................................................3-4

Adjusting Exposure ..................................................................................................................3-5

Reducing/Enlarging ..................................................................................................................3-6

Duplex Mode ..........................................................................................................................3-11

Split Mode ..............................................................................................................................3-14

Sort Mode ...............................................................................................................................3-16

Interrupt Mode ........................................................................................................................3-17

Job Reservation .....................................................................................................................3-18

Low-Power Mode ...................................................................................................................3-19

Sleep Mode ............................................................................................................................3-20

4 Optional Equipment ....................................................................................... 4-1

Overview of Optional Equipment ..............................................................................................4-2

Side Feeder ..............................................................................................................................4-3

Document Finisher ...................................................................................................................4-3

Key Counter .............................................................................................................................4-3

Printer Kit .................................................................................................................................4-4

Scanner Kit ...............................................................................................................................4-4

Security Kit ...............................................................................................................................4-4

5 Maintenance ................................................................................................... 5-1

Cleaning the Copier .................................................................................................................5-2

Replacing Toner Container .......................................................................................................5-4

6 Troubleshooting ............................................................................................. 6-1

Solving Malfunctions ................................................................................................................6-2

Responding to Error Messages ................................................................................................6-4

xxv

Clearing Paper Jams ............................................................................................................... 6-9

Appendix .....................................................................................................Appendix-1

Specifications ............................................................................................................. Appendix-2

Index ................................................................................................................... Index-1

xxvi

1Part Names

This chapter identifies copier parts and operation panel keys.

• Copier...1-2

• Operation Panel...1-6

• Touch Panel...1-7

1-1

Part Names

Copier

12

3

8

10

9

5

4

6

7

1 Operation Panel

2 Operation Panel Lock Lever

3 Document Processor

4 Cassette 1

5 Cassette 2

6 Cassette 3

7 Cassette 4

8 MP Tray (multi-purpose tray)

9 Paper Width Guides

10 MP Tray Extension

11 Right Cover

12 Handles

12

11

1-2

Part Names

13

14

15

16

17

19

18

20

21

13 Main Power Switch

14 Main Power Switch Cover

15 Document Processor Bottom Cover

16 Original Size Indicator Plates

17 Platen

18 Front Cover

19 Output Tray (Option)

20 Handles

21 Power Cord

1-3

Part Names

Document Processor

26

22 Original Table

23 Original Width Guides

24 Cleaning Cloth Compartment

25 Original Loaded Indicator

26 Document Processor Top Cover

27 Ejection Guide

28 Document Processor Angle Adjustment Lever

29 Original Eject Table

25

2223

24 23

27

28

29

1-4