Triumph Daytona 955i 2002, Daytona 955cc 2002 Service Manual

Specifications and Main Features

Configuration of Engine: In this engine there are engines mounted droplet which consists of a small over interleaved.
Arrangement: 3-inline configuration with Secondary Rotational Axes Set Forward
Volume: this engine has a volume of 955 cc
Cylinder Dimensions: the engine has an internal diameter of 79mm and a stroke length of 65mm.
Inscription Order: The alignment begins from the left moving towards the right. (No.3 is in close proximity to the stretch of cam chain)
Max Power Capacity: The Speed Triple consists of 120PS @ 9100 RPM and Daytona with 149PS @ 10700RPM.
Maximum Torque: The Speed Triple has torque power of 100NM @ 5100RPM while the Daytona has 100NM @ 8200 RPM.

Cylinder Head/Valves

Head Of The Valve: The head of the valve has an inset of 33.5 mm for inlets and 27 mm for exhausts.
Lift Of Valves: Inlets have a lifting measure of 10.15mm while exhausts have a lifting measure of 9.65mm.
Grace Limit for tests;

Valve Clearance: Inlet uses 0.9-1.1mm while Exhaust applies 1.5mm

Seat Angle: The angle of the seat is 45 degrees.
Outlet and Inlet: The valve bore diameter for both the inlet and outlet is 28.476-28.490mm and 28.515-28.535 respectively.

Pistons

Bore Measure of Cylinder: For a speed triple diameter ranges from 79.030 – 79.050 mm while the Daytona falls in the bracket of 78.985 – 79.003 mm.
Nipple Pin: For speed Triple the range is 18.995 to 19.000 mm and for Daytona the limit is set from 16.984 to 16.989.

Transmission

Broad Picture: Nap is the type of constant mesh used for six gears.
Ratios: The gears apply this ratio first 2.733, 2, second 1.947, and 3rd 1.545 , the fourth gear uses 1.291 while the fifth adds 1.154 and the last one concludes at 1.074

Final drive

Type: Chains us used for drive.
Ratio: Single sided makes use of 2.333 for a pair of 18 and 42 while the twin sided two gets 2.316 from 19 and 44.

Lubrication

Electronics

Cooling Mechanism

Brakes

Front: Two Four Piston Calipers Axial And Radial acting on twin discs (Disc Dia.: 320 mm).
Rear: A Hydraulic 2 Piston Caliper on Single Discs (Disc Dia.: 220 mm).

Wheels and Tyres

Chassis

Q 1: In terms of engine capacity, does the Speed Triple differ from the Triumph Daytona 955i?

A: Definitely Not: The engine capacity of both the Speed Triple and the Triumph is 955 cc.

Q 2: Can you set forth the lube system used?

A: Well, it is only wet sump with pressure lubrication.

Q3: What is the highest Power output generated by the Speed Triple in Combination with the Daytona?

A3: Speed Triple achieves a maximum PS of 120 at an RPM of 9100, while the Daytona reaches an RPM of 149 PS at 10700.

Q4: What is the maximum limit for the fuel tank size for both vehicles?

A4: Both the Speed Triple and the Daytona have a vertical fuel tank size of 22 litres.

Q5: For how many years is the brake fluid supposed to be replaced for these motorcycles?

A5: The duration to replace the brake fluid is every 2 years on these motorcycles as per the standards.

Q6: Are there specific tires that can be used for these models?

A6: Yes, the motor's handbook contains exact specifications for the recommended tires that can be used.

Q7: What is the measure of oil which is required for both types of motorcycles?

A7: An oil measure of 3.50 litres(dry fill) is required in order for the two models to function.

+ 380 hidden pages