XP
Model FT7000
QUICK REFERENCE GUIDE
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
TDN 07102-00071
04/2007
MANAGEMENT FUNCTIONS
- ACCESS INSTRUCTIONS -
1. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE <CTRL> KEY (LOWER-RIGHT CORNER OF KEYPAD),
PRESS <1> KEY, THEN RELEASE BOTH KEYS. THE SECURITY LOGIN SCREEN WILL BE DISPLAYED.
2. ENTER THE 2-DIGIT USER ID. PRESS <ENTER> KEY. ENTER THE USER PASSWORD AND PRESS <ENTER> KEY.
THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED.
RESTART / SHUTDOWN TERMINAL
RESET ATM: FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT
FUNCTIONS. SELECT SYSTEM PARAMETERS, THEN RESTART TERMI-
NAL.
SHUTDOWN TERMINAL: FOLLOW A CCESS INSTRUCTIONS TO ENTER
MANAGEMENT FUNCTIONS. SELECT SYSTEM PARAMETERS, THEN
SHUTDOWN TERMINAL. NOTE: THIS OPTION POWERS DOWN THE PC ONLY!
VIEW / CLEAR ATM SETTLEMENT TOTALS
THE VIEW ATM SETTLEMENT TOTALS DISPLAYS THE TOTAL NUMBER OF
CAPTURED
THE START DATE IS THE LAST ATM SETTLEMENT R ESET DAY AND THE END DATE
THE CURRENT DATE. THE SETTLEMENT TOTALS ARE NOT CLEARED.
IS
CARDS AND DISPENSED CURRENCY WITH THE START AND END DATES.
THE CLEAR ATM SETTLEMENT TOTALS RESETS ALL THE ATM SETTLE-
MENT TOTALS TO ZERO (0) AND RESETS THE START DATE TO THE CURRENT DATE/
TIME.
!!
! FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL SETTLEMENT
!!
FUNCTIONS. CHOOSE VIEW ATM SETTLEMENT TOTALS. SELECT <PRINT> OPTION TO PRINT A REPORT.
REAR DISPLAY HOST SETTLEMENTS
!!
! PRESS THE <ALT> AND “R” KEYS ON THE REAR KEYBOARD.
!!
!!
! WHEN PROMPTED, ENTER THE PIN NUMBER OF THE SETTLEMENT CARD.
!!
!!
! THE HOST/PROCESSOR SETTLEMENT SCREEN APPEARS. NOTE: OPTIONS
!!
MAY VA RY DEPENDING ON THE HOST.
2
REPLENISH CASSETTE(S)
THE REPLENISH CASSETTE(S) FUNCTION ALLOWS USER TO REPLENISH THE
(CURRENCY, COUPONS, ETC) IN THE CASSETTE(S).
MEDIA
!!
! FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
!!
LECT TERMINAL SETTLEMENT FUNCTIONS. CHOOSE REPLENISH
CASSETTE(S).
!!
! A SCREEN WARNING APPEARS THAT THE TIMEOUT FUNCTION NOR-
!!
MALLY ASSOCIATED WITH MANAGEMENT FUNCTIONS IS DISABLED. PRESS
<1> TO CONTINUE.
Note: The Fujitsu 510 dispenser does not have the capability to
lock/unlock cassettes. Cassette(s) may be removed/inserted at any
time.
!!
! A SCREEN IS DISPLAYED THAT ALL CASSETTE(S) MAY BE REMOVED.
!!
< FOLLOW THE CASSETTE REPLENISHMENT PROCEDURES >
!!
! PRESS <1> TO RETURN TO TERMINAL SETTLEMENT FUNC-
!!
TIONS.
ELECTRONIC JOURNAL
- DISPLAY LAST X -
THE DISPLAY LAST X FUNCTION IS USED TO DISPLAY AND PRINT RECORDS
THE ELECTRONIC JOURNAL. RECORDS PRINTED USING THIS COMMAND
FROM
NOT MARKED IN ANY WAY. THIS FUNCTION WILL NOT AFFECT ANY OTHER
ARE
JOURNAL
!!
! FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGE-
!!
MENT FUNCTIONS. SELECT ELECTRONIC JOURNAL.
CHOOSE DISPLAY LAST X RECORDS.
!!
! PRESS <1> TO HIGHLIGHT THE NUMBER OF RECORDS
!!
TO
KEY.
!!
! PRESS <2>, PERFORM QUERY, TO DISPLAY THE RECORDS. SELECT <PRINT> OPTION TO PRINT THE REPORT.
!!
FUNCTIONS.
DISPLAY. ENTER AN AMOUNT (#), THEN PRESS <ENTER>
3
REPLENISH CASSETTE(S) - NMD-100
STEP
UNLOCK / OPEN CABINET.
1
ACTION
GRASP NOTE CASSETTE
HANDLE
WHILE
NISM WITH THE OTHER. PULL
THE
SLIGHTLY
HAND
SLIDE
PLACE CASSETTE ON A LEVEL SURFACE. INSERT KEY
2
INTO
WITH ONE HAND
HOLDING THE MECHA-
CASSETTE OUT
, THEN PLACE ONE
UNDERNEATH AS YOU
IT OUT.
THE CASSETTE LOCK AND TURN CLOCKWISE. PRESS
GREEN RELEASE BUTTON TO RAISE LID.
MOVE PUSHER PLATE TOWARDS THE CASSETTE HANDLE.
3
PLATE SHOULD STAY INPLACE. LOAD NOTES USING 1" -
2" STACKS OF CURRENCY.
STEP
EXTEND “PAWLS” FULLY (IN-
5
SERT) ON THE PUSHER PLATE.
CLOSE CASSETTE LID TO ITS
6
LOCKED
POSITION. THE
ACTION
GREEN RELEASE BUTTON
“POP” OUT. TURN
SHOULD
COUNTERCLOCKWISE TO
KEY
CASSETTE. SLIDE CAS-
LOCK
SETTE INTO ITS SLOT IN THE
MECHANISM
REMOVE REJECT CASSETTE FROM MECHANISM. PLACE
7
LEVEL SURFACE. INSERT KEY INTO LOCK AND TURN
ON
CLOCKWISE
.
LID
.
. PRESS GREEN RELEASE BUTTON TO RAISE
LEVEL NOTE PILE BY HAND. MOVE PUSHER PLATE
4
AGAINST
NOTES
THE NOTES WITH ENOUGH PRESSURE TO HOLD
BEFORE CLOSING.
REMOVE ANY REJECTED NOTES - BOTH SINGLE AND
8
BUNDLED
AREAS. FOLLOW LOCKING PROCEDURES FROM
STEP 6 AND SLIDE CASSETTE BACK INTO MECHANISM.
Single Note Reject
Area
Bundled Note Reject
Area
4
REPLENISH CASSETTE(S) - FUJITSU 510
STEP
!!
! UNLOCK / OPEN CABINET.
!!
1
""
" GRASP CASSETTE HANDLE AND
""
GREEN RELEASE BUTTON.
PUSH
##
# PULL CASSETTE OUT SLIGHTLY,
##
THEN PLACE ONE HAND UNDERNEATH
YOU SLIDE IT OUT.
AS
!!
! PLACE CASSETTE ON FLAT SUR-
!!
2
FACE.
""
" OPEN CASSETTE BY SLIDING
""
LEVER TO RIGHT AND LIFT LID.
LATCH
##
# FLIP LID BACK FULLY.
##
REMOVE ANY REJECTED NOTES FROM
AREA. NOTE: ONLY THE
REJECT
TOP CASSETTE ACCEPTS REJECTS.
$$
$ HOLD GREEN KNOB AND PULL
$$
PRESSURE
REAR
%%
% RELEASE KNOB AND ENSURE
%%
PLATE
&&
& LOAD NOTES USING 1" - 2"
&&
STACKS OF CURRENCY.
!!
! MOVE PRESSURE PLATE
!!
3
AGAINST
PRESSURE
CLOSING
""
" FOLD CASSETTE LID DOWN TO
""
ITS
SETTE BACK INTO THE MECHANISM.
PLATE BACK TOWARDS
.
IS LATCHED.
THE NOTES WITH ENOUGH
TO HOLD NOTES BEFORE
LID.
LOCKED POSITION. INSERT CAS-
ACTION
Release button
Lid latch
* IMPORTANT *
BEFORE INSERTING CASSETTES IN THE FEED CHAN-
NELS, ENSURE THE OPEN/CLOSE TAB ( LOCATED IN
CHANNEL) IS IN THE “CLOSE” POSITION. THE
EACH
SHOULD BE IN THE POSITION SHOWN BELOW. IF
TAB
, BILL FEED ERRORS WILL OCCUR!
NOT
5
REPLACE PAPER (RECEIPT PRINTER)
STEP
OPEN UPPER LEFT CABINET DOOR.
1
ACTION
PULL UP ON THE LOCKING PIN AND
PRINTER ASSEMBLY TRAY
EXTEND
.
FULLY
REMOVE EXISTING PAPER ROLL AND/
4
OR SPINDLE FROM PAPER SUPPORT
BRACKET
.
STEP
IF PAPER REMAINS ON ROLL, CUT
2
BETWEEN
PRINTER
PLACE SPINDLE IN NEW PAPER ROLL.
5
ACTION
THE ROLL AND INPUT TO
.
CUT OFF ANY PAPER WHERE THERE
GLUE PRESENT.
IS
STEP
PUSH UP ON THE FEED BUTTON
3
ACTION
(BLUE) REPEATEDLY TO ADVANCE
REMAINING
PAPER FROM FEED PATH .
Feed button
ALIGN PAPER ROLL (W/SPINDLE) IN
6
SUPPORT BRACKET SLOTS.
PAPER
ENSURE PAPER FEEDS FROM BOT-
TOM!
PASS END OF PAPER OVER THE TEN-
7
SION ROLLER AND INSERT INTO THE
PRINTER
WILL
TAKE-UP SLOT. PRINTER
AUTOMATICALLY GRAB PAPE R.
FROM REAR SERVICE PANEL - ENTER MANAGEMENT FUNCTIONS >
8
DIAGNOSTICS > PRINTER. SELECT OPTION <3>, RESET. THE
PRINTER
WILL RESET AND DISPLAY A STATUS REPORT. SELECT <PRINT>.
THE REPORT WILL PRINT TO THE RECEIPT PRINTER. PUSH PRINTER TRAY
INTO CABINET. THE PRINTER IS NOW READY.
BACK
6
PAPER SPECIFICATIONS
P
APERSPECIFICATION S
htdiW)1-/0+(mm08"8/1-3
retemaiDmm452otpu"01otpu
)edisni(retemaideroCmm52~"1
)ylp(ssenkcihTrepaP
PRINTER ACCESS AREAS
GREEN MARKINGS ON ASSEMBLY ARE DESIGNATED ACCESS AREAS.
##
#
##
054DP
)snorcim4-/+16(053P
)snorcim5-/+26(
$$
$
$$
""
"
""
!!
!
!!
7
REPLENISH ENVELOPES (ENVELOPE SUPPLY UNIT)
THE OPTIONAL ENVELOPE SUPPLY UNIT HOLDS APPROXIMATELY 200 ENVELOPES. WHEN LOADING ENVELOPES, ALTER-
NATE EVERY 50-100 WITH THE FLAPS UP. FOR EXAMPLE, LOAD 50 WITH FLAPS UP FACING LEFT, THEN NEXT 50 WITH
UP FACING RIGHT. THE ENVELOPE SIZE REQUIREMENTS ARE AS FOLLOWS:
FLAPS
tnemeriuqeReziSepolevnE
s
htgneL htdiW ssenkcihT
muminiM]"19.5[mm051]"57.3[mm59
mumixaM]"6.9[mm442]"52.4[mm801
1. OPEN UPPER LEFT REAR CABINET DOOR. PULL UP ON TRAY LOCKING
AND PULL THE ENVELOPE DEPOSITORY UNIT SLIDE TRAY OUT FULLY.
PIN
2. FOLLOWING THE INSTRUCTIONS ON INSERTING ENVELOPES (LABEL ON
), LOAD ENVELOPES (FLAP UP INTO THE SUPPLY BIN). SLIDE TRAY BACK
UNIT
THE CABINET.
INTO
* NOTE *
REMEMBER TO ALTERNATE EN-
VELOPES APPROXIMATELY EVERY
50 WITH FLAPS UP FACING LEFT-
RIGHT.
]"72.[mm7
)mm1.832xmm8.401(epolevne01#asiezisdednemmoceR:etoN
3. ACCESS MANAGEMENT FUNCTIONS AND FROM THE MAIN MENU SCREEN
DIAGNOSTICS > ENVELOPE DEPOSITORY > ENVELOPE DISPENSE AND
SELECT
RETRACT TEST.
THE TEST DISPENSES AN ENVELOPE AND THEN AUTOMATICALLY RETRACTS IT
THE DEPOSITORY STORAGE BIN (NORMAL OPERATION).
INTO
4. AFTER THE TEST IS COMPLETE, PRESS <2> TO EXIT.
8
REPLACE RIBBON CARTRIDGE (ENVELOPE DEPOSITORY UNIT)
THE OPTIONAL DEPOSITORY ACCEPTS AN ENVELOPE, MONITORS ITS PROGRESS THROUGH THE UNIT, STAMPS IT WITH
IDENTIFYING
ENVELOPE
1. REMOVE RIBBON CARTRIDGE FROM THE FOUR (4) PLASTIC TABS THAT HOLD IT.
2. MOUNT THE NEW RIBBON CARTRIDGE INTO THE PRINTER HOLDER AS SHOWN BELOW. ENSURE CARTRIDGE ALIGNS
WITH
DATA (UP TO 68 CHARACTERS WITH THE DOT MATRIX PRINTER), AND DEPOSITS THE ENVELOPE IN THE
DEPOSIT BIN.
THE PLASTIC TABS.
3. CONFIRM THAT THE RIBBON IS POSITIONED BETWEEN THE MASK AND HEAD, THEN TURN THE RIBBON KNOB IN A
“CLOCKWISE” DIRECTION UNTIL TAUT.
9
ELECTRONIC LOCK (LaGard)
ENTERING THE COMBINATION
THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX (6) DIGITS. IF LOCK IS
PROGRAMMED
THE PRESET COMBINATION OF THE LOCK SHOULD ALREADY BE SET AT 1-2-3-4-
5-6. AFTER INSTALLATION OF THE UNIT HAS BEEN COMPLETED, PERFORM THE
FOLLOWING
FOR DUAL CODE OPERATION, THE SECOND CODE MUST BE ENTERED
WITHIN
1. ENTER THE PRESET COMBINATION(S) AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS, THE LOCK
WILL
WILL
2. WITHIN FOUR (4) SECONDS, TURN THE KEYPAD “CLOCKWISE” TO THE OPEN POSITION.
3. AFTER THE LOCK IS OPENED, THE DOOR MAY BE OPENED.
INVALID CODE ENTRY - LOCK WILL BEEP THREE (3) TIMES.
FOR DUAL CODE, EACH CODE WILL CONSIST OF SIX (6) DIGITS.
STEPS:
* NOTE *
TEN (10) SECONDS AFTER THE FIRST CODE WAS ENTERED.
BEEP. AFTER THE FINAL DIGIT HAS BEEN ENTERED, THE LOCK WILL BEEP TWICE AND THE OPEN PERIOD
BEGIN.
CHANGING THE COMBINATION
* IMPORTANT *
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN!
IF YOUR UNIT IS PROGRAMMED FOR DUAL CODE, EACH CODE MUST BE CHANGED INDEPENDENTLY. FOLLOW
INSTRUCTIONS FOR EACH CODE CHANGE.
THESE
TO CHANGE THE COMBINATION OF THE LOCK, SIMPLY FOLLOW THESE DIRECTIONS.
1. ENTER SIX (6) ZEROS.
2. ENTER THE CURRENT COMBINATION (INITIALLY SET AT 1-2-3-4-5-6).
3. ENTER THE NEW SIX (6) DIGIT COMBINATION TWICE.
- IF A MISTAKE IS MADE, WAIT THIRTY (30) SECONDS AND REPEAT THE FIRST 3 STEPS.
4. TEST LOCK COMBINATION SEVERAL TIMES BEFORE CLOSING THE DOOR. THE COMBINATION IS NOW CHANGED.
VALID CODE ENTRY - DOUBLE SIGNAL AFTER VALID SIX (6) DIGIT CODE IS ENTERED.
INVALID CODE ENTRY - TRIPLE SIGNAL AND OLD CODE IS STILL VALID.
10
ELECTRONIC LOCK (LaGard)
SILENT SIGNAL A LARM
(IF FEATURE IS PROGRAMMED AND OPTIONAL ALARM B OX IS CONNECTED TO AN ALARM SYSTEM)
- ALWAYS PERFORM THIS OPERATION WITH THE DOOR(S) OPEN!
1. ENTER LAST DIGIT OF CODE ONE (1) NUMBER HIGHER OR ONE (1) NUMBER LOWER.
EXAMPLE:CODE: 1-2-3-4-5-6
DURESS: 1-2-3-4-5-5 OR 1-2-3-4-5-7
2. THE LOCK WILL OPEN WITHOUT ANY INDICATION THAT THE DURESS SIGNAL HAS BEEN SENT.
LOCKOUT FEATURE
THE LOCK INCLUDES A WRONG TRY PENALTY LOCKOUT FEATURE THAT PREVENTS ENTRY FROM UNAUTHORIZED
PERSONNEL
•ENTRY OF FOUR (4) CONSECUTIVE INVALID COMBINATIONS STARTS A 5-MINUTE DELAY PERIOD.
•AT THE END OF THE DELAY PERIOD, TWO (2) MORE CONSECUTIVE INVALID COMBINATIONS WILL RESTART AN ADDITIONAL
. THIS FEATURE PERFORMS AS FOLLOWS:
- LED FLASHES RED AT TEN (10) SECOND INTERVALS.
5-MINUTE DELAY. ENTRY WILL NOT RESPOND TO A SINGLE KEYSTROKE DURING DELAY PERIOD.
BATTERY LOW W ARNING
REPEATED BEEPING DURING AN OPENING INDICATES THAT THE BATTERY IS LOW AND NEEDS TO BE REPLACED. RECOM-
MEND REPLACEMENT OF BATTERY AT LEAST ONCE ANNUALLY. THE BATTERY BOX IS LOCATED ON THE INSIDE OF THE DOOR.
NOTE: IF THE LOCK WILL NOT OPERATE (I.E. REPEATED BEEPING OR NO BEEPING) WHILE THE DOOR IS CLOSED AND LOCKED, THE
MUST BE ENERGIZED FROM THE TWO EXTERNAL TERMINALS ON THE FRONT OF THE PUSH-BUTTON PANEL.
BATTERY
TO ENERGIZE THE LOCK, CONNECT A 9-VOLT ALKALINE BATTERY ON THE EXTERNAL TERMINAL POINTS. MAINTAIN
CONTACT
, ENTER A VALID COMBINATION, AND TURN THE DIAL CLOCKWISE TO OPEN THE LOCK.
NOTE: YOU MUST MAINTAIN BATTERY CONTACT AT ALL TIMES THROUGHOUT THIS PROCEDURE.
CHANGING THE BATTERY
1. OPEN THE ATM VA U L T DOOR(S). REMOVE THE BATTERY BOX COVER BY PULLING THE FRONT PORTION AWAY FROM
VAULT DOOR.
THE
2. THE CONNECTOR IS EASILY REMOVED BY UNSNAPPING IT FROM THE TWO (2) TERMINAL ON THE TOP OF THE BATTERY.
3. REMOVE THE OLD BATTERY. INSTALL/CONNECT A NEW 9-VOLT ALKALINE BATTERY.
4. PUSH THE BATTERY AND THE LEADS COMPLETELY UP INTO THE BATTERY COMPARTMENT.
5. REINSTALL THE COVER AND TEST THE UNIT SEVERAL TIMES BEFORE CLOSING THE VAULT DOOR.
11
ENVELOPE DEPOSIT BIN
THE SECURE ENVELOPE DEPOSIT BIN STORES DEPOSIT TRANSACTIONS. THE CUSTOMER INSERTS AN ENVELOPE CON-
TAINING CHECKS OR BILLS (NOT COINS), THE DEPOSITORY UNIT ACCEPTS THE ENVELOPE, STAMPS IT, AND DEPOSITS IN
ENVELOPE BIN.
THE
RECOMMENDATION
THE ENVELOPE D EPOSITORY STAMPS DEPOSITED ENVELOPES WITH IDEN-
TIFYING DATA. THIS DATA IS STAMPED APPROXIMATELY IN THE MIDDLE
THE ENVELOPE AS SHOWN IN THE FIGURE AT RIGHT. IF YOUR ENVE-
OF
LOPES HAVE A LOGO/GRAPHIC THAT IS AT OR NEAR THE CENTER, THIS
WILL PRINT OVER THIS AND MAY MAKE IDENTIFICATION HARD TO
DATA
DETERMINE
NERS OR USE PLAIN ENVELOPES.
. RECOMMEND EITHER MOVING YOUR LOGO UP TO THE COR-
REMOVE:
1. OPEN LOWER (LEFT) REAR CABINET DOOR. PULL THE BIN OUT SLIGHTLY, THEN PLACE ONE HAND UNDERNEATH AS
SLIDE IT OUT FROM THE GUIDE RAILS.
YOU
2. INSERT THE KEY AND TURN IT 90° CLOCKWISE. CLOSE THE COVER (HELD BY A MAGNET). TURN THE KEY BACK TO
.
SECURE
MOUNT:
1. INSERT THE KEY AND TURN IT 90° CLOCKWISE. OPEN THE COVER (HELD BY A MAGNET). TURN KEY BACK TO
.
REMOVE
2. WITH ONE HAND UNDERNEATH BIN, GRASP HANDLE AND SLIDE BACK INTO THE GUIDE RAILS. SLIDE THE BIN
FORWARD
UNTIL IT “CLICKS”.
12
Loading...