Assembly Instructions
SmartRack® 4-Post
Heavy-Duty Open Frame Racks
Models: SR4POST48HD, SR4POST50HD, SR4POST52HD, SR4POST58HD
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $50 value!
www.tripplite.com/warranty
1111 West 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2014 Tripp Lite. All trademarks are the sole property of their respective owners.
1
Parts List
A B C D E F
Front Upright Rear Upright Top Flange Base Flange Horizontal Beam PDU Bracket
x2x2 x4
x2x2 x2
SRCASTER Kit (Optional, Sold Separately)
G H I
M10 Acorn Nut M10 Flat Washer M6x12 Phillips
Head Screw
M6x16mm Hex
J K L M
M6 Hex Nut M6 Flat Washer Caster
Head Screw
x16 x16 x4 x16 x16 x32 x4
Required tools (User Supplied):
• Phillips Head Screwdriver
• 16 mm Open End Wrench
WARNING: The rack enclosure is extremely heavy. Do not attempt to unpack, move, assemble or install the
enclosure without assistance. Until it has been properly assembled and stabilized, the enclosure is prone to
tipping and could cause property damage and/or personal injury. Use extreme caution when assembling
the enclosure. Do not attempt to install equipment without first stabilizing the enclosure.
2
step
1
Lay out parts
on the floor or a
stable work surface
and assemble as
shown.
A B
1 1
E
2
step
2
Attach the washers and acorn
nuts, but leave them loose.
This will allow the unit to flex
later in the assembly process.
C
2
G
H
4
4
3
step
3
Attach the washers
and acorn nuts, but
leave them loose.
D
2
G
4
H
4
step
4
E
2
4
step
5
Lay rear upright on the
unit. Pull apart the base
flange and horizontal
beam 1. Align the
holes at the end of the
upright with the studs
in the horizontal beam
and push the upright
onto the beam 2. Push
the base flange and
horizontal beam back
together.
A B
1 1
step
6
Attach the
washers and
acorn nuts, but
leave them
loose.
2
1
x2
Repeat this process for the other end of the upright.
G
H
4
4
Repeat steps 5 & 6 to attach front upright.
5
step
7
Using an open
end wrench (usersupplied), tighten
all acorn nuts
firmly. Place the
rack upright on a
level surface and
confirm it’s stable.
step
x16
8
(Optional)
Attach PDU
Brackets
F
2
I
4
6
step
9
(Optional)
Attach Casters
Warning: Do not
attempt to install
casters while
equipment is
installed in the rack.
Note:
Installation requires
Tripp Lite’s HeavyDuty Rolling Caster
Kit (model SRCASTER,
sold separately)
K
M
J
x4
16
Configuration 1 Configuration 2
16
L
32
4
7
step
10
(Optional)
Attach Side Panels
(sold separately)
SR4POST48HD
SR4POST50HD
SR4POST52HD
x2
SR48SIDE4PHD
SR50SIDE4PHD
SR52SIDE4PHD
x2
SR4POST58HD
SR58SIDE4PHD
Warranty and Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date
of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN
THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY
OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES.
(Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are
subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See Web site for details.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change without notice.
1111 West 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
8
14-08-120 • 9333B4_revA
Loading...