Tripp Lite PDU Series, PDUV30HV, PDUMV30HV, PDUMV30, PDUMV16HV Owner's Manual

Owner’s Manual

Metered Rack PDU

Models: PDUV30HV, PDUMV30, PDUMV16HV,

PDUMV20HV, PDUMV30HV

(Series Number: AGIB6672, AGPD6673, AGPD6674, AGPD6675)

Español 6 • Français 11 • Русский 16 • Deutsch 21

PROTECT YOUR INVESTMENT!

Register your product for quicker service

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Copyright © 2019 Tripp Lite. All rights reserved.

1

18-11-318-933312.indb 1 3/20/2019 1:22:51 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be
followed during the installation, operation and storage of this
product. Failure to heed these instructions and warnings will void
the product warranty.

Important Warnings

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or
line noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from
excess moisture, temperature extremes, conductive contaminants, dust or direct
sunlight.

• The PDU must be installed by a qualified technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Codes. Be sure to use the proper over
current protection for the installation, in accordance with the plug rating/equipment
rating as follows:

Model Series Number Overcurrent Protection

PDUV30HV AGIB6672 30A
PDUMV30 AGPD6673 30A
PDUMV16HV, PDUMV20HV AGPD6674 20A
PDUMV30HV AGPD6675 30A

• Short-circuit backup protection and overcurrent protection is provided by the building
installation.

• The electrical outlets supplying power to the equipment should be installed near the
equipment and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters
that eliminate the connection to ground.

• The plug on the power supply cord is intended to serve as the disconnect device.
Be sure that the socket-outlet is installed near the equipment and is made easily
accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• The power requirement for each piece of equipment connected to the PDU must not
exceed the individual outlet’s load rating.

• The total power requirement for equipment connected to the PDU must not exceed the
maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user­serviceable parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

2

18-11-318-933312.indb 2 3/20/2019 1:22:51 PM

Important Safety Instructions

• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended.

Installation

Note: The user must determine the fitness of hardware and procedures before mounting. The PDU and included
hardware are designed for common rack and rack enclosure types and may not be appropriate for all applications.

1A

0U Rack Configuration (Mounting
Brackets). Prior to installation,

determine the rack location in which
the PDU is to be installed. Attach the
mounting brackets to the back of the
PDU as shown, using the included
screws. To assist with proper positioning,
the brackets have four screw holes each;
make sure that the same two holes are
used to attach each bracket to the PDU.
After attaching the brackets, position the
PDU in the rack and mount it by installing
four user-supplied screws through the
brackets into the rack.

1A

1B

0U Rack Configuration (Mounting
Buttons). Attach the included mounting

buttons to the PDU. Position the PDU as
desired in the rack enclosure, align the
buttons with the rack mounting slots,
and slide the PDU into position.

1C

Under-Counter Configuration. The PDU

1B

may be installed under a counter using
the included mounting brackets. Attach
the mounting brackets to the back of
the PDU as shown in STEP 1A. Secure
the PDU to the underside of the counter
by installing two user-supplied screws
through each bracket into the counter.

1C

3

18-11-318-933312.indb 3 3/20/2019 1:22:51 PM

Features

IEC-60320-C13

IEC-60320-C19

Outlets: During normal operation, the outlets distribute AC power
to connected equipment.

Input Plug: The cord is permanently attached to the PDU and has
an IEC 309 16A plug.

Ammeter: The total electrical current used by the PDU will be
displayed on the digital meter in amperes.

PDUMVROTATEBRKT Mounting Accessory: Use these V-shaped
brackets to mount the PDU with its outlets facing the rear of the
rack.

Mounting Brackets: Use these brackets as an alternate PDU
mounting method.

Mounting Buttons: Come pre-installed on the back side of the
PDU and are used for toolless mounting. Note: Four additional

mounting buttons are included for alternate rack styles.

C14 Plug Sleeve: (Optional) Use the included C14 plastic sleeves
to secure plugs to receptacles. Attach the sleeve to the plug making
sure that the pull tabs remain outside the plug and that the fit is
secure. To unplug equipment properly, use the pull tabs to remove
the plug and sleeve from the receptacle.

C20 Plug Sleeve: (Optional) Use the included C20 plastic sleeves
to secure plugs to receptacles. Attach the sleeve to the plug making
sure that the pull tabs remain outside the plug and that the fit is
secure. To unplug equipment properly, use the pull tabs to remove
the plug and sleeve from the receptacle.

4

18-11-318-933312.indb 4 3/20/2019 1:22:53 PM

Warranty and Product Registration

2-YEAR LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 2 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all
shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609 USA. Seller will pay
return shipping charges. Visit www.tripplite.com/support before sending any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!

** No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been
assigned a unique series number. The series number can be found on the product nameplate label, along with
all required approval markings and information. When requesting compliance information for this product, always
refer to the series number. The series number should not be confused with the marking name or model number of
the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when
customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the
country)

• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

5

18-11-318-933312.indb 5 3/20/2019 1:22:54 PM

18-11-318 93-3312_revC

Manual del Propietario

PDU para montaje en rack

(bastidor) con amperímetro

Modelos: PDUV30HV, PDUMV30, PDUMV16HV,

PDUMV20HV, PDUMV30HV

(Número de Serie: AGIB6672, AGPD6673, AGPD6674, AGPD6675)

English 1 • Français 11 • Русский 16 • Deutsch 21

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Copyright © 2019 Tripp Lite. Todos los derechos reservados.

6

18-11-318-933312.indb 6 3/20/2019 1:22:54 PM

Instrucciones de seguridad importantes

GUARDE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben
seguirse durante la instalación, operación y almacenamiento
de este producto. De no seguirlas, se anulará la garantía del
producto.

Advertencias Importantes

• El PDU proporciona la conveniencia de múltiples tomacorrientes, pero NO proporciona
protección contra sobretensión o ruido en la línea para los equipos conectados.

• El PDU está diseñada solo para uso en interiores en un entorno controlado lejos de
humedad excesiva, temperaturas extremas, contaminantes conductivos, polvo o luz
del sol directa.

• El PDU debe ser instalado solamente por un técnico calificado.

• No intente instalar el PDU en una superficie inestable o no segura.

• Instale de acuerdo con los reglamentos eléctricos locales. Asegúrese de usar para
la instalación la protección adecuada contra sobrecorriente, de acuerdo con la
especificación de la clavija o del equipo como sigue:

Protección Contra

Modelo Número de Serie

PDUV30HV AGIB6672 30A
PDUMV30 AGPD6673 30A
PDUMV16HV, PDUMV20HV AGPD6674 20A
PDUMV30HV AGPD6675 30A

Sobrecorriente

• Conecte el PDU a un tomacorriente que esté de acuerdo a los códigos locales
de construcción y que esté correctamente protegido contra corrientes excesivas,
cortocircuitos y fallas de conexión a tierra.

• Los tomacorrientes eléctricos que suministran energía al equipo deben instalarse
próximos al equipo y ser fácilmente accesibles.

• No conecte El PDU a un toma corriente que no esté a tierra o cables de extensión o
adaptadores que eliminen la conexión a tierra.

• Asegúrese de proporcionar un dispositivo local de desconexión, que sea fácilmente
accesible, en cualquier modelo que esté instalado permanentemente sin una clavija.

• Nunca intente instalar equipos eléctricos durante una tormenta eléctrica.

• El equipo individual conectado al PDU no debe consumir más corriente que la de la
especificación de cada tomacorriente individual del PDU.

•

La carga total conectada al PDU no debe exceder la capacidad de carga máxima del PDU.

• No intente modificar el PDU, las clavijas de entrada o los cables de alimentación.

• No perfore ni intente abrir ninguna parte del gabinete del PDU. No tiene partes a las
que el usuario pueda dar servicio.

7

18-11-318-933312.indb 7 3/20/2019 1:22:54 PM

Instrucciones de seguridad importantes

• No intente usar el PDU si se daña cualquier parte.

• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde
la falla de este equipo pueda consecuentemente causar la falla del equipo de soporte
de vida o afectar significativamente su seguridad o efectividad.

Instalación

Nota: El usuario debe determinar la idoneidad de los materiales y accesorios así como de los
procedimientos antes del montaje. La PDU y el material incluido están diseñados para racks
(bastidores) y cajas de rack (bastidor) comunes, y pueden no ser apropiados para todas las
aplicaciones.

1A

Configuración Cero U para Rack
(Soportes de Montaje). Antes de

la instalación determine la ubicación
en el rack en donde el PDU va a ser
instalado. Fije los soportes de montaje al
respaldo del PDU utilizando los tornillos
incluidos, como se muestra. A fin de
facilitar una colocación adecuada, cada
soporte tiene cuatro perforaciones para
los tornillos; asegúrese que las mismas
dos perforaciones son usadas para fijar
cada soporte al PDU. Después de fijar
los soportes, coloque el PDU en su lugar
en el rack y móntelo instalando cuatro
tornillos, suministrados por el usuario, a
través de los soportes en el rack.

1A

1B

Configuración para bastidor Cero U
(Botones de Montaje). Fije los botones

de montaje, incluidos, al PDU. Coloque
el PDU en la posición deseada en el
bastidor, alinee los botones con las
ranuras de montaje del bastidor, deslice

1B

el PDU para posicionarlo correctamente.

1C

Configuración Bajo el Escritorio. El

PDU puede instalarse bajo un escritorio
utilizando los soportes de montaje
incluidos. Fije los soportes de montaje
a la parte trasera del PDU como se
muestra en el paso 1A. Asegure el
PDU abajo del escritorio instalando dos
tornillos, suministrados por el usuario, a
través de soporte en el escritorio.

1C

8

18-11-318-933312.indb 8 3/20/2019 1:22:54 PM

Características

Tomacorrientes: Durante la operación normal, los tomacorrientes
distribuyen energía de CA al equipo conectado.

IEC-60320-C13

IEC-60320-C19

Clavija de Entrada: El cable está conectado permanentemente al
PDU y tiene una clavija IEC 309 de 16A.

Amperímetro: La corriente eléctrica total usada por la unidad de
distribución de potencia (PDU) será mostrada en el medidor digital,
en amperios.

Accesorio de Instalación PDUMVROTATEBRKT: Use
estos soportes con perfil en V para instalar el PDU con sus
tomacorrientes viendo a la parte posterior del rack.

Soportes de Instalación: Use estos soportes para instalar el PDU.

Botones de Instalación: Vienen instalados en el lado posterior del

PDU y se usan para instalación sin herramienta. Nota: Se incluyen
cuatro Botones de Instalación adicionales para estilos alternos de
rack.

Manguito de Clavija C14: (Opcional) Use los manguitos plásticos
C14 incluidos para asegurar las clavijas a los tomacorrientes.
Acople el manguito a la clavija asegurándose que las pestañas de
tiro permanezcan fuera de la clavija y que la sujeción sea segura.
Para desenchufar correctamente el equipo, use las pestañas de tiro
para retirar la clavija y el manguito del tomacorriente.

Manguito de Clavija C20: (Opcional) Use los manguitos plásticos
C20 incluidos para asegurar las clavijas a los tomacorrientes.
Acople el manguito a la clavija asegurándose que las pestañas de
tiro permanezcan fuera de la clavija y que la sujeción sea segura.
Para desenchufar correctamente el equipo, use las pestañas de tiro
para retirar la clavija y el manguito del tomacorriente.

9

18-11-318-933312.indb 9 3/20/2019 1:22:55 PM