Tripp Lite DWT4585X Users Guide

Owner’s Manual

Tilt Flat Screen

Wall Mount

MODEL: DWT4585X

CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!

200x200/300x300/
400x200/400x400/
600x400/800x400

Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com

Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com

Русскоязычная версия настоящего руководства представлена на веб-сайте компании

Tripp Lite по адресу: www.tripplite.com

Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com

85”

MAX

91 kg

(200 lbs)

MAX

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Copyright © 2014 Tripp Lite. All rights reserved.

14-10-217-9333E3.indd 1 11/5/2014 12:17:24 PM

1

NOTE: Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit www.tripplite.com/support.

• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.

• This product should only be installed by someone of good mechanical ability,
with basic building experience and a full understanding of this instruction
manual.

• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.

• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.

• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the
items, greatly reducing their holding power.

• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.

Warranty & Product Registration

5-Year Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

2

14-10-217-9333E3.indd 2 11/5/2014 12:17:25 PM

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to

installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.

(x1)

(x1)

(x1)

Package M

M5X14 (x4)

M8X30 (x4)

Package W

Anchor Bolt (x6) Concrete Anchor (x6) D8 Washer (x6)

M6X14 (x4)

Washer (x4)

M8X20 (x4)

Small Spacer (x8)

3

M6X30 (x4)

Big Spacer (x4)

14-10-217-9333E3.indd 3 11/5/2014 12:17:25 PM

1a. Mount on Wood Stud Wall

Find and mark the

exact location of

mounting holes

D8 Washer

Anchor Bolt

Drill pilot holes

Fasten the wall
plate onto the
wall

WARNING

• Make sure that mounting screws are anchored into the center of the studs.
Use of a stud finder is highly recommended.

• Installers are responsible to provide hardware for other types of mounting situations.

• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.

4

14-10-217-9333E3.indd 4 11/5/2014 12:17:26 PM

1b. Mount on Solid Brick and Concrete Block

Concrete Anchor

D8 Washer

Anchor
Bolt

Mark the

exact location of

mounting holes

Drill pilot holes

Fasten the wall
plate onto the
wall

WARNING

• When installing wall mounts onto a concrete masonry unit (also known as a CMU or
“cinder block”), verify that the actual concrete thickness is at least 35mm (1-3/8”)
in order to hold the concrete anchors. DO NOT DRILL INTO MORTAR JOINTS! Be sure
to mount the assembled wall-mount plate with the included concrete anchors, D8
washers and anchor bolts onto solid sections of the blocks. The solid sections can
generally be found 25mm (1”) toward the middle of the block from either end. An
electric drill on a slow setting is suggested to drill the hole rather than a hammer
drill so as to avoid breaking out the back of the hole when entering a hollow section.

• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.

5

14-10-217-9333E3.indd 5 11/5/2014 12:17:27 PM

2. Install Adapter Brackets

2-1 For Flat Back Screen

M5X14
M6X14
M8X20

Washer

2-2 For Recessed Back Screen or to
Access A/V Inputs

Top

Note: Choose appropriate screws, washers and spacers
(if necessary) according to the type of screen.

• Position the adapter brackets as close as possible to
the center of the display.

• Firmly secure the adapter brackets onto the display
using the screws and any other necessary hardware
components included with the unit.

Do not over-tighten screws.

Top

M8X20

M6X30
M8X30

or

Washer

Small
Spacer

Big
Spacer

Small
Spacer

Washer

or

Small Spacer
Small Spacer

M8X20
M6X30
M8X30

Washer

M6X30
M8X30

or

Washer

Big Spacer

6

14-10-217-9333E3.indd 6 11/5/2014 12:17:28 PM

3. Hang Display onto the Wall Plate

Wall Wall

Bolt

Using an assistant or mechanical lifting equipment, hook the display with attached adapter brackets over the top
of the mounted wall-plate. Tighten the two bolts on the bottom of the adapter brackets to secure the unit.

4. Adjustment

Tilt
Adjusting
Knobs

+10°

-10°

To adjust the tilt angle, loosen the Tilt Adjusting Knobs located on the sides of the adapter brackets. Once the
display is at the desired angle, retighten the knobs to hold.

Maintenance

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

• Please visit www.tripplite.com/support if you have any questions.

7

14-10-217-9333E3.indd 7 11/5/2014 12:17:29 PM

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

8

14-10-217-9333E3.indd 8 11/5/2014 12:17:31 PM

14-10-217 93-33E3_RevA