Owner’s Manual
Fixed Wall Mount
for Flat and Curved Screens –
Security Version
Model: DWFSC3780MUL
300x300 / 400x200 /
400x400 / 600x400
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании Tripp Lite по адресу: www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
80”
MAX
88 lb.
(40 kg)
MAX
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
1
Important Safety Instructions
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions and warnings contained in this manual. If you have
any questions regarding any of the instructions or warnings, please visit www.tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this
product may cause damage or serious injury.
• This product should only be installed by someone of good mechanical ability, with basic building experience and a full understanding
of this instruction manual.
• Make sure that the mounting surface can safely support the combined load of the equipment and all attached hardware and
components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder
is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Warranty & Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date
of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES
OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are
subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
2
Component Checklist
IMPORTANT: Ensure all parts according to the component checklist have been received prior to installation. If any parts are
missing or faulty, visit www.tripplite.com/support for service.
Wall Plate (x1)
End Cap (x2) Combo Lock (x1)End Cap Screws (x4)
M5 x 14 (x4) M6 x 14 (x4) M6 x 30 (x4)M8 x 20 (x4) M8 x 30 (x4) Washer (x4) Small
Anchor Bolt (x6) Concrete Anchor
Security Bar (x1) Adapter Bracket (x2) Wall Plate
Spacer (x8)
20 mm Washer
(x6)
(x6)
Level (x1)
Big
Spacer (x4)
Installation
1
Assemble the Wall Plate
End Cap
End Cap
Screws
3
Installation
2A
Mount on Wood Stud Wall
Wall Plate Level
55 mm
(2.2 in.)
Find and mark the exact
location of mounting holes
O4.5 mm
O(3/16 in.)
Drill pilot holes
Screw the
assembled wall
plate onto the
wall
20 mm
Washer
Anchor
Bolt
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
4
Installation
2B
Mount on Solid Brick
and Concrete Block
Wall Plate Level
60 mm
(2.4 in.)
Find and mark
the exact
location of
mounting holes
Concrete
Anchor
O10 mm
O(3/8 in.)
Drill pilot holes
Screw the
assembled wall
plate onto the
wall
20 mm
Washer
Anchor
Bolt
WARNING
• When installing wall mounts onto a concrete masonry unit (also known as a CMU or “cinder block”), verify that the actual
concrete thickness is at least 35 mm (1-3/8”) in order to hold the concrete anchors. DO NOT DRILL INTO MORTAR JOINTS!
Be sure to mount the assembled wall-mount plate with the included concrete anchors, D6 washers and anchor bolts onto
solid sections of the blocks. The solid sections can generally be found 25mm (1”) toward the middle of the block from either end. An electric drill on a slow setting is suggested to drill the hole rather than a hammer drill so as to avoid breaking
out the back of the hole when entering a hollow section.
• Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
5
Installation
3
Install Adapter Brackets
3-1 For Flat Back Screen
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.
Firmly secure all screws. Do not over-tighten.
M5 x 14
M6 x 14
M8 x 20
Washer
6
Installation
3-2 For Curved Screen or Recessed Back Screen
M8 x 20
M6 x 30
M8 x 20
M8 x 30
M6 x 30
M8 x 30
M6 x 30
M8 x 30
4
Hang Display
onto the
Wall Plate
Washer Washer Washer Washer
Small
Spacer
Wall
Small
Spacer
Wall
Big
Spacer
Small
Spacer
Spacer
• Using an assistant or mechanical
lifting equipment, hook the display
with attached adapter brackets over
the top of the mounted wall plate.
• Push the safety clamps on the
bottom of the adapter brackets
upward and tighten the two screws
to lock each bracket to the wall
plate.
Big
7
Installation
5
Slide Security Bar through the Mounting Brackets and
Attach Combo Lock to Secure
Security Bar
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
8
Combo
Lock
18-01-207 93-34E8_RevB
Loading...