Tripp Lite DMCS3270XP Users Guide

Owner’s Manual

Mobile Flat-Panel

Floor Stand

Model: DMCS3270XP

Register your product for quicker service and ultimate peace of mind.

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!

200 x 200 / 300 x 300
400 x 200 / 400 x 400
600 x 400

Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com

Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com

Русскоязычная версия настоящего руководства представлена на веб-сайте компании

Tripp Lite по адресу: www.tripplite.com

Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com

70”

MAX

110 lb.
(50 kg)

MAX

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Copyright © 2017 Tripp Lite. All rights reserved.

17-01-289-9336AF-EN.indd 1 2/2/2017 2:38:36 PM

1

NOTE: Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit www.tripplite.com/support.

• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.

• This product should only be installed by someone of good mechanical ability, with
basic building experience and a full understanding of this instruction manual.

• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.

• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.

• Tighten screws firmly, but do not over-tighten. Over-tightening screws can
damage the items, greatly reducing their holding power.

• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.

Warranty & Product Registration

5-Year Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

2

17-01-289-9336AF-EN.indd 2 2/2/2017 2:38:36 PM

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to

installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.

Middle Base

A

Support Plate

F

Connecting Plate

Package M

M5 x 14 Screw (x4)

M-A

M8 x 50 Screw (x4)

M-F

Column

J

M

M6 x 14 Screw (x4)

Washer (x4)

Left Leg

B

Universal Plate

G

M-B

M-G

Right Leg

Plastic Cover (x2)

Camera Shelf

N

M8 x 20 Screw (x4)

M-C

Small Spacer (x8)

M-H

C

H

Plastic Handle

K

DVD Shelf

O

M6 x 30 Screw (x4)

Big Spacer (x8)

Left Cover DRight Cover

Adapter Bracket (x2)

I

Top Cover

Washer (x4)

P

M8 x 30 Screw (x4)

M-D

M-I

E

L

M-E

Package P

M6 x 16 Screw (x8)

Q

M6 x 8 Screw (x6)

V

17-01-289-9336AF-EN.indd 3 2/2/2017 2:38:36 PM

M6 x 25 Screw (x3)

R

M8 x 25 Screw (x4)

W

M4 x 6 Screw (x3)

S

M5 x 8 Screw (x2)

X

3

M4 x 6 Screw (x4)

T

Allen Wrench

Y

M6 x 14 Screw (x2)

U

Wrench

Z

1. Assembling the Base

Q

Y

1) Insert Right Leg C into Middle Base A. Align the holes in the Right Leg to the holes in the Middle Base.
Secure with Screws Q and Allen Wrench Y. Repeat this step for Left Leg B.

2) Each caster can be adjusted independently for fine tuning. Slightly turn the nut with Wrench Z to lower or

raise Middle Base.

Z

2. Attaching the Column to the Base

CAUTION: Hold the inner column
when loosening the screws to adjust
height.

Y Y

Adjust inner Column J to the desired height, then tighten all screws.

4

17-01-289-9336AF-EN.indd 4 2/2/2017 2:38:37 PM

2. Attaching the Column to the Base

K

Place Plastic Handle K on Column.

Attach Column to Middle Base with
Screws W. Tighten all screws, then
tighten Safety Screw R with user­supplied Phillips-head screwdriver.

R

W

Y

Attach Left Cover D and Right Cover E to Legs.

D

E

5

17-01-289-9336AF-EN.indd 5 2/2/2017 2:38:38 PM

3. Installing the Support Plate

L

Attach Support Plate F to Column with Screws U and
user-supplied Phillips-head screwdriver. Attach Top Cover

U

L to Support Plate.

F

4. Installing the Adapter Brackets

Insert Washers P into
back of Universal Plate

G along plate rails.

P

Insert Adapter Brackets I into Universal Plate. Align holes in Adapter Brackets
to holes in Washers. Insert Screws Q, but do not tighten them yet.

Q

Y

6

17-01-289-9336AF-EN.indd 6 2/2/2017 2:38:39 PM

4. Installing the Adapter Brackets

Attach Plastic Covers H to both ends of
Universal Plate using Screws V. Tighten
all screws with user-supplied Phillips­head screwdriver.

H V

min. 200 mm - max. 600 mm

Y

min. 200 mm - max. 400 mm

Adjust Adapter Brackets to fit VESA hole pattern on your display. Tighten all Screws.

NOTE: Verify proper alignment of all holes.

7

17-01-289-9336AF-EN.indd 7 2/2/2017 2:38:40 PM

4. Installing the Adapter Brackets

4.1 For Flat-Back Screens

M-A
M-B
M-C

M-G

Note: Choose the appropriate Screws, Washers and Spacers (if needed) according to the type of screen.

Screw the Adapter Brackets onto the display.

CAUTION: Tighten all screws but do not over tighten.

4.2 For Recessed-Back Screens or Accessing A/V Inputs

M-C

M-G

or

M-H

M-C

M-F M-F M-F

M-G

or or

M-I

Note: Choose the appropriate Screws, Washers and Spacers (if needed) according to the type of screen.

Screw the Adapter Brackets onto the display.

CAUTION: Tighten all screws but do not over tighten.

M-C
M-D
M-E

or or

M-H

M-G M-G

M-H

M-I

M-G M-GM-G

M-I

M-D
M-E

M-H

M-I

M-H
M-I

M-D
M-E

8

17-01-289-9336AF-EN.indd 8 2/2/2017 2:38:41 PM

5. Hooking the Display to the Support Plate

X

Hook Universal Plate onto Support Plate.

CAUTION: Be sure the display is correctly mounted and that the screws are safely tightened
before releasing the display.

Secure by tightening Screws X with user­supplied Phillips-head screwdriver.

6. Installing the DVD Shelf

Plastic

Holder

Lever

Insert the two plastic
holders of DVD Shelf
O into slots.

Close lever to lock
DVD Shelf.

T

Tighten Screws T to
secure.

9

17-01-289-9336AF-EN.indd 9 2/2/2017 2:38:43 PM

7. Cable Management

8. Installing the Camera Shelf

S

T

Attach Camera Shelf N to Connecting
Plate M using Screws S & T. Tighten
screws with user-supplied Phillips-head
screwdriver.

10

17-01-289-9336AF-EN.indd 10 2/2/2017 2:38:44 PM

9. Installing the Connecting Plate

10. Display Orientation

R

Attach Connecting Plate to Column at the
desired height using Screws R. Tighten
screws with user-supplied Phillips-head
screwdriver.

Install at least two Screws V
diagonally to secure the display.

V

Remove the two
screws to rotate the
display 90° clockwise.

or

Retighten the removed screws
into the different hole position
to secure the display.

For Landscape View

For Portrait View

11

17-01-289-9336AF-EN.indd 11 2/2/2017 2:38:45 PM

11. Adjustment

Tighten the knobs to
secure.

+

-

Loosen the knobs to
adjust the display to
the desired angle.

+

-

Y

+5°/-12°

1200mm
1250mm
1300mm
1350mm
1400mm
1450mm
1500mm
1550mm
1600mm

Display panel center
height measured
from floor.

Maintenance

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

• For any additional questions, visit www.tripplite.com/support.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

12

17-01-289-9336AF-EN.indd 12 2/2/2017 2:38:46 PM

17-01-289 93-36AF_RevA