Tripp Lite DSUT1CSU, DNET1, DRS232, DHUB, DTEL2 User Manual

...

Network Dataline

Surge Suppressors

1111 W. 35th Street

Chicago, IL 60609 USA

Customer Service: (773) 869-1234

www.tripplite.com

Tripp Lite Network Dataline Surge Suppressors are designed to protect data and communications equipment against AC transients caused by lightning, electrostatic discharge and ground surges that can enter equipment from the signal lines or chassis ground.

Tripp Lite Network Dataline Surge Suppressors described here protect virtually any pieces of networked equipment using 100Base-T, 10Base-T, 10Base-2 and 10Base-5 Ethernet, Token Ring, RS232, RS422/423/485, parallel, dial-up modems, fax, ISDN, DDS, T-1 and most other communication interfaces.

Installation

1. Make sure the computer, network device or other equipment is logged OFF the network (if applicable). Turn OFF power to the equipment.

2. Disconnect the cable from the equipment to be protected.

3. Connect the Tripp Lite Network Dataline Surge Suppressor directly to the equipment. DB9 and DB25 models are reversible, to work with male or female ports. To change gender, remove the thumbscrews, reverse their direction and reinstall.

4. Attach the green ground wire on the surge suppressor directly to the protected equipment’s chassis. (Except DB9, DB15 and DB25 models.)

Español: p. 5

Français: p. 9

5. Reconnect the cable to the Tripp Lite Network Dataline Surge Suppressor.

NOTE!

The Tripp Lite Network Dataline Surge Suppressor must be properly grounded and positioned as close as possible to the equipment to be protected. For best results, it is required that the length of the signal line and ground wire (if equipped) between the surge suppressor and the protected equipment be kept as short as possible, not to exceed 12 inches (12”). It is best to install the surge suppressor directly to the equipment, as noted above.

NOTE!

Installing a typical Tripp Lite Network Dataline Surge Suppressor is equivalent to adding approximately three feet (3’) of typical data communication cable to a segment.

The Tripp Lite Network Dataline Surge Suppressor does not protect the equipment on the opposite end of the cable. Normally, protection at both ends is recommended.

CAUTION!

When properly installed, the Tripp Lite Network Dataline Surge Suppressor will only protect against surges on the dataline portion of your installation. Simultaneous AC surge suppression/power protection in the form of an ISOBAR® surge suppressor or Tripp Lite UPS system is strongly recommended for complete system/network protection and can also extend Ultimate Lifetime Insurance coverage to connected equipment.

SPECIFICATIONS All surge suppressors listed have component response times of less than 1 picosecond.

Model:

DHUB DHUB-18V

* Supplied with eight 4” RJ45 patch cables.

DRS232

DNET1

DSUT1CSU

DTEL2

Description:

DHUB: RJ45, 8-port ethernet, token ring RS422/423/485, AS400/ Sys3x protector for hubs, repeaters, terminal servers, MUXs, MAUs, etc.*

DHUB-18V: RJ45, 8-port RS 232 protector for multiport serial devices.*

RJ45/RJ11 protector for 100Base-T4, RS-232 on twisted pair (wires 1-8) or ISDN “S/T” interfaces. Supplied with 4” RJ45 patch cable.

RJ45 100Base-T, 10Base-T, Token Ring, RS422, AS400/ Sys3x protector for NICs, hubs, routers, etc. Supplied with 4” RJ45 patch cable.

RJ45/RJ11 protector for nonspan powered T-1 equipment , digital data service CSUs/DSUs, ISDN “U” interfaces or other digital lines. Supplied with 4” RJ45 patch cable.

RJ45/RJ11 for modems, answering and fax machines. Supplied with 4” RJ11 patch cable.

Nominal Clamping Voltage:

7.5 volts, protecting wires 1-8 on all ports.

18 volts, protecting wires 1-8 on all ports.

18 volts, protecting wires 1-8.

7.5 volts, protecting wires 1-8.

60 volts, protecting wires 1-8.

260 volts, protecting center 4 wires (2 COlines).

Peak Pulse Current:

750 amps

340 amps

750 amps

200 amps

250 amps

DB9

DB15AUI

Serial DB9 RS-232 protector for female ports of data terminal and computing equipment including PCs, modems, etc. (any male or female 9 pin port). Male/Female

genders are reversible with reversible thumbscrews.

DB15 ethernet AUI protector.

male or

18 volts, protecting pins 1-9 and chassis.

7.5 and 18 volts, protecting all IEEE

802.3 pins.

340 amps

750 amps

Model:

Description:

Nominal Clamping Voltage:

Peak Pulse Current:

DB25 DB25-ALL

DB25-PAR

D10B5

D10B2-T

Serial DB25 RS-232 protector (wires 1-8,

20) for

male or female ports of data terminal & computing equipment. DB25-ALL: Serial DB25 RS-232 protector (pins 1-25) for any 25 pin male or female DTE/DCE ports. Male/Female

genders are reversible with reversible thumbscrews.

Parallel port DB25 protector (pins 1-25).

10Base-5 thick coax protection with “N” type male/female connectors.

10Base-2 thin coax protected “T” (BNC f/ m/f). Also protects IBM 3270 and CCTV lines.

18 volts, protecting pins 1-8, 20 and chassis.

7.5 volts, protecting pins 1-25 and chassis.

7.5 volts, protecting center, shield and chassis.

340 amps

750 amps

D10B2

10Base-2 thin coax protector (BNC m/f). Also protects IBM 3270 and CCTV lines.

7.5 volts, protecting center, shield and chassis.

DTWINAX

Twinaxial AS400 Sys3x protector (m/f).

10 volts, protecting both signal lines, shield and chassis.

DCATV

Coaxial protector for TVs, VCRs, pro video supplied by CATV (“F” m/f).

Call Tripp Lite Customer Support at (773) 869-1234 for additional applications requiring Multiport, Terminal Strip, RS422/RS423/RS485 or other interfaces.

7.5 volts, protecting center and shield conductors.

750 amps

500 amps

750 amps

LIFETIME LIMITED WARRANTY

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609. Seller will pay return shipping charges. Call Tripp Lite at (773) 869-1234 before sending any equipment back for repair.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction.)

TRIPP LITE

1111 W. 35th Street

Chicago, IL 60609 USA

WARNING: The individual user should take care to determine prior to use whether this

device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.

Policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

+ 8 hidden pages